Search Documents

By S. Sarac

In this study, graphical and mathematical methods used to determine operating points in single or multiple fan ventilation systems are summarized. The problem is mathematically formulized for parallel connected fans in which analytical solutions are not possible. For n number of parallel connected fans, a non-linear equation system that consists of n number of non-linear equation sis derived. The Newton-Raphson method, which is a numerical analysis method, is adapted to solve this non-linear equation system and the solution steps are given as an algorithm. A computer program based on this algorithm is written and its applicability is proved.

Jan 1, 2000

By Paul Staples, Fred Woodcock, Robert Grant, Mike Cooper

"Noranda's Brunswick Mining Division, near Bathurst, New Brunswick, processes 10,500 TPD of complex Cu-Pb-Zn bearing ore. Brunswick uses conventional rod and ball milling techniques to achieve a flotation feed size of 75% passing 400 mesh. Over a two year period, testwork was performed using a Marcy pilot plant ball mill to assess the impact of several key variables on secondary grinding efficiency. Four graded mill charges were used to compare balls and slugs at 25 and 29 mm sizes. Data was evaluated by determining grinding rates using a commercially available steady state simulator. Results were critical in Brunswick's efforts to achieve finer grinds while minimizing cost per tonne.IntroductionBackgroundThe Brunswick orebody is an extremely fined grained volcanogenic massive lead, zinc, copper, silver, iron sulphide body between two metamorphosed sedimentary and felsic volcanic rock units. Pyrite content is about 60% with 20% non-sulphide minerals, mainly silica and chlorite.Size reduction at Brunswick is performed by three separate parallel lines consisting of rod mills, primary and secondary ball mill circuits, all in series. The line 3 grinding circuit is presented in Figure 1."

Jan 1, 1997

By A Tinnelly

Land disturbed by alluvial gold mining should be restored to a capability or productivity as good as that which existed prior to disturbance.   Effective rehabilitation requires detailed planning prior to mining and must also be closely integrated with the mining operations.   The main constituents of a rehabilitation plan: description of existing site conditions, choice of final land use, establishment of final landform, water management and erosion control, soil reconstruction, revegetation and management of rehabilitated land are briefly described.

Jan 1, 1989

Adhesion of Escherichia coli onto Oxide Minerals - Extended DLVO Theory and Flotation Behaviour

Sep 13, 2010

By Martin H. Stanczyk

Bench scale, laboratory batch attrition grinding tests were made of a coarse commercial kaolin in a stainless steel, 5-inch-diameter attrition grinding machine to study the effect of a number of basic operating variables on particle size reduction and electric energy consumption. The results of the investigation showed that the more important operating variables influencing the efficiency of kaolin comminution and energy consumption requirements were type, size, and shape of grinding media, grinding media to clay weight ratio, peripheral rotor speed, clay slip pulp density, degree of pulp dispersion, and the angular arrangement of the rotor and stator bars. The tests also indicated that variables having less influence on grinding efficiency and energy consumption were pulp temperature, design of rotor cage, rotor clearance, rotor-stator bar interval, addition agents, pulp level, degree of pulp aeration, and chamber liners. The research showed that grinding media had the greatest influence on abrasion of machine parts and that spherical-shaped grinding media were superior to sharp angular or long bladed media with respect to media degradation, machine abrasion as well as grinding efficiency.

