Search Documents

By Ralph J. Holmes, Victor Sharp, Steven J. Spencer, Kevin J. Davey, Jonathan J. Campbell, Peter L. Phillips, David G. Barker

"Improved measurement tools for monitoring and control of AG/SAG mill performance have a high level of interest in industry. Historically, acoustic emission monitoring has been widely used on SAG/AG/ball mills and hydrocyclones to provide new information on the conditions inside these devices affecting their performance. The current work was focused on a new technique using surface vibration monitoring of a number of pilot-scale and production-scale AG/SAG mills to yield insights into the events occurring in the mills. The development of relationships between signal analysis outputs and mill operating conditions can be used for soft-sensor measurement of mill process variables. The technique used an array of accelerometers mounted on the mill lifter bolts linked to a fast data acquisition system which monitored the surface waves generated during operation. Details of the system are presented. Mill operating variables were adjusted systematically to provide a wide range of operating conditions for surface vibration signal collection. The experimental approach is discussed.The signals acquired during the experiments were analysed using a range of techniques. The results show that strong relationships exist between measured vibration power (both total power and within certain frequency bands) and mill load level/power and mill speed. A new method for extraction of power spectral density and band power information on features of interest in a mill rotation cycle is also presented.These results show that single sensor analysis information from the surface vibration system can be used as soft sensor inputs for monitoring process variables such as mill load that until now, have not been reliably measured. System outputs also show considerable promise in the area of condition monitoring. An example of the signal analysis output is presented showing elevated vibration levels in an area with higher resultant wear. Eventually, it is considered that outputs from this system for process variable and wear condition monitoring will be key new inputs to an online AG/SAG mill monitoring and control system."

Jan 1, 2003

By Ernest A. Curth

A 3-month study in 1971 of the Essen Roof Support and Rock Mechanics Research Center's program of roof and support evaluation included 25 mine trips. German miners must adopt mining methods and environmental control measures involving methane drainage and water infusion to improve productivity under severe natural conditions. Pressing problems in ground control must be solved such as cavities in front and above the supports at longwall faces and excessive convergence in gate roads. The Center developed automatic data processing methods to quantify the results of roof and support surveys and to establish criteria. Another approach to ground control is the study of mine models. The Center's laboratory has the facilities to test elements of powered roof support and whole assembled units. Face automation and roof control by powered shields are novel developments that are under close scrutiny in the field as well as in the laboratory. Though the Essen Center's roof and support evaluation techniques are tailored to the needs of the coal mining industry of the Federal Republic of Germany under conditions vastly different from those in the United States, some application may be found here, for instance, monitoring faces and roadways and preventive maintenance of hydraulic systems.

Jan 1, 1974

By Pratheesh George

Solid state galvanic cell with CaF2 as the electrolyte was employed for determining the thermodynamic properties of Nb-Al binary alloys in the temperature range of 973-1073 K. The activities and activity coefficients of Al in NbAl3 were determined. The experimental procedure and the design and construction of the experimental setup have been also explained in detail. Aluminum activity in NbAl3 increased with increase in temperature and shows a strong negative deviation from ideality. The activities of aluminum in NbAl3 were determined to be 0.0165 and 0.0289 at 973 and 1073 K respectively. The stability of NbAl3 has been compared with other available intermetallic systems.

