Search Documents

By Julian Glasser

Starting with rutile, containing more than 55% TiO2 and of the proper particle size, the commercial production of titanium tetrachloride via fluidized bed chlorination is relatively very simple and economical. As compared to shaft chlorination, it operates at a much higher capacity for given sizing of equipment, and appears more foolproof, requiring less attention. Operating data were obtained on a 53" diameter fluidized bed chlorinator using Australian rutile and petroleum coke of controlled particle size. Production rates varied from 20 to 50 tons of crude TIC14 per day for a campaign extending over one month. Close to theoretical yields and efficiencies were obtained from the viewpoint of chlorine and/or rutile consumption. Details of important equipment design, critical operating conditions and pertinent results are described.

Jan 1, 1962

By William J. McCloy, Robert L. Gamble

A coal-fired fluidized bed steam generator rated at 12.6 kg/s has demonstrated the industrial and institutional application of fluidized bed combustion by burning high sulfur coal in an environmentally acceptable manner within a populated area. Designed to provide steam for heating and cooling, the unit was placed into service at Georgetown University in Washington, DC, and has already logged 5275 hours.* The unit has consistently operated well within Washington's strict regulations governing emissions of sulfur dioxide (SO2), nitrogen oxides (NOx), and particulates. The Georgetown program, cofunded by the university and the US Department of Energy, has shown that fluidized bed combustion is a promising way to realize the full potential of coal, the nation's most abundant energy resource. In a fluidized bed steam generator, a layer of granular limestone is placed on top of a grid designed to prevent particles from falling through. Air is passed upward through the bed with sufficient force to lift and float the particles. At this point the bed material resembles a boiling liquid. Crushed coal is then introduced into the bed and ignited. When high sulfur coal is burned, limestone absorbs the SO2 produced. The operating temperature of a fluidized bed steam generator is relatively low (approximately 871°C). As a result, NO, formation is minimal. Another potential problem encountered in burning coal is fly ash, a form of particulate. A feature of the fluidized bed design, developed by Foster Wheeler Energy Corp., is a fly ash reinjection system. Fly ash is reintroduced into the bed where it is burned again, thereby enhancing fuel efficiency. Nearly all remaining fly ash is captured by a baghouse dust collector. At Georgetown, the fluidized bed steam generator and all auxiliary equipment are enclosed in a structure aesthetically compatible with the surrounding university complex. The steam generator has two separate beds that can be fired independently, and operation to date has been with one and two beds in service, based on steam load demand. During several operating periods, when the fluidized bed unit was the only boiler in service, it supplied all the steam required by the 18.5 hm2 of buildings on campus. Initially fired with low sulfur coal, the unit was quickly switched over to higher sulfur fuel which will be used most of the time.

Jan 3, 1981

By M. Dubrovsky, J. W. Evans

A laboratory scale cell (approximately 50 amps current) equipped with a fluidized bed cathode was used in a study of the electrodeposition of cobalt from acidified aqueous sulfate solutions The effect of current density (in the range 0.1 to 1 amp/cm2 of diaphragm), cobalt concentration (4 8 to 100 glliter) and catholyte pH (1 35 to 6 2) on current efficiency and energy consumption were determined. Generally the current efficiency increased with increasing current density and cobalt concentration Current efficiencies were comparable to those reported in the literature for conventional electrowinning

Jan 1, 1981

By A. D. Engelbrecht

An investigation was undertaken to ascertain the suitability of four selected low grade, South African coals for gasification in a bubbling fluidized bed for production of synthesis gas and for the development of integrated gasification combined cycles (IGCC). This study consisted of the characterization of the coals, laboratory evaluation of intrinsic reactivity, and experimentation with a pilot-plant fluidized bed gasifier. Results of the characterization experiments show that the selected coals are high in ash, rich in inertinites, very dense (low porosity), with low caking indices and high ash fusion temperatures. Reactivity measurements with a thermogravimetric analyser (TGA), under reaction rate controlling conditions with carbon dioxide, showed that the reactivity of the coal chars decreases with increase in rank of the coal, as expressed by the vitrinite random reflectance and carbon content of the parent coals. The fixed carbon conversion achieved in the fluidized bed gasifier also correlates well with the rank parameter of the coal, with higher conversions being obtained with the lower rank coals. Thermal shattering and attrition of the coal particles produce significant amounts of fines, which correlate with the grindability indices, and no agglomeration (non-caking) was observed. It is concluded that fluidized bed gasifiers are able to utilize typical low grade, high ash South African coals for synthesis gas production and for inclusion in integrated gasification combined cycles for power generation.

