Search Documents

By Claude Deveau

"Studies on the performance of Falcon batch type concentrators treating ultrafine tantalum at Tanco have revealed that very fine heavy minerals are concentrated within certain areas of the concentrate bed. This information led to the design of a bowl which would allow entrapped lighter low grade particles to escape while providing more space for heavier particles to be recovered in the bed.Numerous tests were then completed with a modified batch-type and non-fluidized Falcon bowl in which the diameter of the discharge lip was adjusted downward manually in steps. This allowed for the gradual building of a higher grade concentrate bed.This work ultimately led to the design of a new Falcon with an automated continuously variable lip. In April 2005, Tanco commissioned the first Falcon UF600.This paper will discuss laboratory scale results and also plant performance of the Falcon’s UF technology.INTRODUCTIONTantalum Mining Corporation of Canada, also known as Tanco, is a wholly owned subsidiary of Cabot Corporation based in Boston, Mass. Operating since 1969, the underground highly mechanized room and pillar operation produces tantalum, lithium and cesium minerals and is located a 2 hour drive east-northeast of Winnipeg Manitoba, Canada.At Tanco, tantalum is recovered using conventional gravity concentration, enhanced gravity concentration and flotation. This paper will discuss how the need for improved equipment to treat very fine tantalum particles was filled by a machine which was modified to the point of creating a completely new technology.In November 2003, Tanco began the investigation for the potential use of a high g-force smooth walled concentrator for treating ultra fine tantalum produced by its flotation circuit. Until then, the tantalum flotation concentrate had been treated by a circuit which consisted of a Mozley Multi-Gravity Separator 902 (MGS), a Mozley MGS 900 and a Bartles cross belt concentrator. Through QemScan analysis, it was found that the majority of the losses from this circuit were of an extremely fine nature which exceeded the recovery limits of equipment on hand. Mean particle size of the tantalum losses was less than 10 µm."

Jan 1, 2006

By Harry Dobroski

Communications with moving tracked vehicles in a rail haulage mine pose a difficult problem. These communications take place from dispatcher to vehicles or from vehicle to vehicle via the trolley line, which is a very poor communications line. As a result, deadspots and high-signal areas can occur anywhere along the line, or signal can decrease simply as a function of distance. An analysis is made of the trolley line as a communications line, and methods of improving its characteristics are discussed. Data from inmine experiments are presented, showing actual improvements in communications. Recent Bureau developments in new hardware are also discussed. These include an adaptive speaker control for existing carrier phones and a new generation of improved carrier phones.

By Albert Wraith, Thomas Price, Wayne Boyd, Skip (I. E. ) Hills, Cameron Harris

Most Peirce-Smith converters inject air through tuyeres, with nitrogen representing the majority of gas passing through the process. The nitrogen controls the temperature of the vessel by carrying away heat from the reactions, both globally and locally at the tuyere tip. However, nitrogen adds energy to the bath and contributes to splashing and limits the blowing rate. High oxygen smelting has made streams of gas containing high concentrations of sulphur dioxide commonplace, which can be used to substitute SO2 for nitrogen and drastically changes Peirce- Smith converting (and all other smelting/converting processes as well). Less SO2 is required to carry away the same quantity of heat, which allows higher concentrations of oxygen and leads to the possibility of increased production. The paper investigates this substitution, its impact on converter productivity, and on the remainder of the plant. 181