Jan 1, 2006

By Charles Vaught, Jeff Duncan, Michael J. Brnich, Lisa J. Steiner

This document contains most of the materials needed to use the exercise. The main part of the document is the instructor's copy. It tells how to use the exercise, presents the objectives, the master answer sheet, the scoring key, and discussion notes to be used following the exercise. The next section summarizes results from field tests of the exercise, and reports the miners' evaluation of the activity. The last part of this document is three appendices. Appendix A is the exercise problem booklet. This booklet can be duplicated locally. The booklets are reusable. One is needed for every person in the classroom. Appendix B is the answer sheet. Copies of this answer sheet must have the latent image (invisible) ink answers that appear in Appendix C printed on them.3 Answer sheets are consumable. One is needed for each person or each small group of persons who work the exercise. Exercise Summary Read this section first. It determines if the exercise is appropriate for your classes. If you choose to use the exercise, examine the table of contents and review the remainder of this document. Type: Latent image Audience: Remote control and extended cut miner operators and face crews Length: Eight questions (30 minutes for administration plus 30 for discussion) Skills: Remote control mining procedures including remote control mining, taking extended cuts, resetting breaker on mining machine, and setting timbers. Communicating mine conditions, influencing safe behaviors when mine conditions are less than stable Location: Underground coal mine, four section continuous mining operation Average seam height is 48 inches Problem: Your regular job is on the general labor crew at Cripple Creek #9 mine, a four section continuous mining operation. The mains are 9 entries wide and panels are 5 entries across. You and the rest of the crew had annual refresher training about 3 months ago. For the past few days you have been sent to 2 South panel to fill in as the third shuttle car operator. This morning, however, your buggy is down. The face boss asks you to get the scoop and take seven or eight timbers to the number 5 entry because the last shift got off sight line. The miner will be working in entry 5 while the bolter crew pins entry 4. When you get up to the face you see that Mo, the remote control continuous miner operator, has rounded off the left inby corner in order to make his first cuts in the right hand rib. Now, he has squared around enough so that you and Red, the miner helper, can set some posts on the corner. The two of you set posts along the left inby rib of #5 entry while the shuttle car operator waits. You are in a tight spot when Mo decides to start mining. You must decide where the best place is to stand for safety and to be out of the way.

Jan 10, 1999

By Edith Lafontaine

Modern underground mines operate fleets of mobile production equipment including drill jumbos, long-hole drills, load-haul-dump machines, trucks and bolters. Their availability has a substantial impact onto production cost and thus onto mine profitability. Through appropriate collection of pertinent data and information, use of adequate performance measures and their analyses, mine operators can identify the most promising and cost effective opportunities to get more from their equipment and to reduce the overall cost. This paper presents results of the study aimed to review and analyse means and measures used to quantify equipment availability and its contributing factors (reliability, maintainability and maintenance support) in several Canadian underground mines. It overviews current reporting procedures, sources, quality and quantity of the data and information collected as well as examines performance measures and their definitions used by the surveyed mines. Problems concerning data acquisition as well as meaningfulness and usefulness of the above mentioned metrics are also discussed. The paper concludes with some suggestions and recommendations concerning several aspects of equipment availability assessment. It is believed that the latter may become a more useful tool for mine operators in their efforts to reduce production cost than it seems to be the case at present.

May 1, 2007

By Richard L. Sanford

This report summarizes the results of the development of a Directory of Computer Programs Applicable to U.S. Mining Practices and Problems. The Directory includes a sampling of computer usage in operating and manufacturing companies, consulting firms, computer companies, research organizations, universities, and various U.S. government agencies. References to computer applications throughout the mining industry are presented as well as comments on the availability of programs to interested organizations or individuals.

Jan 1, 1977

By Tim O’Neil

The US Bureau of Mines and the Santa Cruz Joint Venture (SCJV) are working on a production-scale, in situ copper recovery project in Arizona. The research is being conducted at the Santa Cruz site, located 11.2 km (7 miles) west of Casa Grande, AZ (Fig. 1). Santa Cruz is a 1.36-Gt (1.5 billion st) porphyry deposit averaging 0.6% Cu, of which 65% is oxidized, concealed beneath post-mineral alluvium at depths of 365-914 m (1500-3000 ft). The Bureau and the SCJV will evaluate in situ mining as a method for extracting copper from this previously unmined deposit. Research objectives of the Santa Cruz project are: - to demonstrate that an in situ research test can be operated in an environmentally acceptable manner ; and * to operate an in situ well pattern long enough to develop information on copper recovery and economic feasibility data. In situ mining of copper from undisturbed deposits has not been attempted commercially. There are several potential advantages with in situ mining: less exposure of miners to hazards, lower pital costs for the mine and plant and lower operating costs. In addition, there are no pits, dumps or tailings, which means less environmental impact.

