Search Documents

By Chulgi Suk, Hoon Park, Hyonsoo Kim, Hakman Kim, Sangho Cho

Dust emission from blast demolition and other construction activities can be a nuisance; it is widely recognized that fine particles less than 10 µm in equivalent diameter (called PM10) may cause health problems. Mist spray systems, such as rain guns, sprinklers, water/surfactant sprays (or foams) etc., are some of the most effective dust suppression methods. A large amount of research has showed that when water droplets are produced in an equal amount to that of dust particles, the airborne dust is suppressed by the agglomeration of dust and mist particles. A method for generating micro-sized mist from water, achieved by the detonation of explosives in the water tube, was suggested and is called the ‘detonationdriven water bag burst system’. There are many experimentally observed limitations of the explosioninduced water break-up process. The water bag explosion tests were simulated using the AUTODYN software, in order to investigate the aerosolization mechanisms of the detonation-driven water and water break-up process into micron-sized droplets. As a result of the numerical analyses, the diffusion direction of water when detonating in the central interior part of water tube was radioactive and significantly stronger than when detonating in the bottom exterior part; this is due to the compressive flow of the volume change inside of the water tube, which resulted from the blasting wave inside of the tube, as well as the reflected pressure on the ground. Blast tests of full-scaled reinforced concrete columns were conducted to verify the effectiveness of the suggested detonation-driven water bag burst system. The water breakdown and dispersion that occurred while blasting the reinforced concrete columns were observed using a high-speed camera, and dust generation was monitored using four density detectors. The suggested detonation-driven water bag burst system showed that the average dust density decreased by up to 7 mg/m3.

Jan 1, 2016

By Akihide Hosokawa

The void growth and coalescence in model materials involving a pre-existing three dimensional void array (i.e. multiple layers of a void array) was studied by X-ray computed tomography (XCT) coupled with in situ tensile deformation. To reduce the recording time, a new technique called fast tomography was employed. The model materials used in this paper were fabricated by the combination of an ultra-short pulsed laser machining system and a diffusion bonding technique, and two different types of arrays were prepared namely, FCC 1 and FCC 2 type array. This methodology allowed the authors to capture the entire process of growth and coalescence events of a void array embedded in the metal matrix. The failures in the both materials involved internal necking and shear localization. One of the highlights of this paper is that the plastic strain at the onset of void coalescence was measured for each model material. These values are in fact the adequate values to be compared with the coalescence strain predicted by existing void coalescence models such as the Brown and Embury model, the Thomason model and the Pardoen and Hutchinson model. The comparison suggested that the Brown and Embury model underestimated the coalescence in neither of the current model materials, while the Thomason model and the Pardoen and Hutchinson model showed a quite good agreement with the result for FCC 1 material. On the other hand the result from FCC 2 material agreed with none of the models probably due to the geometry of the void array that is not compatible with the existing models.