Jan 1, 1968

By A. Thielen

In experiments for the production of steel the principal problem has always been the introduction into, or removal from, the iron of a definite quantity of carbon. Although the solution of this problem had engaged a more or less blindly and empirically directed effort for a long time, it was only with the development of analytical chemistry that the rôle which carbon plays in the constitution of steel was disclosed in its full significance, and that many of the problems confronting the steel-maker were thereby more clearly defined than before. For a long time, and to a certain extent even to this day, the percentage of carbon in steel has been the controlling means of deter mining its quality and hardness. In many cases the percentage of carbon alone has been relied on for judging large consignments, such as the large deliveries of wire-billets and blooms to America during the past twenty years; and though to-day the influences of the other constituents are recognized and many other considerations are taken into account, and though, moreover, some special steels, such as the Hadfield manganese steel, apparently dispense to a certain extent with the assistance of the carbon, yet fix our Bessemer, Thomas, Siemens and crucible steel the carbon still remains one of the most important constituents, and I venture to say it is indispensable. In order to produce in the Bessemer converter a steel of a certain required percentage of carbon, two methods, as is well known, present themselves. By the one the decarburization process is stopped when the desired carbon limit in the bath has been reached ; by the other the bath is completely decarburizecl, and then a calculated amount of carbon added in the form of spiegel, ferro manganese, etc. In Germany the latter method only was adopted, and it was retained when the Thomas-Gilchrist process for the production of low-Phosphorus steel from high-phosphorus iron eame into use, since from the nature of the new process complete decarburization is neces-

Jan 1, 1891

By Michael Hamilton

Mineral resources have been identified at seven properties in the, Middle Fork Judith study area (fig. 1, and table 1). Commodities consist of silver, gold, copper, lead, zinc, and marble. Eleven properties (fig. 1 and table 2) have potential for discovery of silver, copper, lead, zinc, or sapphire resources. Of principle interest are the mineral deposits within contact zones between the Yogo intrusive complex and the surrounding Paleozoic sedimentary rocks. Contact alteration zones along the southern slopes of Yogo Peak have been prospected in a 2- to 3-mi (3.2-to 4.8 -km) long belt within the study area.

Jan 1, 1982

By J. W. Thompson

ESTATE IN MINERALS. Minerals beneath the surface may be made the subject of separate ownership either by a grant of the minerals by the owner of the land or by a grant of the land excepting the minerals, and thereby an estate in fee simple is created in the minerals, as corporeal things real. Colby, In re, Iowa, 169 Northwestern 443, p. 444. DEEDS EXCHANGING DIFFERENT MINERALS-RIGHTS OF PARTIES. The lands of two adjoining owners were underlaid with cement rock and clay at a depth of about 100 feet from the surface and with coal veins some 600 feet below the surface. By an exchange of deeds one of the land owners conveyed to the other the cement rock and clay with the right to mine and remove the same without entering upon the surface, but the deed contained no covenant not to injure the surface. The other deed conveyed the coal seam and so much of the rock and other minerals just above and below the coal as might be required in connection with the mining and removing of the coal, together with the right to mine and remove the same, and the adja- cent rock, clay, and other minerals, without entering upon or injuring the surface, with one immaterial exception. The deeds do not define the word "surface" and neither expressly nor by implication did they secure to the coal owner the right to subside the overlying cement rock; but the implication is to the contrary, as the deed gives the right to mine and remove coal without entering upon or injuring the surface. The provision that the coal owner should not enter upon or injure the surface amounts to a clause that the coal mine. shall not be worked so as to let down the surface and this does not create any inconsistency with the provision giving the right to mine and carry away the coal.

Jan 1, 1919

By T. R. Paquin

Powerful, easy to manipulate, ventilation modeling software is readily available to most mining engineers. Too often when preparing an initial ventilation model, engineers will go overboard in their design, creating a complex model with hundreds of branches. When, in practice, the creation of a less complicated ?to the point? model, containing a few well-constructed branches, would have delivered the same results. In this paper the author will demonstrate, by using actual feasibility report examples, that when designing a ventilation model, engineers should make more use of the K.I.S.S. (?Keep It Simple, Stupid?) Principle. As mining industry consultants we must continue to improve on, and deliver timely and cost-effective results to our customers.

Jan 1, 2009

By G. W. Jones

Fires in anthracite refuse banks are troublesome and may become exceedingly costly to combat. Instances are known in which refuse-bank fires have grown to such magnitude that entire mining properties have been endangered. In one instance4/ a refuse-bank fire cost the mine management several hundred thousand dollars to extinguish. The exact number of fires formerly existing or now active in the anthracite region of Pennsylvania is not known. There are hundreds of anthracite refuse banks in this region, some very high and large in area, that have never caught firs, although a few are over 50 years old. This would indicate that spontaneous ignition of the material in these banks is improbable, a conclusion confirmed by recent laboratory research.

