Search Documents

By Valentine Chanturiya, Irina Khabarova, Maria Ryazantseva, Igor Bunin

"XPS investigations of the influence of HPEMP - treatment duration on the surface composition for natural chalcopyrite and sphalerite are described. HPEMP is a video pulse with a nanosecond front lasting between 5 and 10 ns. The electrical field component can reach 30 kV, whereas pulses repetition frequency is 100 Hz. In general, the formation of metal-deficient surfaces, polysulphides or elemental sulphur and oxides/hydroxides, were determined during the treatment for both sulphides as well as the essential differences of the way of mineral surface transformation during the treatment. The chalcopyrite surface shows the formation of elemental sulphur under the HPEMP treatment at 103 pulses while appearance of unstable sulphite species was detected at the chalcopyrite surface within 5 seconds (0.5•103 pulses) under the same treatment conditions. The results indicate that the quantity of adsorbed water (at.%) is changed considerably during the HPEM - treatment depending on treatment duration for both minerals. The concentration of water onto the chalcopyrite surface decreased during 30 seconds (3•103 pulses) of the HPEMP - treatment and it rose after the treatment at 5•103 pulses. The inverse dependency was obtained for sphalerite surface. Single mineral flotation tests have shown the significant increasing of the minerals recovery."

Jan 1, 2014

By Stephen Northey, Nawshad Haque, Terry Norgate

"Life cycle assessment (LCA) is a recognized tool to evaluate various processing routes for metal production. Declining ore grades and higher specific energy requirements for primary metal production put greater emphasis on recycling. Greenhouse gas (GHG) emissions of steel and aluminium metal production were quantified with recycling scenarios using material recovery facility (MRF) data from the database of SimaPro LCA software. The GHG footprint of the MRF is relatively minor compared with that of associated transport during collection (i.e. 10 times more than MRF) of curbside recyclable material. Additionally, if the bulk recyclable material is sent overseas (i.e. Australia to China) from the MRF for further processing, the GHG footprint of shipping can significantly be larger compared with the sum of the collection and MRF (assuming electricity is from same source). Thus opportunities exist for reducing GHG emissions from secondary metal production if it is processed close to the MRF.IntroductionIt is a challenge to recycle metals significantly, although theoretically infinite recycling is possible due to their elemental nature. Leaks from the metal stocks in society occur through corrosion, wear and dispersive uses, or via land filling or similar activities that return metals to the earth. In order to provide a technically sound and transparent assessment of metal recycling, a methodology such as life cycle assessment (LCA) should be used. By taking a life cycle perspective, the beneficial recycling properties of metals can be evaluated in a manner that enables appropriate comparisons with other materials or product systems that do not have recycling loops. In practice, mixtures of primary and secondary metals are often used in new products, and also at the end-of-life various processing methods are used for recycling.The difficulty of introducing recycling into LCA is to set the right boundaries for the different flows ending in different product systems. It is a question of which observed material flow belongs to the first product system and which one to the second or subsequent systems. Recycling can be part of any product LCA. However, it is often a complex issue which requires specific considerations. As pointed out by Yellishetty et al. and Birat et al. [l, 2], LCA practitioners are left with much freedom in allocation of environmental burdens to account for recycling, thus making subjective judgments on recycling and allocation of credits to recycling. This often makes it difficult to compare the results of LCA studies conducted by two different practitioners even on the same processes. As LCA is often used to define policy in government, business and society circles, it should be based on a sound, objective and unbiased description of recycling."

Jan 1, 2014

By Abdolreza (Reza) Osouli

Determining the roof stability condition of underground coal mines in the Illinois Basin is sometimes very challenging. The roof stability of Illinois mines are mostly affected by two types of shales: Anna Shale and Energy Shale. These layers are sometimes weak in parallel bedding when subjected to horizontal stresses. The roof rocks in the Illinois Basin are are typically more moisture sensitive than the other coal fields. In this study the geotechnical properties of some of the shale units as well as limestone layers will be presented. The geotechnical properties of roof rocks consist of moisture content, unconfined compressive strength, slake durability, indirect tensile strength, and point load tests (Axial and Diametral). The correlation of indirect tensile strength versus diametral point load strength as well as unconfined compressive strength versus axial point load test are explored and discussed. These correlations will help in identifying the roof mass index and planning appropriate roof control measures. This study also evaluates the application of CMRR rock mass index for an Illinois coal mine.

