Search Documents

By J L. Mauk

 Broken Hills is an adularia-sericite epithermal Au-Ag deposit, hosted in flow-banded rhyolites and overlying rhyolitic pyroclastic rocks in the eastern Hauraki Goldfield. The 7.1 Ma deposit was the largest producer of gold in the eastern Hauraki Goldfield, and was one of very few economic deposits hosted in Pliocene rhyolites. This paper presents the results of a recent study in the upper levels of the deposit. Maps and cross-sections constrain structural and lithological relationships, and the lateral and vertical extent of a breccia pipe û the major feature of the upper levels.   Previous studies in the upper levels of Broken Hills have shown that gold and silver values are concentrated around and within a large breccia pipe, mined by a series of æcaveÆ stopes and in veins. Contour diagrams of Au-Ag data from channel samples indicate that the breccia pipe was a major fluid channel-way for mineralising solutions.   The breccia pipe deposits are part of the dynamic geothermal system that formed the Broken Hills ore bodies; they developed as a result of hydrothermal brecciation in areas of structural weakness within a rhyolite pyroclastic unit that overlies a massive rhyolite lava-flow unit. The main breccia pipe begins near the rhyolite/pyroclastic contact, having the shape of an inverted, inclined cone, and consists of silicified breccia, stringers of quartz, and irregular patches of clay-altered country rock. Smaller zones or pockets of hydrothermal eruption breccia are silicified and contain low grade gold in the matrix and in the adjacent silicified wall rocks.   Quartz has been classified according to its physical characteristics as seen in situ and hand specimens indicate that vein definition decreases upwards, perhaps as a result of changing lithological conditions and/or increasing proximity to the paleosurface. Hydrothermal quartz is widespread as veins and as a replacement mineral, or lining fractures and cavities and overgrowing rock fragments. Breccias contain vein quartz, but some quartz veins cross-cut breccias, indicating that vein and breccia formation was relatively synchronous and overlapped in time.   Disseminated gold-silver mineralisation is associated with vein quartz and silicic alteration of the wall rock within the breccia pipe. The auriferous zones are highly irregular and erratic, and sampling results show a wide range of gold-silver ratios, suggesting that highly volatile physiochemical conditions prevailed during mineralisation.

Jan 1, 2005

By J Addai-Mensah, M Adam, W Skinner, J Begelhole, K Quast

Granulation of iron ore fines into robust granules is critical to successful sintering and blast furnace operations in iron and steelmaking. Iron and steelmakers desire iron ore granules with high strength, uniform size distribution and low fuel consumption to enhance efficient sintering operation. Unlike hematite ore, magnetite concentrates do not granulate easily at low binder dosage to yield coarser granules due to the absence of nucleus particles. This motivates the present study to harness the complementary properties of hematite ore to enhance granulation of magnetite concentrates via blending. The current state-of-the-art in hematite and magnetite blend granulation is reviewed, along with granule property limitations. Preliminary experimental work on granulation of hematite and magnetite blends as a precursor to sintering is reported.CITATION:Adam, M, Addai-Mensah, J, Begelhole, J, Quast, K and Skinner, W, 2017. Enhancing magnetite concentrate granulation by blending with hematite ore, in Proceedings Iron Ore 2017, pp 17–24 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

A reliable laboratory method to characterize the response of free gold particles to flash flotation conditions has been developed. The test has been performed on free milling gold ores as well as synthetic ores, using either a gravity concentrate or gold powder as the gold source, to assess the floatability of gold particles. Trends in free gold flotation kinetics, as well as size and milling effects, were identified for gold recovery based on the different feed types, reagent dosages, and residence times. It was shown that the ultimate recoveries and kinetic trends of gold particles from the gravity concentrate could be enhanced with increased dosage of collector, potassium amyl xanthate. Interestingly, in comparison to gravity-recoverable gold, recovery from pure Au powders was better in collectorless flotation, and cumulative recovery decreased with higher levels of collector addition. Improved coarse particle recovery appeared linked to increased collector additions for both the gravity concentrate and the pure gold powders. In general, coarse gold particles demonstrated slower kinetic rates thaen the fine or intermediate components incomparable tests.

