Search Documents

Pilot-Plant Testing of Ammoniacal-Cyanidation for Gold Recovery from Copper Gold-Bearing Ore The results of pilot-plant tested ammoniacal-cyanidation of gold recovery from copper gold-bearing ore are presented in this paper. This ore is from a deposit of Russian Federation with gold and copper grade 9.5 g/t and 0.4 per cent, respectively. Copper is largely present as malachite and azurite. The presence of chalcopyrite and bornite is also observed. In order to recover gold, gravity is recommended. Two options of ammoniacal-cyanidation using leaching of gravity tails, CIP and filtration, were tested. It was found that ammoniacal-cyanidation using filtration of leaching tailings and recycled solutions is the most optimal option. The proposed flow sheet provides for 89.7 per cent gold recovery from gravity tailings at the consumption of NaCN 0.9 kg/t and (NH4)2CO3 7.5 - 9 kg/t. Compared to conventional cyanidation, this technology decreases the consumption of sodium cyanide from 4 up to 0.9 kg/t at the same gold recovery. It can be recommended for the treatment of copper gold-bearing ores with the similar composition.

Sep 13, 2010

By Yang Jun, Qu Mei, Zheng Yao-wu, Chi Li-yuan

Due to the necessity of the prediction of blasting seismic effect around strip mine bench blasting area, the paper provides a method to predict the blasting seismic effect by employing the superposition of seed waveform at different monitoring points. The method assumes that blasting vibration waveform per hole is similar to seed waveform at monitoring point. Therefore seismic wave consists of the superposition of the waves from all of blast holes. Firstly, via sensors multiple seed waveforms can be achieved at different distances from signature hole. Then, by using the given dose and the distance, the vibration waveform of a certain blast hole can be calculated by the corresponding seed waveforms. Finally, the initiation delay time interval per hole is added to the propagation time to the predicting point. The predictive waveform at the whole blasting area can be obtained by superimposing all of the single waveforms. Considering the vibration waveform of a single blast hole changes greatly with the distance, under different distances condition the seed wave employed to superimpose is achieved from the similar distance. The experiments demonstrate that based on the method the predictive vibration waveform and spectrum are basically consistent with monitoring results around near-field blast. Compared with single seed wave method, the superposition method of multiple seed wave is more reliable to predict the duration of blasting vibration, the peak particle velocity, dominant frequency and frequency distribution.

Jan 1, 2015

By J. S. Dunning

One Federal Bureau of Mines research goal, to minimize requirements for domestically scarce mineral commodities through conservation and substitution, can be accomplished by utilizing more abundant elements such as iron, molybdenum, and titanium. An example of this research is the study of precipitation-hardening, iron-base alloys containing molybdenum and titanium, as substitutes for the high-tonnage stainless steels that are high in imported nickel and chromium. The precipitation hardened iron-base alloys are strengthened by a dispersion of the ternary Laves phase, Fe2 (Mo, Ti). Aluminum and chromium additions changed the solid solubility limits of molybdenum and titanium in a-iron and affected the composition of precipitating phases. A baseline composition of Fe-7Mo-2Ti was selected to study the effects of aluminum and chromium additions on the precipitation-hardening mechanism and microstructure and was also used in studies of mechanical properties and oxidation resistance. The study yielded workable, precipitation-hardening alloys, with elevated temperature strengths equivalent to or superior to types 304 and 316 stainless steels. Chromium and aluminum additions in combination were more effective in providing oxidation resistance than either addition was alone.

Jan 1, 1980

By Iman G. Ghanad

El presente texto describe un nuevo método para el tratamiento de concentrados de cobre con alto contenido de arsénico utilizando el carbón activado como catalizador. Para ello, se realizaron pruebas de lixiviación con concentrados de enargita de tres minas de Chile, Perú y Estados Unidos, donde los resultados señalaron que la disolución de la enargita fue más rápido con la influencia del carbón en la solución lixiviante, incluso después de haber reciclado el carbón.