Jan 1, 2014

By Yizhong Yuan, Dao Li, Nannan Xue, Tao Liu, Yimin Zhang

A new multi-stage counter-current circulation leaching process for extracting vanadium from stone coal was proposed, and the main factors on multi-stage counter-current circulation acid leaching process were investigated. The results show that the vanadium recovery could reach 86% under the conditions of sulfuric acid concentration of 4 M, liquid to solid ratio of 2 mL/g, temperature of 95 °C, reaction time of 60 min, mean particle size of 125 µm and circulation acid leaching stage of three. The losses of vanadium in acid leaching solution appeared during the four-stage acid leaching process. The strong adsorption performance of new formed KAl(SO4)2(H2O)12 crystal was main reason.

Jan 1, 2014

By B. W. Zhao

Quantitative analysis of minerals composing in ore is primary in process mineralogy, a veracious quantification and analysis is very crucial to optimize or design a beneficiation process, especially for a low grade and complicated ore. This paper will discuss a SEM-EDS based quantitative analysis developed in JKtech Australia through an example from Jinchuan lean ore. For a low grade, com-plex intergrowths and texture lean ore, chemical phase analysis of value minerals and identification by optical microscope are very essential, unite the SEM-EDS based quantitative analysis, we can understand exactly the lean ore, explain and quantify the process performance.

Jan 1, 2014

By Yuqing Feng, Ping Fang, Dezhou Wei, Zichuan Guan, Shuling Gao, Baoyu Cui

"Air core, as an inevitable phenomenon of rotational flow field inside hydrocyclone, has a major impact on hydrocyclone’s separation characteristics. The air core formation process, its structural features and its influencing factors were investigated systematically in this paper. Numerical study on the air core of a f50 mm hydrocyclone was carried out using a commercial computational fluid dynamics (CFD) modelling software package ANSYS/Fluent with the selection of Reynolds Stress Model (RSM) for the turbulence model and Volume of Fluid (VOF) for capturing the air-liquid interface. Physical experiments were conducted under the same geometry and operation conditions and the particle image velocimetry (PIV) technology was used to measure the liquid flow. The CFD results are compared with the experimental measurement with good agreement demonstrated. The air core was formed generally at around 0.7 s, air outsides of the air core was eliminated completely after 1.7 s. The centreline axial velocities and the water blocking hydrocyclone simulations showed that air of the air core entered the hydrocyclone from the underflow area and exhausted from the overflow area, but there was also some air flowing into the air core from the overflow area. The largest swing of the air core occurred on the top of the underflow pipe, and a protuberance similar to the shape of Adam’s apple appeared when the air entered the vortex finder. CFD simulation results also showed that the air core diameter was decided by axial position and parameters of hydrocyclone. The structural parameters have more effects on the air core diameter than the operational parameters."

Jan 1, 2014

By Seffen Leppla, Rolf Katzenbach, Matthias Seip

"Abstract The economic and safe design of deep foundation systems in difficult soil conditions is based on a reduction of construction material used, construction time spent, energy consumed and a high-level modelling of the soil-structure-interaction. The special foundation system Combined Pile- Raft Foundation (CPRF), in-situ load tests on the construction site and a sufficient soil investigation allow cost optimised constructions. In any case at challenging projects the observational method has to be applied for verification and quality control of the design. Regarding the 4-Eye-Principle as basis of the quality control management an independent peer review of the planning, design and construction phases is the guarantee for safety, serviceability and optimisation of all projects. Main execution standards for the construction of deep foundations based on the Eurocode 7 are summarised and discussed. The paper presents the basics of the safe and qualified design and construction of foundation systems including quality assurance. The application in engineering practice is shown on achallenging project of high-rise buildings with difficult boundary conditions.IntroductionThe construction of deep foundation elements in inner cities are special challenges due to the limited space for the construction works and the effects on existing buildings (Figure 1).An economic and safe design of deep foundation systems in difficult soil conditions is based on the following main aspects:•,qualified experts for planning, design and construction•,interaction between architects, structural engineers and geotechnical engineers•,adequate soil investigation•,design of deep foundation systems using the Finite-Element-Method (FEM) in combination with•,enhanced in-situ load tests for calibrating the soil parameters used in the numerical simulations•,quality assurance by an independent peer review process (4-eye-principle) combined with theobservational method if necessary"