Jan 1, 1991

By W. M. Hart

Business Process Improvement (“BPI”) Change to Survive “It is not the strongest of species that survive, nor the most intelligent, but the one most responsive to change.” [Charles Darwin] “If you want to understand something, try to change it.” [Kurt Lewin, social scientist] Many companies have tried one or more process management initiatives. Each effort may help develop a culture that is more receptive to change. Executive Management needs to be unwavering in support of change with systems and structures, staffing, development of people, measures, with incentives and rewards. General Electric developed principles for quality change management that are necessary for effective, continuing Business Process Improvement (BPI). Change Acceleration Process (“CAP”) One of the tools General Electric developed has been used successfully by companies around the world in a wide variety of industries. This tool, named Change Acceleration Process (“CAP”), is designed to improve acceptance of change. Acceptance is the method by which the creative energies of the workforce can be fully tapped. Over time, every employee receives CAP training at least once, and in many instances three (3) or four (4) times, and will work on one or more High Performance Teams. Thus, BPI can achieve and maintain its goals. The CAP tool focuses on: • Leading Change • Creating a Shared Need • Shaping a Vision • Mobilizing Communication • Making Change Last • Monitoring Progress • Changing Systems and Structures

Jan 1, 2006

By C. H. Bucknam

Principles of Green Chemistry provide useful guidance for sustainable mineral process development. Laboratory bench scale testing was carried out using pregnant cyanide leach solutions, and a number of commercially available mercury precipitation reagents were compared using jar testing to determine the most efficient and selective reagents for mercury precipitation. The most efficient reagent identified was sodium polymeric thiocarbonate (NaPTC).Coagulation experiments with fine diatomaceous earth resulted in a stable precipitate, with good settling properties. On line monitoring of the mercury in solution is recommended for process implementation to conserve reagent removing approximately 90-95% of the mercury with minimal silver and negligible gold losses.

Jan 1, 2004

By Douglas E. Pollock

Recent NIOSH published information has shown an increase of rapidly progressive coal workers? pneumoconiosis (CWP) in the southern Appalachian coal region (SAR) of the U.S., despite the fact that compliance data indicates that most coal miners have been exposed to coal mine dust concentrations below the statutory limit of 2 mg/m³. While the exact cause of these elevated CWP levels in the SAR has not been established, several factors may be contributing to the increase in occupational lung disease among coal miners. The mining of high rank coal is known to lead to higher CWP rates, and this type of coal is mined in a portion of this region. Also, a high percentage of the mines in the region are on reduced dust standards because of the high silica content of the airborne dust resulting in miners possibly being exposed to excessive amounts of respirable silica dust. Exposure to excessive amounts of respirable silica dust can lead to silicosis, a disabling and potentially fatal lung disease. NIOSH?s Respiratory Hazards Control Branch has been investigating the possible causes that would account for the observed higher trends in disease progression through literature review, data analysis and in-mine surveying. The investigation to date has revealed that underground mines are faced with cutting large amounts of rock in order to maintain haulage clearances. Cutting rock not only increases the potential for silica exposure, it increases the requirement for machine maintenance, which was a concern observed during dust surveys conducted by NIOSH. Over half of the mines operating in the SAR are on reduced standards due to high silica content. Adequate face ventilation of the continuous miner and roof bolter and limited down-wind operations from the miner are also issues of concern and items that require the constant attention of miners operating in these conditions.

Jan 2, 2010

By George A. Morgan

The 53 countries that constituted Africa in 1991 accounted for a significant portion of total world output of a number of mineral commodities. However, total output for the continent declined for many major mineral commodities produced compared with that of 1990. Also, Africa's share of total world output of these commodities generally declined. (See tables 1 and 2.) The most conspicuous declines were for cobalt and copper owing to mining and metal processing difficulties experienced by the world's two largest cobalt producers, Zaire and Zambia. Phosphate rock output declined primarily owing to a sharp fall in production from Morocco, also a leading world producer. Morocco's state corporation for phosphate production experienced marketing problems, leading to the decline.