Sep 12, 2011

By Thomas E. Finch

This report is a continuation and expansion of a previous USBM grant (No. G0254004) which examined alternative methods of handling the parting between two coal seams in a surface mining operation. The alternative methods consist of equipment implementation in either a stowing or haulback technique. Following a typical strip mine conformation, the parting is directly stowed or hauled back and placed in the pit bottom after second seam removal. The objectives are to produce an environmentally sound material placement technique and to increase prime stripping machine utilization. This report contains the engineering philosophy behind two computer programs created to evaluate parting handling methods over d wide range of coal and parting thickness ratios. The nature of the computer approach allows cost sensitivity analysis and quick updating of costs. The two programs are clearly presented with documentation and examples such that consumers may apply then to their own operations.

Jan 1, 1977

By James A. Schneider

The evolution of the American Petroleum Institute (API) design method for axial capacity of driven piles in siliceous sands is explored, and complemented with an overview of how changes in offshore site investigation practice have increased the level of knowledge with respect to vertical variability of soil characteristics. Increased use of the cone penetration test (CPT) provides near continuous profiles of soil type and strength which can be used in calculation methods that address variation in local shaft friction rather than the API method which seems to have initially been based on observations of average shaft friction in relatively uniform sand deposits. Development of a formulation for CPT correlations to axial pile capacity in sand is discussed, along with implications to existing factors of safety used in routine design.

Jan 1, 2006

By C. Dixon

This paper is based on the assumption of some knowledge of the National Water Act. It will consider the question of how that Act fits in with: a) existing laws which overlap on the subject matter b) new laws either in draft or in the process of being compiled c) policies which will eventually find their provisions included in new legislation (e.g. minerals policy) d) international practices. The focus will be specifically on the interaction of legislation relating to water use and water pollution in the mining sector as well as the role of the Department of Water Affairs in mining matters. Hence the title of the presentation.

Jan 1, 1999

With a price slowly rising above US$35 per ounce gold became a mineral worthy of prospecting and mining endeavour in the early to mid 1970s. Fortune therefore appeared to smile onNew Zealand with its favourable geological environment for gold and past record of major gold production from both hard rock and placer deposits. This was a particularly welcome development as the post war years, including both the base metal exploration boom of 1967/1971 (which produced major nickel, iron and bauxite mines in Australia) and the earlier period of uranium exploration failed to produce any mines in New Zealand with the exception of the small Tui Mine and iron sand mining. Whilst hard rock mining now appears imminent it is 15 years further along the track since the 1967/1971 exploration boom and eight years since the upsurge in prospecting for gold in 1978. New Zealand still has no hard rock base or precious metal mining. This is not for want of proven or potential gold mining situations for these clearly exist at Waihi, Monowai Reef, Golden Cross, MacRaes Flat and elsewhere.

Jan 1, 1986

With increasing demand for real-time monitoring of mine parameters, the requirement for appropriate data management in many mining applications is also increasing. This includes atmospheric monitoring in underground coal and metal mines. Although a number of different (real-time) monitoring systems have been installed in underground mines, they all typically share the same systems or sub-systems, where each sub-system may include both custom hardware and / or software components. In addition, monitoring components installed in underground coal mines in the USA should also be intrinsically safe and approved by the US Mine Safety and Health Administration. Real-time analysis adds complexity to the system since data validation and storage should be completed independently of filtering, data reduction operations, or visualization. Real-time processing may include statistical evaluation, trending, cross-correlation, and real-time alarm or warning generation. This paper presents the concept and design of an integrated system under development for atmospheric monitoring in US coal mines.

