Search Documents

VOLUME I Volume I of this three-volume report is the result of development of a comprehensive, coordinated approach to site data-acquisition activities to produce key plans and reports during the evaluation and development of a surface coal mine. A logic diagram illustrates activities in the planning and decision-making process from exploration through post-mining monitoring. The report briefly discusses major elements, other than the site environment, which influence development of mining and reclamation plans and refers to other readily available literature for details outside the scope of this study. The essence of the rationale is shown to be the 1 employment of necessary skills at the proper time to evaluate specific data ' requirements and integrate them into a cost-effective program to produce initial and major feasibility reports, mining, and reclamation plans, and the environmental impact assessment.

Jan 1, 1976

By Arash Maghsoudloo, Asli Can

"Abstract This paper presents a ground improvement implementation case under a raft foundation of a local hospital. The selected ground improvement method is Wet Soil Mixing (WSM) technique. Soil mixing is increasingly applied to environmental applications and ground stabilization in geotechnical projects. In this technique, weak soil is mixed with cementitious slurry to improve the characteristics of the soil. The investigated case is one of the pioneering WSM ground improvement technique implementation cases in Turkey. The soil profile is mainly consisted of low plasticity clay. The effect of ground improvement is verified by a series of laboratory tests and four in-situ pile loading tests. The results of in-situ pile load tests on constructed soilcrete columns showed an acceptable factor of safety for the bearing capacity of the WSM columns. Measured bearing capacities in all four tested columns were nearly 20% higher than calculated values. In addition, a set of samples are obtained from the constructed columns and unconfined compression tests have been conducted. The laboratory test results indicate that the selected cementitious slurry has a sufficient efficiency to form the stabilizing columns.IntroductionIn the construction industry, stabilization of the soft ground by lime or cement stabilization is a widely used technique. In ground improvement systems deep mixing method (DMM) results in the same stabilization in deep portions of the soft soil profile by mixing cementitious slurry by means of mechanical augers. The pioneering cases of modern deep mixing application can be traced back to the year 1970 that was used for the stabilization of marine soils below the water level for the construction of harbor structures (Terashi et al., 1979). Nowadays, DMM is shown to be a proper and efficient method for the foundation of the structures and embankments on land. Some recent studies also reported that reasonable settlement reduction range in the stabilized soils under the foundation of structures (Archeewa et al., 2011). In addition to reduction of the structural settlement under service loads, deep mixing methods are also utilized when there is a concern with contaminated soil and groundwater or groundwater control (Andromalos and Bahner, 2003).Although, the DMM is shown to be a successful method in numerous studies for improvement of a wide range of soil types such as organics, fine-grained, and coarse grained material, it has some limitations (Archeewa et al. 2011, Jameson et al. 2010, Jelisic and Leppanen 2004, Lambrechts and Roy 1997, Meyersohn 2007, Miki and Nozu 2004, Olsson et al. 2008, O’Rourke and McGinn 2004, Stewart et al. 2004, Yang et al. 2011). High soil density and stiffness could damage deep mixing rigs. Engineering properties of the soilcrete columns changes based on the soil type, water content and other factors such as organic content of the available soil profile, so properties of the generated soilcrete should be verified by a set of rigorous testing procedures (Puppala et al. 2004).Based on the general classifications presented in the ground improvement literature, deep soil mixing method is divided into two main types of dry or wet mixing methods. In the dry and mixing methods compressed air and water are utilized as the binder transporter medium respectively (Moseley and Krisch, 2004). In addition, DMM methods can be categorized based on the employed mixing methods during the construction. In this study, the main aim is to present and elaborate on the selected method is known as Wet Speed Soil Mixing (WSSM)."

