Search Documents

By O. K. Olawale, G. O. Edaogbogun, B. N. Ben‑Festus, F. Ben, F. R. Amodu

The environmental and health implications of artisanal gold mining activities at mining sites across Nigeria have rekindled research interest. This study aimed to assess the scalability of naturally occurring radioactive materials in gold mining sites in Iperindo, Nigeria. Soil samples were collected from three different mining sites and control locations and analyzed for natural radionuclides, mainly 238U, 232Th, and 40K, using gamma spectrometry having a sodium iodide detector. The average activity concentration values of 61.55 ± 3.71, 72.65 ± 4.45, and 1134.99 ± 38.12 Bqkg− 1 obtained from within the mining sites for 238U, 232Th, and 40K, respectively, were above the world permissible values of 33.0 Bqkg− 1 for 238U, 45.0 Bqkg− 1 for 232Th, and 420.0 Bqkg− 1 for 40K. The average activity concentration values of 15.26 ± 3.19, 21.46 ± 4.27, 381.04 ± 23.36 Bqkg− 1 estimated for 238U, 232Th, and 40K, respectively, for the control location were, however, lower than the global permissible values. The study also evaluated other radiological parameters such as radium equivalent, dose rate, annual effective dose rate, internal and external hazard indices, and alpha and gamma indices. The obtained values were 252.83 Bqkg− 1, 119.98 nGyh− 1, 147.15 mSvy− 1, 0.85 Bqkg− 1, 0.68 Bqkg− 1, 0.31 Bqkg− 1, and 1.89 Bqkg− 1 respectively. Except for radium equivalent, external and internal hazard risks, and alpha index, which were significantly lower than the recommended threshold, all other radiological parameters were higher than the recommended global limits. Moderate data reproducibility and a p-value of 0.000574 further reinforced the robustness and reliability of the results obtained in this study.

Feb 22, 2024

By Rob Domotor

This paper tells the story of using controlled surface and underground blasting methods to excavate hard rock in three areas on Australia’s largest road infrastructure project; the Airportlink Project in Brisbane; worth a total value of AUD $4.8 billion. The project used blasting methods including design, modelling, drilling and loading of the explosives that had never been used before in Australia, some of these were probably unique in the world.

Jan 1, 2012

By Christopher Mark

"Many problems in rock mechanics are limited by our imperfect knowledge of the material properties and failure mechanics of rock masses. Mining problems are somewhat unique, however, in that plenty of real world experience is generally available and can be turned into valuable experimental data. Every pillar that is developed, or stope that is mined, represents a full-scale test of a rock mechanics design. By harvesting these data, and then using the appropriate statistical techniques to interpret them, mining engineers have developed powerful design techniques that are widely used around the world. Successful empirical methods are readily accepted because they are simple, transparent, practical, and firmly tethered to reality.The author has been intimately associated with empirical design for his entire career. But where his past papers have described the application of individual techniques to specific problems, the focus of this paper is the process used to develop a successful empirical method. A six-stage process is described:1. Identification of the problem, and of the end users of the final product2. Development of a conceptual rock mechanics model, and identification of the key parameters in that model3. Identification of measures for each of the key parameters, and the development of new measures (such as rating scales) where necessary4. Data sources and data collection5. Statistical analysis6. Packaging of the final productEach of these stages has its own potential rewards and pitfalls, which will be illustrated by incidents from the author’s own experience. The ultimate goal of this paper is to provide a new and deeper appreciation for empirical techniques, as well as some guidelines and opportunities for future developers."