Jan 1, 2015

By David Cole

THE appearance of the Wilfley table in 1897 marked an epoch in the art of concentration of ores. The table has merited and received an almost unprecedented measure of public approval, lasting through its whole patent life. It has been very little improved in itself, or improved upon by competitors. The new machines bidding for popular favor have been of the Wilfley family, but without ability to do markedly better work than the parent m:-chine, or to (to more work except by the use of superimposed decks, the latter having obvious disadvantages. FIG. 1.-The- Butchart RIFFLE System. During the past three years there has been developed at Morenci a new type or arrangement of riffles applicable to the Wilfley type of concentrating table which corrects many of the objectionable features or limitations of the older system and obviates most of the difficulties encountered with it, particularly when handling ores having a low ratio of concentration. The new type is known as the Butchart1 riffle system, and its general arrangement is shown in Figs. 1 and 2.

Jan 2, 1915

By Albert Wraith, Thomas Price, Wayne Boyd, Skip (I. E. ) Hills, Cameron Harris

Most Peirce-Smith converters inject air through tuyeres, with nitrogen representing the majority of gas passing through the process. The nitrogen controls the temperature of the vessel by carrying away heat from the reactions, both globally and locally at the tuyere tip. However, nitrogen adds energy to the bath and contributes to splashing and limits the blowing rate. High oxygen smelting has made streams of gas containing high concentrations of sulphur dioxide commonplace, which can be used to substitute SO2 for nitrogen and drastically changes Peirce- Smith converting (and all other smelting/converting processes as well). Less SO2 is required to carry away the same quantity of heat, which allows higher concentrations of oxygen and leads to the possibility of increased production. The paper investigates this substitution, its impact on converter productivity, and on the remainder of the plant. 181

Jan 1, 2009

By J Cornejo, A Pinochet, C Caviedes

The ore extraction rate and the incorporation of new areas are key operational parameters. In massive deposits mined by caving techniques they both control the cave back geometry, which is mostly responsible for the induced stress state around productive levels. Early detection of deviations from admissible geometries will prevent stability problems related to geomechanical hazards, helping to improve safety and working conditions and reduce the potential for lost reserves.This paper describes a mine planning tool currently in use at the El Teniente mine. This tool involves the control of the cave geometry based on rules that have been defined as a result of different studies and experience collected during the operational history of the mine.This mine planning strategy achieves an extractive mining process with lower risk than conventional planning methods, ensuring ore reserves extraction if followed as planned while reducing unexpected changes in mining sequences.CITATION:Cornejo, J, Pinochet, A and Caviedes, C, 2016. Geometric control for strategic mine planning at El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 191–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By J. K. Whyatt, B. G. White

A comprehensive survey of mine seismicity and rock bursting during development of two sublevels at the Lucky Friday Mine, Mullan, ID, USA, was conducted to better define rock failure mechanisms and sources of ground control hazards. Survey data included rock burst damage reports, seismic event locations and magnitudes and, for the most energetic events, first-motion information. Several subsets of this database, including large seismic events, rock bursts, and microseismic activity near the face, were analyzed. Elements of the large-event and rock burst data sets were nearly independent. That is, there was no relationship between the risk posed by a seismic event and its energy, although such a relationship is well established for the mine as a whole. All data sets showed that certain geologic features appear to control the spatial distribution of events and the spatial distribution of rock burst risk. The data also suggest that, within the scope of this study. the greatest risk of injury occurs when a pocket of heightened rock burst risk is first encountered and that this risk is controlled when miners adapt their practices to these conditions. Recognition of the role of particular geologic features in the spatial distribution of rock burst hazards provides an opportunity for anticipating, rather than only reacting to, a changing level of rock burst hazard- However, much work will he required to make good on this promise.