Jan 1, 2014

By J. A. Botín

In modern mining, the core of mine planning and design is the block model, a simplified representation wherein the ore deposit is divided in a number of virtual rock cubes, each characterized by technical and economics parameters. Mining engineers use this model to design the mine and develop production schedules. Traditionally, sustainability issues are not considered in the mine design, planning and engineering processes but rather are incorporated in the later stages of the feasibility evaluation as necessary expenditures and operating costs. This paper describes the results of a research project aiming to develop a methodology to incorporate sustainability parameters directly into the block model, so that they become an integral part of the design, planning and scheduling processes. It is considered that the incorporation of sustainable parameters into the block model would yield a more responsible mine design and improve mining projects sustainability performance

Feb 27, 2013

By Vinay Kumar Agrawal, Rama Nath Praharaj

IMFA Group is the largest producer of Charge chrome not only in India but also in Asia. This Group has plants situated at Therubali and at Choudwar. They also have a Thermal power plant at Choudwar which not only caters to the power requirement of Choudwar plant but also supplies power to Therubali. The plants are fed for Chromite ore through the captive mines namely Nuasahi Chromite mines (40.47 Ha) , Bangur Chromite mines(37.34Ha), Sukinda chromite mines (116.76 Ha), Mahagiri Chromite Mine(73.777 Ha) and Chingudipal Chromite mines (26.62 Ha). Nuasahi Chromite Mine, which is situated in Keonjhar district, is an underground mine and is based upon best technological advancements in the industry. The underground mining operation is certified under ISO-9002, ISO-14001and OHSAS 18001. This not only shows the concern for the quality, environment but also for the health of the employees. The Nuashahi is the first chromite mine to backfill the opencast excavations created during the last 50 years and carry out the production from underground area below the opencast workings. This paper deals with the state of art technology of sub-level open stopping in thin ore bodies. The under-ground mine openings was started in the year 1997. In next four years the production of chromite from underground was started.(2001). At present the mine is in a good shape with several running stopes. Today it is producing around 10,000 Mt per month of chromite. The development of the mine is carried out with an average of 200 mtr per month of tunneling. The mine is having a mechanical ventilator having a capacity of24000 M3 per hour at 50mm water gauge, thus feeding sufficient air for the persons working in underground. The mine is being dewatered through a most modern positive suction sump, having a capacity of 500 cum and operated with 120 HP pumps. After commissioning of this sump in the year 2003, the mine has taken a quantum jump in production with remarkable saving in power consumption.

Jan 1, 2007

By J. D. Clendenin

Systematic practices for protecting crops from frost damage began in the United Metes more then 40 years ago when the Weather Bureau Fruit-Frost Warning Service was organized; however, various practices employed in frost protection are centuries old. Although there are areas where little doubt exists as to whether protection is needed, there are also circumstances where there is some doubt as to the need for frost protection. Many factors influence this, including not only critical temperatures but also the maturity dates of the crops relative to marketing. Critical temperatures for frost damage to trees, plants, blossoms, and fruits very with weather, plant variety and nutrition, and stage of growth. In the case of truck crops, a single night of protection from frost injury might yield big dividends with a variety of sweet corn or tomato that matures early while price is high yet be worth very little with a midseason or late-maturing variety. Consequently, it is the individual grower who must decide whether to use frost-protective measures on the basis of his returns, the quantity and quality of his crop, the marketing situation, the sensitivity of his crops to frost damage, and the frequency of damaging frost in his area.

Jan 1, 1955

By Jury P. Nazarov

"At present the traditional study of crystal lattices of nmerials in a topic “flota tion mineralogy ” is used up. The present investigation is development of the a sclsical approaches to t he analy sis of ideal crystal lattices and f ormation on the basic obtained results of consultation, having practical chara cter.The strategy of develop ment floatation reagents i s offered, which basic pr inciple – complementary assembling m olecules forming surface co mpounds so thatth e steric charact eristic of the “visitor "" (of a polar gro up of molecule SAS) corresponded to the st er ic requirements of the ""o wner"" (elementary cell of a mineral), or coincided inter molecular cavities). In itsh case process of for mation of surface com pounds ca n be considered(a first approximation) as a realization of a principle of the design er "" LEGO "".The approach, which basic idea consi deration actioonf reactant ions and ions of ele mentary cell as three-di mensional objects is developed. And at suchp paroach the laws of a ster eometry - laws describin g spatial effect s are applicable. Thus it is possible toconsider a miner al surface as a mat r ix - basis for formation of the requirem ents to polar group of a molleec cuollector, and or (it is possible) depressant. As a whole approach represents a generalized principle double com plementation, enveloping both power, and geometric asp ects (concept ""lock "" and “key "" - spatial conform ity. Figure 7 (left). Fragment of a crystal lat tice of ap atite. Oleic acid ions interact on ly with th e calcium cations locate d on a long axi s of an elementary c ell. Magenta colour represe nts the calciu m cations, which are n ot particip atin g in interactio n, as th e degree of screening by ions neighbours exceeds 1.Figure 2. (right)The illustration of space complementary. “Afterbuilding” an elementary cell of apatite (radical PO4) related molecules of the visitor – alkyl phosphate (polar group PO4). Cations of calcium are not shown."