Jan 1, 2015

By Hwasoo Park

Keywords: FC mold, Argon, Magnetic, Solidification Fluid flow plays a significant role for steel surface quality in continuous casting. Although water models are able to model fluid flow, the flow pattern is not of practical interest since the moving solidifying shell cannot be accounted. Computer modeling has become a popular and dependable tool to analyze the complex phenomena occurring in continuous casting. In this numerical simulation we coupled momentum and energy equations considering the solidification of steel along with turbulence ?-e model. The vertical bending mold is equipped with bifurcated nozzle with 15 degrees of port angle. FC mold is supplied with DC induced magnetic fields. Influence of argon and magnetic fields on molten steel flow and heat transfer is investigated by solving momentum equations adding source terms due to multiphase ? magneto hydrodynamics. The results show that magnetic fields reduce the jet velocity from port by lower magnetic core induced field but the influence on meniscus velocity is complex to describe. Magnetic fields increase surface temperature and homogenize its distribution on surface and inside a mold.

Jan 1, 2005

By Keith D. Rosbury

The basic objective of this project was to determine the cost-effectiveness of dust control used on unpaved mine haul roads. Field testing was conducted at three surface coal mines (two in Wyoming, one in southern Illinois) for a total of 20 weeks. The highest control efficiency measured for a chemical dust suppressant, 82 percent, was for calcium chloride two weeks after application. Generally, however, the control efficiencies hovered in the 40 to 60 percent range over the first two weeks since application, and then decreased with time. After the fifth week, the limited number of data points suggest a control efficiency of less than 20 percent. Composite watering data were fairly uniform. Watering once per hour resulted in a TSP control efficiency of approximately 40 percent. Doubling that application rate increased the control effectiveness by about 15 percent to 55 percent. Chemical dust suppressants (primarily salts and lignons) can be shown to be more cost-effective than watering under some conditions. Data summaries and the analysis of data are contained in Volume I. Volume II contains basic data.

Jan 1, 1983

By Lever R. R

The paper discusses assay methods generally used when prospecting for gold, and also the applicability of various chemical methods, it describes a new paper chromatographic technique.for making fairly rapid semi-quantitative assays for very fine gold. Testing of the method in field work shows that this simple method could have applications in geologic work, in prospecting and in certain routine mine sampling work. It is not yet a method that can be used to detect anomalies in traces of gold dispersed around an orebody, as is general practice in geochemical prospecting.INTRODUCTIONAccording to the English economist Harrod (1958), "the acute shortage of gold in the world-because currency value has not been adjusted in line with the fall in the goods value of the various currencies-has been a familiar fact for some time now". Harrod calculates that a rise in the price of gold to double its present value is necessary to rectify this condition, and that, if this rise were to take place, increase in production and reduction in private hoarding might well bring annual accretion to world stocks from the presentaverage of about $464 million to a figure close to the $2,000 million that would probably eiiminate these shortages.Any increase in the price of gold is bound to lead to a great increase in prospecting at working mines, in abandoned areas and possibly in untouched country. Prospecting, techniques for base metal orebodies have improved greatly in the last thirty years; but methods available to detect gold occurring without accessory metals have not received the same attention. With this in mind a paper chromatographic method of assaying for gold has been developed by Lever (1958). In the field this semi-quantitative method has proved...

Jan 1, 1959

The Canadian concept for nuclear fuel waste disposal is being assessed by AECL Research in a series of experiments at its Underground Research Laboratory (URL) near Lac du Bonnet. Manitoba, Canada. As pan of this research, the Mine-by Experiment has been designed to obtain information on rock mass behavior, the development of an excavation-induced damage zone and failure mechanisms around a circular bored tunnel. An iterative design approach was used to effectively reconcile the experiment objectives and construction logistics. This paper discusses the design considerations and construction methodology adopted on the project.

