Search Documents

By Joel Darmstadter

The position of the coal industry in America’s fuel and power picture remains one of prime importance. Measured in Btu terms, the industry is the country’s leading energy producer and an important exporter. Foreign coal sales yield annual proceeds of about $4 billion. Coal’s one-fifth share of the nation’s energy consumption is nearly as high as that of natural gas. Coal is the electric utility sector’s principal fuel supplier. It accounts for about55% of the electricity generated at power stations.

Jan 1, 1999

By B Hartmann

In 2003, Independence Group NL purchased the Long Shaft Nickel Mine complex (Long) in Kambalda, Western Australia. Lightning Nickel, the nickel operating arm of Independence Group, faced considerable challenges operating the mine, with the most significant challenge being able to prove that the remnant ore at Long and the associated orebodies could be mined safely and efficiently. Given the seismic history at Long, the magnitude of these challenges could not be underestimated. In an effort to achieve 100 per cent extraction of the flatter orebodies, traditional methods such as room and pillar were dismissed. A method consisting of transverse sills, butting into each other was proposed. To stop fill material from the first sill rilling into the adjoining sill, it was proposed to backfill the sills with pumped cement fill. The capital cost of the fill plant was estimated to be in excess of $1.5 million and the cost for cement alone was $1.0 million per annum. Shotcrete was already an extremely useful tool in dealing with the widely variable stress environment, but was to be used in an innovative manner that would enable the full extraction of a tabular section of the Victor South orebody. A layer of shotcrete, approximately 100 mm thick, was to be sprayed on the up dip wall of the initial development sill. The sill was to be backfilled with ænormalÆ development waste and ætoppedÆ with sand backfill. The next sill, ie slightly up dip and alongside, was to be mined along the shotcrete boundary wall. With respect to wall stability, the premise was that the shotcrete wall would stay in place and prevent the backfill (development waste and sand) from rilling into the adjoining development. It was also proposed that any breaches of the shotcrete wall would be repaired using shotcrete before substantial inflow of backfill into the ænewÆ development. This paper describes the development and implementation of this mining method, as well as some of the associated financial aspects.

Jan 1, 2008

IT has often been stated in the past that the materials known as inert fillers were merely adulterants nsed in the manufacture of paint, and that their purpose was to cheapen paints made from more expensive pigments, such as zinc oxide or white lead. In recent years, however, practical tests in various parts of the world have proved that many of the inert fillers, when used with wisdom, possess very definite and advantageous properties.Another oft-repeated statement which had a far-reaching effect in the past, and which is not without influence to-day, is that the very best paint must always be made from a pure pigment, without admixture with either a fellow pigment or an inert filler. Both or either of these statements may be true in a few isolated instances, but for the vast majority of ordinary painting conditions there is an abundance of experimental evidence to prove that neither is true.With the desire to further investigate these points and po 'determine the best combination of pigments and fillers for use as an outside white paint on plant buildings, a number of panels were prepared in the laboratory of this company.

Jan 1, 1924

By Amy B. Cerato

The application of this study is to use helical anchors as a foundation system for small wind tower (1 ? 10 kW) guyed cables. Helical anchors are currently used to anchor guyed cables of telecommunication and electric towers. However, the increased dynamic vibrations a wind turbine adds to the tower and foundation system under working loads, as well as extreme environmental conditions (e.g., straight line winds, ice load or sudden furling shocks), require additional knowledge about the behavior of helical anchors. These field conditions were simulated in this study by instrumenting a working tower with load cells and 3-axis accelerometers to gather data on wind speed and tower response. These tower responses were then transmitted to the helical anchors through an extensive, large-scale testing program that included monitoring the performance of the helical anchor foundation under dynamic loads, subject to natural variations in both wind regimes, precipitation (water level) and variations in helical anchor geometry. This paper specifically discusses the effects of helical anchor geometry on helical anchor performance under long-term dynamic loads.

Jan 1, 2008

By J. Stacho, Frankovská. J.

