Search Documents

By J. H. Zietsman, M. W. Erwee, P. J. A. Bezuidenhout, Q. G. Reynolds

"Pyrometallurgical furnaces are tapped through tap-holes that are opened with drills and oxygen lances. The lance is often used on its own or as the last step of opening the tap-hole. Interaction of oxygen with molten material inside the tap-hole can occur, and is a phenomenon that is not well understood. As part of a study that focuses on the effect of lancing on flow inside and around the furnace tap-hole, a cold-model validation was done. The validation study focuses on validating the MULTIPHASEINTERFOAM multiphase flow solver in OpenFOAM® for the problem involved. The sensitivity of the model to different materials properties (viscosity and density in particular) is presented with both cold models and the results from flow simulations in OpenFOAM®. IntroductionMany pyrometallurgical operations are carried out in furnaces where molten material accumulates continuously. Once enough material has accumulated and is ready to be removed from the furnace, material is tapped through one or more tap-holes in the furnace. Tap-holes differ significantly in both geometry and materials of construction, depending on the process involved – examples of different types of tap-hole configurations can be found in, for example, Nelson and Hundermark (2014). Tapholes all share one common feature: they are high, wear areas of the furnace. Molten material at high temperature flows through these areas, after which the tap-hole is sealed, usually using tap-hole clay. The purpose of the tap-hole clay is to harden inside the tap-hole and seal it until the next tap.Once ready to tap, a pneumatic drill and/or oxygen lance is used to open the tap-hole. The extent of lancing a furnace tap-hole depends strongly on the type of furnace. In, for example, many blast furnace operations lancing is limited as much as possible, and done only if drilling was not effective. In other operations, such as on small-scale pilot furnaces with short tap-holes, only lancing is used to open the tap-hole."

Jun 1, 2019

By Caroline B. Chapleau, Mélanie Proulx, Claude Bazin, Gaétan Lavoie

"Quebec Cartier Mining operates a pelletizing plant in Port-Cartier, QC. Grinding, agglomeration and pellets induration are the three main steps in the preparation of iron oxide pellets. In 1998, following different recommendations, the company increased the speed of one of its ball mill in order to increase the grinding efficiency of the machine. As expected, the increased speed lead to an increase of the power draught, which did not produce the expected increase of fineness of grind, neither its allows to increase the mill throughput. The change of behaviour of the mill could hardly be understood by comparison of discharge size distribution at initial and modified mill rotation speed. On the other hand, the use of the selection function from a population balance model provides an insight of the changes that occurred in the mill. This paper reviews the various steps required for the estimation of a grinding mill selection function. Results of the calibration to Quebec Cartier grinding mills show that the increase in the mill speed leads to higher rate of breakage of coarse particles, at the expenses of less efficient breakage of medium and fine size particles. In the case of the studied mill, breakage of coarse particles was probably not the critical step of the mill operation. INTRODUCTIONOre size reduction is the major energy consumption step in any mineral processing operations (Austin et al., 1984). Size reduction is required to either liberate valuable minerals from the gangue minerals in which they are imbedded, or to increase the specific surface of the ground material. Plant engineers continuously face the challenge to find grinding machines, operating conditions or grinding circuit flowsheet configurations that could improve the size reduction process at lower energy or m6dia consumption."

Jan 1, 2000

The Gippsland Basin, southeastern Australia, has an Upper Cainozoic history of episodic change of hydrology and the related environment, reflected in the geomorphology and surficial deposits of the onshore basin and the hydrodynamically controlled accumulations of petroleum of the offshore basin. Succeeding this episodic pattern, man through a number of activities, has had a sudden and major impact on the hydrology and the related environment. Activities include those directly affecting the groundwater system, such as extraction of fossil fuels with the consequent threat of land subsidence; irrigation and clearing of vegetation and the consequent effect of salinisation; change of land use and installation of septic tanks with resulting nitrate pollution; damming of streams and the consequent reduction in the frequency of floods with degradation of the biological Environment; de-snagging streams and construction of cutoffs with increased stream erosion, modifying wetlands including drainage, with the consequent degradation of their ecosystems; and increase in phosphate and nitrate inputs to the coastal lakes with the risk of their eutrophication.