Jan 1, 1991

By M. J. Collins

"Autoclaves were first used in the metallurgical industry in 1893 to recover alumina from bauxite. In the 1940s and 1950s, several high temperature and pressure processes were invented in the laboratory of Professor Frank Forward at The University of British Columbia, in parallel with advances in equipment and processes by the Chemical Construction Corporation. Sherritt Gordon Mines Limited enlisted these groups to help develop the nickel sulfide ammonia leach process that was commercialized in 1954. Autoclave processes that have since been commercialized include high-pressure acid leaching of laterites, zinc pressure leaching, and pressure oxidation of refractory gold feedstocks. RÉSUMÉ En 1893, l’industrie métallurgique est la première à utiliser les autoclaves pour l’extraction de l’alumine dans la bauxite. Dans les années 1940 et 1950, plusieurs procédés à haute température et à haute pression sont inventés dans le laboratoire du Pr Frank Forward de l’université de la Colombie-Britannique (UBC) ; parallèlement, la Chemical Construction Corporation fait de grands progrès en matière d’équipement et de procédés. Sherritt Gordon Mines Limited fait appel à ces groupes pour qu’ils aident la société à développer le procédé de lixiviation du sulfure de nickel dans de l’ammoniaque, commercialisé en 1954. Les procédés de lixiviation en autoclave commercialisés depuis incluent notamment la lixiviation acide à haute pression de latérites, la lixiviation sous pression du zinc et l’oxydation sous pression des matières premières de l’or réfractaire.INTRODUCTION Autoclaves are chemical reactors that are built to contain processes taking place at elevated pressure. They are used in metallurgical refineries throughout the world to take advantage of the increased reaction kinetics and different reaction products that can be obtained in aqueous systems above the boiling temperature at atmospheric pressure. The word autoclave comes from the French “auto” and the Latin “clavis” and literally means self-locking—that is, the core distinguishing feature of an autoclave is that it includes a means for pressure regulation (e.g., a pressure relief valve). Denis Papin (Figure 1a), one of the inventors of the steam engine, was the first to make use of a safety valve to control steam pressure. He is credited with inventing the autoclave in 1679. Papin’s “digester” (Figure 1b) was a type of pressure cooker that was originally used to liquefy bones. Most commercial autoclaves are horizontal, multicompartment vessels with mechanical agitation, as shown in Figure 2a; however, the steam-agitated Pachuca vessels used to leach laterite ore in Moa, Cuba (Figure 2b), are also classified as autoclaves according to the self-locking definition provided above."

Jan 1, 2018

By Lawrence H. Van Vlack, Alfred S. Keh

The distribution of sulfur in iron was found to be dependent upon the time and temperature of the treatment as well as the chemical composition of the sulfide. With higher temperatures, the sulfide phase spreads more extensively between the iron grains. A complete network, however, does not form until approximately 1300°C (2372°F), ot which temperature the dihedral angle approaches zero. Silicon has little effect on this change. Aluminum, oxygen, and manganese all modify the temperature of sulfide network formation to a higher value. The microstructures which result and have significance in relation to hot-shortness are discussed. SULFIDE inclusions in steel were recognized by metallurgists before the turn of the century. Considerable attention has been paid to them, and numerous studies have been made on the working properties of steel as affected by them. It has been suggested that ho t-shortness of steel is due to the presence of an enveloping liquid sulfide film at the grain boundaries of the steel in the range of the hot-working temperatures. However, several facts have been observed in commercial steels which do not seem to be completely consistent with this explanation: 1) the frequent absence of continuous films of sulfide as observed under the microscope, 2) the absence of hot-shortness in some high sulfur and resulfurized steels, and 3) the limitation of hot-shortness to a definite temperature range. The role that manganese plays in steel to eliminate hot-shortness is well known, but the theory behind it is still under question. Moreover, the effect of de-oxidizers such as aluminum and silicon, and the effect of oxygen are still not clearly known. In this study, the effect of heat treatments and of additions of manganese, aluminum, silicon, and oxygen upon the distribution of sulfide inclusions in iron was investigated. Both the as-cast and the heat treated structures were studied, using microscopic and autoradiographic techniques. Part of the results were interpreted in terms of Smith's' concept of microstructure. Review of Literature Metallurgists used to consider sulfide inclusions as suspended particles. It was Wohrman' who first pointed out that sulfide inclusions are soluble in liquid iron. Many observed facts may be understood on the basis of this concept of solubility. Wohrman found that small castings contain small inclusions. and larger castings contain larger ones. Also, inclusion sizes are smaller near the chilled surface. For the same size ingot, the average inclusion size in a given heat of steel depends upon the rate of solidification. That is, with slow solidification, enough time for precipitation and agglomeration of these

Jan 1, 1957

By H. Boghosian

This paper presents the design and construction of a deep basement in a steeply sloping site in glacial till in Glasgow city centre. Existing foundations, adjacent structures and services, in tandem with asymmetric loading, presented particular challenges in the planning, execution and design of the project. The construction methods and temporary works, analysis by the Finite Element method and monitoring carried out are all described.