Jan 1, 2014

By W. P. Nel

The introduction of the Higher Education Qualifications Framework (HEQF) and the updated Higher Education Qualifications Sub-Framework (HEQSF) has caused many South African university departments to rethink their programme qualification mixes (PQMs). In addition to the requirements stated in the HEQSF, a number of other factors have to be taken into consideration by a university department. These factors include, for example, the standards generated by the Engineering Standards Generating Body (ESGB) and subsequently approved by the Engineering Council of SA (ECSA) and the need to prepare students for various categories of professional registration with ECSA. This means that a university department has to choose the correct mix of Learning Programmes (LPs) from the HEQSF menu (which consists of 13 types of LPs). Preparing students for ECSA registration is aligned with the mission of universities, which is to teach and undertake research. However, research and the LPs associated with research go beyond the requirements for current ECSA registration. Assuming that universities offering engineering LPs would elect to prepare students for both ECSA registration and teach them to produce research outputs, which is mostly done at Master and Doctorate levels (NQF Levels 9 and 10), then it follows that academics are more interested in NQF Level 5 to 10 pathways (abbreviated as ?L5-10?) rather than the shorter pathways required towards professional registration. (For example, ECSA requires an NQF L5-L7 pathway for registration as a candidate professional technologist. This specific pathway may consist, for example, of two LPs, namely the 360-credit Diploma and the Advanced Diploma.) A L5-L10 pathway is a combination of LPs that will prepare the learner with a NSC (or equivalent qualification at level 4) to Doctoral level (level 10). Universities may choose at least four major pathways from the HEQSF menu in order to educate and develop students from NQF Level 5 to 10. However, various pathways towards registration in the category of candidate with ECSA are also embedded into these four NQF L5-L10 pathways, where each consist of a unique combination of LPs. Each of these pathways has an opportunity cost, and economic reality means that smaller departments may have to choose between the four pathways. Of all the many factors involved in PQM decision-making, the focus of this paper is on the HEQSF requirements, ECSA standards, and ECSA registration and how these, together with the various qualifications and educational LPs provided for by the HEQSF may impact on the PQM decision taken by engineering departments and schools at South African universities. The proposed four NQF L5-L10 ?pathway tool? for PQM decision-making may be useful for pointing out the advantages, disadvantages, and applications of the various pathways and combinations of pathways. Rather than deciding from a menu of thirteen qualifications and associated LPs, this article proposes that decision-making be undertaken on the basis of a menu of four main articulated ?NQF L5-L10? pathways (which also include one or more of the ECSA?s pathways for professional registration). The proposed ?NQF L5-L10 pathway? tool is an attempt to move one step closer to the aim of achieving a structured decision-making approach for designing a PQM at departmental level.

Jan 1, 2014

By C. J. Lenz

The results of prospecting operations involving geological data and a large number of geochemical determinations of the metal content of soil samples are plotted and evaluated by computer. Anomalous areas are identified in each type of environment by selecting probability or population boundary values from frequency distributions. The anomalies are plotted to permit correlation with geographical or geological features. Ranking of prospecting targets is made using geographic pattern, geology, absolute value and metal ratios. Three short case histories are presented.