Jan 1, 2010

By M. Lonoff

G. Campbell The paper by M. Lonoff looks at the importance of byproduct prices on copper production. The paper develops several interesting points on this topic, but there are some points in the theoretical discussion that could use further development. A couple of these theoretical topics will be considered here using the paper's framework of assumptions without concern about how realistic the assumptions are for the copper industry. Lonoff's theoretical model is based on a static, homogenous world where all copper/byproduct deposits are identical, and these deposits are the main source of these metals. Due to the importance of the byproducts to the production decision, the term coproducts will be substituted for the term byproducts to reflect more accurately this condition. The conclusion is drawn that a rise in coproduct prices necessitates a decrease in copper prices because copper production is increased as a consequence of increased coproduct production. The observation that real world behavior does not always follow this pattern is dismissed as "speculation." However, it can be easily shown that within this simple framework market forces might create the observed behavior. The key question to be answered is what causes coproduct prices to rise. Three possible cases will be used as illustrations. The first case is the one implicity assumed by Lonoff. Here, the demand for coproducts increases at all prices (an outward parallel shift of the demand curve) with the demand for copper remaining constant. As reported in the paper, the results are higher coproduct prices, an increase in coproduct production, and lower copper prices due to the resulting increase in copper production. The second case is when the supply of coproducts are constrained-leading to higher market prices. Copper production, as required by the simple model, is also reduced which Reply by M. Lonoff Campbell's comments give me an opportunity to clarify a few points in "Copper and Its Byproducts." That paper examined the affect of byproducts on the copper market and considered the relative riskiness of multi-metal deposits from an investment standpoint. That brief note made no attempt to be exhaustive. Nevertheless, Campbell's comments miss the point of the paper and necessitate a response. My "theoretical model" was static and I freely conceded after introducing the assumption of identical deposits that "none of the assumptions hold." These simplifying assumptions allowed me to bound the possible effects of higher byproduct prices on the copper price by assuming identical deposits and computing average price effects. I took great pains to subsequently explain that since deposits are not identical the identity of the marginal deposit might change due to byproduct price changes. In this case, average price affects will overstate the affect of byproducts on copper prices. According to Campbell, I dismiss as speculation any "real world behavior that does not always follow this pattern" (of metals prices moving in opposite directions). In the byproducts paper I noted that gold, copper, and silver price movements often parallel each other on an intra-day or day-to-day basis. Such movements are largely due to market anticipation of or reaction to changes in interest rates that affect carrying costs of metals stocks. Other movements may be due to anticipated changes in available supply or physical requirements. I loosely grouped these effects as speculative. To distinguish this statement from the main thrust of the paper, I contined "In the long run if gold and silver prices remain high the equilibrium copper price will be lower." The paper set out long run equilibrium conditions rather than attempting to explain price movements on a daily basis or on a year-to-year basis.

Jan 11, 1983

Rb-Sr measurements on total-rock samples of granitic rocks from the Mount Isa region have confirmed the existence of two periods of granite-forming activity. The Kalkadoon Granite, together with the Ewen Granite and possibly an older phase of the Sybella Granite, has been shown to belong to the earlier age-group at 1760 m.y.; the Wimberu Granite and a pegmatite associated with the Sybella Granite have been dated at 1540 m.y. The initial Sr ratio suggests that the Wimberu Granite may be new material of deep-seated origin.Further Rb-Sr measurements have confirmed previously-reported K-Ar results upon biotites from these rocks, whilst showing that, in this metamorphic terrain, biotites have lost varying amounts of radiogenic Sr and Ar, and therefore yield ages which are younger than the true age of the second event.

Jan 1, 1966

By J. Matos e Silva

"Abstract Although one can think that it is very low the probability of a seism occurrence during the execution of an excavation in an urban lot protected by a diaphragm wall curtain, reality shows that whenever a seism occurs in an urban area several diaphragm walls will be affected by it. So it is advisable to consider the seismic action when designing a diaphragm wall curtain. The paper refers the main information about the seismic design of diaphragm walls according to the Eurocodes 7 and 8 and to the Portuguese Norms related to them (respectively NP EN 1997-1 2010 and NP EN 1998-5 2010), as the Eurocodes consider the possibility of each European country to adopt their own seismic parameters as the seismic risk is different in each country. Thus the so-called National Document of Application (in our case the Portuguese Norms) prescribes the seismic local parameters.1 - EUROCODES AND PORTUGUESE NORMS PRESCRIPTIONSAccording to Eurocode 8 - Part 5 and to the related Portuguese Norm NP EN 1998-5 2010, seismic actions on soils should be quantified adopting the Mononobe-Okabe method that gives goodapproaches when compared with reality.From paragraph 7.3.2.2 of the referred Norm, the horizontal seismic coefficient kh will be:"

Jan 1, 2014

By Ogden Malin

IN conducting the manufacture of extruded brass rods and brass forgings it has been noticed that there is considerable variation in the physical properties, particularly the machinability of different rods and forgings, even though the composition, working temperatures and method of manufacture remain the same. It is the purpose of this paper to attempt to establish the cause and extent of this variation, and also to determine whether variations in composition within certain defined limits influence hardness and machinability to any marked degree. The writer believes that this variation probably is due to the variation in grain size of the metal, therefore the microstructure of several compositions under various conditions of working were examined in an effort to establish this as a fact.

