Search Documents

By Mary Ellen Large

This publication of Deep Foundations Institute (DFI) is intended to provide project owners, design engineers and construction professionals with guidelines for selecting cutoff wall and barrier systems and a general introduction to their methods of construction. Three categories of cutoff wall and barrier construction technology (excavated cutoff systems, in situ techniques, and driven cutoff systems) are presented and parameters for evaluating their design and construction are discussed. The information presented was compiled from the opinions of practicing engineers and construction specialists from the DFI Slurry Wall Committee.

Jan 1, 2021

By F. J. Sotillo

The objective of this investigation was to determine the feasibility of using a high-pressure roll mill (HPRM) to improve the separation efficiency of dolomite from apatite in downstream operations when treating high-dolomitic pebbles. High-dolomite samples from four phosphate mines were used for the test program. The research work plan included sample characterization studies; INSTRON tests to develop preliminary crushing data; high-pressure roll mill evaluations to determine crushing parameters, such as feed rates, rolls speed and gap, and applied torque, pressure and energy; and screen, microscopy, and flotation studies to assess dolomitelapatite separation efficiency. The results of the HPRM tests show that commercial products for all four mines can be obtained. Recoveries of 74-82% of the P2O5 and rejections of 46-83% of the MgO were reported with an specific energy consumption of 0.2-0.5 of that of a laboratory rod mill.

Jan 1, 1998

By Elger. G. W.

The Bureau of Mines investigated preheating of continuously fed, fragmented ferrous scrap charges by furnace offgases and utilizing substitutes for imported fluorspar to condition electric steelmaking slags. Three types of continuous scrap charging procedures were investigated to determine electrical energy consumption in a I-st (short ton) electric arc furnace. Cold and preheated scrap charges were continuously fed at rates averaging 37.5 and 43.7lb/min, respectively. The feed rate varied appreciably from test to test owing to hangup of the scrap in the charge bin. Approximately 7 pct less electrical energy was consumed in melting scrap preheated to 8400 to 1,1100 F by furnace off-gases than in melting cold scrap. Overall energy consumptions were 888 kW'h/st for cold scrap, 829 kW'h/st for preheated scrap" and 637 kW'h/st for conventional backcharged scrap. Stack gases from scrap preheating averaged 1200 F and a flow rate of 1,615 scfm compared with 2200 F and 1,302 sefm for cold-charged scrap. Slag conditioners tested included synthetic fluorspar, boric acid, hydroboracite, used aluminum potlining wastes and aluminum anode tailing wastes, and Sorelflux B. The boron-containing conditioners fluidized the slags the best, followed in order by the conditioners containing fluorine and titanium.

Jan 1, 1987

By Donald H. McLaughlin

ZEST in the search for new supplies of metallic ores and petroleum is difficult to maintain with stocks of raw materials accumulating and with over- production rightly or wrongly blamed for most of our industrial troubles. Enthusiasm over new methods of prospecting has consequently diminished and exploration programs in many fields have been drastically cur- tailed. Very naturally the effects have been felt with particular keeness in highly specialized phases of the work, such as geophysical prospecting, for the feverish scramble for new areas in which to drill beneath magnetic or electrical anomalies has abated, and there is even a lull in the firing in the battle over salt domes on the Gulf Coast. It is unquestionably an unhappy time for many of the organizations dependent on this work, but in certain respects the situation may be beneficial in correcting unsound practices that .have grown up through the necessity for haste and for quick decisions. With the restriction of the field to the more competent workers by the harsh rule of survival of the fittest, a general improvement, not only in technique but in business methods, can be expected which may go far in restoring public confidence. Geophysical prospecting in the short period that it has been utilized in North America, has suffered severely both from over-popularity and from excessive abuse. The former evil now