Jan 1, 2014

By E V. Kislov

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Northern Baikal Ni-Cu province is located in Buryatia, south-east Siberia, and geologically is part of the Baikal-Muya volcano-plutonic belt. It is known for numerous PGE-Ni-Cu-bearing mafic-ultramafic intrusions of Neoproterozoic age formed in various geodynamic settings. All these deposits can be regarded as a single Ni-Cu ore cluster located near the Kholodninskoe Pb-Zn deposit, which is ready for mining. In addition, there are less studied, small dyke-like bodies with sulfide mineralisation that formed in a rift setting and may be enriched in Ni, Cu and PGE. Individually, the known bodies are of poor commercial value by their resources, but their close spatial association (<30 km) may make these PGE-Ni-Cu deposits economic in the future. This extended abstract seeks to provide a geological framework of the North Baikal Ni-Cu-PGE province, specifically at the north-eastern Synnyr rift hosting numerous small subvolcanic bodies with Ni-Cu sulfide mineralisation. Some small subvolcanic bodies contain industrial level Ni-Cu deposits (Shanuch, Cabanga-Musongati, Voisey’s Bay, Jinchuan, etc).CITATION:Kislov, E V, 2015. North Baikal region Ni-Cu deposits , in Proceedings PACRIM 2015 Congress, pp 297–302 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Jeffrey Whyatt

Mining coal in deep, gassy strata is difficult, particularly in deep mines of the west. Dynamic failure (bumps, bounces, etc.) is commonplace, particularly where strong sandstone strata are encountered in the overburden. The disaster potential posed by dynamic failure in these mines is examined and found to be significant. Recent trends in MSHA reportable bumping of deep western coal mines have been increasing. Recent clusters of bumps are explored, a number of which have ended badly. The mechanisms of these bumps and their interactions with geologic structures are explored. Significant progress in controlling these hazards depends on a full understanding of their interaction with geologic conditions. It is apparent that not all MSHA reportable bumps have the same mechanism. These reports describe bumping of pillars, rolling of ribs, outbursts of coal, heaving of floor, shaking-induced roof falls, etc. Progress depends on understanding the underlying mechanisms of these events, and then determining which are potentially active at a particular location. Designs and other protective measures can then be adapted and deployed appropriately. Explicit consideration of mechanisms also supports extrapolation beyond experience as design extends into new mine geometries, geologies, mining methods and increasing depth. Finally, the goal should not be only to design hazard out of mines, but also to provide assurance that this, in fact, has occurred. Pursuit of this goal has been taken up by a major NIOSH research project. The centerpiece of this project is development of a Dynamic Failure Control Program to monitor evolution of dynamic failure hazards with changing geologic conditions to assure that control and protective measures are appropriately deployed.

Jan 1, 2008

By M. John Brodie

This report reviews the regulatory environment as it pertains to waste rock management and disposal from mining operations, excluding coal and placer gold operations, in the \irate of Alaska. It is based on the EPA's staff position on an effective program to regulate mining waste as presented in the May, 1990 Strawman II document. The unique conditions which occur in pans of the state, including a fragile environment, high seismicity and permafrost, are identified. The special waste management practices which are necessitated by these conditions are delineated. The report provides a detailed outline of the current technologies that are suitable for designing, constructing, operating and closing a waste rock facility to meet environmental protection objectives. Cost implications to the mining industry of potential regulatory actions, such as the degree of groundwater protection, are examined.

Jan 1, 1992

By I. Dimitrov, S. R. McCutcheon

"Industrial-grade limestone is found in both the Lower Silurian La Vieille Formation and Upper Silurian LaPlante Formation of the Chaleurs Group in northern New Brunswick. Currently, between 150 000 and 200 000 tonnes of limestone are produced per year from the proximal facies of the LaPlante Formation at the Sormany quarry of Elmtree Resources Ltd., located west of Bathurst.The proximal facies of the LaPlante Formation was deposited on the margins of tectonically uplifted Ordovician terranes. This facies comprises stromatoporoidal-algal bindstone intercalated with wackestone, packstone, and floatstone in variable proportions. The distal facies comprises calcareous shale and minor limestone deposited deeper offshore.Folding and faulting related to Middle Devonian Acadian tectonism have caused an increase in the apparent thickness of the limestone sequences, especially adjacent to the regional Rocky Brook-Millstream fault. Structural and stratigraphic observations indicate that some of the limestone bodies in the area have been tectonically displaced from their site of deposition.A variety of prospecting techniques was used to locate new limestone resources, including geological mapping, airborne and ground electromagnetic surveys, and satellite remote sensing. Clastic rock units above and below the LaPlante Formation have distinctive properties that help to trace the intervening limestone along strike. Because of water-saturated glacial cover, thick vegetation, and the small size of targets, airborne geophysical methods did not prove effective in delineating limestone beds, but aeromagnetic surveys helped map the underlying clastic unit. The remote-sensing data and especially high-resolution digital elevation models helped in identification of karst topography related to limestone."

