Search Documents

Hatches Creek has been inactive since 1961, but with better metal prices, interest in the field is reviving.The mixed gravity concentrates which were unsalable in 1951 have been experimentally separated into salable wolfram, scheelite, and bismuth-gold concentrates, and a flow sheet incorporating magneticseparation and flotation has been developed.

Jan 1, 1965

By D. Kolymbas

A simple formula is introduced which allows the evaluation of dynamic pile tests. The following case is considered: The pile top is dynamically loaded by an impact. The velocity v of the pile top is recorded over the time. Let v1 and v2 be the first and the second maximum of this curve. Then, the pile bearing capacity (resulting from ideally plastic resistance at the pile wall and at the tip) can be set approximately equal to Z(v1- ½ v2), where Z is the impedance of the pile cross section. Due to the assumption of ideal plastic resistances, radiation damping needs not be taken into account. Material damping may be important in rate sensitive soils (such as clay, even if it is highly overconsolidated). A simple correction procedure for material damping is proposed.

Jan 1, 1989

By E. L. McHugh, J. M. Girard

This paper discusses the results of two recent case studies in which high-tech prototype instruments were used. The first case study describes the results of a ground-based hyperspectral imaging tool used to map the geology of an open-pit mine highwall. The second case study outlines the use of interferometric synthetic aperture radar and how this type of radar can be used in a variety of geotechnical situations. These case studies are part of an on-going research project at the National Institute for Occupational Safety and Health’s (NIOSH) Spokane Research Laboratory. The project objective is to implement engineering controls and design methods in order to reduce the number of injuries and fatalities associated with slope failures at mining operations. Project personnel are hopeful that these new developments in technology will lead to better geotechnical monitoring and design in slope stability and other important areas of rock mechanics.

By W. A. Heitbrink, J. D. Ashley, R. E. Gresh, J. A. Organiscak, A. B. Cecala

Many different types of mobile equipment used in surface coal mining utilize enclosed cabs to protect equipment operators. The overburden removal process is extremely dusty and can cause excessive exposure to respirable dust, especially crystalline silica. After equipment is used for years, many components of the enclosure deteriorate and its effectiveness is greatly reduced. This report discusses a cooperative research study performed on an Ingersoll Rand DM45E surface drill, retrofitted with a new Sigma pressurization and filtration system. Respirable dust concentrations were substantially reduced from 0.64 mg/m3 during pre-testing to 0.05 mg/m3 during post-testing with the new system, representing a 92% reduction in dust levels in the drill cab. This new system appears to be a very well-built and sturdy device, well-suited for the mining industry.

Jan 1, 2002

By R. L. Rough

Photoelastic, wire resistance, and borehole-deformation gages were used to measure the in situ strains when an outcropping Black Hand Sandstone Formation in Hocking State Forest, Hocking County, Ohio, was overcored to stress-relieve the surrounding sandstone. Strains transmitted to the photo-elastic gage did not produce isochromatic patterns suitable for quantitative analysis. Strain readings from the wire resistance gage indicated tensile-strain loading during overcoring; readings from the strain-gage bridges in the borehole-deformation gage indicated compressive-strain relaxation during overcoring. The magnitude and orientation of the computed stress fields obtained from both gages were comparable when the corresponding tensile and compressive elastic moduli were applied. Stresses computed from deformation and resistance gages at depths to 5 feet showed the maximum stresses to range from 1.042 to 2.121 times greater than the minimum stresses. The bearings of principal stresses calculated from the deformation gage readings varied between N 61° E and N 83° E; the wire resistance strain gage bearing computations varied between N 68° E and N 82° E. Measurements of in situ strain in sandstone were shown to have promise but to require further development in field technique that could likely be achieved through experience.