Jan 1, 2009

By R. J. Watson, A. H. Juch

About half a million sucker-rod pumps are installed in oil wells in the U. S. alone. In Venezuela, too, the system is widely used; some 5,000, or 90 percent, of Cia. Shell de Venezuela's wells produce a total of 400,000 BOPD by this method. Most of the crude pumped is viscous, gassy and contains relatively small amounts of free water. API gravities vary from 90 to 16O; dead oil viscosities vary from 10 to 10,000 cp at the pump; and GOR's range from 100 to 2,000 cu ft/bbl. Pumps are set at depths ranging from a few hundred to 6,000 ft; the average setting depth is about 2,500 ft. From the literature, it appears that although recent years have seen significant progress toward understanding the rod pumping system as a whole, relatively little attention has been paid to those key items, the sucker-rod pump and the subsurface gas separator or gas anchor. Perhaps because of proration in the U. S., pump manufacturers have seemingly concerned themselves more with the durability of their product, achieved mainly through robust design and metallurgical know-how, than with its working efficiency. In 1963, CSV commenced a major rehabilitation and expansion of its heavy oil fields along the Bolivar Coast. The advent of the more efficient gravel-packed completion and of large-scale thermal recovery (mainly steam soak) operations resulted in well potentials *Now with B. I. P. M., The Hague, The Netherlands. greater than pump capacities. Hence, an urgent need arose to improve over-all pump efficiencies and to attack those special problems related to the production of both the extremely viscous and the hot, steam-laden crudes that formed an increasing proportion of the total stream. There followed a detailed investigation and testing program, carried out in close cooperation with a major pump manufacturer. This culminated in the introduction to the oil industry of a new line of sucker-rod pumps. Early Investigations and Experiments Field Tests Extensive field tests were carried out in three primary Bolivar Coast wells with an in-situ dead oil viscosity ranging from 400 to 6,000 cp. In these installations provision was made to (1) monitor bottom-hole pressures below, in and above the pump by means of pressure transducers, and record casing- and tubing-head pressures continuously; (2) measure accurately the annulus gas, as well as measure the tubing gas and liquid production from the well; (3) take special PVT samples of the well fluid; (4) measure power consumption of the prime mover; and (5) measure the rod loads at the polished rod. A typical test installation is illustrated in Fig. 1. It was established from the pressure transducers that with viscous oils, there is considerable flow resistance across the pump and gas anchor assembly. Pressure surges were observed over each pump cycle,

Jan 1, 1970

By Nicholas R. Dixon

This report summarizes all work performed under Phases I, II and III of U.S. Bureau of Mines Contract H0387006, "Development of a Prototype Retrofit Noise Control Treatment for Jumbo Drills." The noise and vibration levels of four jumbo drills were characterized and a survey of percussive rock drill usage is reported. A Gardner-Denver DH 123 drill was chosen as a demonstration drill, and extensive noise diagnostic studies were performed. Noise control treatments were designed, developed and evaluated in a reverberant drill test facility. The treatments consisted of an integral enclosure/muffler for the drifter, vibration isolation of the drifter from the enclosure and feed, and a drill steel sheath. A 19 dBA reduction in overall sound power level was achieved with no loss in drilling rate. The prototype retrofit treatments were field tested in an aboveground mine and in a production section of an underground zinc mine. Long-term durability and operator acceptance of the enclosure/muffler treatment were excellent. Preliminary evaluation of the drill steel sheath was encouraging, although additional testing is required.

Jan 1, 1982

By Lawrence H. Roth

Past failures of coal refuse embankments have resulted in more intensified efforts in inspections of coal refuse sites. Inspections, however, are mainly qualitative and time consuming. In August 1975 CH2M HILL was awarded a contract to identify, develop, and test a rapid system for monitoring coal refuse embankments to aid in inspections. The rapid monitoring system developed uses convergent and vertical photography from conventional fixed-wing aircraft. The system was tested on an active landslide and on two coal refuse facilities using both black and white and color infrared film. Field tests showed the system was capable of accurate measurement while providing qualitative data through photointerpretation. The accuracy of the system allows it to be used to monitor coal refuse embankments, tailings dams, major earth dams, and natural slopes. Bibliographies of literature reviews in the area of past coal refuse embankment failures, monitoring instruments and methods, and photogrammetry are included.

Jan 1, 1977

By T Salles, G Duclaux, E R. Ramanaidou

In a continental environment, sediment mobilisation, dispersion and deposition are mainly controlled by mass gravity and streamflow processes. Alluvial sedimentary systems have an important economic value because of their capacity to host mineral resources. In the Hamersley Province, alluvial iron deposits (including the well-known detrital iron deposits and channel iron deposits) play an increasing role on the commodity market. Alluvial deposits exploration is challenging and generally involves geomorphologic and stratigraphic field studies, as well as expensive exploratory surface sampling and drilling. We applied a new surface processes modelling technique to investigate iron rich material, ie the erosion product of bedded iron formations -dispersion in the Hamersley Province. LECODE is a 3D-parallel surface processes forward modelling code designed to compute surface flow and solve erosion, transport and sedimentation on the geological time scale. The code offers new quantitative ways to better understand how sedimentary deposits develop in intra-continental and channel environments. Here we show that our integrated forward model is capable of opening a window to the construction of sedimentary architectures, including facies distribution, deposit thickness and development of heterogeneities such as mineral traps over the modelled domain. The model results represent 1 Ma of surface evolution and are validated through comparison to published paleovalleys map and known occurrences of iron ore deposits. This numerical modelling approach allows for the first time to track alluvial materials from source to sink through time, test existing geological models and faithfully reproduce the first order distribution of alluvial iron deposits in an area of interest. This work strongly suggests the presence of iron rich alluvial deposits reserves under cover, in unexplored detrital fans in the Fortescue Valley. This method, potentially coupled with sediment geochemistry and basin analyses studies, has the potential to maximise alluvial iron deposits exploration success, while reducing exploration cost and associated environmental impact.CITATION:Duclaux, G, Salles, T and Ramanaidou, E R, 2013. Alluvial iron deposits exploration using surface processes modelling - a case study in the Hamersley Province (Western Australia), in Proceedings Iron Ore 2013 , pp 75-80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

