Search Documents

By Yves St-Amour, Vince Luongo

This paper will discuss one of the largest construction projects the City of Portland has undertaken. This phase of the Willamette River Combined Sewer Overflow (CSO)project consists of approximately 18,500 ft of tunnel in soft ground, requiring the construction of six deep shafts and jet grout ground improvement. The purpose of the project is to reduce volume of combined sewerage overflows from the drainage areas on the west side of the Willamette River. Bencor-Petrifond-Pacchiosi Joint Venture was awarded a contract to design and construct six deep circular shafts, jet grout ground improvement for three bridges and jet grout ground improvement break-in/outs for some shafts. Of the six shafts the Pumping Station Shaft was the deepest and largest, requiring a permanent ground support system with a deep jet grout ground water cut-off to 335-ft deep. The joint venture used state of the art methods and equipment to achieve its objectives and build the structures through some very difficult alluvial soils to great depths next to the Willamette River. The paper will provide a general discussion of the shaft construction and jet grout ground improvement installed for this phase of the project. It will also discuss some of the technical challenges encountered while effectively managing risk and costs, resulting in a successful project completed in a timely manner.

Jan 1, 2005

Pese a tener cajas sólidas en su estructura, algunas vetas desarrollan un relleno frágil, ocasionando problemas futuros de sostenimiento para el "corte y relleno" de los mismos. Por ello, se utilizó el método de los "Square Sets", donde además de ser costoso, implicaba eliminar una proporción de la roca encajonante y diluía el contenido metálico de los filones. En ese sentido, el objetivo del texto es señalar la viabilidad del "método Cornish"como método alternativo, económico, de rendimiento óptimo y que no presenta riesgos para el personal o la labor realizada. Este método es aplicable en aquellas vetas uniformes no falladas, que tengan desde una potencia pequeña hasta aquella que sea posible apuntalar, así como en aquellas que requieran sostenimiento del techo en la veta mima o donde se realizen Shrinkages. El proceso del método se basa en la preparación de los tajeos, luego en la explotación(perforación y disparos), enmaderado, relleno del tajeo, recuperación de madera, las variantes en la preparación del tajeo y la recuperación del mineral. La única desventaja que ofrece este método es su peligrosidad, dado que si se aplica en zonas inadecuadas o sin la supervisión que garantice el cumplimiento de las normas preventivas, es preferible el uso de los "Square Sets". Sin embargo, la aplicación del método resulta mucho más productiva en rendimiento teórico puesto que alcanza de 7 a 10 toneladas por tarea de 8 horas y responde satisfactoriamente siempre y cuando las condiciones de las vetas lo permita.

Jul 20, 1957

By A. Halim, A. Martikainen, S. GYAMFI

This paper outlines a unique case of the development of strategies to reduce ventilation and heating costs in Konsuln iron ore mine in northern Sweden. The mine, located just south of Luossavaara-Kiirunavaara Aktiebolag’s Kiruna iron ore mine, was developed as a test mine from 2018-2020 for the Sustainable Underground Mining (SUM) project. Besides functioning as a test mine, Konsuln also contributes to ore production. The existing mine ventilation system was designed for the current production rate of 0.8 million tons per annum (Mtpa). There is a plan to increase this rate to between 1.8 and 2.0 Mtpa.

Sep 30, 2021

Near-Infrared Spectroscopy (NIRS) Sorting in the Upgrading and Processing of Skorpion Non-Sulfide Zinc Ore In 2008 Anglo American sponsored a research project at RWTH Aachen University to assess the feasibility of the use of near-infrared spectroscopy (NIRS) for ore waste discrimination at the Skorpion zinc mine. The Skorpion mine is an open pit zinc mine located in Namibia, owned by Anglo American with an annual production of 150 000 t/a of super high grade pure zinc. Opportunities for the implementation of NIRS sorting for the Skorpion process exist to upgrade currently subeconomic material, including the marginal dump (over 2000 000 tonnes, av grade of 2.5 per cent Zn). NIRS sorting is not yet implemented or established in the minerals industry however it is a proven technology in the plastics recycling industry, where more than 2000 NIRS sorters have already been installed. NIRS sorting, a type of sensor-based sorting, is a single particle sorting technique which classifies the particles based on the absorbed/reflected radiation in the near-infrared (NIR) region. A disadvantage of NIRS is that it is a surface measurement technique, but NIRS sorting shows overall great potential for the minerals industry. Skorpion ore minerals include zinc bearing phases such as sauconite, hemimorphite, smithsonite, and hydrozincite. These display diagnostic responses in the near-infrared. There are three major absorption features that characterise the reflectance spectra of the ore bearing minerals. These are due to OH and H2O molecular bonds. The spectral response of the waste material is caused by other minerals such as non-zinc-bearing clay minerals, calcite and impure quartz. Test work showed that it is theoretically possible to separate ore material from most waste material based on spectral response in the NIR region. In addition to upgrading material by removal of waste it is also potentially feasible to classify the material based on zinc grade. A tentative correlation between zinc grade and spectral response seems to exist for the sample test suite in the NIR region.