"Abstract The use of continuous flight auger (CFA) piles in Slovakia has increased significantly in recent decades. High-rise building of administrative centre Lakeside Park in Bratislava is based on piled-raft foundation. The technology of CFA has been used due to the advantages of this technology in comparison with driven and bored piles in local geotechnical conditions. Piles have been designed in accordance with Eurocode 7. Resistance of piles was calculated by using an analytical calculation model for bored piles according to Slovak technical standard and CFA technology has been taken into account by coefficient equal to 1.1. Settlement of piles was calculated by using a calculation model which is being used in Czech Republic and Slovakia. Two well instrumented static load tests were carried out to verify the pile design. The results of static load tests showed that the design was conservative. The paper presents analysis of numerical modelling of CFA pile and static load tests. Load-settlement curves and load distribution curves over pile shafts are compared. Software Plaxis 2011 has been used for numerical modelling. Hardening soil model allows considering over consolidation of Tertiary Silts and water pressure in deep sandy lenses. The article also presents the parametric study where the influences of pile-soil interface reduction factor, over consolidation ratio and material models of soils are analysed. The results of numerical modelling showed that the most appropriate results have been obtained when the interface reduction factor equal 0.9 and real behaviour of groundwater were considered. The conclusion of the paper confirms that mechanical behaviour of the ground can be better understood and determined by using FEM than analytical methods.1. IntroductionPiles are among the most frequently used elements of deep foundations. Piles transfer loads down to a suitable bearing stratum when the soil immediately below a construction is unsuitable. Piles are also used to reduce settlement of structure. At present, the requirements of limit settlement of structures are more stringent. Examples of these structures are commercial and administrative centres that form a complex of different tall buildings. High-rise buildings cause greater contact stresses than connected low-rise buildings. Pile foundations in such cases should be placed under the high-rise buildings to achieve an appropriate settlement.Resistance of piles can be determined from static load test results, in-situ tests and empirical experiences or calculations. Static load tests give the most reliable results, but these tests are also the most expensive. This is the reason for constant development of computational methods. Especially numerical methods give more accurate results by using more sophisticated material models e. g. hardening soil or hypoplastic model."

Jan 1, 2014

By Aki Fujii, Hiroshi Dobashi, Mitsuro Matsuda, Yoshinari Kondo

INTRODUCTION The Metropolitan Expressway Central Circular Route with a total length of approximately 47 km is located outside the Inner Circular Route of Tokyo (at a radius of approximately 8 km from the city center). Sections with a length of approximately26 km, slightly less than 60% of the total length, on the east and north sides are in ser-vice. Completing the Central Circular Route (Figure 1) is expected to enable through traffic concentrated at the city center to get around, and to form a well balanced trans-port network, which will alleviate traffic congestion considerably. The Central Circular Shinjuku Route, a section with a length of approximately 11 km on the west side, is now being constructed at a fast pace. The route is being built mainly by the shield tunneling method to carry out work smoothly under a trunk highway carrying heavy traffic and to reduce adverse effects of tunneling work on residents in the neighborhood. Shield tunnels have recently been becoming longer and deeper, and no secondary linings have been used in an increasing number of cases because of the over-crowding of cities or the reduction of budgets for public works. Economical, durable and high-quality segments have been required for linings of shield tunnels. Segments are made of concrete, steel, cast iron or combination thereof. Concrete segments are generally used in shield tunnels of medium to large diameter. Concrete segments are highly durable and resistant to compression, so they are highly resistant to earth pres-sure, water pressure and jack thrust. They are, however, heavy and have low tensile strength, so they are brittle and their corners are likely to spall. Concrete segments should therefore be handled carefully.[1] The authors have developed a steel fiber reinforced highly flowable concrete segment (referred as SFRC segment) that overcomes the weaknesses of concrete segments[2] to construct economical, durable and high-quality linings. SFRC segments have been applied to outbound sections SJ51 through SJ53 of the Central Circular Shinjuku Route. Unlike conventional concrete segments (referred as conventional RC segments), SFRC segments are made of steel fiber reinforced self-compacting highly flowable concrete. SFRC segments require less reinforcing bars than conventional RC segments because steel fibers are expected to work as reinforcements. Steel fiber reinforced concrete is a composite material that overcomes the brittleness of plain concrete, and has higher resistance to bending, tension and shear than

Jan 1, 2007

By Whiten W. J

A simulation model was used to study the performance of various types of screen cloth on industrial vibrating screens. The model takes into account the effect of loading upon screen performance and predicts both themass flow rate and size distribution of the screen products.It was found that the use of the simulation model allowed the reconstruction of data for identical conditions and hence has simplified the analysis of the comparative performance of the screens. The dependence of performance upon operating conditions was found to vary markedly with screen cloth type.