Jan 1, 1971

By Christopher Mark

A coal burst is defined as the sudden, violent ejection of coal or rock into a mine opening. Coal mines in the North Fork Valley (NFV) of Colorado?s Gunnison River have a long history of coal bursts in a wide variety of settings. These have included longwall and room-and-pillar, development and retreat, and single- and multiple-seam mining. In contrast to other coalfields, where bursts are typically associated with strong, massive sandstone and extremely high stress, many bursts in the NFV have occurred beneath shale roof and some distance from the most highly stressed locations. The goal of this paper is to attempt a systematic study of the entire burst history in the NFV, in order to gain insight into their characteristics and causes. The primary sources of information are the reports of investigations conducted by the Mine Safety and Health Administration (MSHA) Roof Control Division over the past 15 years. This paper provides details on the geologic mapping conducted as part of these investigations, as well as a regional plot of burst locations using a Geographic Information System. The mapping indicates that many of the NFV bursts have been associated with structural features, including low-angled faults and well-defined zones of high-density jointing that exhibit little or no displacement. Some of these features appear to extend for several miles, impacting more than one mine.

Jan 1, 2012

"The objective in controlled blasting is to reduce overbreak to control the final pit wall slope, shaft, drift ditch, bench, etc. to the final planned excavation limit. The six main types of controlled blasting utilized today are:1. Line Drilling2. Cushion Blasting3. Smooth Wall Blasting4. Buffer Blasting5. Presplitting or Preshearing6. Air Deck Presplitting"

Jan 1, 1994

By Alicia Esther Ares

The family of Zn-Al (ZA), Zn-Ag and Zn-Al-Ag (ZINAG) alloys offers high mechanical properties, ease of finishing, the advantage of low energy and pollution-free melting. Also, present alternatives to the well developed alloy systems, such as brasses, bronzes, cast irons and aluminum alloys. The main objective of this paper is to measure thermal parameters in ZA, Zn-Ag and ZINAG hypoeutectic and hypereutectic alloys directionally solidified which present columnar, equiaxed and columnar to equiaxed transition structures (CET). Also, estimate the mechanical properties, such as microhardness and tensile parameters and correlate these with the thermal (cooling rate) and structural parameters (grain size and dendritic spacing). The different types of structures were analyzed with optical and scanning electron microscopy. The results showed the influence of concentration, microstructural arrangement and thermal conditions during solidification on the mechanical properties. The results of the present investigation are compared with previous experiments.

Jan 1, 2010

By Christopher Mark

Severe dynamic multiple seam interactions can occur when active mine workings are subsided by underlying mining activity. The most dramatic events are usually caused by longwall mining or pillar recovery beneath open, overlying entries. But pillars in abandoned workings can also fail and cause subsidence and damage an overlying mine. This paper describes a case history in which an apparent ?pillar squeeze? in the abandoned workings of a lower seam was initiated during retreat mining in an upper seam. The event subsequently extended more than 1,500 ft and ultimately closed the upper seam mine. Analysis indicated that the pillars in the lower mine were adequately sized for the lower seam mining and were not affected by the initial development above them. When retreat mining in the upper seam had progressed several hundred feet, however, the pillars located directly beneath the pillar line were overloaded, and an extensive squeeze initiated in the underlying workings. The squeeze, in turn, subsided the overlying workings, causing widespread rib falls and roof instability. Previous examples of dynamic multiple seam interactions resulting from delayed subsidence of underlying workings have been reported in the literature. This is, apparently, the first recorded incident in which pillar recovery in an active mine triggered pillar failure in an underlying mine, which then triggered a dynamic interaction that impacted the active overlying seam.

Jan 1, 2012

By N T. Moxon, L W. Armstrong

Explosive manufacturers have for many years provided a service to the mining industry which has,until recently, been unchallenged by mine operators. Today mine operators are more aware of the properties of explosives required to perform particular tasks within their operations. These properties can be reliably quantified using the test procedures described in this paper for emulsion adn ANFO based explosives. Details of an end-user sampling programme desgined to provide quality checks on explosives supplied to a mine site are also discussed.