Jan 1, 1992

The Subtropolis mine is a room-and-pillar mine extracting the Vanport Limestone near Petersburg, Ohio. In February 2018, mine management began implementing a heading reorientation to better control the negative effects of excessive levels of horizontal stress. The conditions in the headings improved, but as expected, stressrelated damage concentrated within crosscuts. The mine operator has worked to lessen the impact of the instabilities in the outby crosscuts by implementing several engineering controls. With the implementation of each control, conditions were monitored and analyzed using observational and measurement techniques including three-dimensional (3-D) LiDAR surveys.

Jan 7, 2020

By E. W. Thorton

"This paper is intended to show that grinding media can effect flotation results, and in some instances the results are vastly different. I do not suggest that autogenous grinding is beneficial in the separation of all complex base metal ores, in fact I know of a case where autogenous grinding would be disastrous to any selective flotation. I do however contend that prospective flow sheets and reagent balances of any complex base metal ores should be tried with both types of grinding. I feel fortunate that the paper to be presented later in this meeting by Rene Klymouski will, I think, compliment and perhaps explain some of the results of my research.This paper will be in four parts. The first part deals with a literature survey on the subject. Surprisingly enough, very little information has been printed on the subject. The second part deals with results obtained in bench scale tests on an ore from Chester Mines Limited. It was in these tests that we realized that steel grinding was giving us serious problems. So bench scale tests are shown giving results with a stainless steel grind, a mild steel grind and a grind in a ceramic mill with ceramic billets.The third part of the paper deals with results obtained in the Mines Branch Pilot Plant, when again we ground the ore with three different types of grinding media. Incidentally, this has been the only pilot plant test made at the Mines Branch in which flotation products were made on both steel grinding and autogenous grinding on the same ore. The fourth part deals with two other New Brunswick ores and is intended to show that changing the grinding media effects ores other than that of Chester Mines Limited."

Jan 1, 1973

By Jean-Marc Simard, Vincent Jourdain, Denis W. Roy

"Seven lithologic units, informally characterized, were recognized in the vicinity of the Montauban orebody. The first five lie in stratigraphic order. From structural bottom to structural top these are: (1) grey composite gneiss; (2) dark grey quartz-biotite gneiss; (3) quartz-biotite-garnet gneiss hosting several calcareous, aluminous and magnesian members and gold mineralization; (4) light grey quartz-muscovite-(sericite)-biotite gneiss; and (5) metabasafts. The last two intrude the sequence: (6) amphibolite dykes and (7) pegmatite veins. The orebody lies on the inverted limb of an overturned synform verging to the west with the metabasafts marking the core of the fold. As the foliation is folded, this fold is attributed to deformation ""D2""; deformation ""DI"" being responsible for the formation of the foliation. A late brittle deformation developed shear zones with probable strike-slip motions. The refined stratigraphy and the identification of the structural position of the orebody provide new tools for regional interpretation and prospecting.RESUMESept unités lithologiques ont été définies informeffement à proximité du gisement de Montauban. Les cinq premieres reposent en ordre stratigraphique; ce sont de la base au sommet structural: (1) le ""gneiss mixte gris""; (2) le gneiss gris forcé à quartz biotite; (3) le gneiss a quartz-biotite-grenat comprenant plusieurs membres calcareux, alumineux et magnésiens ainsi que la minéralisation aurifère; (4) le gneiss gris clair à quartz muscovite- Isericitel-biotite; et (5) les métabasaltes. Les deux autres unites sont intrusives dans la sequence: (6) les dykes d ‘amphibolite et (7) les veines de pegmatite. Le gisement se sitlie sur le flanc inverse d'un synforme déverse vers I' ouest dont les métabasaltes occuperaient le cœur. Comm e la foliation est plissée, ce pli est considère appartenir d la deformation ""D2""; la deformat ion ""DI"" etant responsable de la formation de lafoliation. Une deformation cassante tardive se traduit par des zones de cisaillement, d rejet apparemment directionnel. Cette stratigraphie plus précisé et l'indentification de la position structurale du gisement fournissent de nouveaux omits de prospection et d'interprétation regionalé."