By Charles Merguerian

In medium- to high-grade metamorphic terrains such as found in New York City(NYC), rock mass texture and mineralogy are important factors in predicting TBM penetration destiny. Integration of data from over two decades of traditional field and tunnel mapping suggest that hard-rock TBM penetration in the NYC area depends upon textural, mineralogic, and structural control. The bedrock of NYC consists of many different lithologic units of varying age, composition, texture, and metamorphic grade including many varieties of intrusive rock. In addition, brittle faults of numerous orientations cut the polydeformed crystalline bedrock, producing zones of highly fractured and disturbed ground and high water inflows. Pre-bid compilation of published bedrock data, drill core analysis by geologists to establish lithologic and mineralogic trends, integrated surface geologic mapping along a proposed alignment, and targeted petrographic and geotechnical investigations to characterize the rock mass conditions together constitute an important prelude to successful subsurface bidding and tunneling. A carefully planned program of as-built geological mapping, structural analysis, fracture class mapping, and monitoring of machine performance data provide important information for adjusting to changed conditions. In complex terrains, a clear understanding of the structural geology of any proposed tunnel line is the simplest and most cost-effective method to mitigate losses encountered during TBM tunneling.

Jan 1, 2005

Principal component analysis of the variation of Cu, Ni, Zn, Pb, Mn, and Cr in a control group of 96 samples of surface ironstone from the Yilgarn Block, Western Australia, was used to derive a simple graphical method, based on only Cu, Ni, and Cr, for discriminating between massive nickel gossans and other ironstones.When the graph was tested by plotting 400 control samples, it failed to correctly classify only nine out of 176 gossans and 11 out of 224 other ironstones.

Jan 1, 1974

By Jean Habimana

Complex and distinct geological units spread along the 7-mile long 30-ft inside diameter Upper Rouge Tunnel CSO Control Project in Detroit, Michigan. Its construction is divided in two tunnel construction packages: The South Tunnel, to be driven in finely laminated weak TG Limy Shale, will be excavated by a shielded TBM with precast concrete segmental lining, while the North tunnel, predominantly in a relatively more competent geologic formation Antrim Shale, will be excavated by a main beam TBM with a two-pass lining system. The adits and deaeration chambers will be excavated by sequential excavation method. This paper addresses the process of selecting excavation methods and lining systems for shafts, tunnels, connecting adits, and deaeration chambers.

By J. F. Wilson

An experimental investigation has been made of gas-driven slug displacements in a system of high gas saturation to evaluate the process for use in a California reservoir. Fluid compositions, temperature, pressure and core permeability duplicated reservoir conditions as closely as possible. The temperature was above the critical of the slug materials. The slug composition required for 100 per cent oil recovery in the linear flow systems was found to agree with that determined from equilibrium phase studies. A qualitative theory for the slug displacement of two-phase systems is proposed and found to be in general agreement with the observed flow behavior. The theory predicts that the length of the reservoir fluid-slug transition Zone will increase with increased initial gas saturation and decrease with increased oil swelling accompanying the composition change from reservoir oil to the critical composition. The precipitation of small amounts of an asphaltic phase during the formation of the transition zone had no adverse effects on the flow behavior of otherwise miscible systems. INTRODUCTION Despite the large number of recent publications relating to oil recovery by miscible displacement, little information is available concerning the behavior of crude oil-natural gas systems at conditions likely to be encountered in field application. The laboratory data reported here were obtained during an investigation of the possibility of using a gas-driven LPG slug in a partially depleted California reservoir. Seven gas-driven slug displacements employing slugs of different compositions and sizes were made in 26- to 27-ft long sandstone cores. The equilibrium phase behavior of the systems was also determined. The features of primary interest in this study are the following. 1. Data were obtained on the displacement of reservoir fluids at reservoir conditions. 2. A high gas saturation existed in the long cores at the start of the displacements. 3. The temperature of the studies was above the critical of the slug materials. 4. A comparison between the flow behavior and equilibrium phase behavior, as illustrated by a pseudo-ternary phase diagram, is afforded for a system of considerable complexity. THEORY Phase Behavior The use of the pseudo-ternary phase diagram to illustrate the phase behavior in miscible displacements has been discussed by Clark, Schultz and Shearin. Sie-vert, Dew and Conley and Arnold, Stone and Luffel' have presented both phase equilibrium and flow data for true ternary systems. For the true ternary, the application of the theory is straight-forward; for a reservoir system represented as a ternary, the theory undoubtedly gives a qualitatively correct picture. One purpose of this investigation was to see if the pseudo-ternary phase diagram could be used to predict with reasonable accuracy the conditions necessary for miscible displacements with actual reservoir systems. MiscIBLE Displacement of Two-Phase System A large number of papers "I3 have treated the miscible displacement of a single-phase fluid from both an experimental and a theoretical viewpoint. However, the normal field application of the process will be in a partially depleted reservoir. Often the state of the system will be such that the mobility of the gas phase is greater