In the latter half of 1973 a contract was given to Roberts-Holland Joint Venture for the stripping of the southern exhaust airway.The contract was carried out efficiently and relatively cheaply. It was completed 2 months ahead of schedule.The sinking stage and in particular the drilling jumbo proved to be a success and helped produce an above schedule stripping rate.No major problems were encountered with ground conditions or ventilation. A survey of the shaft showed the diameter to be within the set limits of 5·49 m ± 0·15 m.

Jan 1, 1974

The ore treatment expansion programme at Mount Isa Mines required the erection of a new lead-zinc concentrator to be known as No. 2 Concentrator. This concentrator was designed by Western-Knapp Engineering Company in conjunction with staff of Mount Isa Mines Limited. Metallurgical design followed conventional wet milling practice, but the size of many plant units is larger than previously used at Mount Isa. The. total capacity of the new plant is 150,000 tons per four weekly period, and the plant is designed to operate in two equal parallel sections.Erection was contracted on a turnkey basis, and the plant was commissioned as a production unit on 23rd June 1966.The existing concentrator, No. I, was converted to treat all copper ore, and the total capacity of the two plants is now 390,000 tons per four weekly period.

Jan 1, 1968

By Melvin I. Esrig

Lime Cement column stabilization of soft clay and sand in Salt Lake City, Utah and in San Francisco California is described and discussed. Stabilization permitted the construction, in a single stage, of a 14 m MSE wall on "medium" clay in Salt Lake City. It was used to mitigate the potential for liquefaction in San Francisco and to stabilize the Young Bay Mud beneath the BART extension to San Francisco Airport. These applications are described and the field measurements of performance are reported.

Jan 1, 2000

By E. Rupprecht, J. Volkwein, K. Cashdollar, R. Gürtunca

The National Institute for Occupational Safety and Health (NIOSH) mining research program at the Pittsburgh Research Laboratory (PRL), includes the areas of coal mine dust control and monitoring, and explosion prevention. One very important project at PRL is development of a continuous recording person-wearable respirable dust monitor. This Personal Dust Monitor (PDM) is a respirable dust sampler and gravimetric -equivalent analysis instrument that is part of a belt-worn mine cap lamp battery unit. Prototypes were successfully tested in the laboratory and in four underground coal mines. The PDM testing demonstrated that it was convenient to wear and use, robust, and provided accurate and timely data. NOSH is also conducting research in the program area of coal mine explosion prevention, suppression, and mitigation. Aspects of this research program include: full scale explosion research, laboratory scale research, frictional ignition of methane, mine ventilation seal construction, prediction of coal mine methane emissions, mine monitoring systems, flame cutting and welding operations, spontaneous combustion, and emergency preparedness.

By A. J. Hendron, J. E. Monsees

INTRODUCTION This paper is the outgrowth of work done by the authors to prepare the seismic design criteria for underground structures on the Southern California Rapid Transit District (SCRTD) Metro Rail Project. It is a follow-on to a similar paper presented at the October, 1984, ASCE National Convention (17). For design, the earthquake-induced distortions recommended herein are to be added to the normal static loading conditions for the underground structure. This design approach has been used by 18 section designers on the SCRTD Project. Preliminary results from two- and three-dimensional finite element solutions have partially verified the approach. Areas where additional research is needed for special cases are identified. EFFECTS OF EARTHQUAKE The effects of earthquakes on underground structures may be broadly grouped into two general classes -shaking and faulting. In response to earthquake motion of bedrock (shaking) , the soil transmits energy by waves. Seismologists identify various types of earthquake waves, but underground engineers are generally interested in the effects of transverse shear waves which produce a displacement of the ground transverse to the axis of wave propagation. The orientation of propagation is generally random with respect to any specific structure. Waves

