Search Documents

By Albert Ruiz

The 2,250-MW, coal-fired Navajo Generating Station located in Page, AZ draws water from Lake Powell using submersible pumps installed in five inclined shafts. Drought threatens to lower the reservoir to below the existing intakes. A system of new steel-lined intake shafts located on the same site was required for uninterrupted plant operation. The small size of the site, and the need to keep the existing system in operation, required detailed designs and placed significant limitations on construction equipment and activities. The Navajo Sandstone that forms the near vertical shoreline of the reservoir is 98 percent very fine grained quartz, highly abrasive and contains highly fractured intervals that presented numerous challenges to drilling the new 152-m (500-ft) deep, 109-cm (43-in.) diameter intake shafts inclined 23° to 26° from vertical. Spatial constraints, submersible pump design and operational criteria required that each shaft have a unique inclination and orientation and hit a small breakout target located 76 m (250 ft) under water. Sophisticated drilling equipment and techniques as well as state of the practice downhole survey technology and methods were used to make adjustments and maintain drilling accuracy with less than 1 percent deviation. Environmental requirements mandated water as the drilling fluid and grout was not allowed in to the lake under any circumstances. The shafts were videotaped and the breakout locations were examined using an underwater remotely operated vehicle (ROV) to verify shaft locations and rock conditions, and to guide placement of pneumatic packers to ensure grout did not transmit to the lake during the steel liner installation. In anticipation of the invasion of quagga mussels, the shaft design included an allowance for a chemical dosing system and a copper-rich alloy at the exposed portions of the steel liner.

Jan 1, 2011

By A. J. Kraemer

Few important improvements other than the development of cracking processes were made in technical petroleum refining from 1914 to 1919. Refiners were concerned mainly with enlarging their plants and erecting new plants to meet the growing demand for petroleum products. Shell stills operated as a unit or arranged in series for progressive or continuous distillation were the prevailing distillation equipment. Some improvement was made in condensers, but in most refineries of the period coils of pipe immersed in tanks of water were used to condense vapors and cool liquid products of the stills. Heat exchangers to conserve heat and reduce costs were more highly developed at California topping plants than at other plants. In this connection Wadsworth3/states: It is regretted that information concerning the operation of topping plants with eastern and Middle West oils is not available. The writer carefully canvassed the Middle West, but did not find a plant where operation had progressed beyond the early experimental stages and reliable figures could be furnished.

Jan 1, 1941

By Edgar L. Weinberg, W. Horatio Brown

The Austinville-Ivanhoe lead-zinc deposit occurs in the Lower Cambrian Shady dolomite. This deposit is located in southwestern Virginia in the faulted and folded Appalachian Valley and Ridge province. The ore bodies resemble the chimmey and manto deposits of northern Mexico and are formed by replacement and filling. They are confined to certain favorable zones of the Austinville and Ribbon members of the Shady. Structural and stratigraphic factors combine to control the location and form of the ore bodies. In certain places secondary oxide enrichment of the zinc minerals has contributed to the economic development of the area. It is concluded that the ore is epigenetic and is deposited by hydrothermal solutions rising through the fault "plumbing." Classification is epithermal-telethermal.

Jan 1, 1968

By Jason J. Ballentine

This case study presents the results of a maintenance review of a soot blower system at a coal fired power generation station. The power generation station was following a ?repair when it breaks? maintenance strategy for its soot blowers. The efficiency losses incurred as a result of failures in the soot blower system and the resulting interruption and out of service time was found to have a significant effect on the plant output. The maintenance strategy for the soot blowers was reviewed using Reliability Cantered Maintenance and lifecycle simulation. This methodology provided visibility to the monetary implications of failures and allowed alternative types of maintenance to be assessed and where justified were added to a maintenance schedule in the Maximo work order management system. By reducing unplanned breakdowns the predicted reduction in efficiency losses was 45%.