Jan 1, 1987

By L. G. Stolarczyk, J. Duncan

"SynopsisLong before the environmental movement, coal miners were suffering from occupational diseases that became apparent in the later years of service, and especially during the retirement years. Chronic exposure to micro-fine dust in the respirable range (‘float’ dust) causes various lung diseases, referred to as coal mine dust lung disease. In the USA alone, 76 000 miners have died of coal mine dust lung disease since early legislation recognized the issue in 1969. Researchers believe that reducing float dust exposure limits alone will not reverse the increasing incidence of coal mine dust lung disease seen in the current generation of miners. Trace and radioactive metals are concentrated in the thin boundary layers of the coal seam (Roberts, 2013), and hence float dust includes silica and toxic trace metals. The production and quality of coal is also significantly impacted by the presence of these contaminants in the coal. In the combustion process, the trace metals are oxidized and become incorporated in the fly ash and flue gas. Since they are extremely water-soluble, they represent a significant danger to health and the environment. Coal preparation plants and power stations need to mitigate these contaminants as far as is practical, but the simple fact is that most contaminants should have been left un-mined.This paper describes an innovative coal-cutting solution to the longstanding technology gap in mining – the ability to measure uncut coal layer thickness to the boundary rock layer. Because of constant changes in geology, seam thickness, and seam undulation, the horizon sensor must be located in the bit-block of the rotating cutter drum of the mining machine. Contaminants in ROM coal must be minimized at the source – that is, at the rock/coal crushing cone directly under the bit-tips of the cutting drum. Bittip distances to the rock boundary layer must be automatically controlled in real time when mining in a complex and undulating coal bed. Horizon sensing (HS) technology enables the mining machine’s cutting picks to stop at a specified distance from undulating horizons of the boundary rock. The thin contaminated coal layer can be left in situ, significantly reducing the toxicity of the float dust. Preventing the metal picks from striking quartz-containing boundary rock also reduces the occurrence of methane ignitions. HS technology equipped with pick force vector sensing can allow optimization of the cutting pick lacing pattern for minimum coal and rock crushing, thereby reducing float dust. This technology may enable the mining industry to convert from automated machine control to autonomous during coal cutting and loading."

Jan 1, 2015

By Joe Roby

Rolling disc cutters are the business end of hard-rock and mixed-face tunnel boring machines (TBMs). Since their first successful employment on a TBM more than 50 years ago, disc cutter technology has constantly evolved, allowing modern TBMs to excavate very hard and abrasive rock efficiently. Disc cutters have also been employed successfully on earth pressure balance (EPB) and slurry machines, cutting rock under water and ground pressure. The range of materials excavated by machines today is broader, excavation rates are higher and cutter costs are lower than ever before, proving the value of investment in cutter development. Disc cutters are used on a range of tunneling equipment, from pipe jacked slurry micro-TBMs less than 1 m (3.3 ft) in diameter to 15 m (49 ft) in diameter, hard-rock boring TBMs. The geological conditions under which they are employed range from sands and gravels, with several bar of water pressure, to extremely hard, massive rock with UCS up to 420 MPa. Regardless of the type of machine or geology, one thing remains constant: changing worn out cutters is costly. When cutters must be changed in the middle of a tunnel, the contractor incurs the cost of downtime as well as the cost of refurbishing or replacing the cutters. In the case of catastrophic cutter failures, the project can be stopped completely for long periods, and the costs mount up rapidly while tunnel production is at a stand still. Catastrophic cutter failures include the occasion when hard-rock disc cutters are failed in groups (called a ?wipeout? phenomenon) and the operator fails to stop the machine, which results in severe damage to the cutterhead. The cause of this can be either an undetected failed cutter propagating damage to surrounding cutters or operator error in steering. Regardless of the cause, the resulting damage can take days or even weeks to repair. When cutters fail prematurely on EPB or slurry machines in certain geological conditions, it is impossible to evacuate the chamber and, therefore, impossible to get [ ] into the chamber to change the cutters. The solution is frequently an unplanned intervention shaft that must be sunk at great cost. The importance of being able to predict cutter life accurately, and in all geological conditions, cannot be overemphasized. For these reasons, cutters have been developed for specific machine types and sizes, as well as for specific geological operating conditions. Different size cutters are required for different size machines. For example, while 483- and 508-mm (19- and 20-in.) cutters are used on large diameter TBMs, it is impossible to employ cutters so large on a small micro-TBM. Also, the cutter must be designed for the specific geological conditions under which it will be operating. The disc cutter rings required to bore extremely hard rock are the most expensive of cutter rings. However, they provide little advantage in weaker rock formations where less expensive rings will do the job as well. It is important to choose the correct cutter for the machine and the geological conditions in order to get the best balance of cost and risk.