Sep 13, 2010

By Joel Moskowitz

In 1990, the United States General Services Administration (GSA) issued a contract for design and construction of a new federal court building in New York City. Mueser Rutledge Consulting Engineers (MRCE) served as Project Geotechnical Engineers. The project site is in the historic government district at Foley Square. It is surrounded by the New York County Courthouse to the west, an existing federal prison building and federal courthouse across Pearl Street to the south and southwest, an office structure to the north, and a residential tower to the east. The interior of the site was crossed by streets which have now been demapped. As with many urban sites, this site was previously occupied by tenement buildings or industrial structures demolished near the turn of the century. Remains of old building foundations were exposed during construction excavation. In addition, buried fuel oil tanks servicing the adjacent courthouse were removed and the usual assortment of urban utilities had to be relocated for the new building foundations. Ground surface elevations vary from about 4.5 to 6 m above the local Mean High Water Datum Plane.

Jan 1, 1996

By W. L. Brien, O&apos

Molybdenum alloys with good strength properties at elevated temperatures were produced by the powder metallurgical internal oxidation method previously applied to tungsten and known as oxyreaction strengthening. Commercial molybdenum powders were blended with 0 to 10 pet of a reactive powder, ZrMo2. The effects of composition, blending procedure, and sintering conditions on strength properties at elevated temperatures were studied. Strengthening was attributed to zirconium in solid solution with molybdenum and to the presence of submicrometer particles of Zr02. Several alloys had tensile strength and stress-rupture properties com-parable with those of the best commercial alloys. The maximum tensile strengths obtained were 92 kpsi at 1,200° C and 53 kpsi at 1,316° C. The maximum stress-rupture life at 30 kpsi and 1,200° C was 145 hours.

Jan 1, 1974

By Jerry E. Olson

In 1984, the U.S. Bureau of Mines conducted a mineral survey of the Pahute Peak Wilderness Study Area (WSA) (NV-020-621), which covers 57,529 acres in Humboldt County, NV. About 90 percent of the WSA is underlain by Tertiary volcanic and shallow intrusive rocks. Of the remainder, metasedimentary rocks of unknown age are in contact with Cretaceous intrusive rocks in the northwest corner of the WSA. The entire WSA is within an upthrown fault block of the Basin and Range physiographic province. Portions of the WSA, especially south of Pahute Peak (Big Mountain), may be part of an eroded caldera structure. No mines or evidence of major exploration were identified within the WSA. Workings in Copper Canyon, claim blocks along the northwest boundary, and zones of anomalous character as defined by the Bureau of Land Management were examined. No mineral resources were identified, but sample results indicate three significantly mineralized sites, one with indications for zinc skarns in Copppr Canyon, another favorable for precious metals 2 miles south of Copper Canyon, and another area near the northwest boundary with geologic conditions characteristic of molybdenum deposits. Further investigation of these sites is warranted. Petrified wood is present in small amounts near the west central range front.

Jan 1, 1986

By Georgios Kalamaras, Chiaia Dinu, Platania Paolo, Alessio Carlo, Giampiero Cirvegna, Claudio Santucci

The Project alignment initiates north of Pinerolo, along the State Road 23[S.S. 23] that is one of the principal arteries to the northwestern Alps where a number of Olympic events for the 2006 Winter Games will be held. The 3.5 km ring road bypasses the Porte habitat by traversing twice the Chisone River. It consists of the following principal structures [Figure 1]: San Martino bridge [130 m in four bays] Prarostino viaduct [130 m in four bays] Craviale tunnel [1055 m] Turinella bridge [a 50 m long bridge that connects the two tunnels] Turina tunnel [665 m] Malanaggio viaduct [350 m in 9 bays]. The road section is 13 m wide and is made up of two 3.75 m lanes, a hard shoulder [1.50 m wide] and a 1.25 m wide curb for each lane. The Project maximum velocity is 100 km/h.