Jan 1, 2003

By Mishark Nnabuchi

A heterojunction of PbS - CuS thin film has been grown on glass slides by SGT. The films were annealed for 1hr at temperature of 373K and 423K respectively. The optical properties were characterized using a UNICO UV - 2102 PC Spectrophotometer at normal incidence of light in the wavelength range of 200 - 1000nm. The minimum percentage transmittance was observed to be 34% for sample A and 25% for sample B within the same optical region. The band gap energy was determined from the spectra to be 2.05eV for sample A and 1.85eV for sample B which gave a band shift of 0.20eV. It can thus be concluded that the optical properties of the films within the VIS - UV - NIR can find application in solar thermal technology, particularly as antireflection coating, window materials and as good materials for selective solar cell fabrication.

Jan 1, 2010

Tellurium (Te) is one of the least abundant elements in the crust and tends to form minerals associated with copper, lead, zinc and iron sulfide deposits. Today, most tellurium production comes from the anode slimes and other wastes generated in metal refining. Most of the current tellurium produced in the world is used as an alloying agent in iron and steel, as catalysts, and in the chemical industry. However, future demand and production could increase because tellurium is increasingly used in solar panels and some electronic devices. Tellurium minerals are found in Au-Ag districts in New Mexico, but were not considered important exploration targets in the past. In New Mexico, tellurium is found associated with porphyry copper deposits in southwestern New Mexico and with Au-Ag veins in the Eureka, Sylvanite, Organ, Lordsburg, Steeple Rock, Wilcox, Mogollon, Chloride, Cuchillo, Hillsboro, Zuni Mountains, White Oaks, and Nogal-Bonito districts. The only tellurium production from New Mexico has been from the Lone Pine deposit (Wilcox district), where approximately 5 tons of tellurium ore was produced. Gold-tellurides are found with gold, silver, pyrite, and fluorite in fracture-filling veins in rhyolite at Lone Pine, with reported assays as much as 5,000 ppm Te. Other districts in New Mexico have potential for tellurium, but require field evaluation.

Feb 27, 2013

By E. R. Bauer

In response to the mandates in the MINER Act of 2006, NIOSH conducted refuge alternatives research that included characterizing the utility, practicality and survivability of refuge chambers and outby safe havens. NIOSH also prepared and delivered a report to Congress in late December 2007 that summarized the findings of the research, included recommendations concerning the design and performance specifications for refuge alternatives, and focused on specific information that could inform the regulatory process on refuge alternatives. This document highlights NIOSH's research and recommendations concerning refuge alternatives, survivability evaluations of refuge chambers, and presents a brief review of the current deployment of refuge chambers in underground coal mines in the U.S. The research has lead to the conclusion that refuge alternatives have the potential for saving the lives of mine workers if they are part of a comprehensive escape and rescue plan, and if appropriate training is provided. DISCLAIMER: ?The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.?