Jan 1, 2009

By Paul J. Axtell

The design-build delivery system is being used to erect the landmark Christopher Bond Bridge as part of the kcICON project. The cable-stayed bridge is currently under construction and will span the Missouri River on I-29/35 in Kansas City, Missouri. The design-build process for the foundation work on this project has been successfully implemented as a result of cooperative efforts between the foundation designers and the constructors to develop a constructible design.

Jan 1, 2009

By H. Lowers, P. Hageman, S. Diehl, D. Fey

Understanding relationships between mineralogy, texture, microstructural features, and element distribution and residence in minerals, is critical for accurate modeling of mineral weathering in waste-rock piles. The morphology of minerals and deformation structures, such as veins and faults, are important factors that control: (1) fluid access to the mineral surface to initiate dissolution, (2) the distribution of trace elements, and (3) formation of secondary minerals. We characterized the mineralogy, textures, and chemical properties of waste-rock material at three sites at scales ranging from outcrop to micrometer scale. A comprehensive hand-sample to thin-section scale methodology utilizing light microscopy, scanning electron microscopy, electron microprobe, and laser ablation ICP-MS was used to thoroughly characterize the waste-rock material.

Jan 1, 2007

The Research on Refined Gold Bullions Surface Upgrading

Sep 13, 2010

The Burra Burra Mine is situated in complexly folded Torrensian dolomites and limestones forming the faulted axial region of a major anticline. The orebody mined was largely of secondary origin and confined between two faults, Kingston's on the west and Tinline's on the east. The orebody occurred at the junction between cherty dolomites and a clastic limestone with a large mass of marble breccia along its western margin. Secondary ore consisted of carbonates and oxides in the breccia and the ore bed and detrital copper minerals deposited as part of a clastic breccia in sinkholes and solution cavities in the dolomites and ore beds.Primary sulphides occur disseminated in the marble breccia and in stratiform habit in the ore bed. Kingston's so-called "lode" may be mineralized marble breccia.The marble breccia appears to be of diapiric or sedimentary origin and there is evidence to support a sedimentary origin for some of the copper sulphides. No igneous rocks have been discovered within 20 miles of the mine and any hydrothermal activities were probably at comparatively low temperature. The possibility of extensive stratiform and disseminated copper sulphide mineralization in the marble breccia and ore bed requires testing by further drilling and geophysical surveys.INTRODUCTIONThe re-interpretation of Burra Burra geology and ore formation discussed in this paper resulted from a comprehensive investigation of the mine and its surrounding district begun in December 1961 and in progress at the time of writing. (February 1963). The decision to investigate Burra Burra was taken after a thorough examination of records and reports of all non-ferrous metal deposits throughout South Australia and was given impetus by a report by Thomson (1963) suggesting a sedimentary origin for the copper mineralization. Although the author does not concur fully with Thomson's interpretation there is no doubt that sedimentary processes have played an important part in the formation of the Burra Burra copper deposit, nor is there any doubt that igneous activity played no part.