Jan 1, 1932

This paper presents a virtual prototype for the stress analysis of cable shovel components based on combination of flexible and rigid body approach. The general mechanical system of the cable shovel is modeled as a multi-body system with rigid and flexible bodies. The relevant theories applied for the dynamic model are described in terms of Lagrangian multi-body dynamics and finite element method. A virtual prototype of the cable shovel is built in the Automatic Dynamic Analysis Mechanical System (ADAMS) environment, which allows visualizing the motion of general mechanical system and analyzing the dynamic stress of structural components of the cable shovel. An example is given to perform dynamic stress of durability analysis for the boom and handle. Attention of this study is devoted to the mechanisms of damage of the cable shovel and also the critical high stress areas. Keywords: Cable shovel, Von Mises stress, Virtual prototype simulation, Stress virtualization.

Jan 1, 2009

By Walter I. Paniagua

Drilled shafts and precast concrete piles were installed for the foundation of several structures in a reconfiguration project of a refinery in Minatitlan, Veracruz, in the Gulf of Mexico. The soils are alluvial deposits of flat land from the Coatzacoalcos River, which are embedded with layers of sand, soft clay, and peat. As part of a QC/QA program, load tests, both static and dynamic, axial and lateral, were performed. In this paper results of 32 axial tests are presented, in which typical load-displacement curves were measured at the top of the foundation elements; from the interpretation of these plots, data were recorded for ultimate side shear and in some cases for end bearing capacities, which are compared with the theoretical results of the final stage of the foundation design. The comparison shows that under allowable loads, side shear determines the bearing capacity of piles, even when the tip is embedded in a hard layer. Underestimation of the side shear is evident; therefore design criteria, as well as the methods used for obtaining soil parameters, should be reviewed.

Jan 1, 2007

By Barry Olson

The Peñasquito deposit in Mexico is one of the largest grassroots precious metal discoveries to be developed in recent years. Goldcorp Inc. acquired the gold-silver-lead-zinc property with the acquisition of Glamis in 2006. The company has since committed US$1.5 billion to construct the mine, mill and associated facilities. The first of two 50-kt/d (55,000-stpd) mill and flotation lines is currently being commissioned while engineering and construction continues on the second line. A high-pressure grinding roll (HPGR) will ultimately take total throughput to 130 kt/d (142,000 stpd). The Peñasquito property is located in the northeast corner of Zacatecas state, Mexico. The elevation of the property averages 1,900 m (6,200 ft) above sea level and it is situated in a wide east-west valley. Except for one small outcrop (Peñasquito), the area is covered by up to 30 m (98 ft) of alluvium.

Jan 1, 2009

By Woodcock J. T

During the dissolution of gold in fully aerated cyanide solutions the CN ion is the active agent, and consequently the usual method of evaluating the dissolving power of such solutions is to determine the CN- concentration analytically. The presence in the solutions of copper and/or zinc which themselves form complex cyanides, may result in erroneous conclusions as to the free cyanide ion concentration determined by titration.In this paper the theory of titration of such solutions has been developed, and potentiometric methods have been used to follow the behaviour of complex cyanides of copper and zinc. The results for cuprocyanides show Cu (CN)s to be the most important copper complex, and in addition they explain the reported low rates of solution of gold in copperbearing solutions which when titrated in the usual way, appear to have adequate free cyanide. An explanation of the misleading value of the titration is given, and suggestions for recognition of the condition are offered. Preliminary results for zinc-bearing solutions show that there is no satisfactory end-point for the titration of CN- in excess of that in the complex Zn (CN) 4=, which dissociates to CN and Zn(CN)g-.

Jan 1, 1950

By J. Z. Cui

In this paper a statistical multi-scale method for the mechanics parameter prediction of the rock mass with random distribution of multi-scale cracks/joints is presented. First the micro-structure of the rock mass with random distribution of multi-scale cracks/joints is represented. Then the statistical second-order two-scale method for the mechanics performance predictions of the rock mass structure with random cracks/joints distribution is presented, including the statistical second-order two-scale expression on the vector-valued displacement, strain tensor and stress tensor, and the algorithm procedure of statistical multi-sale computation for the mechanics parameters. Finally some numerical results for mechanical parameters for the rock mass with random distributions of multi-scale joints/cracks by statistical multi-scale method are shown.