Jan 1, 1939

By P. -É. Boileau, M. Smets, T. Eger, J. Boutin

Long-haul dump (LHD) vehicles used in underground mining are known to expose workers to important levels of whole-body vibration1. These vehicles are generally designed without suspension and may be categorized as small or large LHDs depending on whether their respective load capacities are lower or larger than 3.5 cubic yards. While the majority of older vehicles are equipped with a rigid or unsuspended seat, more recent LHDs often incorporate a suspension seat. The objective of this study was to define the vibration spectral characteristics of most commonly encountered large and small LHD vehicles operating in mining operations. This was done in an effort to categorize the vehicles in terms of vibration spectral classes to be reproduced on a laboratory whole-body vibration simulator to assess the vibration attenuation performance of a typical LHD suspension seat. Methods Vertical vibration measured at the seat attachment point of 8 small and 8 large LHD vehicles operating underground in typical mining operations under loaded and unloaded conditions was considered as the basis for defining the spectral classes. By regrouping the data collected for each LHD vehicle size and load condition, the overall distribution of acceleration power spectral density (PSD) of measured floor vibration was determined over the 0.5 to 20 Hz frequency range. Mean and envelopes of maximum and minimum values of PSD spectra were computed to define the spectral classes, along with the corresponding values of frequency weighted rms acceleration determined in accordance to the ISO 2631-1 standard2. These spectra were further used to calculate the displacements needed to drive a whole-body vibration simulator consisting of a platform supported by two servo-hydraulic actuators having a total stroke of ±100 mm. For validation purposes, the vibration acceleration spectra measured on the simulator were compared with the target spectra representing the spectral classes. Finally, the vibration transmissibility characteristics of a typical suspension seat were determined under sine sweep excitation using both a rigid mass load and a human subject having a mass of 62 kg and 85 kg, respectively. The SEAT value, representing the ratio of seat to base frequency-weighted rms acceleration, was further measured under each of the defined LHD vibration spectral classes by loading the seat with an 85 kg subject. Tests were repeated three times and the mean SEAT values were determined to assess the seat’s ability to reduce exposure to whole-body vibration in LHD vehicles. Results Three spectral classes applicable to both loaded and unloaded conditions were defined as shown in Figure 1: one for large and two for small LHDs. The influence of load on frequency-weighted rms acceleration was found to be negligible for large and Class I small LHDs, while a shift of the peak acceleration PSD to lower frequencies was noted for the loaded vehicles. The influence of load was found to be more important for Class II small LHDs. Table 1 provides a

Jan 6, 2006

By Charles W. Daugherty, James P. Gould, Kenneth R. Ware

INTRODUCTION As illustrated in Figure 1, the Washington Metropolitan Area Transit Authority's (WMATA) rapid transit system (METRO) ultimately will comprise 100 miles of line divided among 10 routes. At this time about 46 per cent of the system is under construction or in operation. Planning and design of an additional 38 per cent is at an advanced stage. Of the 84 miles under development or construction, about 10.4 miles consist of soft ground tunnels, and another 1600 feet of mixed face. This paper describes most of the factors considered by designers in setting grades for such tunnels. It is hoped the paper will be a useful guide to planners and engineers in developing similar transit systems. The problems faced in Washington, including those related to geology, are not so unique that the solutions cannot be applied to other systems. The paper also may be of interest to contractors who have not perceived the logic behind the selection of a particular vertical alignment. An attempt is made to explain the background constraints that make most tunnel alignments a compromise among competing alternatives. Readers might assume that the choice of alignments is largely controlled by geological conditions. In fact this is merely one of many factors to be considered.