Jan 1, 2010

By E. Eccleston, E. Gardner, F. Letarte, R. Schonewille

"In 2005, after nearly a decade of process development and feasibility work, the commercialization of the Falconbridge Nickel Smelting Technology (NST) began in earnest with the design and construction of a grassroots ferronickel plant at Koniambo Nickel in New Caledonia. The NST process was developed as an alternative to the conventional Rotary Kiln-Electric Furnace (RKEF) process for production of ferronickel from saprolitic nickel laterite ores. The NST process promised environmental and energy efficiency advantages over the conventional route. A key step of the NST process involves fluidized bed pre-reduction of calcined laterite ore using direct injection of pulverized coal as the reductant. Two parallel fluidized bed reduction roasters (FBRs) were installed at Koniambo Nickel, each designed for a maximum capacity of 4,200 MTPD of calcined nickel laterite ore. This paper describes the process development and scale-up of the fluidized bed pre-reduction process, the design challenges associated with the prototype commercial units, and the current status of the FBR operation at Konaimbo.INTRODUCTION In the mid-1990s, Falconbridge began to develop a new flowsheet for production of ferronickel from nickel laterite ores. The process that developed came to be known as the Falconbridge Nickel Smelting Technology (NST). The flowsheet, which is particularly appropriate for saprolitic ores, involves several major unit operations, including: drying in a hammer mill-flash dryer, calcination and preheating in a flash calciner, pre-reduction in a fluidized bed reactor, and smelting in a DC arc furnace to produce the ferronickel product. This paper focuses on the fluidized bed pre-reduction step of the process and provides an overview of the process chemistry, laboratory and pilot plant development work, scale-up and commercialization of the pre-reduction step, and the results obtained in the prototype commercial units."

Jan 1, 2017

By Rex T. Ellington

The fluidized bed is an effective method for investigating retorting phenomena and possibly a commercial means of retorting oil shale. Both were examined by Sinclair Oil Corp. (now part of Atlantic Richfield Co.) in the period 1.965 to 1968. The results of the work show that presence of an oxidizing environment during retorting results in loss of oil yield which indicates that vapor phase oil burns in preference to combustion of coke on spent shale. This has implications for several types of retorts. Correlation of the results of this work with that of other investigators shows that the partial pressure of retorting products in contact with oil shale during retorting has an effect on yield. Consideration of hardware indicates that there are several possibilities for commercial embodiment. As a companion to shaft-type retorts the fluidized bed could have good potential. Realistic assessment of costs suggests that further development may have to await commercialization of another process. The existence of a plant in which to test prototype size would markedly reduce such development costs. Results Preliminary development work with the apparatus was carried out using a fluidized bed of sand, as explained later, with the entire system brought up to temperature and flows stabilized. The shale was injected rapidly in a slug (batch) which had small mass compared to that of the high temperature system to make the reaction approach isothermality with reasonable approximation of instantaneous preheating. Typically, the temperature in the center of the bed dropped from 900°F to 600°F one minute after batch addition. It returned to 750' within three minutes and 900° within seven minutes. Obviously, the bed was quenched but it recovered rapidly. Average bed temperatures of 700' to 1020°F were examined to compare the effect of temperature with published results. Yields In the 700°F range were only 10 to 15%, of Fischer Assay (FA). Above about 950'F, oil yields decreased and gas yields increased. Nitrogen was used first as the fluidizing gas to provide a chemically inert medium. Incept for an insignificant dip at 895"F, Figure 1, oil yield was not affected by retorting temperature in the 800° to 900' range as long as residence time was adequate (16 minutes). At 925°F, the oil yield was some 103% FA. With further increase in temperature, the yield decreased to 86% FA at 1015°F. There is no increase in carbon on spent shale, the lost oil goes to Increased gas make.

Jan 1, 1972

By Rex T. Ellington

The fluidized bed is an effective method for investigating retorting phenomena and possibly a commercial means of retorting oil shale. Both were examined by Sinclair Oil (now part of Atlantic Richfield Co.) in the period 1965-1698. The results of the work show that the presence of an oxidizing environment during retorting results in loss of oil yield which indicates that vapor phase oil burns in preference to combustion of coke on spent shale. Consideration of hardware indicates that there are several possibilities for commercial embodiment. As a companion to shaft-type retorts the fluidized bed could have good potential. Realistic assessment of costs suggests that further development may have to wait commercialization of another process.