Jan 1, 1993

The coal-bearing strata of Oklahoma occur in the eastern part of the state over an area of 14,500 square miles, 20.7 percent of the state's total area. Commercially valuable deposits of bituminous coal cover about 8,000 square miles in seams ranging from ten inches to five feet thick. Estimated reserves in Oklahoma are 1.6 billion tons, representing 0.3 percent of U.S. coal reserves. The vast majority of coal mined in Oklahoma used in a single power plant within the state. Oklahoma gained primacy when its regulatory program was conditionally approved January 19, 1981. Authority for the state to administer the Abandoned Mine Land program was granted January21,1982. On April 30,1984, the Office of Surface Mining substituted direct federal enforcement of the inspection and enforcement portions of the Oklahoma program. This substituted enforcement was based upon a finding by OSM that Oklahoma had not operated the inspection and enforcement portions of its program effectively. As of January 1, 1986, Oklahoma inspection and enforcement authority was reinstated. Full program authority was granted to Oklahoma on January 14, 1986.

Jan 1, 1992

By James W. Reil, Douglas A. Anderson, Steven L. Burchell

A total of 26 full-scale production blasts at three sites were extensively monitored with sophisticated instrumentation systems to determine the benefits of more accurate detonators. The new and more accurate MS electric Masterdet detonator was tested against conventional detonators to determine any increase in productivity outputs. All blast design parameters between paired blasts were kept as constant as possible with the only difference being the inherent accuracy of both detonator systems.

Jan 1, 1986

By J. -C. Tricket, W. A. Düweke, S. Kock

The high-resolution three-dimensional (3-D) seismic reflection data acquired for Impala Platinum between 1998 and 2002 in the western Bushveld Igneous Complex form an integral part of Impala?s mine planning and development programme. These data are of sufficiently high quality to provide unprecedented 3-D models of the geological structure of the Merensky Reef and UG2Chromitite Reef, from which the mine deduces the size, geometry and distribution of mineable blocks. Conversely, the seismic data details zones of un-mineable ground caused by structural disturbances in the form of potholes, fault zones and pegmatoid intrusions. Furthermore, variations in dip and strike are well imaged, allowing the mine planners to optimize the mine design and layout. Current interpretation work is focused on enhancing the accuracy of these geological model seven further through the analysis of ?seismic trace attributes.? Preliminary testing on the Impala Platinum 3-D seismic volume has shown that attribute analysis has the potential to illuminate a number of geological reef disturbances that are otherwise ?invisible? in the original seismic time volume. Potential areas of improvement include inter alia: ?Improved definition of major fault zones ?Improved definition of zones of reef depression (?slumping?) ?Identification of reef terracing and/or reverse dip.. Keywords: 3D reflection seismics; Impala Platinum Ltd; seismic attribute analysis; Seismic Micro Technology (SMT); rock solid attributes; dip-azimuth; instantaneous phase and similarity.

Jan 1, 2004

By Kevin J. Palmer

The introduction of the National Instrument (?NI?) 43-101 Standards of Disclosure for Mineral Projects has led to some very specific requirements to reporting a Mineral Resource estimate for mineral projects to the public. There are elements of the Mineral Resource estimate that are based on the qualified person (?QP?) completing the work to accepted industry practices and applying their relevant experience. There is no document that defines what is considered the accepted industry practices. There are guidelines provided by the Canadian Institute of Mining, Metallurgy and Petroleum (?CIM?) but, in general, the industry practices are dynamic and often different QPs will estimate the same mineral project in different ways. This sometime happens on exploration projects as they proceed from one study to the next. The focus of this paper is to provide a review of some of the current practices that are published in Technical Reports (Preliminary Assessment to Feasibility studies) with respect to classifying a Mineral Resource as Inferred, Indicated and Measured and the grade interpolation and modeling methods, data support (i.e. geological drill hole spacing) and validation methods employed.