Jan 1, 2006

By Primak. George J.

"In the development of a new product as well as during its introduction on the market, it is very important to give due consideration to problems involving patents, licenses and trade marks. At the very beginning of the research and development program, it is obviously essential to ascertain, through a suitable patent search, that the product in question will not infringe any patents which are still in force. Then, a possibility of achieving one's own patent or proprietary position on the product or the process of its manufacture should be carefully explored. Licensing arrangements that one may reach with respect to patents and know-how covering such new product may, in the final analysis, determine its over-all success or failure. If one can count on licensing revenues or some favourable cross-licensing arrangements with respect to a newly developed product, this may go a long way to achieving profitability and success. The selection of a good trade mark is probably one of the most important acts that one has to perform once the product is developed, as customers will identify the new product by such a trade mark. In many instances, successful marketing and widespread acceptance of a product are largely due to its appealing name or trade mark, accompanied by proper promotion and advertising. Once the trade mark has been adopted, it should be registered in the Trade Marks Office to provide the protection afforded by federal statute. If the product is to be manufactured, sold or licensed in some other countries, similar considerations should be made with regard to each such country."

Jan 1, 1973

Five watersheds, ranging in size from 29 to 49 acres, were selected in East-Central Ohio to investigate the hydrologic and water quality conditions occurring before, during, and after surface mining. Four of the watersheds will undergo surface mining, involving either the Number 6, 9, 11, or 8 coal seams, and one watershed having an outcrop of the Number 6 coal will be operated as a control watershed. To determine the premining hydrologic and water quality conditions (Phase 1), physical information was obtained for each watershed and instrumentation was installed for obtaining hydrologic data and water quality samples. In addition to topographic maps, soils and vegetation maps were prepared. Stratigraphic columns were developed from geologic cores; networks of observation wells and of soil moisture access tubes were installed; and weather stations were established to measure temperature, humidity, wind and solar radiation, and to collect precipi¬tation samples. Field data were collected over a 10-month period for one watershed and for about 8 months on another watershed before surface mining began. The other watersheds continued in the premining data phase. These data were for precipitation, temperature, relative humidity, wind speed, solar radiation, snow and frozen soil, soil moisture, infiltration (rainfall simulator), spring discharge, runoff from watersheds, and ground-water levels. Also, samples of runoff and ground water were obtained for chemical analyses and additional samples of runoff were acquired for suspended sediment load determinations. Over the study period, precipitation was not very representative of the long term averages, but data are available from the control watershed for a representative 7 year period which should prove invaluable in modeling the hydrology of the project watersheds for the premined conditions. Spring discharges (before mining) from the upper aquifer of two of the watersheds averaged only 508 and 652 gallons daily. The proportion of precipitation occurring as surface runoff from the large watersheds ranged from 8 to 36 percent and the peak discharges from 5.86 to 81.95 cfs. Base-flow and runoff water samples from four of the watersheds (unmined conditions) were collected and analyzed quantitatively for 39 water quality parameters. Monthly precipitation samples sediment fractions of the base flow and runoff were analyzed for 22 and 17 parameters, respectively. The average concentrations of the water quality parameters for the watersheds (unmined), except for suspended solids, were as low or lower than the EPA recommended maximum allowable concentrations in drinking water. Several parameters in precipitation equaled or exceeded the levels of corresponding parameters in runoff water. The average concentration of suspended solids in storm runoff ranged from 118 to 1110 mg/l, and for base flow the range was from 44 to 247 mg/l; the higher concentrations were associated with the watersheds exhibiting the greatest disturbance. Iron ranged from an average of less than 3 µg/1 to 228 µg/1. Manganese ranged from less than 41 µg/1 to 334 µg/I. Ground-water systems (unmined condition) are described for the five project watersheds. Each watershed was found to have two major perched aquifers within the top 250 feet. Generally, these perched aquifers involve local flow systems, though flow across watershed boundaries in some areas. Recharge is mostly from local precipitation and discharge is mostly as spring flow, base flow, evapotranspiration, and leakage through the underlying confining bed. Shallow ground water was commonly of the calcium bicarbonate type. Although dissolved-solids concentration was generally 200 to 600 mg/1, brackish or salty ground water was present in several areas. A composite hydrologic model for the project watersheds will consist of separate ground-water, unsaturated flow, overland flow, and evapotranspiration component models. The ground-water model (a modified quasi-three--dimensional U. S. Geological Survey model) operates on a grid network and the newly formulated unsaturated flow model was divided into overlying prismatic elements for numerical solutions. The unsaturated flow model includes provision for incorporating the evapotranspiration model. An available distributed kinemetic overland flow model was utilized. An analyses was made of one of the costs of reclaiming coal mines; the legal and administrative costs of complying with legislation. Such costs borne by coal companies under the Ohio law are thought to be a surrogate of these costs under the new Federal law. Regression analyses were used to relate the legal and administrative costs to acres in the permit and the tonnage of coal produced.