Jan 1, 1976

By Terry G. Montgomery, Eric S. Weiss, John E. Going, Kenneth L. Cashdollar

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRL Lake Lynn Experimental Mine (LLEM), and after laboratory explosions in the PRL 20-L chamber and the Fike I m3 chamber. The dusts studied included both high- and low-volatile bituminous coals. Low temperature ashing for 24 h at 515 °C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as, or higher than the initial incombustible content. The MSHA alcohol coking test was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared with the initial dust loadings to determine the transport distance of dust during an explosion. All these data will be useful in future forensic investigations of accidental dust explosions in coal mines, or elsewhere.

Background: Frictional ignitions continue to be a problem facing the U.S. underground coal mining industry. Many methane igni-tions are associated with the impact of mining machine cutter bits on quartzitic material (e.g., sandstone) during the coal-cutting process. Most ignitions result in small methane-air fireballs often only a few feet in size and limited to the cutter head location. However, under certain conditions, frictional ignitions can lead to larger methane explosions and/or fires with the potential for causing serious injury or death to the mining machine operator and other nearby miners. The requirements for a frictional ignition are a flammable volume of methane-air and an ignition source. This source is usually the hot streak caused by the frictional impact of the mining bit on hard rock, and the frequency of occurrence increases with increased bit wear. Another possible ignition source is the fric-tional impact of rock on rock during a roof fall.

Mar 1, 2008

By Robert W. Decker

This report presents a survey of published novel coal cutting (mining) concepts and a brief discussion of each one. A preliminary evaluation follows which identifies promising concepts, emphasizing reduced dust generation and economic production potentials. The promising concepts are then studied more deeply and evaluated in more detail with recommendations given for further development action. The concepts recommended for further work include: Roan and Pillar Mining: Deep Cutting Continuous Miner Linear Cutting Rotary Head Miner Longwall Mining: Oscillating Continuous Water Jet Miner Deep Cutting Shearer

Jan 1, 1981

By J. Martinovic

The large proportion of gangue minerals present in platinum bearing ores in South Africa provides challenges to the flotation and downstream processes. In order to take effective measures to reduce their recovery in flotation, an understanding of the mechanisms and factors influencing their behaviour is needed. Typical gangue minerals are pyroxene, feldspar, quartz, chromite and talc. Of these, talc is a naturally hydrophobic mineral and although it is present in relatively small quantities, it has a disproportionate effect as it has a strong froth stabilizing effect, increasing the recovery of other gangue minerals by entrainment. Talc recovery is effectively reduced with the addition of polymeric depressants. Although the other gangue minerals are assumed to be hydrophilic and their recovery by entrainment is expected to follow the water recovery, there is some evidence that they may be activated by the typical reagent suites used. Reagents such as copper sulphate, added as an activator, and collectors are used to selectively induce hydrophobicity on the sulphides. It has been shown that some of these gangue minerals can be activated. This research work investigates whether inadvertent copper activation is mineral specific and evaluates the mechanisms and factors affecting the reversal of activation with the addition of the depressants using electrokinetic measurements, adsorption and microflotation tests. Results are presented that show that the selected minerals do respond differently and that the reversal of activation is dependent on mineral type, depressant type, dosage and ionic strength of the electrolyte.

Jan 1, 2005

By N. R. Williams

Black Mountain, a polymetallic base metal mine located in the Northern Cape territory of South Africa has been blessed with high grade economic ore for many years. Now that the Broken Hill orebody is nearing the end of its life, a lower grade orebody (Swartberg) is being exploited to supplement production from Broken Hill. In addition, ore from stopes in the upper levels of the Broken Hill orebody is considerably tarnished (oxidized). As a natural result, the remaining ore contains a higher percentage of magnetite, pyrrhotite and pyrite than in earlier years. Bismuth, cadmium and cobalt also occur in the ore in higher quantities. The life of the mine has been lengthened with the discovery of further deeper-lying ore reserves extending from the Broken Hill orebody suitably called the Deeps section. However, to bridge the gap between development of the new reserve and the exhaustion of the old reserve, these lower grade and tarnished (oxidized) ores have to be treated. The mine has had reasonable success in identifying unfavourable or problematic ore types and stockpiling them separately to blend in small quantities with more favourable ore. Bench and plant scale tests have aided identification of the various ore types and significant improvements in flotation metallurgical results have been seen. Copper, lead and zinc metal occur as sulphides in the ore. The mill consists of a differential and sequential flotation process that extracts copper concentrate, lead concentrate and zinc concentrate respectively with silver metal recovered in the copper and lead concentrates. This paper describes the ore blending strategy employed at the mine to maximize the econo-metallurgical efficiency of the operation.