Jan 1, 2014

By S. Banisi, O. Farshid, M. R. Rozebehi, A. Bahar, A. Arghavani, M. Mahdavi

At the rougher flotation circuit of the Miduk copper concentration plant (Kerman, Iran) five column cells (CISA) with the diameter of 4m and height of 12m using static mixer type (MicrocelTM) spargers have been installed. Based on the initial design, columns should accept a feed rate of 625 t/h with 80% passing size of 90 µm and solids concentration of 28% and produce 88% of the plant concentrate (i.e., 22 t/h) containing 32% copper. Due to mechanical and processing problems this objective was never realized and theses columns were remained out of operation from the commissioning time (2005). A new attempt with the aim of returning these cells into operation started in 2013. The results of an extensive study indicated that spargers plugging due to the entrance of small amount (2 kg) of coarse particles (up to 2.5 cm) because of usual problems at the plant environment was the main reason of columns non functionality. With a change in the recycle pump inlet design to the column, which prevented the entrance of coarse particles to the spargers, the operation of the column significantly improved. It was found that in order to have a stable operation of the columns at the rougher stage the feed rate for each column should be reduced from 125 (design) to 70 t/h. The air superficial rate had to be also reduced from 1.9 (design) to 0.6 cm/s. A period of 10 days of continuous operation showed that the carrying capacity was 0.23 (g/min/cm2) which was significantly lower that of the design value (i.e., 0.58). The gas hold up was found to be lower than 10% beyond which columns started to move to the turbulent state indicated by "boiling" froth. The average life time of spargers was determined to be 20 days which considered to be very short. The average recovery and concentrate grade of these columns were found to be 68% and 32%, respectively. The high wear rates of spargers, unusually high level of maintenance and supervision needed and instability of the operation made the plant managers not to use column cells as the roughers.

Jan 1, 2014

By M. Hawker, M. Kreuh

The mining and metallurgy industry is known to be of cyclical nature associated with price volatility. As such, some years are quite lucrative and other years require mining companies to tighten their belts. The field is a mix of junior, mid-tier, and major mining companies. One thing that is common to all of them is the time required and the cost to develop a flowsheet in accordance with best practices. Although a long list of factors can impact flowsheet development, this paper will include the impacts of: experienced metallurgical engineers and laboratories, representative samples for high quality and valuable testwork results, and following engineering development stages. The paper also provides typical time frames to complete selected engineering flowsheet development steps.

Jan 1, 2014

By N. I. Um

The coal bottom ash generated from coal-fired power plant accounted for approximately 5 mil-lion tons in Korea. Almost all of coal bottom ash was treated as reclamation of the landfill because of the content of unburned carbon. For recycling of coal bottom ash, effective removal of that is required. So, in this study, the removal of unburned carbon by flotation was studied with respect to adsorption ability in surface of a bubble in order to consider its application to recycle the coal bottom ash. The sample A, B and C were that the coal bottom ash contained 2.73%, 7.01% and 10.49% of the unburned carbon (UC) respectively. The column flotation was carried out for each time as the artificial injection of air at 10.0L/min flow rate and the reagents of 500g/ton kerosene and 80g/ton MIBC were used. The samples per water of 1.3 liters were from 0.5% to 4% (w/w.%). In the result of this study, the kinetic curves of unburned carbon adsorption from injected air bubbles were in-creased rapidly as equilibrium was approached; only 5 sec was needed from the sample A and B and 10 sec was from sample C. And the equilibrium isotherms of unburned carbon adsorbed by the infected air bubble from the sample B and C could appear the BET adsorption isotherm; MT = KMEEO/(EO-E)[EO+(K-1)E](K: adsorption affinity), but not the sample A that was not enough to express the adsorption curve.

Jan 1, 2014

By William Gleason

"During the past nine years the number of cellular phones connected to a network has increased from 34 percent of the world’s population in 2005 to 93 percent in 2014. These phones are powered by a combination of materials including elements such as gold, silver, copper and rare earths. And, as more parts of the world become connected to networks, the number of phones being produced, and the elements they will need, will continue to increase. The demand comes as prices for these commodities are slumping and access to the commodities is getting more difficult, technically and socially.These mobile devices have connected people around the world in ways that could not have been imagined two decades before, and, ironically, this communication has strengthened opposition to the development of the mines that produce the very materials they need to operate.In his keynote address to the 2014 SME Arizona Conference at the JW Starr Pass Resort in Tucson, AZ, on Dec. 8, 2014, John O. Marsden, SME President and president of Metallurgium, spoke to more than 500 attendees about the challenge to produce the materials that society needs while at the same time challenging the general public’s perception of mining that is often inaccurate and less than favorable.Marsden highlighted the amount of raw materials that will be needed not just for phones, but also for things such as automobiles, including electric cars, as a way to illustrate the importance of mining. Even so-called green products such as Tesla cars, which require about 317 kg (700 lbs) of aluminum, 13 kg (30 lbs) of copper and 36 kg (80 lbs) of cobalt for their eco-friendly batteries, will need materials mining provides.These are some of the numbers that the general public is often unaware of. They are part of the necessary things that mining provides for society but are rarely reported on. Instead, it is the accidents like the tailings spill at the Mount Polley Mine in British Columbia and at the Buena Vista Mine (Sonora, Mexico) that grab headlines and stick in the minds of the public, adding more challenges to an industry that already has its own complex technical challenges to deal with."