Jan 1, 1978

By E. S. Moore

"The Centre of the silver-producing section of the Gowganda area lies about 55 miles northwest of Cobalt, and the village of Gowganda is 71 miles by road from New Liskeard. The geological similarities of the Gowganda and Cobalt areas led prospectors westward from the rich Cobalt field, first to Elk Lake and then on to Gowganda, where mineralization was found in 1907. A year later many showings were found, and rich hand-picked ore was shipped. Most of the ore has come, however, from two mines, both of which are still operating; the Miller Lake-O'Brien, which was purchased by Siscoe Metals of Ontario Ltd. in 1945, and the Castle-Trethewey. The annual production of these two mines runs over one and one-half million ounces of silver and considerable cobalt. The total production of the camp has reached about 32,000,000 ounces of silver and a large amount of cobalt, the total not recorded.General GeologyThe general geology of Gowganda is in many respects much like that of Cobalt. There are areas of Keewatin basic and acid Javas mixed with tuffs and basic intrusions. These rocks are deformed and partly altered to schists, and have been intruded by some Haileyburian basic and ultra-basic rocks and by Algoman granite. These were followed by a large number of porphyritic Matachewan quartz diabase dykes. After a period of extensive erosion the Huronian sediments were deposited on a pene-planed surface over all the older rocks; these sediments include large quantities of conglomerate (partly tillite), quartzite, and greywacke. The Keweenawan rocks include the Nipissing quartz diabase sill, later quartz diabase dykes, and one long olivine diabase dyke, the latest Precambrian rock. The area has been extensively glaciated.Structural FeaturesThere has been little folding in the area since the Algoman batholiths were intruded, and the Huronian sediments lie nearly flat, with dips of 10, 15, or rarely 25 degrees. The Matachewan dykes show a remarkably uniform, nearly north strike, indicative of east-west tension when they were intruded. On the other hand, the dykes later than the sill strike nearly east, tangentially to the northeasterly and northwesterly strikes of the Miller Lake basin."