Jan 1, 2001

By J. Garretson

When mining accidents occur, workers often become trapped and/or incapacitated. Current rescue operations can be dangerous and too slow to produce favorable outcomes. Currently, no method exists for rescue crews to scout ahead at critical times to assess the situation. Sandia National Laboratories (SNL), through a National Institute for Occupational Safety and Health (NIOSH) sponsored program has developed the Gemini-Scout mine rescue platform. The Gemini-Scout was created to assist in underground mine rescue missions. It has been designed to go into potentially hazardous environments to assess the conditions (structural, air quality, temperature). In addition, it will enable two-way communications with potential survivors prior to human rescue teams being able to enter the area. The Gemini platform is a dual tracked-chassis design, which gives the robot excellent mobility in unstructured environments. The design includes a passive 2-degree of freedom joint between two identical bodies allowing for ±30deg of pitch and roll. In addition to the base mobility platform, the Gemini-Scout incorporates many other features to help it succeed in its underground mission. The electronics are mounted in explosion proof housings to ensure safe operations in hazardous gas environments. The platform is also able to operate in up to 18in of standing water with its elevated pan/tilt cameras for navigation. A four-channel video link and Two-way audio on the vehicle help to ensure located survivors can communicate with the robot operators. The platform also incorporates a Mine Safety and Health Administration (MSHA) approved multi-gas sensor to monitor air quality. SNL believes that this technology is broad enough to be appealing to other first responders, such as police, firefighters and medical personnel. Gemini could easily be fitted to handle earthquake and fire scenarios, and it could provide relief in currently inaccessible situations.

Jan 1, 2012

By AIME AIME

American Institute of Mining Engineers. (Organized in 1871, and Incorporated in 1905.) OFFICERS. For the year ending February, 1906. Directors JAMES GAYLEY (President), R. W. RAYMOND (Secretary), FRANK LYMAN Treasurer). T. A. RICKARD NEW YORK, N. Y. CHARLES H. SNOW NEW YORK, N. Y. R. W. RAYMOND NEW YORK, N. Y. (Terms expire February, 1906.) JAMES GAYLEY NEW YORK, N. Y. FRANK KLEPETKO NEW YORK, N. Y. FRANK LYMAN NEW YORK, N. Y. (Terms expire February, 1907.) JAMES DOUGLAS NEW YORK, N. Y. JAMES F. KEMP NEW YORK, N. Y. ALBERT R. LEDOUX NEW YORK, N. Y. (Terms expire February, 1908.)

Jan 1, 1906

Background Chronology 2008 Positions May 8, 2010 Summit Going Forward Say one thing and do another ??Genuine passion to see our customers succeed?, ?A passion for exceeding our customer?s expectations? Self serving actions to gain competitive advantage at the expense of the customer No single supplier or technology can manage the overall mine and its integrated operation - April 2005: Informal meeting at Toronto CIM 2004 -Unanimous interest - July 2005: Formal Calgary Meeting, developed: - Scope and vision statement , - OEM/OTM communication plan, - industry communication plan - Aug?Nov 2005: Aligned with SMART - Nov 2005?May 2006: Direct OEM, OTM communication - May ?Sept 2006: Developed baseline standards - Sept -April 2007: Developed SMART document - Sept 2007: Document distribution and request OEM OTM response - Jan ?May 2008: Acquired OEM OTM feedback and positions May 2008: Results presented to SMART and discussions on next steps

May 1, 2010