Jan 1, 2009

By G. R. Fitterer

In the manufacture of steel by any process the refining period involves the partial elimination of the metalloids carbon, manganese, phosphorus, and silicon, by virtue of their reactions with ferrous oxide. At the end of this refining stage the metal consists chiefly of iron in which small amounts of these materials are dissolved. Unless some deoxidizer is added to the steel at this time, the reaction between carbon and ferrous oxide will continue with such force that it is impossible to form sound steal in the ingot molds. Instead, the product will exhibit a marked porosity due to the formation and trapping of carbon monoxide-the product of the reaction mentioned. However, if deoxidizers are added, steel may be obtained which is dense and free from gas bubbles. At the same time the deoxidation products will remain in the steal as impurities. For example, silicon additions form Si02 or combinations of Si02 and FeO. Additions of manganese form deoxidation products consisting of various proportions of MnO and FeO. It is also quite obvious that simultaneous additions of manganese and silicon will form oxide combinations either in the binary system MnO-SiO2 or in the ternary system FeO-MnO-SiO2. Work at the Pittsburgh Experiment Station of the United States Bureau of Mines, in cooperation with the Carnegie Institute of Technology and the Metallurgical Advisory Board, involved the study of such deoxidizing reactions and their products. In this connection considerable information is necessary concerning FeO, MeO, Si02, and Al 203, and their various combinations. Some of the most needed data are the melting points of all of these materials. At the outset of this work ordinary methods of melting point determinations were found to be inadequate for various reasons, and the procedure finally selected involved the use of the micropyrometer with occasional corroboration by quenching methods, The reasons for this selection, together with a description of the apparatus, are given in the following pages.

Jan 1, 1932

By Martin Plante, Denis Hamel, Marie-Pier Bédard, Jeff McLaughlin

"The results and methodology for the optimisation of the zinc flotation circuit at the Matagami Mill using the 6-Sigma methodology are shown in detail while only the base line and final results are presented for the copper circuit. As a result of the six sigma project, the zinc concentrate grade was improved by 2% and the zinc recovery by 3%, with reduced dosage of reagents while the copper concentrate was improved by 2.4%. The process variation in the zinc concentrate grade and recovery was also reduced by over 50%. The main factors contributing to the project success were identified to be improvement in the plant measurement systems, an internal benchmarking exercise and statistically designed laboratory and in plant tests to guide the process improvement. The annual value to Noranda resulting from this project has been estimated at approximately $5 million.INTRODUCTIONThe Matagami concentrator started ore processing from the new Bell- Allard deposit in July 1999. Concentrator performance (grade and recovery of zinc and copper concentrates) was highly variable and work was ongoing to fix the sources of variation. In the mean time, Noranda embarked on its 6-Sigma initiative across the company. The 6-Sigma DMAIC (Define, Measure, Analyse, Improve, Control) methodology was used in the two flotation circuits to reduce variation and improve performance. The statistical 6-Sigma methodology moves towards identifying and controlling critical process operating variables (the X' s) to achieve customerspecified performance (the Y's). The goal of the methodology is to describe a process in a numerical equation known as the transfer function, given as Y = f (XI, X2, X3.. .), where Y could be concentrate grade or recovery and examples of X's are reagent dosage, particle size, etc. With the transfer function, optimal operating conditions and control tolerances are established for the key X's to ensure the desired Y performance is obtained.Each phase of the 6-Sigma methodology is explained below with examples from the Matagami project."

Jan 1, 2001

By N Clarke, G R. Ballantyne, M S. Powell, P Elms, A Anyimadu

AngloGold Ashanti Ltd nominated Sunrise Dam Gold Mine as a case study via their involvement with the long-running Australian Mineral Industry Research Association (AMIRA) International P9P research program (AMIRA, 2015) . A group of researchers from the Global Comminution Collaborative (GCC) conducted a comminution circuit survey and review together with a large group of graduate metallurgists, senior metallurgists and operators. Fundamental and applied research understanding was used to identify productivity and efficiency improvements around the crushing and grinding circuits. The limitations of current scientific knowledge were identified through this process and this will allow future research to be more focussed on what is required by industry.The comminution circuit at Sunrise Dam comprises three stages of crushing followed by two stages of ball milling. The secondary crusher and primary ball mill classification were identified as the primary limitations of the circuit. The secondary crusher was found to be underperforming through overall equipment efficiency (OEE) analysis and an improved chamber design was identified by Chalmers University. This improved design will promote higher power utilisation, choke feeding and a finer crushed product for the milling circuit. The primary ball mill product is classified by a combination of a trommel, 3 sieve bends and a hydrocyclone. The combination of poor classification and coarse, competent feed led to a situation where the primary mill was overfilled with rocks, reducing grinding rate due to cushioning of impact. Size specific energy (SSE) benchmarking methodology was used to identify that a 10% increase in throughput could be achieved with improved primary classification.CITATION:Ballantyne, G R, Clarke, N, Elms, P, Anyimadu, A and Powell, M S, 2015. Application of research principles to identify process improvement at Sunrise Dam Gold Mine, in Proceedings MetPlant 2015, pp 221–229 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