Jan 1, 1974

By Urie R. W

Fluidized bed roasting of copper concentrates from Mt. Morgan, Mt. Lyell, Mt. Isa, and Peko was performed in a 3 ft 6 in diameter, slurry fed, pilot plant roaster operated under autogenous conditions to produce calcines with desirable leaching properties. A 12 in. diameter, externally heated roaster, provided with a dry feed system, was also used.An account is given of important factors which influence roaster behaviour and performance, and the effects of operating variables on calcine composition and leaching properties are described. Due to copper ferrite formation, a maximum of approximately 50 per cent of the copper in the calcines may be in the form of CuO before the copper leach efficiency falls significantly below lOO' per cent. Recovery of gold by cyanidation of leach residues was consistently high and independent of roasting conditions.INTRODUCTIONIn traditional practice copper is produced by pyrometallurgical techniques when the ,copper minerals in the ore or concentrate are predominantly sulphides, and by hydrometallurgy when the minerals are oxidized. Copper smelting is most suited to large scale operations, and for many years small to medium size mines with sulphide orebodies have been interested ill; alternative processes.Since hydrometallurgical plants (ie. leaching and electrowinning plants) are essentially unitized, they may be scaled down in output without much loss in efficiency or increase in processing cost, and many proposals have been made for the application of this type of process following roasting of the sulphides to render the copper soluble. However, until the advent of fluidized roasting, it was not possible to control the roasting operations sufficiently precisely to produce calcines consistently of the required leaching characteristics.

Jan 1, 1961

By S. Heukelman

Zinc or, a zinc refinery in South Africa, uses oxygen enrichment of up to 26% O2 in its fluidizing air to increase concentrate-throughput in its fluidized bed roasters. The aim of the study is to determine whether O2 enrichment can be reduced by introducing micro-pelletized concentrate into the feed blend, while maintaining concentrate throughput rates and calcine quality. A laboratory scale fluidized roaster was used to determine the strength and oxidation kinetics of suitable micro-pellets. The strength of the pellets was determined by the extent of attrition during roasting. It was found that micro-pelletization decreases the fines in the feed to the roasters; the ?500 µm fraction decreased from 87% to 10%. The micro-pelletized particles do break down during roasting, which increases the -500 µm fraction to 31%. The general morphologies of the roasted particles are similar to those found by previous workers. Micro-pelletized concentrate particles require more time than non-pelletized concentrate particles to oxidize in the roasting step, although this is less than the mean residence time of the Zincor roasters. Roasting micro-pellets in O2-enriched fluidizing air increased the reaction rate.

Jan 1, 2011

By S. Heukelman

Zincor uses O2 enrichment (up to 26% O2 in the fluidizing air) to increase the processing rate of zinc concentrates in the fluidized bed roasters. The aim of this study is to determine whether O2 enrichment can be reduced by introducing micro-pelletized concentrate into the feed blend, while maintaining current roaster feed rates and calcine quality. It was found that, with a load of 20% micro-pellets introduced into the feed blend, that O2 enrichment could be reduced by 60%. It was determined that entrained particles spend on average between 0.46 hour and 2.44 hour in the roaster, compared to particles remaining between 3.93 hour and 4.00 hour in the bed overflow. This compares well with a radioactive tracer test performed by Spira. The required reaction time for micro-pellets was found to be less than the residence time inside a Zincor roaster. The result achieved indicated that the average particle residence time inside the roaster was increased successfully in order to compensate for the longer reaction time required to roast micro-pellets at lower levels of O2 in the fluidizing air.

Jan 1, 2011

By K. Adham, C. Lee

The demand for nickel is continuing to exceed inventories, and producers are working vigorously to increase capacity. Many nickel processes utilize the fluidized bed technology for its fast heat and mass transfer, excellent temperature control and low maintenance. The following four nickel applications of the fluidized bed technology have been commercialized: I) Sulfide ore roasting; II) Nickel sulfide (matte) roasting; III) Nickel oxide reduction; IV) Nickel chloride pyrohydrolysis. This paper examines the issues surrounding the application of fluidization technology to the above processes, from the stand point of the engineer modeling the process and designing the key equipment, based on the historical success stories and the fundamental principles of flow sheet synthesis. Using the available data in open literature, typical flow diagrams (with convenient bases of 1 t/h feed or product) are developed to illustrate the relative flow rates and to highlight the key features of each application. In addition, some historical background information is provided for each process with supplemental notes with regards to our company's involvements.

