Search Documents

By Malsuzaki. Kenji

A mathematical simulation model of the Imperial Smelting Furnace operation has been developed for purpose of improving the furnace operation. The model consists of top, shaft and bottom regions. Analysis in the shaft region is based on differential heat and materials balances taking account of reaction kinetics and heat transfer rates, and those in the top and the bottom regions are based on heat and materials balances under a steady-state condition. Longitudinal distributions of process variables such as temperatures of gas, sinter and coke, gas composition and fractional conversion under a practical operating condition were calculated. With this model, the furnace performance under various operating conditions also can be shown reasonably predicted.

Jan 1, 2003

By H. Y. Sohn, S. PalDey

"Fine particles of nickel aluminides and Ni4Mo were synthesized by reducing mixtures of, respectively, A1Cl3 + NiC12 and NiC12 + MoC12 vapors with hydrogen. Though thermodynamically favorable, the coreduction of NiC12 and A1Cl3 by H2 to form Ni3Al did not readily happen experimentally. The addition of a small amount of aluminum vapor was needed to initiate the coreduction reaction. The product particles as observed by TEM were very fine but usually agglomerated. The electron diffraction pattern of particles identified NiAl and NiA13 along with Ni3Al and metallic Ni. The content of Ni3Al was maximized at 52 mol% at 1050°C under the partial pressures ofH2, A1Cl3, and NiC12 at 57, 1.4, and 0.5 kPa, respectively. When a mixture of NiC12 + MoC15 was reduced by hydrogen, Ni4Mo particles with some Ni or Mo particles were obtained, the maximum content of Ni4Mo obtained being 93 mol % . The particle size was in the range of 100 to 200 nm. An Ni4Mo coating of 700 nm thickness on an Ni substrate was also prepared.IntroductionThe search for new high-temperature structural materials has stimulated much research on intermetallic compounds. Nickel aluminides have low densities, relatively high melting points, and good high-temperature strength properties. They show an increase, rather than a decrease, in yield strength with increasing temperature (1). Ni4Mo is also of interest as a high-temperature structural material. The major shortcomings of these intermetallics are their inherent brittleness at room temperature when they are in polycrystalline form. For much the same reason, the conventional casting of intermetallics is difficult. Ingot metallurgy and powder metallurgy are two other processing techniques. The first technique is quite energy consuming. In powder metallurgy, the powders of metals and alloys are consolidated in near net shape and then subjected to secondary processing. It would, therefore, be advantageous if intermetallic compounds can be produced in fine powder form from inexpensive raw materials, using less energy."

Jan 1, 1998

By Christoph Beckermann, Kai Liu, Richard A. Hardin

"A two-dimensional heat transfer model for transient simulation and control of a continuous steel slab caster is described. Slab thermal and solidification conditions are computed by the model as a function of time-varying casting speed, secondary spray cooling water flow rates and temperature, slab thickness, steel chemistry, and pouring and ambient temperatures. A solidification model that includes the effects of steel chemistry, cooling rate and mierosegregation on the solidification path is incorporated directly into the caster model. Comparisons between measured and predicted liquidus and solidus temperatures are given for two low alloy steels, and show good agreement. Predicted and measured slab surface temperatures recorded on an operating caster are compared with this transient model and show that the model can predict the temperature response at the slab surface. Results of several simulations are given to demonstrate the effects of changing casting conditions on the slab thermal profile and the solidification end-point. A control methodology suitable for online control of a continuous casting machine is described, and its ability to control the surface temperature profile by dynamically adjusting secondary spray cooling flow rates is demonstrated using the simulator. IntroductionIn order to remain competitive in today's world-wide market for continuously cast steel products, steel producers are finding that it is ever more important to implement process control and to develop a more thorough technological understanding of their casting process. By integrating process control and monitoring into both production and quality control, producers are better able to meet customers' demands for steel of the required quality, quantity, size, grade, and properties at the lowest cost. Computer models used for real-time/on-line prediction and control of continuous steel casters are fundamental tools to accomplish this. Accurate on-line prediction and control of steel solidification and heat transfer allows for more flexibility in caster operation by giving operators the ability to change casting speeds while keeping critical process parameters within required ranges. Such control 'capability also results in more uniform quality throughout an entire casting sequence from startup to shutdown. Furthermore, due to the unreliability of temperature sensors, and the lack of good sensors for important process parameters such as solidification end-point and liquid pool depth, computer-based control models are often the only available option."

Jan 1, 2000

By Yun Li

An innovative lead recycling process from scrap lead-acid battery paste is presented. The novelty in the process is avoiding SO2 generation and emission by using reductive sulfur-fixing technique. Iron-bearing secondary wastes produced from metallurgical industry were utilized as sulfur-fixing agent to capture sulfur in the form of FeS (s) instead of generation of SO2 (g). Na2CO3 molten salt was added to the smelting system to speed the reactions and improve valuable metals’ recovery and sulfur-fixation efficiency. Furthermore, this process can simultaneously co-treat various lead and iron-bearing wastes. At the same time, some precious metals, such as Au and Ag, contained in iron-bearing wastes can be recovered. The feasibility and reliability of this process was investigated thermodynamically and experimentally with the help of HSC 9.0 database and XRD and SEM-EDS analysis. A possible reaction mechanism and path in PbSO4–Fe2O3–Na2CO3–C smelting system was also clarified.