Jan 1, 1931

By A. Himsley, E. Byleveld

"With reference to the chemical constraints underlying the ion exchange process for uranium recovery, a generalized view is presented on the actual and the achievable efficiency of the process. The area considered is restricted to acid leach circuits in combination with nitrate, chloride or sulphuric acid elution.A comparison between actual plant results and the chemical requirements shows that:(a) Unless new and better ion exchange resins are developed, no dramatic change in equipment size and resin inventory is""anticipated. (b) Elution efficiency, especially for sulphuric acid, may be improved considerably. More concentrated eluates may beproduced at lower chemical consumption. A possibility of achieving additional purification solely by ion exchange is discussed.IntroductionThis paper presents a generalized view of the actual and the achievable efficiency of the ion exchange processes for urannium recovery. The study is restricted to acid leach circuits in combination with nitrate, chloride or sulphuric acid elution. The ultimate efficiency attainable with ion exchange is dietacted by the chemical reactions underlying the process. The most sophisticated technology cannot change the diffusion rates in the ion exchange resin nor make the uranium loading exceed its equilibrium valueThe design of an ion exchange plant for uranium recovery involves a considerable number of parameters as a result of the wide variety of pregnant solutions produced from different orebodies. Therefore, a generalized approach of the ion exchange process inevitably neglects some parameters which maylead to significant variations in apparently identical situations.The uranium concentration in the pregnant solution, together with its pH, are the principal variables which determine resin loading and residence rime in the ion exchange system. On the elution side, the type of eluant and its concentration will determine the contact time required and the amount of eluant needed to strip the resin. The temperature, the properties of the ion exchange resin, the total dissolved solids in the feed solution and the competing ions are other variables that affect the chemical performance; these, however, may be considered as a correction of the principal parameters if one is interested only in general trends."

Jan 1, 1980

of our good friends and fellow members: W. S. Worthington H. W. Bullock who left the world better for their having lived in it.

Jan 1, 1932

By Xuehui Li, Xinshuai Shi, Jun Wang, Jianguo Ning, Shang Yang, Zhaohui Zhang

Pressure relief is an important step in preventing and controlling rock burst disasters. Hydraulic slotting has emerged as a strategy for pressure relief and energy release in roadway surrounding rock. There is no qualitative description for the response relationship between hydraulic slotting parameters and the degree of pressure and energy release in a roadway, which is a scientific problem. In this paper, theoretical analysis, numerical simulation, and on-site industrial practice were comprehensively used. First, a structural model for the pressure relief and energy release of coal by hydraulic slotting in a deep roadway was established, and the pressure relief and energy release principle by hydraulic slotting was revealed. The principles and methods for determining hydraulic slotting parameters in the roadway were proposed. Three evaluation indices for the pressure relief and energy release effect of coal after hydraulic slotting were proposed, namely, the stress ratio of coal, elastic energy density ratio of coal, and displacement rate of the roadway rib. According to the evaluation indices, the degree of pressure relief and energy release was divided into three levels: reverse pressurization, full pressure relief, and transitional pressure relief. Then, a FLAC3D numerical model was constructed, the levels of pressure relief and energy release under different hydraulic slotting parameters were analyzed, and the optimal slotting parameters were determined. Finally, on-site industrial practices were carried out in Panel 7312 of the Xinhe Coal Mine. An effect test showed that the effect of pressure relief and energy release was remarkable after hydraulic slotting was adopted on the roadway surrounding rock, which can effectively reduce the risk of rock bursts. These research results can further improve hydraulic slotting technology systems and provide a theoretical basis and technical reference for the stability control of deep roadway surrounding rock.

Sep 20, 2023

By E. V. Cilento, R. C. Laotz, K. A. DiGregorio

"PULMONARY ALVEOLAR macrophages (PAM) protect the lungs by providing a first line of defense against inhaled foreign debris and bacteria. In this role PAM phagocytize foreign matter, secrete enzymes that augment microbial killing and digestion, and produce reactive oxygen me-tabolites (2, 3, 18, 19, 22, 26). However, in addition to this antibacterial function, PAM participate in a diversity of functions, such as tissue repair, lipoprotein metabolism, and immunoregulatory activities (11, 22).Studies have suggested the existence of a heterogeneous population of PAM with respect to immunologic function, enzyme release, phagocytosis, morphological characteristics, expression of membrane receptors, ad-herence, and superoxide (O2•) release (4-7, 10, 16, 21, 23, 28). This heterogeneity has been observed by analyz¬ing subfractions of PAM separated by cell density frac-tionation. For example, using guinea pig PAM, Dauber et al. (7) showed heterogeneity in cell density and size, morphological characteristics, and cytochemical properties, whereas Holian and co-workers (16) reported variations in migration, chemotaxis, O2• release, and pinocytosis among subfractions collected. Similarly, O'Neill et al. (21) observed functional heterogeneity in rat PAM with regard to phagocytosis, O2 • release, and lysosomal enzyme activity.Several investigations have reported a correlation between PAM activity and cell volume. Most studies have shown that O2 release from PAM increased with decreasing cell size (15, 21, 25), although Bielefeldt Ohmann and Babiuk (4) reported a decreasing trend. However, Gallin (13) has suggested that significant variability may even exist within density-defined or cell-volume subfractions that could lead to misinterpretation of results concerning PAM heterogeneity.A better understanding of the heterogeneity in O2 production may be obtained by using single cell meas-urements to evaluate whether functionally distinct sub-populations actually do exist. As such, the present study was designed to examine heterogeneity in O2 • release from single PAM using a recently developed electrooptical technique (8). The initial oxygen metabolite, O2•, produced by NADPH oxidase at the surface of the plasma membrane, was measured by quantifying the reduction of nitro blue tetrazolium (NBT I to a diformazan precipitate. Measurements were made from video recordings of individual cells stimulated by their adherence to the bottom of a culture dish. The cell volume and degree of spreading also were determined directly from the same video recordings, and the data were correlated with the initial rate and maximum amount of diformazan produced by the same cell."