By P. Venkatraman

Laboratory and pilot-scale test data have shown that the innovative feed presentation of the CrossFlow separator provides improved metallurgy when compared to traditional hindered-bed or teeter-bed classifiers. This design feature prevents excess water from entering the separation chamber and disrupting the overall fluidization flow rate within the teeter zone. Recent side-by-side industrial-scale evaluations have verified that this technology can improve overall efficiency, reduce the cut point of separation, and increase throughput capacity. This paper describes the important features that make this novel separator ideally suited for size classification and density concentration. Test data from heavy mineral, phosphate, and industrial mineral applications are also discussed.

Jan 1, 2005

By J Guo, K Williams, J Y. Guo, A W. Roberts, M Jones, B Chen

Numerical simulations using the discrete element method (DEM) were carried out to investigate the flow patterns and stress field redistribution at the hopper and feeder interface. The influences of different filling heights, belt speeds and clearances between the hopper bottom and feeder surface on feeder loads were studied. Meanwhile, experiments were conducted by utilising wedged plane-flow hoppers with different configurations and horizontal feeders with various clearances. The simulation results were compared with theoretical values and experimental measurements. In terms of the cases presented in this study, simulation results reveal good agreements with experimental observations regarding the flow pattern. Being similar to the theoretical values, the simulations provide close predictions on vertical feeder loads for steady flow states, but they may show significant overestimations for initial states. Additionally, suggestions are given for relevant simulation parameters based on the comparisons shown in this investigation.CITATION:Guo, J, Roberts, A W, Williams, K, Jones, M, Chen, B and Guo, Y J, 2017. Simulation investigation of flow patterns and feeder loads at hopper/feeder interface, in Proceedings Iron Ore 2017, pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Nicholas R. Dixon

This report summarizes all work performed under Phases I, II and III of U.S. Bureau of Mines Contract H0387006, "Development of a Prototype Retrofit Noise Control Treatment for Jumbo Drills." The noise and vibration levels of four jumbo drills were characterized and a survey of percussive rock drill usage is reported. A Gardner-Denver DH 123 drill was chosen as a demonstration drill, and extensive noise diagnostic studies were performed. Noise control treatments were designed, developed and evaluated in a reverberant drill test facility. The treatments consisted of an integral enclosure/muffler for the drifter, vibration isolation of the drifter from the enclosure and feed, and a drill steel sheath. A 19 dBA reduction in overall sound power level was achieved with no loss in drilling rate. The prototype retrofit treatments were field tested in an aboveground mine and in a production section of an underground zinc mine. Long-term durability and operator acceptance of the enclosure/muffler treatment were excellent. Preliminary evaluation of the drill steel sheath was encouraging, although additional testing is required.

Jan 1, 1982

By I. Mihajlovic

This paper investigates a potential method for arsenic removal from copper concentrates using hypochlorite leaching. The problems concerning pyrometallurgical processing of copper concentrates with high arsenic contents are discussed. A possible solution to the problem by leaching of natural enargite crystals with sodium hypochlorite under alkaline oxidizing conditions, with enargite converted into crystalline CuO and the soluble arsenic forming AsO43-, was experimentally investigated and results are presented. Kinetic parameters were calculated for enargite leaching, using a model-free approach. Advanced isoconversional methods were used to investigate the dependence of activation energy (Ea) on reaction rate (a). Keywords Enargite, copper concentrate, isoconversional method, kinetics, activation energy.