May 1, 2007

By Jay F. Colinet

Respirable dust exposure has long been known to be a serious health threat to workers in many industries. In coal mining, overexposure to respirable coal mine dust can lead to coal workers? pneumoconiosis (CWP). CWP is a lung disease that can be disabling and fatal in its most severe form. In addition, miners can be exposed to high levels of respirable silica dust, which can cause silicosis, another disabling and/or fatal lung disease. Once contracted, there is no cure for CWP or silicosis. The goal, therefore, is to limit worker exposure to respirable dust to prevent development of these diseases. The passage of the Federal Coal Mine Health and Safety Act of 1969 established respirable dust exposure limits, dust sampling requirements for inspectors and mine operators, a voluntary x-ray surveillance program to identify CWP in underground coal miners, and a benefits program to provide compensation to affected workers and their families. The tremen­dous human and financial costs resulting from CWP and silicosis in the U.S. underground coal mine workforce are shown by the following statistics: ? During 1970?2004, CWP was a direct or contributing cause of 69,377 deaths of U.S. underground coal mine workers. ? During 1980?2005, over $39 billion in CWP benefits were paid to underground coal miners and their families. ? Recent x-ray surveillance data for 2000?2006 show an increase in CWP cases. Nearly 8% of examined underground coal miners with 25 or more years of experience were diagnosed with CWP. ? ?Continuous miner operator? is the most frequently listed occupation on death certificates that record silicosis as the cause of death.

Jan 1, 2010

By E. J. Gleim

[of- ac tore affecting the e -success of recent conveyor miningsystems forLt. extraction. 1 GL C ,_tfreedom shoot &apos;_)`u 2--ethe.1 is coal while e en othershot firers re:7 t _e&apos; _U-tin , w J, e coal .Z- 311.ing States conveyors because ;-.;lax .ca requires thatblasting be limited to when c .. men os. _o tend neces¬sary officials 1 s . re out c-z ,r 7t ...y e:e l z<: woes no t a -¬#to 1 C" such restriction on blasting conveyor miningbeen extendedWhere ere t ere. re no _ c: t&apos;_ _c tit-----! . kind cutlasting;,1CL?; C&apos;. _ z)carried anI-7LC. AT continuouslyHowever, unless et._&apos;0:, precations are taken under r&apos;t e , accidents, n is or such, as111 electricity r 1C- from.J--_,._.1t ,° =&apos;1?without usingholes, as well as numerous-o _&apos;1&apos;-1 -= e troublehe record of mineexplosions (some of themSo so _C&apos;_ °:&apos;,v 0f rock- dusting]

Jan 1, 1941

By JOURNAL SAIMM

SYMPOSIUM ON PELLETS AND GRANULES During October 1974, the Newcastle branch of the Australasian Institute of Mining and Metallurgy is to hold a symposium on pelletizing and granulation, with particular reference to the iron ore, fertilizer, and cement industries.

Jan 12, 1973

By M. Misra, I. A. H. Schneider

The flocculation of -38 pm calcite, hematite and kaolinite aqueous suspensions by the yeast Candida parapsilosis and products derived from rupture of the microorganism was studied. Flocculation of hematite suspensions by the microorganism and its derivatives readily takes place between pH 2.8 and 11.4. Maximum flocculation occurs at about pH 6.5. Flocculation of calcite suspensions by the microorganism and its derivatives readily takes place between pH 7.0 and 11.8. Maximum flocculation occurs at about pH 10.0. Flocculation of kaolinite suspensions was less than that for the other two minerals. However, a soluble fraction derived from the rupture of the organism functioned as a good flocculant for the mineral, albeit at an increased concentration, between pH 2.6 and 11.5. Maximum flocculation occurs between pH 6.8 and 7.2. An attempt is made to relate the behavior of the various systems to the surface characteristics of the minerals and the surface and chemical properties of microorganism and its derivatives. Experimentation used to evaluate the flocculation includes actual flocculation tests, microelectrophoresis measurements and scanning electron microscopy.

Jan 1, 1994

By Fred C. Turin, Jasinder S. Jaspal, Alan G. Mayton, William J. Wiehagen

Dump site injuries occur in all major mineral industries. Working in elevated areas near an edge is a common hazard for operators of off-highway mobile mining equipment. In this Information Circular (IC), serious injuries involving haulage trucks working at dump sites are examined for the period 1988 to 1997. Data were acquired from injury reports gathered by the Mine Safety and Health Administration (MSHA). The IC is organized into three sections. The first presents an overview of the frequency and severity of injuries. The second analyzes injury characteristics using MSHA-defined data fields and author-defined injury classifications. Key findings are discussed in the third section. In summary, 370 serious injuries were identified that involved trucks at dump sites, of which 26 were fatalities. Although haulage truck activities at dump sites resulted in a small proportion of the total number of injuries at surface mines, these injuries were much more likely to result in death or significant amounts of lost time than most other surface mine injuries. These findings support the belief that haulage truck activities at dump sites are worthy of continued study by those interested in improving the health and safety of workers at surface mines.