Jan 1, 2005

By D. H. Mullen, S. M. Runke, J. B. Cunningham

"SUMMARYThe coarse-grained granitic pegmatities of the United States have long been a source of many important industrial minerals, because of this, they have been studied intensively by geologists, mining engineers, and metallurgists. These studies have amassed a rather astounding array of published and unpublished information.Correlation of geological studies between individual pegmatites, as well as between major districts, has brought forth some semblance of order to the knowledge of the structure and Mineralogical composition of those highly complex and irregular deposits, making it possible to classify certain prgmatitites and pegmatitec zones into several groups of associated minerals; based upon the presence or absence of the minor minerals of beryllium and lithium. This classification or grouping of minerals, with the methods that have been developed for recovering certain of these minerals, makes possible a systematic approach to the winning of many of the industrially important minerals from pegmatite rock by a single integrated process.As the coarse-grained granitic pegmatites are composed primarily of,feldspar, quartz, and muscovite, the methods developed for separating and recovering them, as well as those methods developed for separating and recovering such minor minerals as spodumene and lepidolite, are important contributions to the over-all problem of pegmatite treatment. Some of these methods have been demonstrated in the laboratory only, whereas others have progressed beyond the laboratory stage arid are being employed in commercial operations.Recent laboratory investigations at Rapid City, employing both these early developments and the mineral groupings, have demonstrated that a single integrated process can recover muscovite, feldspar; and. quartz from the rejects of hand-sorting a typical muscovite-feldspar-quartz material. Employing a newly developed procedure for the flotation of beryl, the investigations have also demonstrated the possibility of recovering the beryl, in addition to muscovite, feldspar, and quartz, by an integrated process from a typical berylliferous pegmatitic material in which all of these minerals are present."

Dec 1, 1952

By Dogan E. Gücer

In the following note, with the help of a new parameter of strain hardening, the attention is drawn to the close relationship between the relative performances of steels under plastic range cycling and their strain hardening characteristics. If a cantilever beam of rectangular cross section is tested with the arrangement shown in Fig. 1 in reversed bending between constant deflection limits at the lever head, the longitudinal strain-deflection hysteresis shown in Fig. 2 is obtained. There is no lateral strain due to constraint at the rectangular test section.' If the absolute value of strain undergone between a maximum state of tension and maximum state of compression is called A, it will be seen that A decreases with cycling rapidly due to the strain hardening in the test section and the ensuing change in the bent beam profile. It will also be seen that A reaches an approximately stable value around 10th cycle. If we call the first cycle strain range, A,, and that of 10th cycle, A,,, then is an index of the strain hardening capacity at a particular deflection level. A plot of n vs ? is reproduced in Fig. 3 for two ASTM steels: A-302 and A-201. A-302 is a low alloy structural steel, A-201 a low-carbon steel. The specimens were first normalized at 1650°F for 75 min then grooved with a milling cutter; and the notches were ground to 50G finish. The final operation before testing was a stress relief at 1150°F for 75 min. The behavior of the two steels changes around ?1 = 0.8 pct or A,, = A, -n = 0.7. If these curves are compared with the endurance life curves given in Fig. 4, it will be seen that the relative performance of the two steels also change around A,, =. 0.70 pct. The steel with lower strain hardening capacity (7) at a certain strain level shows a longer endurance life, irrespective of their strength levels. Since the exponent governs strain hardening at lower strain levels than the Modulus, the relative values of both parameters also coincide with the change in n values and the relative performances of the two steels at different strain levels. These two observations indicate to the close relationship be-

Jan 1, 1962

The Effect of Molecular Weight on the Adsorption and Efficacy of Polysaccharide Depressants

Sep 13, 2010

By Paul G. Swanson

This investigation was conducted to identify the principle causes of spoil instability problems in the Eastern Coal Province. The study was also conducted to develop a matrix to predict the strength and groundwater parameters necessary to conduct stability analyses on a proposed reclamation scheme. Suggestive methods to reduce spoil instability potential are also included. Numerous physical property, strength, compressibility, chemical and mineralogical tests were conducted on mine spoil samples obtained from 11 different surface mine sites. Site characteristics that influence the position of the post reclamation groundwater table were identified. Distinct regions within the Eastern Coal Province with high incidences of surface mine slides or high landslide susceptibility were identified. The application of the predictive matrices developed in this study is for surface mine sites mined and reclaimed in general accordance with the Surface Mine Reclamation Control Act of 1977. A review of current mining practices and the relative effect on spoil stability is included.