Jan 1, 1991

The rapid advance in the adaptation of scientific knowledge to the treatment of ores, resulting in improved chemical and metallurgical processes, has enormously increased the possibility of working lodes profitably, which a few years ago were passed over as unpayable. By the discovery of chlorination, and later of "Cyanidation," by the highly improved methods of concentration, and by the rapid advance in our knowledge of smelting (for which we are greatly indebted to Americanmetallurgists), and by the gradual replacement of scientifing principles and enlightened management, for rule-of-thumb methods formerly in vogue, many large low grade bodies have been opened, and are now paying dividends, which were,twenty years ago, looked upon as hopelessly unpayable. It has been more especially in these large low grade ore bodies, that modern methods have been benefical; for small lodes must be rich to pay at all, as they cannot be worked on the same gigantic scale, but even in these a percentage of metal is saved which formerly was absolutely lost.To make these large deposits remunerative it is, however necessary to try and find the point of greatest economic advantage, to handle the ore in vast quantities, to erect huge plats to treat it, to substitute automatic appliances for hand labour as far as possible, and to combine several processes supplementary to one another, so that ore which is not amenable to one process, shall be saved, by another; and by doing...

Jan 1, 1901

By Peter Zhang

Shield recovery in a longwall move is normally conducted from tailgate to headgate. However, if the face is wide and the immediate roof is weak, difficult conditions with considerable roof sag, excessive shield load, and local roof falls could occur as the shield recovery proceeds to the middle of the face, causing delays in shield recovery. The situation could be aggravated when a pre-driven longwall recovery room is employed. Alternatively, a bi-directional approach for shield recovery, i.e. shield recovery starting from the middle of the face towards both tailgate and headgate, can alleviate the roof sag significantly by quickly withdrawing the shields towards the lower abutment pressure zones at the headgate and tailgate sides. In this case, the bi-directional shield recovery approach was used in a longwall move for a 1450 ft wide face under weak roof conditions. Shields were successfully withdrawn within five days without experiencing significant roof sag. The time-dependent roof-to-floor convergence, shield pressure, and roof conditions were monitored during shield recovery. 3-D finite element modeling was conducted prior to longwall move to evaluate the difference between a uni-directional and a bi-directional shield recovery during a longwall face move. Vertical stress, yield zone in and around the recovery room, load on the shields, and convergence at the center of the shield canopy were obtained from computer modeling, and compared with the data from field monitoring. Finally, the advantages of the bi-directional shield recovery are discussed.

Jan 1, 2007

By Bengt L. Stillborg

INTRODUCTION This paper summarizes the result of a two and a half year research program. The objective of the research was to develop a fundamental understanding of the Rib-in-Roc method. Through the development of a new model technology, namely three-dimensional physical models which powerfully exploit the results of dimensional analysis Stillborg, Stephansson and Swan (1), it has been possible to establish the contribution to both permanent and immediate stabilization of a large underground opening pre-reinforced by the Rib-in-Roc method. Using the results from these physical models and earlier work by Stillborg and Stephansson (2) and Åkesson (3), a conceptual synthesis is given in this paper so demonstrating the Rib-in-Roc method to be a practical working system of pre-reinforcement. DESCRIPTION OF THE RIB-IN-ROC METHOD To give the reader an idea of how this method of pre-reinforcement is performed, a short description will be given, Figure 1. Before any full-scale excavation takes place an entry is made in the host rock and rib raises are driven around the proposed opening. These raises are made at a spacing that is dependent upon rock quality; an opening in poor rock needs more ribs per length of opening. As the ribs are driven they are used as a site from which very competent rock bolting can be done. As a rib is excavated it is filled with reinforced concrete. Finally after having in this way reinforced the zone around the proposed opening, (a reinforced arch is formed) the displacements are automatically controlled as the opening is being excavated. Using this method openings with a span of 50-60 meters (160-200 ft) and a height of 60-80 meters (200-260 ft) are likely to be realised.

Jan 1, 1979

By W. R. Hardwick

This paper describing the mining methods of the Inspiration Consolidated Copper Co. is one of a series being prepared by the Bureau of Mines on mining methods and costs in various mining districts of the United States. The story of mining at Inspiration is of particular interest because, after 127,812,000 tons of low-grade copper ore were successfully mined, the mining method was changed from block caving to open-pit. As the open pit became deeper, many features of the former block-caving operation that were exposed elucidated concepts of the mechanics of caving that previously had been assumed but not observed. The conversion to open-pit mining was accomplished by unique combinations of equipment and the introduction of ingenious engineering and operating practices that have extended the expected life of the mine for many years.