Mar 1, 1992

By J. Richard Kyle

The Pb-Zn ore bodies in the Pine Point district are localized in paleo-solution structures that developed as the result of post-middle Givetian subaerial exposure of the carbonate barrier complex. Sulfides are concentrated in transgressive pale-solution structures that acted as natural bypasses between aquifers and loci for mixing of fluids of different character, one of which contained metals and the other reduced sulfur. Complex ore textures indicate rapid early sulfide precipitation followed by slower sulfide growth. Evidence for both sulfide-carbonate equilibrium and disequilibrium conditions suggest fluctuations in ore fluid composition. District and ore body metal distribution patterns may reflect the nature and movement of mineralizing fluids.

Jan 1, 1979

By Robert W. McKibbin

The Bureau of Mines conducted laboratory tests to determine the slurry transport and deposition properties of coal waste. A 188.5-ft pipe test loop was constructed with instruments to measure density, flow, and power and discharge, suction, and differential pressures. A 20-ton ample of Western coal waste was crushed and screened to 100 pct minus 1/2 in. Eight loop tests using this graded waste were run at slurry densities ranging from 1.15 (25 wt-pct solids) to 1.46 (60 wt-pct sol-ids) 0 The resultant friction-'pressure gradients ranged from 0,06 to 0.24 ft of water per foot of 4-in standard steel pipe. Particle-size degradation was significant.. In a typical loop test lasting 25 min, the minus 200-mesh fraction increased from 19 pct to 34 pct. Deposition tests showed that without the use of a flocculant, the slurries would not dewater when left to stand for 1 week. With flocculant, additional water was releas2d; however, the settled slurries remained thixotropic. Further testing is necessary to determine their suitability for use as backfill material in active mines.

Jan 1, 1983

By G. S. Austin

New Mexico produced 83% of domestic potash and 27% of domestic consumption in 1992. The potash industry of New Mexico produces sylvite (KCI), langbeinite (K2SO4-2Mg(SO4)2), and artificial K2SO4. Average sylvite grade in New Mexico today is about 14%. The average grade of langbeinite is 8-10% Kp. Commercial potash occurs in the middle or McNutt Member of the Salado Formation (Upper Permian Ochoan Series). The 120-m-thick McNutt Member dips about 1° east and contains 11 of 12 potential ore zones in the Salado. The mineralogy and proportion of clay minerals, up to 7% of the ore, influence optimum milling procedures and ore grade cutoff.

Jan 1, 1994

By John F. Papp

Based on a review of historical domestic and international chromium metal production capacity, production, consumption, trade, and trade literature, world annual chromium metal production capacity in 1995 was estimated to have been 38,300 metric tons, a drop from 43,500 tons in 1994. World chromium metal production and consumption were estimated, on average from 1984 through 1992, to have been 21,000 tons per year. U.S. consumption was estimated, on average over the same time period, to have been 6,200 tons per year. The major world chromium metal producers between 1984 and 1995 were China, France, Germany, Japan, Russia, United Kingdom, and United States. From 1984 through 1992, world trade averaged 8,400 tons per year. Germany and the United States accounted for over 75 percent of imports on average during the same time period. U.S. chromium metal import value rose from under $1 per kg before 1964 to over $6 per kg in 1993. Over the same time period, prices rose from about $4 per kg to about $10 per kg. Chemical specifications have become more stringent. Detailed chromium metal trade, prices, value, chromium metal chemical specification, and production capacity by country are reported. A shift in trade patterns was anticipated as Japan exits production and displaces Germany as the second largest importer and as Russia increases its role in world trade.