Jan 1, 1949

By James D. Bliss

Sedimentary deposits of pluvial Lake Bonneville are an important source of sand and gravel suitable for aggregate and construction in Utah. Data on Lake Bonneville basin sand and gravel deposit thickness, volume, grain size, percent of fines, and durability were statistically analyzed to detect variations associated with geologic domains, geographic location, Lake Bonneville shorelines, and sand and gravel deposit type, and to construct quantitative deposit models. Analysis showed several trends; (1) sand and gravel in younger shorelines was slightly more durable and the deposits considerably larger in volume, (2) younger shore- lines are also more likely to contain more than one genetic deposit type, (3) the volume of terrace deposits is larger than beach deposits, (4) terraces and beaches are generally thicker than spits and bars, (5) the northern part of the Bonneville Basin contains slightly more durable sand and gravel than the southern part of the basin and is more likely to contain deposits composed of more than one genetic deposit type, aid (6) the Wasatch domain deposits are composed of more than one genetic deposit type more often than deposits of the Basin and Range domain. Three additional conclusions with immediate economic significance are; (1) the median sand and gravel deposit in the Wasatch domain, 360,000 m3 (275,000 yd3), is three times larger than that of the Basin and Range domain (120,000 m3 [90,000 yd3]), (2) the median deposit thickness in the Wasatch domain, 5.8 m (19.0 ft), is nearly twice that of the Basin and Range domain (3 m [lo ft]), and (3) the Wasatch domain also contains slightly larger diameter gravel. These three conclusions are significant because the trend for sand and gravel development in the Bonneville Basin is to move from the Wasatch domain to the Basin and Range domain. Smaller, thinner deposits with smaller diameter gravel will require more surface area to mine than would have been necessary in the Wasatch domain. The result is a higher cost for sand and gravel in construction projects in the Salt Lake City area, especially since the gravel must also be hauled farther.

Jan 1, 2001

By Robert G. Bottge

The Bureau of Mines investigated the availability of the land in south-central Alaska for exploration and mineral development of locatable minerals under State or Federal laws. The land ownership for an area of nearly 72.5 million acres in south-central Alaska was divided into 3 availability categories and 15 subcategories. In July 1985, 31.0 million acres of the study area were available for mineral exploration and development, 6.2 million acres were available with restrictions, and 35.3 million acres were unavailable. About 23.6 million acres in the study area are underlain by mineral terranes. About 9.9 million of the 23.6 million acres are available for mineral entry, 2.4 million acres are available with restrictions, and 11.3 million acres are unavailable. While much of the land currently classified as unavailable will be reclassified once it is conveyed to the State or to Native corporations, about 22% of the unavailable lands underlain by mineral terranes are now Federal parks, preserves, wildlife refuges, wild and scenic rivers, and military lands, all of which are considered permanently unavailable for mineral exploration and development.

Jan 1, 1986

By D. R. Parker

"This paper canvasses emerging trends in public policy and law, which may influence the zinc industry's interest in recycling. There are forces at work beyond direct economic benefits that will drive recycling of zinc, including:• corporate determination to pursue sustainable practices and product stewardship.• public perceptions and pressure,• customer and investor demand,• workforce recruitment, and• protection and expansion of marketsIn this paper, these ""indirect"" forces are examined with particular focus on the zinc industry: It is concluded that, in today's world with an emerging precautionary approach to policy and law making, public perception concerning the environmental implications of metal products, and the need to conserve resources for future generation, a strong industry response is required."

Jan 1, 2000

By C. W., Davie

"DEFINITIONDiatomaceous earth consists almost entirely of the silicious remains of minute flowerless aquatic plants known as diatoms. The name diatomaceous earth, therefore, is to be preferred to others such as trade names, inappropriate terms, or names correctly applied to some other product. The following names should, therefore, not be used for diatomaceous earth,-- kieselguhr, infusorial earth, diatomite, celite, moler, bergnehl, English rottenstone, tripoli, tripolite, fossil earth, desmid earth, white peat, tellurine, randanite, ceyssatite, or any trade name.FORMATIONDiatoms live in practically all kinds of water, fresh or salt, hot or cold, still or running and under different conditions of depth and pressure. These minute plants assimilate inorganic salts from their environment and produce skeletons of silica much as mollusks secrete lime and form their Shalls. When the diatoms die they settle to the bottom together with anything else which may be present, such as sand, clay or volcanic ash. The organic matter gradually disappears leaving the silicious skeletons of the diatoms which, with impurities, make up the deposits of diatomaceous earth. These deposits which are still being foamed at the present time and which were produced throughout very different epochs, were more prolifically formed in the Tertiary, so that the thickest beds so far discovered are of that Age."