Jan 1, 1963

By F Gervilla, J Laukkanen

The Kevitsa Ni-Cu-PGE deposit in northern Finland contains disseminated Ni-Cu-Fe sulfides, and platinum-group minerals (PGM). The 2.05 Ga-old ultramafic-mafic, funnel-shaped intrusion is intruded into a volcanosedimentary sequence. The major ore minerals are pentlandite, hexagonal pyrrhotite and troilite, chalcopyrite, cubanite and magnetite. Pyrrhotite and pentlandite are replaced by pyrite, millerite and heazelwoodite near the surface. Nickeline, maucherite and gersdorffite are locally abundant. A pilot feed sample of 575 t of the main orebody at Kevitsa had average grades 0.45 per cent Cu, 0.36 per cent Ni, 1.85 per cent S, 0.33 g/t Pt, 0.34 g/t Pd and 0.19 g/t Au, with 0.06 per cent Ni contained in silicates. Higher PGE contents (2 - 27 ppm) occur in a vertical N-S bearing fault zone. The PGM (n = 6022) mapped in specimens of four drill holes, consist of sperrylite 34.7 vol per cent, braggite and cooperite 18.5 vol per cent, geversite 17.2 vol per cent, moncheite 14.7 vol per cent, merenskyite 6.7 vol per cent, stibiopalladinite 4.3 vol per cent, sobolevskite 1.9 vol per cent, kotulskite 0.7 vol per cent, michenerite 0.6 vol per cent, keithconnite 0.3 vol per cent, rustenburgite 0.1 vol per cent, melonite, froodite, laurite together 0.1 vol per cent and only a few grains of sudburyite, irarsite, vysotskite, erlichmanite, hongishiite, Pt-Cu-alloys, three undefined Pd and Pt bismuthinides and antimonides and a Pd-Cu-bearing Pt-Ni-Fe sulfide. Most of the PGM, 62 per cent, are enclosed in silicates, 29 per cent are intergrown with sulfides, nine per cent are within sulfides. A portion of the PGE occurs in solid solution in sulfides and arsenides. Ni flotation yielded smelter-grade concentrates averaging 12.2 per cent nickel. The average sulfide Ni recovery is 78.8 per cent and total Ni recovery is 65.3 per cent. The average Pt is 10 g/t at 55 per cent recovery, Pd 7.7 g/t at 38 per cent recovery and Au 1.6 g/t at ten per cent recovery. Cu concentrates averaged 28.6 per cent Cu with an average recovery of 78 per cent and further 11 per cent in the nickel concentrate. The copper concentrate contains 4 g/t Au at 24 per cent recovery. The average Fe to MgO ratio 17.9 is well above the targeted minimum of 4.5. The pilot results show that the previously used TETA (triethylene tetramine) can be avoided and good quality, smelter-grade concentrates can be produced from the Kevitsa ore at economical levels of recovery by conventional flotation methods.

Jan 1, 2008

By A. Pratt

Portland cement is primarily used to solidify backfill in underground mine workings and it represents a major cost in mining operations. CANMET-MMSL has invented an alternative binder technology that does not contain any amount of Portland cement and is made using waste materials, such as development rock and smelter slag. The technology has been successfully tested with many types of base metal and ferrous slag. Research conducted in collaboration with several mining operations in Canada has shown that the CANMET-MMSL binder has considerable potential as a replacement for Portland cement in mine backfill. An integral part of the overall mining operation, backfill is used for two main purposes: safety and environmental remediation. Depending on the mining method used, backfill provides a working surface, stabilizes stope and pillar walls, as well as the surrounding rock mass, and controls caving of stope backs. There are several benefits associated with the replacement of Portland cement in backfill, including reductions in (i) the footprint by placement of slag waste underground, (ii) the environmental effects and long term liability resulting from disposal and containment of slag waste on surface such as acid rock drainage, (iii) GHG as a result of reduced Portland cement usage (the production of 1 ton of Portland cement produces 1 ton of GHG), and (iv) the significant costs associated with reduced Portland cement usage.