Jan 1, 1977

By V. Pawlowsky-Glahn, E. Pardo-Igúzquiza, J. J. Egozcue, R. A. Olea

Compositional data constitutes a special class of quantitative measurements involving parts of a whole. The sample space has an algebraic-geometric structure different from that of real-valued data. A subcomposition is a subset of all possible parts. When compositional data values include geographical locations, they are also regionalized variables. In the Earth sciences, geochemical analyses are a common form of regionalized compositional data. Ordinarily, there are measurements only at data locations. Geostatistics has proven to be the standard for spatial estimation of regionalized variables but, in general, the compositional character of the geochemical data has been ignored. This paper presents in detail an application of cokriging for the modelling of compositional data using a method that is consistent with the compositional character of the data. The uncertainty is evaluated by a Monte Carlo procedure. The method is illustrated for the contents of arsenic and iron in groundwaters in Bangladesh, which have the peculiarity of being measured in milligrams per litre, units for which the sum of all parts does not add to a constant. Practical results include maps of estimates of the geochemical elements in the original concentration units, as well as measures of uncertainty, such as the probability that the concentration may exceed a given threshold. Results indicate that probabilities of exceedance in previous studies of the same data are too low.

Jan 1, 2015

By J. A. McLennan

Nickel laterite deposits are typically formed from tropically weathered mafic-ultramafic complexes. The resulting nickel concentration is found within soil horizons and is mineable with regular dozer units. At the time of mining, digging elevations are needed at selective mining units (SMUs). Moreover, for mine planning, the costs due to dilution and lost ore require mining elevations to be specified. A conditional simulation approach is used to calculate ?optimum? SMU mining elevations. Multiple realizations of the ore base surface are simulated. For a single bottom surface realization, dilution and lost ore costs are calculated over the entire vertical extent of each SMU. The optimum mining elevation is the elevation where the lowest summed cost of ?accepting dilution? and ?wasting ore? occurs. The reported SMU dilution is the cost of mining the volume of waste located below the bottom surface and above the optimum mining elevation and the reported SMU lost ore is the cost of not mining the volume of ore above the bottom surface and below the optimum mining elevation. For all ore bottom surface realizations, optimum SMU mining elevations and their associated dilution and lost ore costs are calculated and compiled to represent production uncertainty.

Apr 1, 2005

By P. D. White, J. T. Moss, J. S. McNiel

Results of experimental work on the in situ combustion process were first published in this country in 1953' when Kuhn and Koch described results of a three-well test in Jefferson County, Okla. Shortly there-after Grant and Szasz2 described field studies in Nowata County, Okla., in which several modifications of the basic combustion process were investigated by injection of various oxidizing gas mixtures other than air. In the past five years speculation concerning this method of oil recovery has continued, with a number of interesting papers on various aspects of in situ combustion appearing in the literature3,4,5,6,7. However, only one of these' provided actual engineering information on pattern-type field experiments. The primary objectives of the Oklahoma three-well test were to check operation of specially designed electrical ignition equipment and evaluate problems associated with initiation of combustion in a natural oil sand reservoir. Immediately following successful completion of this test in the Pontotoc sand, plans were activated for a second field experiment to be conducted in the same sand a short distance away. The objective of this second field test1 as to establish a relationship between field observations and information derived from laboratory experimentation and computations. Secondary objectives of the test were to develop operating tech- niques and define operating problems, and to obtain information that would assist in the economic and engineering appraisals of the process. Careful planning was required since this test was designed with the hope of providing basic information on the characteristics and operation of a combustion drive. It was necessary to include test facilities which would not only permit precise control and measurement of the process variables but would also provide sufficient flexibility of control to insure that variables in the combustion process could be studied during the course of the test under a wide range of conditions. In order to accomplish these objectives elaborate instrumentation and several control wells were included in the design of the test installation. This type installation was felt to be well suited for an experimental study, but was in no respect intended as a counterpart of a commercial-scale operation. PRELIMINARY LABORATORY WORK An important objective of the field experiment, as stated previously, has been to obtain reliable data on operating variables which might be compared with similar data obtained in laboratory combustion tests. The value of successful correlations between quantities that can be measured in the laboratory and those obtained in a full-scale commercial venture has been well established for other industrial processes. The difficulty of following a process underground should make such correlations even more essential here. Also. approaching the field test phase of development of in situ combustion, it was considered desirable to precede design of test equipment with laboratory combustion studies under a variety of conditions to establish likely ranges of variables. These included temperature, air injection rate, frontal advance rate and produced gas composition.

By P. Falcão Neves

A detailed analysis of the geomechanical behaviour in rock cutting with a diamond saw is provided to obtain a better understanding of the mechanisms involved in the process. The energy of elastic deformation (before failure) and plastic deformation (post failure) was determined in uniaxial compression tests as well as the energy consumed per unit volume in the cutting process. The test samples are White and Ruivina marbles from Borba - Vila Viçosa in Portugal. Correlations between total deformation specific energy and cutting specific energy, normal and tangential forces and diamond indentation are analysed, and some conclusions are presented.