Jan 1, 1985

By K H. Esbensen, K Engström

The conclusion from the debate over the last decade in the mining sector is that, for grade control, reverse circulation (RC) drill sampling gives more reliable results due to less sampling problems than blasthole samples. However, by conducting the latter with well-controlled procedures there still exist fair possibilities to counteract the major blasthole sampling problems and achieve fit-for-purpose representativeness, especially if based on minimal loss of fines. In the present PhD study, extensive replicate experiments and variographic characterisations are conducted to evaluate the performance of manual blasthole (BH) sampling and sectorial segment sampling. The experiments were performed in Luossavaara-Kiirunavaara AB (LKAB)’s Leveäniemi open pit mine in the north of Sweden. The experimental area is an apatite-magnetite iron ore deposit of the Kiruna type, with the demand to exhibit a maximum of local heterogeneity to allow the experiment the largest possible conclusion powers. Gathering and splitting the complete BH drill cutting cones (fines cone, coarse cone) served as an authoritative reference on which to assess the representativity of the two BH sampling methods.Results show that manual BH drill sampling is able to produce samples with an acceptable accuracy and precision if performed properly and with insight. Based on variographic comparison, segment sampling shows similar precision for chemical grades as the manual sampling, while the particle size distributions were more deviating for segment sampling than for manual sampling at the high and low size ranges. Possible reasons for these partly surprising results are discussed.For further investigation of the performance of BH versus RC drill sampling, a second experiment has been planned on a parallel profile. This will result in an unprecedented opportunity for a full variographic comparison between RC and BH sampling, aimed at designing specific, fit-for-purpose sampling procedures as a function of ore quality, cut-off grades and important contaminant levels.CITATION:Engström, K and Esbensen, K H, 2017. Blasthole sampling (replicate and variographic experiments) in LKAB open pit iron ore mines – fit-for-purpose representativity?, Australia, in Proceedings Eighth World Conference on Sampling and Blending , pp 85–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By S. P. Singh

Drifts are an integral component of underground mining. They provide access for men and material, means for transporting ore and rock and serve as air passageways. In view of their importance on the overall safety, economy and productivity of mines, empirical guidelines for controlled blasting design in drifts have been developed in this study. The application of the proposed concept was described by generating blast hole patterns for a mine with the help of a computer program. The mechanism of blast damage and the need for controlled blasting to alleviate ground control problems in underground mines have been outlined in this paper. The economic analysis between normal-and controlled blasting was performed based on the information from an operating mine. In addition, the review of drift blasting practices and problems in Canadian mines was also carried out in this study.

Jan 1, 1990

By P. Venkatraman

Laboratory and pilot-scale test data have shown that the innovative feed presentation of the CrossFlow separator provides improved metallurgy when compared to traditional hindered-bed or teeter-bed classifiers. This design feature prevents excess water from entering the separation chamber and disrupting the overall fluidization flow rate within the teeter zone. Recent side-by-side industrial-scale evaluations have verified that this technology can improve overall efficiency, reduce the cut point of separation, and increase throughput capacity. This paper describes the important features that make this novel separator ideally suited for size classification and density concentration. Test data from heavy mineral, phosphate, and industrial mineral applications are also discussed.

Jan 1, 2005

By H. R. Beard

The Federal Bureau of Mines investigated the absorption of radium and thorium from waste uranium leach liquor by clays and other materials. This work was conducted in support of the Bureau's goal of minimizing the environ¬mental conflicts, impacts, and occupational hazards Associated with mining and mineral processing operations. Tailings and soil samples from Wyoming and Utah were contacted with tailings liquors to determine the degree of absorp¬tion. Absorption ranged from 0 to 99 percent for radium and from 0 to 31 per¬cent for thorium. Some samples, which readily absorbed radium, were contacted with various salt solutions that could be present in tailings solutions to determine their effectiveness as desorbents. The desorption of radium ranged from 0.06 to 100 percent. An alpha-spectrometric method was used to determine the radium and thorium, concentrations in the solutions and the solids.