Jan 1, 1983

By A. P. Whittlestone, J. D. Johnson, R. J. Pine, M. E. Rogers

standpoint. The effect on efficiency of collisions

Apr 1, 1995

By G Wyartt

Systems such as Davey Bickford’s Daveytronic® SP blast initiation system and electronic detonators have been an integral part of drill and blast activities in Australia for over a decade, with the significant benefits of electronic blasting well documented. Since 2010 the Multiblast feature has been commercially available, which enables eight individual blast patterns (up to 1500 detonators each) to be blasted in the same firing window. Synchroblast has been in active operation since 2012, which allows a blast of up to 4500 detonators – either as a single blast pattern, or several smaller adjacent blast patterns – to be reliably initiated.Multiblast manages blasts separately but concurrently, allowing all blasts to conduct prefiring checks simultaneously from the firing point utilising only one remote blasting unit. Each blast can be selected and fired individually, in a sequence determined by the operator by scrolling through the colour display. Synchroblast automatically detects the blasting configuration, and manages all detonators as a single blast pattern. This simplifies the design and blasting processes for the mining operation.Multiblast and Synchroblast are routinely employed throughout Australia and globally in both open cut and underground operations, enabling optimal productivity due to increased blast volume and reduced operational downtime associated with blasting events.A number of case studies will be presented in this paper, detailing various mining operations that are consistently blasting in excess of 2500 detonators per blasting event as a part of standard drill and blast operations. Blasts over 3000 detonators are becoming more frequent as mine planning departments adapt to this operational capability and flexibility.CITATION:Wyartt, G, 2017. Multi and Synchroblasting – maximising operational productivity, in Proceedings Iron Ore 2017, pp 631–634 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Z. Lin, M. Isac, R. I. L. Guthrie

The kinetic and thermodynamic efficiencies of chromium recovery from the slag in an AOD process during the slag de-oxidation period with ferrosilicon is a complex process affected by slag basicity, temperature, the dissolution kinetics of the reducing agents, and intermixing of the slag/metal/alloy addition phases within the vessel. The present work focused on a study and simulation of the fluid dynamics and mixing behaviour of ferrosilicon additions in the AOD process for the production of stainless steel. In order to visualize the mixing behaviour, a two dimensional slice model of an AOD vessel was first built and filled with ZnCl2solution and then covered with silicone oil in order to represent the bulk liquid steel and slag phases, respectively. The injection of argon/oxygen process gases was simulated using air or helium. Particle trajectories and intermixing of the phases was monitored with a high-speed camera. To simulate the 75FeSi additions, glass spheres were used. A three-dimensional version of the AOD model was then constructed in order to confirm the adequacy of the slice model. Similar particle mixing behaviour was observed. Both models demonstrated that the ascending gas/liquid plume created two asymmetric mixing zones: a smaller rapidly re-circulating mixing zone adjacent to the side-wall locating the tuyere(s), and a larger mixing zone in the main part of the vessel. The process efficiency during the reduction period is governed by the thermal behaviour of ferroalloy as well as the mixing efficiency in the main large mixing zone. To enhance the recovery efficiency for chromium, small Fe-Si particles are suggested, given their wide distribution within the slag phase, and their large interfacial areas and rapid melting times for Cr2O3reduction from the slag. Keywords; modelling, ferrosilicon, chromium oxidation, AOD steelmaking.

Jan 1, 2004

By Harry Perry

One of the most notable achievements of the iron and steel industry in the United States in this century has been the general increase in productivity of individual blast furnaces and the reduction in coke rate. Most of the improvement in furnace operations has occurred within the past decade. During this time the output of the average furnace increased about one-third, while fuel rates decreased from 15 to 20 percent. For example, in 1949, the iron and steel industry produced 811.2 short tons of pig iron per blast-furnace day with a coke rate of 1,870.4 pounds per ton of pig iron, By 1960, the average production of pig iron per blast-furnace day had risen to 1,182.4 tons, while the coke rate had decreased to 1,497 pounds per ton of pig iron. These figures are averages for the entire industry; many furnaces produced over 2,000 tons per day and one furnace, operating on pellets, reached 2,700 tons of pig iron per day, Coke rates of individual furnaces varied, but some furnaces operated on less than 1,200 pounds per ton of pig iron. The significance of this decrease in coke rate is shown clearly when data on pig-iron production and coke consumption in 1959 are compared with 1948. In 1948, 57.3 million short tons of coke was charged into blast furnaces to produce 60.1 million tons of pig iron; in 1959 only 47.6 million tons of coke was needed to produce 60.2 million tons of pig iron. Thus, in 1959, nearly 10 million tons less coke was required to produce about the same amount of pig iron as was produced in 1948.