Jan 1, 2012

Engineering education has become a matter of national concern, at last, so I would like to talk about the links between the mining industry, the universities and technological developments. The Australasian mining industry and the mining schools have collaborated closely since the first school was established in 1871 and during those years there were a series of remarkable technological developments. For example:In the late 1880s George AndersoIl Richard developed chloride leaching of gold at Mt Morgan. This made a large difference to the wealth of Mt Morgan Mining Ltd.In the mid 1890s Robert Sticht demonstrated that pyrite smelting was an economically feasible process at Mt Lyell and the wealth which came to Mt Lyell Mining Co from his outstanding work made it one of the great companies in the country.During the first 15 years of this century flotation was developed at Broken Hill and it has proved to be one of the great technological inventions of this century.In the 1920s G K Williams started his outstanding work on lead smelting and refining at Port Pirie, this was work which ultimately re-wrote the text book on lead metallurgy and established Port Pirie as the mecca for lead metallurgists.In the 1920s also Frank Stillwell, later joined by Austin Edwards, established the new science of mineragraphy at the University of Melbourne. They were both great geologists, both were superb scientists and oddly enough both were outstanding athletes.In the 1930s Dr Ian Wark, a man in the front rank of Australian scientists of any period, started his outstanding work on flotation, work which resulted in a text book which remains a leader in its field today.In the 1930s also Arnold Black at Broken Hill South Ltd picked up the work which had been done at Mt Lyell many years previously and eventually wrote the papers on hydraulic fill which demonstrated that he led the world in fill technology. What a remarkable story of achievement it was, it laid the groundwork for the great industry we have today. It was possible because the industry was well supported by outstanding university schools and I would like to talk about some of these.

Jan 1, 1989

By Isaac Girón

Dado que se descubrieron grandes depósitos de fosfatos de Bayovar en Piura, se anunció la creación de la reserva subterránea de salmueras, donde sobresale el potasio, la sal común y el magnesio. Posteriormente, se relacionó la explotación de los fosfatos a la recuperación de sal y KCL. y la presencia de salmueras se convirtió en la única reserva de potasio del pais. En ese sentido, el presente texto describe la importancia del magnesio en dichas salmueras en tanto permite recuperar el magnesio a partir del proceso de evaporación y concentración. De forma que es posible la obtención de magnesio por el tratamiento térmico de los amargos y así fabricar el fosfato dicálcico mediante el proceso convencional, sin necesidad de usar el agua de mar.

Sep 13, 2001

By Thomas M. Barczak

With the development of the shield support, the primary requirement for successful ground control in longwall mining is to provide stable gate road and bleeder entries. Wood cribbing has been the dominant form of secondary support. However, the cost and limited availability of timber, along with the poor performance of softwood crib supports, has forced western U.S. mines to explore the utilization of other support systems. The recent success of cable bolts has engendered much interest from western operators. Several innovative freestanding support systems have been developed recently including: (1) "The Can"' support by Burrell Mining Products International, Inc., (2) Hercules and Link-N-Lock wood cribs and Propsetter by Strata Products (USA) Inc., (3) Variable Yielding Crib and Power Crib supports by Mountainland Support Systems, (4) the Confined Core Crib developed by Southern Utah Fuels Corporation; and (5) the MEGA prop by MBK Hydraulik. This paper assesses design considerations and compares the performance and application of these alternative secondary support systems.

Jan 1, 1996

By María Julia Ubillús Mellet

El presente texto complementa el estudio de las estrategias de seguridad en las empresas mineras a través de la alienación de las herramientas de gestión humana en una cultura de seguridad y prevención competitiva, de forma que se mejore el estilo de gestión en seguridad de los equipos gerenciales en las empresas mineras, y se desarrolle un manejo adecuado y responsable entre el área gestión humana y cultura organizacional. En ese sentido, la excelencia de gestión en seguridad radica en que el elemento humano se conecte de forma sistemática a las estrategías que la organización plantee.

Sep 12, 2005

Several years ago, Hudco Industrial Products began experimenting with the idea of levitating a conveyor belt with a film of air, much like the puck on an air-hockey table. While conducting its research, the company found out that some Russian and Dutch companies attempted the concept during the 1970s. After studying those conveyors, Hudco determined that its design was better. The Hudco advanced air-supported conveyor consists of an air-tight plenum, or chamber, that runs the length of the belt. The topside of the plenum has a formed trough. It corresponds to the profile of conventional troughing rollers. Low-pressure air is provided to the sealed plenum from a low horsepower blower. This pressurized air is metered and released through the central portion of the trough and reacts against the underside of the belt. The differential pressure between the top and bottom surfaces creates the lift to support the loaded belt. Airtight covers are installed to seal the transported materials in the plenum trough.