The wealth of a nation can be measured many ways, but one of the most important measures is its natural resources, particularly minerals. Minerals provide the foundation upon which economic prosperity and defense preparedness rest. Assessing our energy and mineral resources and assuring their development is in the best interests of all our people continues to be an important national goal. Since its founding in 1910, the U.S. Bureau of Mines has established itself as the world's premier minerals information and research agency. Its authoritative, comprehensive data and pioneering research have contributed significantly to a strong U.S. mineral position in the world.

Jan 1, 1990

By Winfried Rosenstock

The development of electronic initiation systems has partially reached or will reach in a short period of time full reliability for general use without limitations. Unfortunately those systems meet with a fully unprepared mining community and is confronted worldwide with blasting procedures which are not suitable to exploit the full range of the electronic option. This is for the time being only belonging to quarrying and general surface mining, for the use in underground operations the detonator is still not yet competitive, apart from special cases. It is not to be taken in doubts that the introduction for underground purposes will follow in a less shorter or longer period of time.

Jan 1, 2003

By Randolph R. Dreher, Michael L. Schreder

"In recent years, FFE Minerals has designed, installed and commissioned several large grinding mill circuits. This paper discusses the issues related to the erection and commissioning of large grinding mill circuits. The three circuits discussed are Collahuasi in Chile, Minera Los Pelambres in Chile, and Century Zinc in Australia. These circuits include large SAG and ball mills with both gear and gearless drive arrangements, as well as, both trunnion and shell supported mills. Aspects of these features are discussed with respect to their impact on installation and commissioning. While the normal challenges of mill erection and start-up were experienced, there were also a few unexpected challenges encountered partly due to the large scale of the equipment. An overview of the equipment and design ratings of these circuits is also provided.COLLAHUASIOverviewThe Collahuasi mills were started-up in November of 1998. The site is located in the Andes Mountains at an elevation of 4300 meters. The grinding circuit includes two lines featuring one SAG mill and one ball mill for each line. The circuit features a recycle conveyor around the SAG mills with provision for adding a pebble crusher in the future. The design tonnage of the grinding plant is 60,000 MTPD with an ore BWI of 10.5 kWh/MT.The SAG mills are 32’ x 15’ (1 3’ EGL) with 10,800 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The mills are driven by low speed synchronous motors with CCV variable speed drives. The SAG mills are trunnion supported and use hydrostatic lubrication. Feed to the SAG mills is via a rock-box type feed chute on a cart. The mills discharge on to trommel screens with a bucket wheel to remove the oversize.The ball mills are 22’ x 36.5’ (36’ EGL) with 12,500 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The fixed speed mills are driven by low speed synchronous motors with GE Quadramatic load sharing drives. The ball mills are shell-supported and feature multi-pad bearings with hydrodynamic lubrication. The mills are fed via a rubber lined sump box with feed spout on a cart. The ball mills also discharge on to trommel screens. Twenty-six inch (26”) diameter hydrocyclones are in closed circuit with the ball mills."

Jan 1, 2001

By F. Habashi

Siberia, a vast country rich in mineral resources and a large number of different ethnic groups. To the east of Lake Baikal is Buryatia with capital Ulan Ude. The Buryat are closely related to the Mongolians. Ulan Ude is connected to Ulaan Baatar (Ulan Bator) the capital of Mongolia by train – a 26 hours trip. Getting a visa to Russia is not a simple case. Visits to metallurgical research laboratories, Lake Baikal, and historical museums are enriching experience.