Jan 1, 2011

By Harry Dobroski

Communications with moving tracked vehicles in a rail haulage mine pose a difficult problem. These communications take place from dispatcher to vehicles or from vehicle to vehicle via the trolley line, which is a very poor communications line. As a result, deadspots and high-signal areas can occur anywhere along the line, or signal can decrease simply as a function of distance. An analysis is made of the trolley line as a communications line, and methods of improving its characteristics are discussed. Data from inmine experiments are presented, showing actual improvements in communications. Recent Bureau developments in new hardware are also discussed. These include an adaptive speaker control for existing carrier phones and a new generation of improved carrier phones.

By José Cuadros

"El presente trabajo señala el proceso de evolución del método de minado en la mina Chupa, perteneciente a la unidad minera de Iscaycruz. La evolución del método de minado se determinó por la búsqueda de mejores condiciones de seguridad y eficiencia en la operación. En ese sentido, los resultados logrados con cada una de las alternativas de minado por subniveles, indica que se ha logrado optimizar las diferentes variables mineras y cumplir con el plan estratégico de Empresa Minera Iscaycruz S.A. (EMISA). Para cumplir con el citado plan estratégico, se debe optimizar el método de minado de Chupa, a través de una mayor producción a un menor costo,así como del aprovecho de las labores de desarrollo y preparación ejecutadas según el planeamiento inicial del minado. Por ello, la secuencia del avance del minado y la reestructuración del sistema de relleno de la mina son los aspectos importantes para lograr este objetivo. "

Jul 31, 2003

By R. F. Randolph, R. S. Fowkes, J. J. McClelland, G. H. Schnakenberg

Between 1986 and 1992, there were268 deaths and 54,642 severe injuries to workers in underground U. S. mining operations. Clearly, this level of health and safety risk is not acceptable. While most underground coal mining jobs are dangerous, some are much more dangerous than others. Many jobs in an underground coal mine are clustered around the working face—the place where machinery digs coal from the surrounding rock. The hazards in this area are numerous: When the coal is removed, the ground around it becomes unstable and can cave in on the workers. The mining machines used there are large, heavy, powerful, and move in many different directions in a very confined space, presenting danger to workers. Also, the machines churn up coal dust that causes black lung and other ailments. Figure1 shows a modern radio remote controlled continuous mining machine and its operator. In a typical mine, the jobs with the greatest exposure to hazards involve operation of machinery that cuts tunnel-like passages into the coal (the continuous mining machine) and machines that insert supportive steel bolts into the rock above the work area (roof bolting machines). The workers who endure these hazards are at almost twice the risk of death or disabling injury than co-workers in other safer areas of the mine. Of the statistics quoted above, 106 of the 268 deaths and 21,552 of the 54,642 severe injuries occurred in jobs involving equipment at the working face. The operators of roof bolting and continuous mining machines account for only 21% of the work force but suffered 40% of the deaths and 39% of the lost-time injuries during1986-1992. These death and injury rates are almost twice the rate for workers in other underground mining jobs (see figure 2). The estimated total cost of the 106 fatalities and21,552 lost-time injuries was $327 million from 1986-1992. On average, each fatality cost over $1 million and each lost-time injury costs in excess of $9,000.

Jan 1, 1994

Note this date. This will be the biggest meeting we have ever held. It is arranged so as to permit you to go immediately afterwards to Salt Lake. City to attend the meeting of the American Institute of Mining and Metallurgical Engineers there on August 31, September 1, 2 and 3. Notify the Secretary of any change in your address.

Jan 1, 1925

In the latter half of 1973 a contract was given to Roberts-Holland Joint Venture for the stripping of the southern exhaust airway.The contract was carried out efficiently and relatively cheaply. It was completed 2 months ahead of schedule.The sinking stage and in particular the drilling jumbo proved to be a success and helped produce an above schedule stripping rate.No major problems were encountered with ground conditions or ventilation. A survey of the shaft showed the diameter to be within the set limits of 5·49 m ± 0·15 m.

Jan 1, 1974