Jan 1, 2005

By J. Güntner

A significant portion of Outotec's business relates to the application of fluidized bed for processing a wide range of industrial materials, including gold ore and gold concentrate. As part of the former Lurgi and Boliden organization, our division constructed the first industrial reactor for roasting sulphur-bearing materials in 1950, based on the principles of fluidized bed technology. This process, when combined with efficient heat recovery and off-gas treatment and its conversion to sulphuric acid, became the standard for processing sulphur-bearing ores. In the last 60 years we have delivered more than 265 plants and developed (in addition to the standard fluidized bed solution) variants of the fluidization technology, such as the circulating fluidized bed and the bubbling fluidized bed. This paper describes the different options of the fluidized bed technology for gold roasting reflecting on main process design criteria.

Jan 1, 2011

By A. Poll, J. E. Stantan, L. J. Jolley

THE basic problem in the generation of water gas from carbonaceous fuels and steam is the supply of the heat of reaction, and in general the source of this heat is the combustion of a further quantity of carbon with oxygen. Existing and proposed processes for complete gasification differ in the methods employed for transferring this heat to the fuel, and involve one or other of the following alternatives: 1. Use of a steam-oxygen mixture as the gasifying medium, so that the combustion and gasification reactions are combined. 2. Alternate passage of air and steam through a fixed bed, as in conventional water-gas production. 3. Cyclic passage of fluidized fuel through combustion and gasification zones. 4. Intense preheating of steam and of a portion of the gas made, and recirculation of this mixture through the fuel bed. 5. Supply of heat to the fuel bed through an externally heated wall. Except for the conventional water-gas process using large coke or low- volatile coal, only processes in the first group, operating with steam and oxygen, have proved practicable with fuels other than brown coals and lignites. A possible exception, which has not so far reached a commercial scale, is the moving-burden process developed by Imperial Chemical Indus- tries, Ltd. The cost of industrial oxygen is so high that its use can probably be justified only if it is attended by substantial savings in other directions; for instance, the use of cheap fuel. In the United Kingdom, no very cheap solid fuels are available, and it is unlikely that an oxygen-gasification process could compete economically with conventional production of blue water gas from coke. Hence particular interest attaches to all possibilities of making water gas without using oxygen, if any possible saving in fuel or other costs is involved. The cheapest and most abundant coals in the United Kingdom are the low-rank noncaking bituminous coals in small and ungraded sizes, typically those from the East Midlands coal field, and-fines of high ash content produced in coal-cleaning operations. A process capable of gasifying

Jan 1, 1953

By R. J. Dippenaar, J. C. van den Berg

This paper describes an investigation into the prereduction of hematite fines in a fluidized-bed reactor as a means by which they can be prepared for direct smelting in a transfered-arc plasma furnace. A single-stage fixed fluidized bed reactor using the in situ gasification of coal was employed. It is shown that the hematite is reduced to magnetite at 1000 QC, the degree of reduction being limited by the inherent shortcomings of a single-stage reactor in which both the gasification and the reduction reactions have to occur. Methods by which the degree of reduction can be increased are suggested. The gasification process was studied in some detail, and three different reducing agents are compared. The dominating effect of the Boudouard reaction on the behaviour of the fluidized bed is clearly illustrated. Non-coking coals of high reactivity are best suited to this process, a finding that would complement the trend away from coke as a metallurgical reducing agent.

Jan 1, 1989

By A. A. Jonke

The combustion of fossil fuels in a fluidized bed of calcined limestone particles is a potentially efficient and economically attractive process for the generation of steam for electric power production and other uses. The process results in greatly reduced emissions of both sulfur oxide and nitrogen oxide pollutants. Development work, evaluations and design studies are being carried out by various organizations under contract with the U. S. Environmental Protection Agency and the Dept. of Interior (Office of Coal Research). The AEC's Argonne National Laboratory is one of the principal participants in the development program under interagency agreements with EPA and OCR. This paper covers the principal reasons for developing fluidized-bed combustion, its advantages and disadvantages over conventional combustion methods, and some of the potential applications of the process. The participants in the multi-organizational program, the sponsoring agencies, the general status of development of the overall project, and the chief program areas that still require resolution are discussed. The main features of the program of work at Argonne National Laboratory and the results achieved so far are also included.

Jan 1, 1974

By A. A. Janke, G. J. Vogel, W. M. Swift

The combustion of fossil fuels in a fluidized bed of calcined limestone particles is a potentially efficient and economically attractive process for the generation of steam for electric power production and other uses. The process results in greatly reduced emissions of both sulfur oxide and nitrogen oxide pollutants. Development work, evaluations, and design studies are being carried out by various organizations under contract with the Department of Interior (Office of Coal Research, OCR) and with the U.S. Environmental Protection Agency, (EPA). The Atomic Energy Commission's Argonne National Laboratory is one of the principal participants in the development program under interagency agreements with EPA and OCR. The principal reasons for developing fluidized-bed combustion, its advantages and disadvantages over conventional combustion methods, and some of the potential applications of the process are covered in this paper. The participants in the multiorganizational program, the sponsoring agencies, the general status of development of the overall project, and the chief program areas that still require resolution are discussed. The main features of the program of work at Argonne National Laboratory and the results achieved so far are also included.