Jan 1, 1995

By H. E. Elliott, R. S. Busk, A. T. Peters

One of the problems of the fabricator of metals and alloys is the propensity of some composition rarnges toward abnoermal grain growth during certain stages of fabrication. In this respect magnesium alloys are no exception among alloys. Fortunately, convenient foundry control methods have been developed by which the abnormal grain growth possible in certain magnesium-alloy castings can be suppressed. An unusual characteristic of magnesium alloys, however, is that castings of some composition ranges are subject to local grain growth during heat-treatment without the necessity of intentional mechanical stressing of the part prior to heat-treatment. This effect occurs only under certain critical casting conditions, and only in certain alloys of greater than about 8.5 per cent aluminum content, such as C alloy (Mg, 9 per cent A1, 2 Per cent Zn, 0.2 Per cent Mn) and G alloy (Mg, 10 per cent Al, 0.2 per cent Mn). The first observation of this phenomenon in cast magnesium alloys occasioned much surprise, since it is not observed in other meta1s- Jeffries and Archer1 have stated that "the grain size of cast metals, provided they have not been plastically deformed, cannot be changed by heating below the melting point." The study of the conditions leading to abnormal grain growth in cast magnesium alloys, and of the mechanism of this phenomenon, has led to some very interesting observations. Perhaps the most significant of these was the observation that stresses originating from cooling contraction in magnesium-alloy castings are the only stresses necessary, under certain conditions, to cause local recrystallization and subsequent grain growth in the casting during heat-treatment. Before recent developments, this phenomenon of abnormal local grain growth Was a definite problem in the production foundry on C alloy sand castings. Illustrated (Fig. I) is a picture of a casting scrapped because of this defect. A mottled effect is produced in coarse-grained areas by suitable etching solutions. The properties of metal in the affected area are much impaired by such grain coarsening. Ultimate tensile strengths of half the normal value have been measured in metal of this nature. In this paper are described the techniques that have been developed by The DOW Chemical Co. for studying, and in large measure solving, this production problem. Also discussed are studies of the mechanism by which excessive grain coarsening occurs, and the fundamental conditions that produce this effect. The abnormal grain growth discussed in this paper will be referred to as "germinasium since this term has been definedl as any process leading to an abnormally coarse grain size. This paper deals only with abnormal local grain growth that may occur during the solution heat-treatment of certain magnesium-alloy castings, as dis-

Jan 1, 1945

By Y. M. Shneerson, V. M/ Shpaer, E. E. Zhmarin, A. Y. Lapin, E. M. Vigdorchik

This paper describes studies of zinc concentrate oxidizing pressure leaching using the method of mathematical modeling. The concept of a kinetic function was taken as a basis for mathematical modeling of the leaching process. The kinetic function describes dependence of the unreacted component share OJ on the relative time x (the relative time is the ratio of the test duration and the time of complete dissolution). This kinetic function is determined in accordance with the results of batch laboratory tests. The laboratory tests have been carried out on zinc concentrate produced from Kazakhstan zinc-copper ores. Zinc concentrate consisted mainly of three types of minerals: sphalerite (70%), pyrite (13%) and chalcopyrite (10%). Oxidation reactions of sphalerite, pyrite and chalcopyrite have been considered as principal ones. The kinetic characteristics of the process (kinetic function, reaction order, activation energy, duration of complete dissolution of the concentrate components) have been calculated in the course of laboratory tests. The mathematical model was used for estimation of the main technological leaching process parameters (such as process rate, degree of metals extraction, autoclave capacity, heat balance, etc.). Mathematical modeling based on the kinetic function concept allows safe designing of metallurgical equipment and scaling the technology to industrial capacity.

Jan 1, 2004

By Marvin W. Wilson

The Federal Bureau of Mines has conducted laboratory experiments simulating underground gasification of coal to study the feasibility and mechanism of the process and determine the chemical and physical characteristics of a coal-bed during gasification. Laboratory and small-scale field experiments also were made to investigate the properties of coal and other factors affecting the electrolinking-carbonization method of preparing a path through a coalbed before gasification. Laboratory experiments simulating underground gasification of coal: Experiments with a laboratory retort indicated that bituminous-coal deposits could be gasified in place to produce a combustible gas.