Jan 1, 1962

By J. P. Josien, Didier C.

ABSTRACT: France now faces the closure of most of its mining sites. Surface instability risk may sometimes remain, especially where large underground voids exist. This paper illustrates the importance of failure mechanisms identification in order to define properly how to manage the residual risk. RESUME: La France fait aujourd’hui face à la fermeture de ses exploitations minières. Des risques d’instabilités de surface peuvent persister, notamment lorsque des vides résiduels existent au sein des travaux souterrains. L’article illustre l’importance que présente la nature des mécanismes de rupture potentiels dans le choix des mesures compensatoires à adopter pour gérer le risque résiduel à long terme. ZUSAMMENFASSUNG: In Frankreich stellt sich derzeit das Problem der definitiven Schliessung des meisten Bergwerke. In manchen fällen ist die Stabilität der Oberfläche nicht garantiert, speziell wenn unter Tage nicht verfüllte Hohlräume verblieben sind. Dieser Bericht zeigt die Wichtigkeit, bei der Auswahl geeigneter Langzeit-Risikomanagementmethoden, der verschiedenen Mechanismen mit denen ein eventueller Bruch an die Tagesoberfläche geraten kann.

Jan 1, 2003

The Johnny Mercer lyrics 'You've got to accentuate the positive, Eliminate the negative, Latch on to the affirmative à' would best sum up the traditional approach to community relations in the mining industry. This '90s 'Public Relations spin' approach, usually backed up by scientific data, technical reports and graphs outlining risk probability and the impact potential on people and communities, is being challenged. Challenged by communities who have greater access to information, demand greater levels of transparency and corporate responsibility of large corporate operations and possess greater awareness of the communities they live in.   The growth of the environmental movement, of anti-globalisation, anti corporatism, apprehension of a large corporate's ability to deal with community issues, and a lack of faith in the abilities of regulators to regulate corporate activities, means our industry faces challenges on multiple fronts. It must now be able to address these from a personal/community perspective if it is to remain relevant within communities.   One of the keys to this is linking the internal activities and responsibilities to the externals concerns and demands for higher levels of operation and care.   This presentation draws on Corporate Public Affairs trends, functions and approaches and the application to External Affairs activities within Newmont Waihi Gold's operations in Waihi and regional exploration activities throughout the Hauraki Goldfields.   The approach presented works on the philosophy that communities don't necessarily have to like what we do, but should be able to identify and recognise the way in which we involve them in decision making, communicate our intentions and respond to issues.

Jun 1, 2010

By Gavin C. Dirom

? The Mining Association of British Columbia (MABC) was established through an Act of Parliament in 1901 ? The MABC represents the interests of B.C.?s ? Coal and mineral mining companies ? Smelting companies ? Advanced stage development projects ? Key areas of work: ? Environment, Health and Safety ? Policy & Government Relations ? Knowledge and Information Services

May 1, 2008

By Oscar Lee, B. W. Gandrud, F. D. DeVaney

"IntroductionFlue dust which results from the smelting of ores containing appreciable quantities of fines is one of the troublesome products of iron blast-furnace practice. Gases issuing from the furnaces at a high velocity carry small particles of coke, ore and flux into dust-collecting chambers. These particles constitute the flue dust. Lasses of iron ore through the production of flue dust vary between wide limits in the different furnaces, and depend on a number of factors, such as size and design of furnace, amount of fines in the ore, the operating conditions and the blast pressure.Blast-furnace operators of the Birmingham district keenly realize this waste. The ores are comparatively low grade and require more fuel than is ordinarily used elsewhere. Hence the flue dust is low in iron content and high in coke. As a result it is not in suitable condition for direct sintering. In many other iron and steel centers direct sintering is a common practice. In the Birmingham district efforts have been made to prevent this loss by recharging the dust into the furnace, but, as might be expected, a material fine enough to be blown out once will very likely be carried over again.In general, the flue-dust losses in this district will average 250 pounds per ton of pig iron produced, but at times the losses at different furnaces are substantially higher or lower than this figure. On the basis of the present rate of pig-iron production, the annual loss of flue dust exceeds 300,000 tons. The iron content of the dust probably averages 25 per cent, therefore about 75,000 tons of iron is wasted yearly, or about 3 per cent of the iron mined is lost in flue dust."

Jul 1, 1926