May 1, 2009

By Kerry Lahti, Bryan Ulrich

On Feb. 11, 2005, more than 20 mining professionals gathered in Elko, NV for a day-long round-table discussion on heap leaching. Attendees included project managers, operators and environmental professionals. They represented 10 mining organizations. Knight Piésold sponsored the special event. Its seven representatives included three staff members from the company’s Elko Operation, and one each from its Denver, Cajamarca (Peru) and Vancouver offices. The roundtable format was chosen to allow people from the mining industry to share ideas and experiences in an open forum. Rather than presenting prepared talks, spontaneity was encouraged. This resulted in a lively and enjoyable discussion.

Jan 1, 2005

By R. J. Lytle

INTRODUCTION Prior to excavation in soil and rock, it is useful to know the subsurface structure. This is important information both for safety and for equipment scheduling reasons. It is useful to know whether parts of the subsurface might be potentially troublesome or of different character than is generally thought present. By using geophysical probing, it is possible to infer the location and size of these unusual regions. The ground structure is commonly estimated from core samples taken from boreholes. These cores give a detailed knowledge of the structure in the borehole. However, knowledge of the structure exterior to the borehole can only be extrapolated from core data. By using seismic and electromagnetic cross-borehole geophysical probing, remote probing can be used to sense the region exterior to boreholes. A recent advance has significantly improved the state-of-the-art for defining the ground structure between boreholes. This new procedure utilizes large amounts of data and provides a detailed picture of the subsurface. The data processing algorithms used are similar to those in medical imaging of the human body using x-rays, a science called x-ray tomography. This imaging of the ground is called geotomography, which is a shortened acronym for geophysical tomography. Several examples of geotomography applied to imaging ground structure are presented. Our approach has been to probe the ground with electromagnetic and seismic waves. We map the region of interest with signals transmitted between multiple source and receiver pairs lowered in boreholes on opposite sides of the region (Figure 1). The received signals vary according to the transmission properties of the media

Jan 1, 1979

THE object of this paper is to review certain features in connection with the mining of narrow lodes, say up to 20 ft. or so wide. The types of ore-body to which it is intended to refer are those which occur. chiefly as fissure or shear-Iodes-that is, those lodes which are to be found in belts of country which have been subjected to dynamic stresses, resulting in the formation of cracks and fissures, into some of which has been concentrated sufficient metal-bearing material to form ores. Very frequently one of the walls of such a lode is found to be a fault, or plane of differential movement.The first point which comes up for consideration is the shaft and its position. From the information afforded by the prospecting which has been done on a lode relative to the dip, nature of country, &c., the position of the main hauling shaft can be determined. For purposes of general utility the hangingwall is generally chosen, if a vertical shaft, though, on account of freedom from creeps, the foot-wall would be safer. Vertical shafts are preferable to underlie shafts in many ways; but wherethe lode maintains a flat dip the cost of cross-cutting at the various levels becomes very heavy'. This difficulty may to some extent be modified· by sinking a vertical shaft in the hanging-wall...

Jan 1, 1912

By R. Karl Zipf

Highwall mining is an important surface coal mining method, and it may account for approximately 4% of total U.S. coal production. Highwall stability is the major ground control related safety concern. Ground control plans for highwall mining should specify hole width, web pillar width, barrier pillar width and number of holes between barriers. This paper offers simple design charts for these parameters aimed at providing “ball park” checks. Web pillars containing pre-existing auger holes are analyzed and a design chart for estimating their minimum width is also presented. Finally, close proximity multiple seam highwall mining, which may have caused several serious highwall failures, is analyzed. Web and barrier pillar recommendations for this special situation are presented.