Jan 1, 1963

The lead concentration of flotation feed ore slurries is determined using two ?-ray absorption gauges mounted directly on a 6 in. diameter flotation feed pipeline. One gauge is a conventional "density" gauge using CS137. The other is a "lead-sensitive" gauge, which depends on the preferential absorption. by lead of 225 key y-rays resulting from Compton backscatter of CS137 y-rays.Gauge outputs are combined using an analogue computer the output signal of which is directly proportional to the lead concentration of the pulp. The accuracy of measurement of the pulp lead concentration is ± 3·6 per cent for ore slurries with lead concentrations in the range 0'07-0·16 g/c.c. and pulp densities 1.43-1.60 g/c.c.This paper sets out the development of the technique and details are given of the two experiments (1964, 1966) conducted in the plant at North Broken Hill Limited. The installation of the two-gauge system inthe plant during May 1968 is described. Details are given of the calibration technique used and the results obtained.

Jan 1, 1969

By Edwin W. Meyer

The augered cast-in-place piling technique was used to install deep foundations 20 feet into weathered sandstone. The project involved the upgrading of the Air Quality Control System (AQCS) for a 560 megawatt coal fired power plant located in Stillwater, Minnesota. The site subsurface consisted of 20 feet of overburden overlying weak sandstone. The overburden consisted of sands and gravels with cobbles and boulders, and variable thicknesses of peat. Ground-water at the site was approximately 8 feet deep. Two foot diameter piers were selected to facilitate installation through the cobbles and boulders in the over-burden and to penetrate the sandstone 22 feet. During installation of the first pier, the weak sandstone broke down to sand-sized material that could not be cleaned from the pier hole without the use of slurry to hold the material in suspension. However, the use of slurry would significantly impact both schedule and cost. Since the sandstone could be easily drilled with the pier equipment, it was believed that 2 foot diameter deep foundations could be installed as designed using augered cast-in-place piling techniques. A brief test drilling pro-gram was conducted to evaluate the viability of 2 foot diameter continuous flight augers penetrating 22 feet into the weak sandstone. The test drilling indicated that augered cast-in-place installation techniques should be successful. Following a short delay to mobilize the additional required equipment, construction commenced. Installation of the 2 foot diameter augered cast-in-place piling to a depth of 22 feet into the weak sandstone was successfully performed.

Jan 1, 2006

By Ian Hooper, Alan Winter, Stefan Sadokierski, Craig Covil

The existing Tappan Zee Bridge was built in the late 1950s and has been working over its design traffic load for some time now. A new project, which is being jointly sponsored by the New York State Thruway Authority and Metro-North Rail Road, is looking at new alternatives to provide new road and rail crossings of the Hudson River. These include 2 to 5 mile and potentially longer tunnel crossing options that include hardrock TBM and EPBM opportunities. The paper describes the project needs and tunnel concept design work done on some of the alternatives. It also relates to the current EIS process for the project and talks about a possible double-stacked tunnel option. It also talks about the geology and environmental constraints relating to tunneling and provides and introduction to the tunnel ventilation work necessary for tunnel crossing of this magnitude. It does not report on the bridge engineering options being evaluated.

Jan 1, 2005

By Henry P. Chandler

[Diamond, because of its extreme hardness and abrasion resistance, has an important function in precision engineering and automation. With the increasing; requirements of modern production for fine tolerances, interchange-ability, and speed, it has become even more important. In spite of the supply of other abrasive and hard materials and of ultrasonic, electrospark rued other substitute grinding, methods, world industry seams likely to absorb large quantities of diamond for industrial purposes. An increasing part of the world's needs will be supplied by manufactured diamond, which was introduced commercially by General Electric Co. in 1957. Use of diamond for glass cutting roes bark several centuries, mid diamond drilling of rock became important to the mining industry M the 1870's. Today, diamond drilling is the most extensively used method of exploring the world's ore reserves; diamond drills two also used to determined the nature of bedrock below the foundations of buildings, dams, and bridges. Diamond drill bits are now used extensively in the petroleum industry, and replacement or steel rock bits with diamond drill bits in hard rock formations has affected substantial savings.]