Jan 3, 2001

By S. Heukelman

Zincor uses O2 enrichment (up to 26% O2 in the fluidizing air) to increase the processing rate of zinc concentrates in the fluidized bed roasters. The aim of this study is to determine whether O2 enrichment can be reduced by introducing micro-pelletized concentrate into the feed blend, while maintaining current roaster feed rates and calcine quality. It was found that, with a load of 20% micro-pellets introduced into the feed blend, that O2 enrichment could be reduced by 60%. It was determined that entrained particles spend on average between 0.46 hour and 2.44 hour in the roaster, compared to particles remaining between 3.93 hour and 4.00 hour in the bed overflow. This compares well with a radioactive tracer test performed by Spira. The required reaction time for micro-pellets was found to be less than the residence time inside a Zincor roaster. The result achieved indicated that the average particle residence time inside the roaster was increased successfully in order to compensate for the longer reaction time required to roast micro-pellets at lower levels of O2 in the fluidizing air.

Jan 1, 2011

By J. G. Groppo, A. E. Bland, B. K. Parekh, W. F. Stotts

Many coal preparation plants discard fine coal (generally minus 100 mesh) because it is difficult to beneficiate economically. At the Kentucky Energy Cabinet Laboratory (KECL), the waste streams from several Kentucky preparation plants were evaluated for cleaning with counter-current column flotation. A series of performance evaluations were conducted using a 0.05 m (2 in.) internal diameter (I.D.) 7.9 m (26 ft.) high laboratory column. The objectives of these tests were to assess the performance in terms of recovery and percent ash in clean coal and to optimize the operating parameters relative to combustible recovery and grade. Refuse streams containing 30-50 percent ash were upgraded to 2-8 percent ash with Btu recoveries of nearly 90 percent. A pilot scale column flotation cell was installed at the Bell County Coal preparation plant. This pilot plant utilized a 5.79 m (19 ft.) high and 0.15 m (6 in.) I.D. column to verify the performance data of the 0.05 m (2 in.) I.D. column for two different waste streams. Performance evaluation and pilot plant testing results related to scale-up are discussed.

Jan 1, 1988

By Waterhouse J. D, Harris B. M

This paper briefly describes the construction in 1979/80 of a 70m deep trial open pit coal mine near Bowmans S.A. and describes more fully the hydrogeological aspects of the exercise. The primary purpose of the Trial Pit was to provide a large sample (700 tonnes) of coal for combustion tests to be carried out in West Germany and the United States of America. Consideration was given to obtaining the sample of coal by drilling and by shaft sinking as alternatives to open pit methods. It was expected that economic mining of the deposit on an operational scale could only be achieved by open cut methods and it was recognised that major uncertainties existed in planning such a mine in the deep unconsolidated multi-aquifer deposit. It was therefore elected to obtain the bulk sample by constructing a trial open pit, which would be closely monitored to provide as much data as possible for future planning of a full scale mine. The dewatering of the Trial Pit was achieved using 26 deep pumping wells, assisted in the later stages by several hundred well points. This was probably the largest dewatering project currently in operation in Australia.

Jan 1, 1981

Table 1.-Salient statistics of carbon black produced from natural gas and liquid hydrocarbons in the United States [ ]

Jan 1, 1967

By Virgil A. Bilyeu

The Pan American Mine, in southeastern Nevada, is about 26 miles west southwest of Pioche, Nevada, and about 266 miles southwest of Salt Lake City, Utah. The mine is located in the Comet Mining District, and since the ore occurrence is generally the same in the Comet and well known adjacent Pioche Mining Districts, the history of the two shall be considered the same. The Pioche District began about 1869 with the production of high grade gold and silver from fissure veins in the Cambrian Prospect Mountain quartzite. Peak production was reached in 1872 and then declined with sporadic production until 1924, when Combined Metals Reduction Co. shipped its first, complex sulphide ores mined from the CM bed at Pioche. Extensive ore bodies in this CM bed attracted interest in the same bed in the Comet District. Small pockets of high grade silver-lead were mined from fissures cutting the CM and other limestone beds above. Exploration in the CM beds at this time proved a large area of mineralization too low grade to be considered ore.