Jan 1, 1960

By William W. Adams

Not since complete records of accidents first became available has the safety record of the quarrying and related industries of the United States been as favorable as it was in 1940. The combined accident-frequency rate was lower and therefore better than in any year since 1916, the first year for which complete and comparable figures are available. Although operating companies began to furnish accident reports to the Bureau of Mines in 1911, the reports for that year and the next few years were obviously incomplete as to number of accidents reported, especially slight injuries involving only 1 or 2 days of disability of the injured employees. By 1916 the reports from operating companies appeared to be reliable as to completeness of coverage of slight injuries. Although the number of men employed in 1940 was by no means a record, it represented a gain over each of the 2 preceding years. Likewise, the number of man-hours worked during 1940 was larger than in 1938 and 1939.

Jan 1, 1942

By D. C. Foote

MR. FOOTE: This paper deals with blasting and mechanical loading. The Union Pacific Coal Company does all of its blasting with permissible powder and electric shooting, but this paper deals principally with blasting in connection with mechanical loading. With the introduction of mechanical loading into the coal fields of southern Wyoming one of the main problems to be taken into consideration was the drilling and blasting of the coal. The methods used in blasting coal for hand loading were found to be ill adapted to the mechanical practice, so numerous tests were conducted from time to time to determine a system or systems whereby the coal might be blasted in a form to be easily handled by the loading units. The general practice in blasting coal for hand loading, for example in a room 24 feet wide and seven feet high with an undercut of seven feet, would be to shoot one or two strong breaking shots in the center and one on each rib. While much of the cut would be blasted down in good lump, some coal would be left hanging at the back and ribs. With hand loading, the miners would have time to pull this coal down with a pick between cars and eventually would clean up the place ready for the cutting machine. The loading machine, however, cannot get this coal down and its operation would be delayed while the men were doing the necessary pick work.

Jan 1, 1929

By William H. Schiffbauer

The U.S. Bureau of Mines has been investigating methods and technology that may improve safety and production when applied to existing mining machines. Toward those goals, the Bureau has developed navigation systems that provide machine positional information while in the production area. This research has been limited in the past because the Bureau had only one type of mining machine to do experiments. Addressing this problem, the Bureau, along with Carnegie Mellon University, has developed a generic vehicle emulator, in the form of a wheeled vehicle with an onboard computer, known as the Locomotion Emulator, that provides a software-selectable vehicle emulation package. Preliminary testing by the Bureau has shown that the emulator can accurately imitate the maneuvers of the software selected vehicle type. Now the Bureau can test their navigation systems on different vehicle types without having to procure each of the vehicles. This report completely describes the emulator as well as all the modes in which it can be operated.

Jan 1, 1991

By W. Roggenthen, Z. J. Hladysz, G. D. Callahan, W. G. Pariseau, W. Weinig, C. Randolph-Loar, R. Popielak

A Deep Underground Science and Engineering Laboratory (DUSEL) is being planned at the site of the former Homestake Gold Mine in Lead, SD, under the sponsorship of the U.S. National Science Foundation (NSF) in cooperation with the Department of Energy (DOE). This national facility will host a variety of multidisciplinary science and engineering experiments, including physics experiments that require shielding from cosmogenic radiation. Current plans include construction of large rooms (up to 55 m in width) at depths of 1.48 km (4,850 ft) and 2.25 km (7,400 ft) below the surface. Preparation of the preliminary design required the development of a geotechnical characterization program, including preliminary drilling and coring, core logging, drill hole mapping with a televiewer, drift mapping of the geology and rock structure, in situ stress measurements, and laboratory testing of the mechanical properties of the rocks and discontinuities. Overall rock quality is very good to excellent. Site investigations included geotechnical assessments for the construction of caverns and laboratory modules. The results are favorable and reaffirm selection of the Homestake site for establishment of a Deep Underground Engineering and Science Laboratory.

Jan 1, 2011

By Stephen P. Holt

In the fall of 1946 and spring of 1947 the Bureau of Mines put down five inclined diamond-drill holes totaling about 3,100 feet of bore to test for the possible eastward extension of the Royal Princess ore deposit in Jo Daviess County, Ill. Attention of the .Bureau was first directed to this property by the Illinois State Geological Survey. The history of production of the Royal. Princess mine and reports as to the size and nature of the deposit were considered justification for investigating the trend of the mineralization. This report describes the work done by the Bureau of Mines and presents the data obtained.

Jan 1, 1948