May 1, 2010

By Walter C. Lorenz

In connection with its renewed study seeking solutions to problems created by release of acid water from bituminous coal mines, the Bureau of Mines recently surveyed reports already written on the subject. This publication is based on that search. The Problem Poor distribution of water is evident on an ordinary geographic map of the United States. The more abundant supplies of surface water appear to be centered in the northeast, the southeast, and the central humid areas of the country. It is in the midst of this abundant surface water, in the Ohio River Valley, that most of the bituminous coal is mined. Varied industry has located in the valley to use the coal and the river. The coal is a source of power and o raw material. The river provides transportation for raw and finished materials; equally important, it provides the water that is used for cooling and processing in manufacturing. It also serves as a vehicle for the disposal of waste.

Jan 1, 1962

By Patrick J. Coleman, John C. Kerkering

Problem: Mining in the United States remains one of the most hazardous industries, despite significant reductions in fatal injury rates over the last century. Coal mine fatality rates, for example, have dropped almost a thousand fold since their peak in 1908. While incidence rates are very important indicators, lost worktime measures offer an alternative metric for evaluating job safety and health performance. The first objective of this study examined the distributions and summary statistics of all injuries reported to the Mine Safety and Health Administration from 1983 through 2004. Over the period studied (1983 2004), there were 31,515,368 lost workdays associated with mining injuries, for an equivalent of 5,700 person years lost annually. The second objective addressed the problem of comparing safety program performance in mines for situations where denominator data were lacking. By examining the consequences of injuries, comparisons can be made between disparate operations without the need for denominators. Total risk in the form of lost workday sums can help to distinguish between lower and higher risk operations or time periods. Method: Our method was to use a beta distribution to model the losses and to compare underground coal mining to underground metal/nonmetal mining from 2000 to 2004. Results: Our results showed the probability of an injury having 10 or more lost workdays was 0.52 for coal mine cases versus 0.35 for metal/nonmetal mine cases. In addition, a comparison of injuries involving continuous mining machines over 2001 2002 versus 2003 2004 showed that the ratio of average losses in the later period to those in the earlier period was approximately 1.08, suggesting increasing risks for such operations. Discussion: This denominator free safety measure will help the mining industry more effectively identify higher risk operations and more realistically evaluate their safety improvement programs. Impact on Industry: Attention to a variety of metrics concerning the performance of a job safety and health program will enhance industry's ability to manage these programs and reduce risk.

By Mark R. Svinkin

Construction vibrations may be harmful to adjacent and remote structures, sensitive instruments and people. Construction vibration sources have a wide range of energy, displacement, velocity and acceleration transmitted on the ground. Effects of different dynamic sources and soil conditions on construction vibrations is analyzed. Consequences of construction vibrations are developed in various ways. It is important to assess intolerable vibrations before the beginning of construction activities. Guidelines for preconstruction survey are presented. Pre-construction survey and prediction of anticipated vibrations by IRFP method, monitoring and control of measured vibrations are important steps in preventing intolerable vibration effect.

Jan 1, 2000

By Randall Wheeler, R. Frank Chiappetta

2000 HIGH-TECH SEMINAR Blasting Technology, Instrumentation. and Explosives Applications - Orlando, Florida, USA July 24 - 27,200O 2000 BAI - PROTECTION AGAINST LITIGATION WITH GOOD PRE-BLAST SURVEYS, DAMAGE INSPECTIONS AND RECORD KEEPING 1 of 65 Good Record Keeping is Essential for: 1 ) Compliance with any prevailing Local, State or Federal Regulations, ordinances and permits. 2 ) Protection against potential litigation. 3 ) Balancing explosive consumption, use & costs. 4 ) Use in blast designs.5 ) Blast diagnostics & troubleshooting good/bad shots.

Jan 1, 2000