Nov 1, 1925

By Richard C. Moore

The U.S. Bureau of Mines contracted a study to review the air and water monitoring requirements of five Federal environmental acts (the Federal Water Pollution Control Act, the Safe Drinking Water Act, the Clean Air Act, the Surface Mining Control and Reclamation Act, and the Resource Conservation and Recovery Act) and to compile information on the currently available monitoring instruments. A literature review of the acts and their associated regulations was conducted to determine applicability to the mining industry as well as any air and water monitoring requirements. In addition, an industry search and literature review was performed to assess the instrumentation available to comply with the monitoring regulations. Based on this research, the instruments are classified by general applicability to air, surface water, or ground water monitoring, then catalogued by monitoring parameters. A discussion is provided on recommended and innovative monitoring techniques.

Jan 1, 1981

By Edwin G. Sharp, Frank S. Gaunce, George M. Freeman, Denis J. Kemp, Eric Dulson, Paul Salmon, Ernest R. Hamilton, Carl E. Parden

"THE ECSTALL ZINC PLANT was built for the treatment of the Kidd Creek zinc sulphide concentrates. Construction proceeded throughout 1970-71, with operations beginning in April 1972. The two concentrate types treated differ principally in minor impurity and precious metal contents. Processing flexibility was required to allow efficient recovery of the by-products, especially cadmium, copper and silver. The conversion of the zinc sulphide concentrates to end products follows a sequence of operations that are common to most electrolytic zinc plants and typical of the ""Tainton- Jephson"" flowsheet.1. Roasting in air at an elevated temperature to convert the metal sulphides to soluble metal oxides (calcine) and sulphur dioxide. The sulphur dioxide is converted to sulphuric acid in a contad plant and shipped by train to market.2. Leaching of the calcine in spent electrolyte to effect extraction and recovery of zinc as zinc sulphate solution, leaving an insoluble residue.3. Purification of the clarified zinc sulphate solution by cementation with metallic zinc dust to remove impurities detrimental to the electro-deposition of zinc or detrimental to product purity. The solids from cementation are the starting materials for secondary metal recovery.4. Electrolysis of the purified zinc sulphate solution to reduce the zinc to the metallic state while coincidentally regenerating the sulphuric acid for recycle to the leaching step."

Jan 1, 1974

By L. A. Neumeier

The Bureau of Mines investigated hot-rolling and forging characteristics of experimental ductile iron castings, both sand and permanent-mold, made with charges containing up to 70 pct foundry pig iron and 95 pct steelmaking pig iron. Between 1,550° and 1,950° F, most castings could be rolled to 90-pct reduction or forged to 70-pct reduction without serious cracking. Charge and composition have less bearing on workability than on subsequent properties. Permanent mold castings could be worked as readily as sand castings at 1,750° and 1,950° F. Plasticity improved with temperature. Small billets were also forged cold to 50-pct reduction without cracking. With equivalent nodularity, composition affects properties of wrought materials by altering matrix structure and strength. Properties vary with reduction and improve with increasing working temperature. Rolled material has high strength and anisotropy, and low ductility, particularly in the trans-verse direction. Annealing reduces strength and improves ductility, but anisotropy persists. At 70-pct reduction, impact resistance in the longitudinal direction is about twice that in the transverse. Annealing roughly doubles impact resistance. Deformation enhances damping capacity. The feasibility of die-forging and bar-rolling of ductile iron was evaluated in trial tests conducted under a Bureau contract. Although workability and ductility of ductile iron are inferior to those of steel, more advantage could be taken of ductile iron's plasticity to work rough shapes to final dimensions.

Jan 1, 1980