Jan 1, 2007

Nautilus Minerals and Neptune Minerals are betting that the next great metals rush will take place more than 1,500 m (5,000 ft) below the sea. Nautilus is the first company to commercially explore the ocean floor for gold and copper seafloor massive sulfide (SMS) deposits. Its main focus is the Solwara 1 Project, a polymetallic copper, gold, zinc, silver deposit that is under 1,600 m (5,200 ft) of water off the coast of Papua New Guinea in the western Pacific Oceans? Rim of Fire. Nautilus Minerals, in a joint venture with Placer Dome (now Barrick Gold), began its exploration of what would become the Solwara 1 area in 2005 with side scan sonar and dredge sampling. The dredge and grab sampling confirmed the grade tenor of earlier sampling by scientific research programs. The 45 dredge samples aver-aged 10.8 percent copper, 3.7 percent zinc, 224 g/t (6.5 oz/st) silver and 13.7 g/t (0.4 oz/st) gold. Nautilus has since staked out more than 300,000 km2 (115,800 sq miles) of tenement licenses and exploration applications in the waters off Papua New Guinea, Fiji, New Zealand, Tonga and the Solomon Islands. That is an area about the same size of the United Kingdom. Interest in Nautilus and its projects has grown tremendously since its inception. The company is now listed on the Toronto Stock Exchange. It has raised more than $300 million and spent more than $23 million on exploration. The company has gained the backing of mining majors such as Teck Cominco, Epion, Anglo American and Barrick Gold. It is positioned to become an emerging producer in 2010. Teck Cominco recently agreed to exercise share purchase warrants to acquire three million additional common shares of Nautilus at a price of US$15 million. This will take Teck Cominco?s shareholding to approximately 7.2 percent of the issued shares. Teck Cominco will conduct and manage a ship-based exploration program that will run in addition to the exploration that was already planned for 2008.

Jan 1, 2008

By C. A. Pickles, J. M. Toguri

The refining of two molten Ag-Cu alloys, containing 7.5 and 11.2 mass% Cu, with a borosilicate slag was investigated using both air and pure O2 to determine the effects of the following variables: flow rate of oxidising gas; injection time; mass of sodium borosilicate flux; and injection of the oxidising gas into either the slag or the metal. The results demonstrate that more than 90% of the Cu can be removed with Ag losses of less than 5% and that refined metal with a Cu content of less than 0.5 mass% can be produced. Ag losses to the slag increased with the amount of Cu removed, and a mechanism is proposed to account for this

Dec 1, 1995

By William E. Lardner

Interlocking caisson walls developed from conventional "soldier pile and lagging" shoring. In the latter, the soldier piles receive directly most of the soil load. Natural arches form in the soil behind the shoring; the lagging supports little more than the segment of soil inside the arch. Fig. 1: A typical layout of a lagged wall [ ] Fig. 2: A typical layout of an interlocking caisson wall [ ]

Jan 1, 1987

By Walter B. Lenhart

This paper is one of a series on milling methods and costs being. published by the Bureau of Mines. The milling practices and special problems relating to grinding, tailings disposal, and choice of a treatment process at the Cardinal mill are discussed. The property of the Cardinal Gold Mining Co. is about 18 miles southwest of the town of Bishop, Inyo County, Calif., at an altitude of approximately 8,500 feet. The camp has been designated Bishop Creek by the postal authorities. The property comprises 33 mining claims, including fractions and millsite in sections 19, 20, 29, and 30, T. 8 S., R. 31 E. These claims are located in a general way along the strike of a band of quartzite.