Jan 1, 2002

By X. Bai

A new heuristic sublevel mining stope optimizer is presented. The optimizer seeks the best locations and lengths of a series of vertical raises that, together with the blocks linked to each raise, define a mining stope. Five design constraints ? the footwall angle, the hangingwall angle, the number of raises, the maximum distance of a block from a raise, and the minimum width required to move the farthest block towards the raise ? allow the shape of the sub-stopes associated with each raise to be controlled. The optimization is done on the locations and lengths of raises using a genetic algorithm to efficiently sample the parameters? space. For each raise, a local network is defined in cylindrical coordinates around the raise such as to impose the design constraints. A maxflow algorithm on the local network is used to determine the optimal sub-stope for each raise. All substopes are combined to define the global stope for the entire deposit. The best global stope is obtained using a genetic algorithm to find the raise parameters providing the best profit over the entire deposit. Two synthetic cases and one real deposit are used to evaluate the new algorithm and compare the results with the single-raise optimizer. The multiple raises approach leads to significantly improved economics compared with the single-raise stope optimizer, and the dilution is also substantially reduced compared to the single-raise case.

Jan 1, 2014

By T Hughes

The Gekko InLine Pressure Jig (IPJ) was unleashed on the World gravity separation market in 1996 and has since sold over 150 units in applications including tin, diamonds, silver, coal, garnet and gold. During the past twelve years the knowledgebase of the best applications and capabilities of the IPJ has greatly increased. Improvements to the original IPJ design have included engineered ceramic ragging in specific gravities from 1.6 to 5.0, full automation and improved designs of feed presentation and tailings and concentrate handling systems. The IPJ has been found to be able to handle a wide feed size range and recover mineral at liberation size without significant addition of water to the mass balance. Test work carried out during full-scale operation of the IPJ has shown the IPJ can recover diamonds down to 0.5 mm, sulfides down to 0.3 mm and gold down to 0.1 mm which greatly expands its application in the mineral processing industry. A significant volume of data now supports the symbiotic benefits of an IPJ and flotation circuit combination to pre-concentrate an ore and minimise downstream processing requirements.

Jan 1, 2008

By F. F. Peng

The raw-coal feeding system and the upward medium current flow in a dense-medium vessel (DMV) are, in addition to the residence time of particles in the separator, important factors for efficient coarse particle separation. The feed material from a raw coal screen and/or pre-wet screen merge with the major volume of circulating medium as push medium, guided by an adjustable submergence baffle plate deep fed into the separator for effective separation. The remaining volume of the circulating medium enters from the purge and drain hoppers at the bottom of the DMV. This generates a gentle upward medium current flow in the separator, which prevents dense medium stratification/settling and merges as part of the push medium. A two-dimensional, two-phase model developed using computational fluid dynamics (CFD) is used to describe the flow pattern and evaluate the function of the dip plate for understanding the mechanisms of particle separation in the separator. The particle movement in the DMV is also tracked to investigate the major operating parameters affecting the separation performance of the DMV. The simulation results of the DMV separation performance are validated by in-plant test data.

Jan 1, 2007

The largest investment in mining equipment in Caterpillar?s history ? The F series mechanical and electrical drive trucks ? is rapidly advancing. Caterpillar showcased the 793F and 797F mechanical drive trucks and the 795F ac electric drive truck at MinExpo in 2008 and have continued testing since then. The 793F and the 797F have accumulated more than 75,000 hours of field testing and have proven their performance capabilities and their durability. The new Cat C175 engine that powers them has racked up 130,000 hours of field testing in mining trucks and more than 120,000 hours in power systems. Because of the success of these field-follow programs, the 793F is targeted to go into full production within a few months and the 797F late this year. Caterpillar engineers have been testing two 795F ac prototypes at the Tucson Proving Grounds in Arizona. The development program has provided input for the construction of a new 795F ac in Decatur, IL. The new truck recently shipped to a copper mine in North America where it will serve as the first field-follow 795F ac as it works at the mine. The 313-t- (345-st-) capacity 795F ac will enter a new size class for Caterpillar, and, as a result, the primary focus of the Caterpillar ac electric program has been on the 795F ac. The commercial launch date will be defined as the field-follow program progresses. ?It?s fitting that soon after producing the 50,000th Cat off-highway truck, we are now shipping our first ultra-class ac electric drive truck to a mine,? said Chris Curfman, president of Caterpillar Global Mining. ?Our new trucks further solidify our position as the one manufacturer to provide unparalleled options and unmatched customer support.?

Jan 1, 2009