Jan 1, 2014

By Jianglan Duan, Steve L. Cockcroft, Andre B. Phillion, Carl Reilly, Daan M. Maijer

"In the aluminum alloy wheel casting process, careful design of the cooling system in the die and its operation (cooling channel timing) are critical to achieve quality and productivity goals. The problem is challenging owing to the cyclic nature of the process and the relatively large thermal mass of the die in comparison to the wheel. For a given die geometry, a set of constraints have been defined to ensure directional solidification and an objective function, based on cooling rate during solidification, has been defined to reach a target secondary dendrite arm spacing. The methodology presented in this study employs the commercial finite element package, ABAQUSTM, and an optimization module based on the open source library, Scipy. The developed methodology has been applied to a series of geometries and cooling system configurations, including a 2-D axisymmetric wheel and die assembly generated from a prototype die. Preliminary testing has shown that careful selection of the objective and constraint functions have made it possible to reach desired solidification pattern.TM- Dassault Systèmes Corp."

Jan 1, 2014

By Y. H. Wang

Micro-flotation tests of spodumene, beryl, quartz and feldspar have been carried out by using CaCl2 and FeCl3 as modifiers and a blending collector of oleic acid and hydroximic acid. CaCl2 shows efficient activation for spodumene when pH is above 11.5, and FeCl3 exhibits a markedly activation and good selectivity for spodumene in the range of pH 4 to 10. The main species of CaCl2 are CaOH+ and Ca(OH)2 when pH is above 11.5, and the main species of FeCl3?6H2O are Fe(OH)+2 and Fe(OH)3 during the pH range of 4 to 10. A selective flotation of spodumene and beryl from pegmatic ore had also been completed while using FeCl3?6H2O as activator and the blending collector. A bulk concentrate containing 1.087% BeO and 4.70% Li2O has also been obtained in the flotation of spodumene and beryl from pegmatic ore assaying 0.097% BeO and 0.45% Li2O, and the recoveries of BeO and Li2O in concentrate are 74.38% and 69.50% respectively.

Jan 1, 2014

By E. Scheepers

The process under investigation is the large-scale production of phosphorus. Gravity delivers the feed, consisting of pelletised apatite, coke and silica (in the form of gravel), to a submerged arc furnace through ten, evenly distributed feed chutes ensuring constant packed bed volume. Within this packed bed, solid-gas reactions are dominant in generating the gaseous product. These reactions, as well as the packed bed itself, were the main focus in the development of a fully three-dimensional CFD model in which fluid flow and energy distribution are represented as functions of chemical reactions, heating and melting of material and heat losses. The associated complex process interactions necessitated the creation of two process-specific, user-developed models that integrates accurate, thermodynamical data with computational fluid dynamics calculations, as well as reaction kinetics. The boundary conditions are provided by industrial measurements, and the key model parameters of reaction kinetics were obtained by laboratory experiments for different feed mixtures. Thirteen temperature probes installed inside the refractory lining of the furnace especially for this project allowed parameter fitting and validation to be guided within the constraints of real measurements. Simulation results reveal a thin, dome-shaped, reductive zone where conditions are optimum for maximum phosphorus recovery, as well as evidence of a thermal reserve zone similar to an ironmaking blast furnace located above this reduction zone. When compared to actual operating data, the CFD model can successfully predict the specific power consumption, the phosphorus in the slag and gaseous product flowrate under given operating conditions. This CFD model forms part of a larger project that aims to create a Dynamic-CFD hybrid control model.