Jan 1, 1976

By P. J. Adams

Environmental regulations require means for controlling emissions of SO2 NOx and particulate when burning coal. The combustion of coal in limestone fluidized beds is one of the most promising techniques for the necessary reduction in emissions. Fluidized-bed firing, furthermore, offers potential economies in capital equipment. The world's largest steam generator applying fluidized-bed techniques was built under the sponsorship of ERDA and installed in Rivesville, West Virginia. This paper describes the design and discusses the start-up and development difficulties which were experienced during the period from initial operation to current readiness for commercial operation. Other developments leading to utility and industrial fluidized-bed steam generating equipment are reviewed. The future potential of this promising technique is discussed.

Jan 1, 1979

By F. J. Plaul

The dominating technologies for steelmaking are the basic oxygen furnace (BOF or LD process, Linz-Donawitz) and the electric-arc furnace (EAF). The main iron input materials for both are liquid iron as hot metal, or solid iron as pig iron, DRI (direct reduced iron), HBI (hot briquetted iron) and scrap. Hot metal, pig iron (i.e., solidified hot metal) and DRI/HBI are virgin iron materials, which have to be produced from iron ore by so-called ironmaking technologies. The family of ironmaking technologies includes three process routes: blast furnace, smelting reduction and direct reduction. Driven by steadily increasing costs of raw materials in the last two decades, the sector has seen a number of new developments in ironmaking technologies, developments based on fluidized-bed technology. The main advantage of a fluidized-bed technology is that fine iron ore can be directly charged to the process without prior treatment; it does away with agglomeration and its concomitant cost, a step practised in blast-furnace, COREX® and MIDREX® processes. With Posco of South Korea, Siemens VAI Metals Technologies has successfully developed the FINEX® process, a smelting reduction based on the direct use of iron ore fines to produce hot metal. The key technology is the four-stage, bubbling fluidized-bed-reactor system, in which fine iron ore is reduced to DRI fines in a countercurrent flow with a reducing gas generated by coal gasification. Beside surveying the current state of the art, this paper discusses the technological principles of smelting-reduction and direct-reduction processes. The status of FINEX® and the outlook for further developments are described. Crucial to the successful development of the new ironmaking technologies for the direct use of fine ore was the scaling up of the fluidized-bed reactor system, which demonstrated new design features.

Jan 1, 2009

By Enif Gutiérrez Guerrero

Inclusion deposition is still a standing problem in the continuous casting of steel since the deposition of alumina inclusions inside the SEN affects the productivity and the product quality. The present work studies the factors involved in the inclusion deposition at the nozzle and the effects of inertial, gravitational, buoyant, pressure gradient, and Saffman forces on the inclusion trajectories. The results show that the inclusions reaching the nozzle, only 30% get deposited along its walls mainly at the Upper Tundish Nozzle (UTN). This area of higher deposition is identified close to a low static pressure and a high turbulent kinetic energy dissipation zones where the effects of the gravitational and buoyant forces do not promote a significant inclusion radial movement since these are aligned with the direction of the flow stream lines. In contrast, in this zone, the Saffman force shows an important effect on the deposited inclusions, slowing down the inclusions in the vertical axis and increasing their radial movement.

Aug 17, 2017

By Gligorije Stankovic

This paper describes the fluo-solids roaster and acid plants at the new 40,000-TPY Trepca electrolytic zinc plant. The electrolytic zinc plant units were constructed to the design of Singmaster and Breyer, New York and began operation in mid-1967. The fluo-solids roaster plant, constructed according to the design of Dorr-Oliver, Paris, includes concentrate handling and storage facilities; two independent concentrate roasting circuits, each with a 110 to 155 TPD fluo-solids roaster; waste heat boilers; cyclones; electrostatic precipitators; calcine coolers; and calcine conveyors. The acid plant uses the "Petersen system" contact process. The plant has one acid circuit with a capacity of 230 tons of monohydrate per day. Gases for the acid plant are obtained from roasting zinc concentrates. When the roaster plant is operating at maximum capacity, excess SO2 is used in two other Petersen System circuits in the near vicinity.

Jan 1, 1970