Jan 1, 2006

The Bureau of Mines is active in programs pertaining to solid waste disposal and land reclamation. Nine reclamation projects of mining companies and six projects of the Commonwealth of Pennsylvania were investigated to provide information on the procedures, costs, and results obtained from reclamation projects of bituminous coal-waste disposal areas. Refuse disposal costs of mining companies ranged from 9 to 28 cents per ton-mile, and quantities disposed of ranged from 600 to 4,500 tons per day. Spreading and compacting the refuse at the dump site ranged from 3 to 20 cents per ton. Cost of covering with soil and planting ranged from $750 to $1,646 per acre. Total costs of reclamation for the Pennsylvania projects ranged from about $1,800 to more than $15,000 per acre. Refuse preparation costs ranged from $772 to $5,550 per acre. Soil covering and planting costs ranged from $1,083 to $5,086 per acre. The best results were obtained by soil preparation and conditioning prior to planting. The type and depth of soil and effect of climate were also factors.

Jan 1, 1973

By D. Kachongo, Y. Cheng, A. Kashala, D. Samal, G. Mitshabu

Many copper processing flowsheets in the Democratic Republic of Congo include the leaching of oxide ores containing copper and cobalt, copper solvent extraction, copper electrowinning, and precipitation of cobalt salt. Recently, cobalt price gained momentum, driven mostly by the fast-growing electric vehicles battery market. The ore blending scenarios tend to prioritise high cobalt grade ore, whatever the content of copper and other impurities. Therefore, many copper solvent extraction circuits are running below design capacity. The variability of feed induces a variability of the leach solution with respect to copper, manganese, and silica contents. It is thus important to adjust hydrodynamic and metallurgical parameters of the solvent extraction plant to optimise metallurgical performance, production cost, and the quality of the copper electrolyte. This paper presents some results on how solvent extraction plant parameters have been managed in two solvent extraction plants running with lower than designed copper input. INTRODUCTION Referring to a report of the chamber of commerce of the Democratic Republic of Congo (DRC) the online publication Agence Ecofin (2019) indicated that the DRC ranks in the fifth position of the world top copper producing countries with over 1.2 million tons produced in 2018. The same year, 66% of the world’s cobalt was produced in the DRC at over 106,000 tons. If the political situation remained stable and the new tax regime introduced in 2018 did not deter private investors, copper production could reach 1.4 million tons/a in 2020 as pointed out in Mining.com (2019). Forecast figures for DRC cobalt production vary widely depending on analysts. The DRC online magazine Actualité.cd (2018) referring to a ministerial source forecasts over 141,000 t cobalt/a for 2020. The reality will depend on many factors, including the selling price, the supply compared to the demand, and finally the reaction of investors to the new DRC tax regime. The growing electric vehicle batteries market has been the major key driver of the price of cobalt. The five years historical cobalt price graph in figure 1 from infomine.com (2019) shows that the price of cobalt peaked at over 40 USD/lb in the first quarter of 2018. Cited by the online Magazine Creamer Media, Smith (2019) has indicated that the long-term demand of cobalt will likely remain strong.

Jan 1, 2019

By Dominique Vié

Standards methods covers the procedures for testing deep foundation to determine the force and velocity response to an impact of a pile driving hammer or similar device. The results of analysis generally include an assessment of pile integrity and the value of maximum dynamic stresses. But evaluation of static bearing capacity remains a matter of individual engineering judgment. A new 1D finite elements model has been developed for dynamic stresses and velocity analysis. Following an international benchmark of bearing capacity prediction organised by the Belgium Building Research Institute (BBRI), 12 piles in a site of fissured stiff tertiary clay tested in 1999, and 12 piles in a site of dense sand tested in 2001, comparison are proposed between analysis of dynamic tests and static tests results. A procedure is proposed to take in account the results of dynamic test for evaluation of bearing capacity.

Jan 1, 2002

Pipe Flow Stability of Concentrated Coal-Water Suspensions in the Presence of an Electric Field

Sep 13, 2010