Jan 1, 1967

By R. C. Corey

Anticipating the need for convenient, economical, and safe means for disposing of combustible wastes contaminated with low-level activity, in connection with private and institutional uses of radioisotopes, the Atomic Energy Commission (AEC) has provided the Bureau of Mines with funds to develop an incinerator for this purpose. A prototype incinerator, designated hereafter as BOMAEC-30, was designed, constructed, and tested, based on fundamental and applied research investigations of the combustion characteristics of rubbish and sawdust, which will comprise the bulk of contaminated wastes. No radioisotopes were used in the tests; the objective was to remove as much particulate matter from the products of combustion as possible. The prototype unit was designed to burn 30 pounds per hour, using 100 percent over fire air admitted tangentially in an all-metal, cylindrical combustion chamber. The gas-cleaning system consisted of special fabric bags and absolute filters.

Jan 1, 1962

By B. P. Bellport

This paper summarizes the Bureau of Reclamation&apos;s experience in the use of boring machines to excavate six major tunnels on the Bureau&apos;s water resources development projects in the western United States. The summary of experience is presented as a compilation of brief case studies for each of the six tunnels. Each compilation presents data on the tunnel dimensions, geological characteristics of the excavated rock, the tunneling machine used, machine operation, muck handling, method of tunnel support, ventilation system, and related information. The listing of the six tunnels in Table 1 reflects a diversity of tunnel lengths and diameters. However, despite this diversity of dimensions as well as the variety of rock encountered during excavation, the six tunnels have one major characteristic in common: their excavation was significantly expedited by the use of boring machines. Beginning with the 10,079-foot-long Tunnel No. 1 on the Navajo Indian Irrigation Project in New Mexico - the Bureau&apos;s first tunnel to be excavated by a boring machine - the boring machines, or "moles," have demonstrated their effectiveness in rapid and economical tunnel excavation. Tunnel No. 1, virtually 2 miles long, was bored through in 9 months, an unprecedented achievement in Bureau engineering experience, as compared with tunnels previously excavated by conventional means. Boring of the 45,630-foot-long Blanco Tunnel and the 26,610-foot-long Oso Tunnel, both on the San Juan-Chama Project in Colorado, set world records in rates of excavation,l/* Two days of exceptional progress highlighted the

Jan 1, 1970

By W. D. Blackburn

If there is a single key to managing a mineral extraction company, it is the control of productivity. American labor costs, in general, tend to be in the range of 10%-15% of total costs. American coal mining labor costs, however, exhibit ranges of 30%-60% of total costs. Is it any wonder that the industry finds itself at a competitive disadvantage? When labor costs take as much as sixty cents of every dollar of revenue, there is little room for profitability. The American coal mining industry must set as a long range goal the reduction of labor costs to the 10%-15% range of total costs in order to be competitive.

Jan 1, 1986

By A. T. Stroebel

Diatomite deposits, the skeletal remains of tiny aquatic plants called diatoms, are found in many parts of the world. Only a few of these de- posits are of commercial value. Open pit mining is used in nearly all deposits now being worked. Processing methods range from simple drying, crushing, sizing and packaging to carefully controlled and highly sophisticated calcining and air classification procedures, employing the latest control and testing techniques. The major uses of processed diatomite are in filtration as filter aids and fillers and extenders.

Jan 1, 1979

By David Nicholls

?Overview of New Afton ?Reserves and Resources ?Geology and Mineralization ?Exploration ?Capital Project Development to Date ?Mine Development ?Processing ?Construction ?LOM ?Health, Safety, Environment and Social Responsibility Overview of New Afton ?Fully owned by New Gold Inc ?Large gold-copper porphyry deposit, amenable to block cave mining, production commencing in 2012 -1 million ounce gold reserve -1 billion pound copper reserve -Estimated 13 year mine life ?Low operating cost ?Estimated capital expenditure requirements -Spend to date ?US$200million -Remaining to be spent ?US$400milllion ?Robust economics ?Excellent location and infrastructure ?Significant cash flow contributor for the Company

May 1, 2010

By W. H. Gross

To pollute means to make impure or unclean. We tend to forget that man defecates, urinates, sweats, expectorates and exhales and in himself is a beastly little pollutor-but then so is Mother Nature! The object of this paper is to try to put what man and nature do into perspective. The facts indicate that although man may sweat a little, Ms. Nature is by for the greatest pollutor of all.

Jan 1, 1979