Jan 1, 1938

By J. F. Barkley

To aid in winning the recent world war, the Bureau of Mines conducted a National Fuel Efficiency Program, directed to commercial plants throughout the Nation, to save greatly needed fuel, a basic resource vital to industrial production. In planning this program it was realized that to accomplish a satisfactory reduction in fuel consumption in any plant, it would be necessary to reach, enthuse, and usually educate to some extent the actual operators of the various types of plant equipment. A major part of the programs consisted, therefore, of visits to plants and work with the operators, including a review with them of their operating conditions and of educational and guiding literature pertinent to the operating problems involved. Through a Nation-wide organization, local volunteer engineers served in making visits to local plants. Each cooperating plant appointed an employee as the "waste chaser," who headed the work of saving fuel in that plant. The educational literature was designed to interest the operator, as well as serve as a guide in eliminating waste of fuel. Volumes have been written on many subjects relating to the saving of fuel. Writings of the treatise type contain considerable good information but do not have wide appeal and probably will be read only by a few studious operators. The problem is not one of getting clown on paper everything that the experts know and would like to have the operator know, but rather to write something that will actually interest the operator and stimulate him to action. Past experience led to the adoption, therefore, of the "quiz-sheet" type of writing, using a quiz sheet of not more than two pages for any principal item. The results obtained during the National Fuel Efficiency Program in many types of plants further demonstrated that the short quiz sheet is satisfactorily appropriate and does accomplish results. Each sheet was prepared and checked by many engineers expert in the particular subject matter of the sheet. Committees of men with much experience in the manufacture and operation of equipment and in the

Jan 1, 1947

By 12670

The Cigar Lake project will develop the world’s second largest high-grade uranium deposit. The Cigar Lake Phase 1 orebody contains approximately 226 million pounds U3O8 at an average grade of 20.7% U3O8. The mine, to be operated by Cameco Corporation, will use a unique water jet boring mining method to cut previously frozen ore. A distinctive ore handling design is required to handle the highgrade ore slurry exiting the mining machines. The ore will be crushed and ground underground, with the ore slurry then pumped to surface. Loaded into purpose-designed containers on tractor-trailer units, the ore slurry will be trucked to Cogema Resources Incorporated’s McClean Lake mill. McClean Lake will leach all of the ore. Forty-three percent of the resulting uranium solution will remain at McClean Lake for processing into yellowcake. The other 57% of the uranium solution will be shipped to Cameco’s Rabbit Lake mill for processing into yellowcake there. Detailed design for the Cigar Lake project is now underway. Barring regulatory or market delays, production could start up as soon as early 2006.

Jan 1, 2004

By Jacques Deraisme

The technology of percussion drilling is well mastered. The lower cost of percussion drilling allows more holes to be drilled for the same budget. However significant differences are often observed between percussion and diamond drill assay data. This is due to the increased level of contamination associated with the percussion drilling process. Statistical studies on twinned drillholes show that diamond and percussion assays cannot simply be merged in a traditional kriging approach. The question then arises on how to use both types of data to produce reliable resource estimates. To take into account the lower reliability of the percussion assays, a noise characterized by a variance is added to these data. The methodology consists of two steps: 1. Cokriging of the equivalent diamond value at the percussion assay locations. 2. Block kriging using diamond assays and equivalent diamond values, calculated previously, adding to these data a noise, whose variance is the cokriging variance of step 1. This particular way of achieving kriging is called kriging with variance of measurement error. The paper illustrates this innovative methodology with an application on an iron deposit. The results of this method is compared to block kriging using only diamond assays and the gain in precision is quantified. An extension of that approach to multi-element cokriging is also presented.

Oct 1, 2009