Jan 1, 2005

By R. Kaushik

According to the U.S Department of Energy (DOE), mineral processing activities including comminution (size reduction) uses 4% of the world electrical energy consumption. Such numbers reinforce the need to invest in energy savings initiatives in order to produce more using less. ENERGY EFFICIENCY OPPORTUNITIES AND CHALLENGES IN MINING OPERATIONS In addition, DOE, in its Mining Industry Energy Bandwidth Study, has identified huge potential for energy savings for the coal, metals and mineral industries. Even knowing the overall causes of energy waste and some potential tools for remediation, mining companies may struggle to apply such tools and get the desired results due to the following reasons: ? Limited staff ? Lack of accurate economic and investment analysis to justify energy savings projects ? Lack of knowledge to identify low or no-cost savings opportunities ? Internal competition for resources According to the workforce and talent management experts, the Talent Strategy Advisors, the demand for mining engineers is expected to exceed supply by 30% by 2013. Mining personnel are likely to be burdened with increasing and varied workloads with limited training. This will result in the need for automated and simple tools to support energy efficiency activities. Mining engineers will simply not have the time and resources to create such tools, collect and analyze the data to make decisions, and track results.

Feb 27, 2013

By Hookings H. J

UNDER a contract relating to the sale of a Broken Hill concentrate, the differentiation between granular and slime concentrate is determined by the proportion of the material which will pass a 200-mesh (I.M.M. standard) screen, and this has led to considerable attention being devoted to the question of laboratory sizing tests with screens of this order.It was found that many of the screens turned out by the makers during the war, and also since its termination, did not conform with the I.M.M. specifications as closely as some supplied in pre-war days. A perfect screen is hardly to be expected, but when the above contract was framed the parties anticipated that, by special care being taken during manufacture, a screen at least as good as the best pre-war screens would be available. This, however, has not proved to be the case, and the large irregularities in screens recently supplied render them useless for sizing determinations under the contract. The makers were approached through the Institution of Mining and Metallurgy, London, with the view of obtaining a few screens conforming as closely as possible to the 200-mesh I.M.M. standard, and in response to a request twelve pieces of screen were...

Jan 1, 1922

By Ron Lutz

In today’s world, production is the name of the game. We are all in business to make money. In the Quarrying and Mining industry the same holds true. The primary goal is to develop the best drilling and blasting program available to maintain uniform fragmentation to maximize production. Also we want to maintain drilling and blasting costs and minimize escalators. This paper is intended to discuss ways for all parties (quarry’s, blast service and drill companies) to attain this through understanding what can be done to help blasthole drilling and production. Blast designs and seminar’s emphasize the accuracy of drilling to produce better fragmentation. Blast design must also include basic concepts in the drilling process. The type of drill to be used for example whether it is a crawler or truck mount, top hammer or down the hole is important. Quarry operators have a role to play as well. They hold the key to the production of drilling. What the customer does or does not do has a direct effect financially to the drilling. The phrase of pay me now or pay me latter comes to mind. This paper will explore the detail of planning that is required by the quarry and/or blast service companies before a single hole is drilled. The drill must be able to meet the production need of the operation. The type of drill available and what can and cannot be done. The drill cost must be competitive. This paper will touch on comparison drill costs from 1967 to 1999.

Jan 1, 2000

By William A. Beck

This report describes the loading and transportation practices employed at the zinc-lead mines of The Eagle-Picher Co., Jo Daviess County, Ill., and Lafayette County, Wis. The report also gives a brief history of the Illinois-Wisconsin zinc-lead district and the operations of the company in the area. The diesel-powered, rubber-tired loading and haulage equipment is described and illustrated from the operational point of view only, and an analysis is made of the materials-handling system without going into health and safety factors. The costs per ton of the various components of mechanical loading, underground haulage, underground crushing, and hoisting for fiscal year 1960 are tabulated.

Jan 1, 1964

By Tyler Acorn, Brandon Wilson, Jeff Boisvert

Scenario-level uncertainty is a representation of large-scale differences encountered when considering ultimate mining pits optimized over various subsets of stochastic realizations. Accounting for scenario-level uncertainty allows mine plans to be assessed against several probabilistic subsurface interpretations. Scenario-level uncertainty is found through clustering stochastic geostatistical realizations and optimizing final pits across the realizations in each cluster. Where these pits are geometrically different, plans for each scenario differ. Knowing these differences allows the value of each planning alternative to be assessed based on the value and relative probability of each scenario. These results also facilitate the use of formal decision-making frameworks for planning, leading to optimization that better represents the full statistical characterization of the deposit. An example utilizing this approach evaluates both infrastructure placement and drilling program requirements. In both cases, scenario-level uncertainty improves initial plans by limiting opportunity costs and identifying additional potential.