Oct 1, 2010

By C E. J de Ronde

Most of the world's economically significant volcanogenic massive sulphide (VSM) deposits are considered to have formed in submarine arc and backarc settings. While the Kermadec-Tonga arc is an excellent example of an intra-oceanic arc setting, it remains largely unexplored in terms of submarine mineral resources. More than half of this arc (~1400 km of the >2500-km-long feature) lies within the EEZ of New Zealand, where it is defined by at least one sub-aerial and 33 submarine volcanoes. The NZAPLUME (New Zealand American PLUme Mapping Expedition) cruise of March 1999 provided a systematic assessment ofhydrothermal activity on the southernmost 13 submarine volcanoes along the southern Kermadec arc. Using prospecting techniques based on the physical and chemical detection of hydrothermal plumes, we discovered that more than half (7 of 13) of the southern Kermadec volcanoes host one or more active hydrothermal systems at depths ranging between <200 to 1800 m. Chemical results show that the fluids discharged are compositionally diverse among volcanoes and between sites at a single volcano. Plumes over more than half of the volcanoes are gas-rich (He, CO2, H2S) relative to mid-ocean-ridge (MOR) plumes. In addition, most sites are highly enriched in Fe, yielding Fe/Mn values that far exceed those for MORs. One interpretation consistent with these observations is compositional overprinting by addition of magmatic fluids, which are typically highly enriched in gaseous and ionic components. Regardless of the source, it is clear that the ligands (HS-, Cl-) required to efficiently transport base (e.g. Cu, Zn, Pb) and precious (e.g. Au, Ag) metals to the seafloor are abundant in Kermadec arc fluids. We conclude that modem analogs of VMS deposits are likely forming at multiple sites along the Kermadec arc and within the EEZ of New Zealand.

Jan 1, 2000

By L. H. Michaud

"Albian Sands Energy (ASE), an oil sands surface mining and extraction operation, is currently undergoing start-up and is scheduled to ramp-up to full production by mid-2003. Startup includes the selection and implementation of over 75 IT systems or computer applications which include: engineering applications; systems required to control mining activities, maintenance, the processing plant and utilities; and also systems required to run the company, such as human resources, finances and inventory/ warehousing.This paper outlines the processes used for the selection, implementation and integration of these systems in order to optimize the use of information and to meet the technical, business and IT requirements of the company. The first step in ASE’s approach to identifying system requirements is the development of a business activity model, outlining all tasks involved in running the operations. The computer applications required to accomplish each task are then identified by having the IT team work closely with each technical and business unit. Historically, at some companies, the selection of systems has been led by the IT team or by consultants, with little input from the technical or business units. Typically, this results in products that do not meet the company’s expectations. To ensure a more positive outcome, ASE believes that it is imperative that the company’s technical and business people be closely involved in the selection process.Integration of the IT systems is also key, including linking all applications through a data warehouse and EDMS. Over 120 required integrations have been identified. This ensures the storage of all data in only one location, data security, and easy data and document retrieval for all requirements throughout the company"

Jan 1, 2003

By Rachel Bernau

Water wells, aquifers, and pipelines rarely incur damage from nearby blast vibrations. Extensive ground vibrations may cause a drop in the water table thereby changing an aquifer’s structure or drying up a well. Studies on the reactions of aquifers and water wells have been performed in Montana, North Dakota, and the Appalachia Coal Region. All of these studies reported that vibrations did not change the properties of the monitored aquifers and water wells. Rather, evidence suggests that any incurred damage was caused by block motion and downsloping.

Jan 1, 2001

By R. K. Rajamani, A. Datta

An appropriate scale-up methodology is very useful for ball mill design and optimization of the grinding circuit. To date, the scale-up is based on the selection and breakage function model using lab mill data. However, a major drawback of that approach is that the charge motion in a lab mill is vastly different from that in a large industrial mill. Therefore, in the methodology proposed here, first the energy of individual collision in the mill is computed employing the discrete element method (DEM). Then the breakage of particles as a function of collision energy is studied in a separate experiment. Together, this information constitutes what is known as collision energy based population balance model. The appropriateness of this model is shown for different batch grinding mills.

Jan 1, 1999

By M S. Stern, R Aguila

To control direct blasting costs many open pit mines dewater and line wet blastholes before loading them with ANFO or Heavy ANFO blends of explosives. The plastic lay-flat tubing used for these liners can be punctured during loading and allow water to partly dissolve and desensitise the explosive column which reduces blasting performance.

Jan 1, 1997