Jan 1, 1979

A rotating disc of precipitant zinc in a single stage flow reactor was used to study the effects of deposit mass on the reaction kinetics of copper cementing on to zinc from dilute aqueous solutions.The reaction rate is controlled by external mass transport and the mass transfer coefficient (relative to the original precipitant area) is dependent on the quantity of deposit present. For deposit masses up to about 0·3 mg/cm2 the mass transfer coefficient (first order rate constant) is that expected for the counter-diffusion of reactant and product cations through a laminar boundary layer to a smooth rotating disc. For depositmasses from 0·3 mg/cm2 to about 5 mg/cm2, the mass transfer coefficient increases significantly with deposit mass. For deposit masses greater than 5 mg/cm2 and at least up to 12 mg/cm2, the mass transfer coefficient has again a constant value which is some four to seven times the initial ("deposit free") value. The rate constant for the entire range of deposit masses studied (0 to 12 mg/cm2 ) can be expressed empirically as a cumulative normal distribution of the logarithm of the deposit mass.The enhancement in the mass transfer coefficient for deposit masses greater than 5 mg/cm2 relative to the initial mass transfer coefficient depends on the local operating conditions and increases with increasing disc rotational speed. This enhancement is, however, independent of the previous history of reaction rates.

Jan 1, 1973

By N. A. D. Parlee, M. M. A. El-Naggar, G. 8. Horsley

The apparatus was of a modified Sieverts type1&apos;2 with a reaction tube designed to function also as the cell component of an oxygen pressure gage. The reaction tube assembly is shown in Fig. 1 and described in Table I. The main body is a 1-in.-OD 15 mol pct calcia-stabilized zirconia tube. The ground-glass joint, g, the male part of which carried a prism for optical pyrometer use, was connected to the remainder of the Sieverts apparatus. The calibration of the cell (at its 1000°K operating temperature) for internal oxygen pressures (PO2in) in the range 0.2 to 10 9 atm was made against internal air pressures measured by mercury manometer and McLeod gage. At very low po2in values down to l<Tn atm the performance was checked by comparing pQ calculated from electromotive force measurement when the apparatus was filled with a) pure CO gas and b) a CO-CO2 mixture of the ratio CO-CO2 = 1:0.398, with Po, values calculated from the equilibrium constants of the following reactions at 1000°K:

Jan 1, 1968

By E Rojas, C Pardo

The exploitation of primary ores using cave mining caused new challenges at the El Teniente mine that required changes to a number of conventional cave mining practices. For example, in the 1970s and 1980s, panel caving was introduced to manage certain geotechnical and operational conditions. Today, El Teniente mine is facing new challenges associated with deep cave mining and establishing its New Mine Level (NML) project, which is located 240 m below the Esmeralda operating cave.The engineering and development phases for this new project have been largely based on experience and lessons learned throughout the history of primary ore exploitation at El Teniente mine, particularly knowledge about seismicity control, the management of collapses and operational practices. For example, previous experience demonstrated that seismicity could be managed by preconditioning using large-scale hydraulic fracturing (HF). HF has been systematically applied in the column of ore above the undercut planned for the NML project and below the production or extraction level, where the main ventilation and haulage infrastructure are to be located.This paper discusses how this has been achieved and is based on previous experience of preconditioning using HF, which has been applied in the selection and management of exploitation techniques and associated planning strategies and design parameters for the NML project.CITATION:Pardo, C and Rojas, E, 2016. Selection of exploitation method based on the experience of hydraulic fracture techniques at the El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 97–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Matthew A. Perras

With growing populations, infrastructure projects are utilizing underground space to expand transportation networks, water supply and sewer disposal systems and hydropower facilities. These new projects require large diameter tunnels to meet the growing demands. As the tunnel diameter increases, not all rock mass properties are scalable and precedent experience becomes less reliable. One such non-scaleable property is lamination thickness. Numerical modelling was conducted to determine the influence of lamination thicknesses on a 16 m diameter tunnel. Five different areas of excavation response were found to exist for laminations ranging between 0.16 to 16 metres in thickness. For this tunnel diameter, critical lamination thicknesses of 6 metre and 1 metre were found to exist. Above 6 metres the excavation response was similar to isotropic models. Below 6 metres the stresses and yield are channeled by the lamination boundaries, increasing plastic deformation. Below 1m multiple lamination units become unstable and the displacements increase significantly and the shape and extent of the yield zone size changes dramatically. The yield zone is controlled by bed deflections and bed parallel shear. As the lamination thickness decreases tensile failure first begins in the haunch area and progressively extends above the crown until a self-limiting plastic yield zone shape is reach at lamination thicknesses below 0.4 metres. Conclusions drawn from observations at the Niagara Tunnel Project are those of the authors.

May 1, 2009