Jan 1, 2014

By A. Alfantazi, M. Mahon

The current efficiency in zinc electrowinning is a key indicator of the performance in a cell house. This is typically measured by comparing the weight of the cathode to the electric current applied over the deposition period. This calculation can be cumbersome because the deposition history of each pulled set of cathodes will be unique. It will depend on the applied current and electrolyte conditions from onset of deposition until the cathode is removed and stripped. Not accounting for these can introduce errors to the calculated current efficiency. To track this history and reconcile the current efficiency, a time based computer process simulation was made of an industrial cell house. Two months of hourly recorded measurements from the cell house were input to the simulation, including current to the cell houses, concentrations, flow rate, and temperature of the purified leach solution. The simulation’s predictions of the concentration of zinc in the circulated, spent, and returned electrolyte all showed good agreement with the industrial data over the two months giving a validated zinc balance. The simulation was then tuned to predict the instantaneous current efficiency for all times, as well as the expected masses for the deposits given their deposition history.

Jan 1, 2014

By B T. Lusk, John J. Silva Castro

The signature hole method uses a convolution operation to predict the waveform of a production blast based on the record of a waveform produced by a single blast hole. Convolution is a mathematical operation on two functions, (generally the product) to produce a third one. Recent research communication and publications highlight a lack of discussion in the literature about the available methodologies to calculate the convolution for blast vibration prediction. The goal of this paper is to discuss and present in detail for students in ground vibrations from blasting, several techniques to calculate the convolution between signals when the signature hole method is used. Convolution is a straightforward operation when signals produced by each hole are assumed the same, however; variations in the signals from each hole in a production blast require a more complex convolution operation. A graphical procedure is shown in this paper to solve a convolution when signals vary hole-to-hole (as expected in a mining production blast). The graphical methodology was tested using a recorded blast event and the results were compared to the regular mathematical procedure (convolution) and the results from a commercial software used in the mining industry. Results show that the graphical procedure is in agreement with the results from the other two.

Jan 1, 2014

By David De Klerk, Maximilian Richter, Thirunavukkarasu Pathmathas, Indresan Govender

We consider the average power dissipation distribution for dense granular flows of an idealised mono-sized charge (5 mm glass beads) in a 300 mm diameter tumbling mill operated in the cascading-to-cataracting Froude regime. By combining the inherent frictional nature of particles within a dense flow regime and noting that tumbling mills are typically characterised by collisional and turbulent stresses, we derive the power dissipation distribution for athermal boundary conditions. The input data to the model (velocity, solids concentration, pressure and flow depth) are obtained directly from non-invasive measurement using a nuclear imaging technique: Positron Emission Particle tracking (PEPT). The power dissipation due shear stresses is shown to be the dominant mode of dissipation in the tumbling mill with up to two orders of magnitude difference between pressure induced dissipation and shear.

Jan 1, 2014

By A. Shibayama

Soil contamination by organic compounds is one of the most concerned issues on polluted soil. It is well known that there are limited methods to remediate the contaminated soil on site. Especially, the in-situ method for contaminated soil is too difficult to de-contaminate the organic pollutant. In this study, the fundamental ability of soil remediation, which aimed to decrease oil concentration in, in-situ process, have been researched by using a high pressure gas generated from ?crush composition? on artificially oil contaminated soil. The n-hexadecane (n-C16H34) and other organic compounds were selected as soil oil contaminators, gravimetric analysis by soxhlet extraction and GC-MS were used as qualitative and quantitative analysing methods. For the experimental examination, the influences on the difference in the concentration of n-hexadecane (and other organics), the tamping amount, position and repetition of crush composition in soil, and scale (size) of experimental model were investigated. The n-hexadecane concentration reduced by the explosive effect of crush composition showed a reasonable decrease of about 30 wt%~60 wt% compared to the initial n-hexadecane. The removed amount of n-hexadecane and distance from explosion point of the crush composition was related in scale and model of contaminated soil.

Jan 1, 2014