Jan 1, 1964

By Henry P. Chandler

[Diamond, because of its extreme hardness and abrasion resistance, has an important function in precision engineering and automation. With the increasing; requirements of modern production for fine tolerances, interchangeability, and speed, it has become even hors, important in spite of the supply of other abrasive and hard materials and of ultrasonic, electrospspark rued other substitute grinding methods world industry seems likely to absorb large quantities of diamond for industrial purposes. An increasing part of the world's needs will be supplied by manufactured diamond, which was introduced commercially by General Electric Co. in 1957. Use of diamond for glass cutting goes bark several centuries, mid diamond drilling of rock became important to the mining industry M the 1870's. Today, diamond drilling is the most extensively used method of exploring the world's ore reserves; diamond drills two also used to determine the nature of bedrock below the foundations of buildings, dams, and bridges. Diamond drill bits are now used extensively in the petroleum industry, and replacement or steel rock bits with diamond drill bits in hard rock formations has effected substantial savings.]

Jan 1, 1964

The success of smooth blasting essentially depends on geological condition of rock. Also, in the perimeter hole, borehole pressures with light, well-distributed explosive loads are important to minimise overbreak. In order to simulate perimeter holes with scaled model test, the borehole pressure was considered as a factor of scale. Hydraulic oil pressure is applied as borehole pressure instead of using explosives and detonators in order to remove the undesirable effects of detonators in an experimental set-up of just two perimeter holes in a tunnel blast. The borehole pressure on a perimeter hole is nearly reproduced with hydraulic pressure which is generated by non-electric detonators in the hermetical cylinder.

Dec 6, 2010

Eco-Efficient Gravity Separation Solutions in India Sustainable development and social responsibility issues are a principal aspect of mineral processing operations around the world. With the need for more environmentally effective technologies, some gravity separation systems have provided eco-efficient mineral processing solutions in places where it is not otherwise viable because of lack of fresh water or for other environmental reasons. Advanced spiral separation technologies developed in Australia offer a cost effective and environmentally viable way to process minerals. In particular, we review recent case studies of spiral plants commissioned in India where environmentally sustainable solutions to design problems included the use of spirals operated with sea water and the use of high capacity (HC) spirals to provide low consumption of energy and materials and a reduced plant footprint. This paper evaluates the performance of various spiral plants in India and how critical environmental issues which affect the overall viability of wet concentrating processes where resolved.

Sep 13, 2010

By Charles H. Minott, Michael J. Markow, Robert D. Wyatt, Fred Moavenzadeh

The substantial investment in tunnels anticipated in the next twenty years has focused new attention on the economics of tunnel construction itself and on some costly problems associated with underground work: the uncertain geologic conditions, the performance and adaptability of men and equipment, and the need for quicker, more efficient excavation methods. There also exists a need to develop better ways of estimating tunnel construction. Inaccuracies in current bid estimates stem from a number of causes, among them (1) the effects of geologic conditions, which are not adequately known prior to construction, (2) the dependence of actual cost on the construction method used and on the interactions among the operations occurring underground, and (3) the reliability of tunneling equipment. Inability to estimate final costs for conventional tunneling more accurately has in turn caused difficulty in gauging the costs and benefits attributable to new tunneling technologies either under development or for which R&D programs are planned. ATTRIBUTES OF THE TUNNEL COST MODEL This paper presents a computer based Tunnel Cost Model (TCM) which quantitatively assesses the uncertainties inherent in underground work, and is detailed enough to aid in preparing estimates or bids. The model employs appropriate techniques of subjective (or "degree of belief") probability and computer simulation of tunnel construction operations to estimate distributions of total tunnel

Jan 1, 1974