By I. Gaballah

Decontamination of synthetic solutions of PbC12 containing 10, 100 and 1000 ppm of lead, using chemically treated barks had been studied. The percentage of !cad cations' removal from solutions depends upon the pH and the initial concentration. About 99 % of the initial lead content can be removed at pH of about 3.5, 5.5 and 6.5 for initial concentrations of 10, 100 and 1000 ppm respectively. The maximum retention capacity of the treated bark is about 83 mg of lead per gram of modified bark. Bark loaded with lead had been analyzed by Infra Red spectroscopy. It seems that lead reacts with hydroxyl groups of the phenolic constituents of the bark. On the other hand, the removal of a lead cation by the bark leads to the release of two H+. This seems to show that the removal of lead could be interpreted as an ion exchange with hydrogen belonging to the hydroxyl groups of the modified bark.

Jan 1, 1994

By Tuomas Hirsi

The world’s first large scale modular solvent extraction plants have been delivered by Outotec. The first of these is now in operation and has proven that the VSF®X technology can deliver the excellent performance of the Outotec VSF® solvent extraction process. Modular delivery allows site work to be minimized and the manufacturing done in a controlled environment, allowing for serial production manufacturing benefits. Container based delivery was found to be a highly efficient way of utilizing the standardized transportation methods on a global scale. Site work with modular units was found to be efficient and highly predictable. In this paper, we present the first successful Outotec VSF®X deliveries and discuss the benefits of the modular delivery and design compared to the standard solvent extraction installation’s delivery. The process performance of the VSF®X is also discussed with experiences from the first industrial reference presented.

By André Laplante

The mineralogy of the Joe Mann mine differs from that of other deposits of the Chibougamau area that are exploited by Les Mines Camchib Inc.. It is characterized by very fine first generation gold and very coarse second generation electrurn. Successful milling required adjustments of the processing flowsheet, which includes gravity, flotation, and cyanidation. A study of coarse gold liberation in the gravity/grinding circuit is described. Modifications to the flotation circuit and the reconditioning of a small capacity cyanidation circuit are presented. As a result of the circuit modifications, gold recovery increased from 65 to 81% in flotation and cyanidation. Overall gold recovery increased from 77% to 88-89%. These improvements are mostly attibutable to the recovery of -10 urn gold, whose presence in the Joe Mann ore and original circuit tails had been identified by process mineralogy.

Jan 1, 1989

By R. H. Hanewald

The INMETCO process has been modified so as to recover nickel. chromium and Iron from a wide variety of metal containing waste-streams. This now includes the recovery of metals from spent acid solutions such as chromic acid etching I1quids. nJcke1 and chromium plating solutions; stainless and superalloy pickling solutions. etc. In addition. hazardous electric furnace stainless steel and. superalloy baghouse bags can be processed so as to recover the valuable metall1cs. A detailed review of the above new recovery techniques w1ll be discussed as well as the current operating methods used at INMETCO.

Jan 1, 1992

By Zhen Zhang, Jiang Diao, Tao Zhang, Yi Ren, Lu Jiang, Xiao-Man Yan, Bing Xie

The precipitation behavior of phosphorus enrichment phase was investigated by slag modification with Al2O3. The mineral phase of the original slag and modified slags were measured by mineral phase microscope, SEM+EDS and XRD. The mechanism of Al2O3 modification was discussed according to the thermodynamic theory analysis software (Factsage version 6.3). The results show that the high phosphorus solid solution (nˊ2CaO·SiO2-3CaO·P2O5) was generated by the continuous reaction of nC2S-C3P (nˊ＜n) solid solution and Al2O3 under 1350℃. The amount of initially precipitated solid solution (nC2S-C3P) was reduced and even disappeared with the increasing of Al2O3. If the addition of Al2O3 is enough in the slag, the high phosphorus solid solution (nˊC2S-C3P) that generated by the above mentioned reaction will continue to react with Al2O3 to produce Ca2Al2SiO7 and even C3P, which was demonstrated that the addition of Al2O3 has a positive influence on the precipitation of phosphorus enrichment phase.

Jan 1, 2015

By Ronald Erdmann

Today the BOF filter dusts and sludges are mainly dumped due to their zinc contents. By typically ranging from 2 to 5 % they prevent the filter dusts and sludges from beeing recycled via the blast furnace route. Based on the different discharge kinetics of Iron and zinc during the main blowing period In a bottom stirred BOF a simple and efficient system for recovery allow zinc fractions has been developed. The obtained material Is suitable for recycling without nsc of shell formation In the blast furnace. Different subsequent development steps have been performed. By starling with a very simple lime dependent model the sludge from the BOF off gas cleaning system was collected in two different sludge channel systems. This model based an the fact that most of the scrap based zinc Is discharged from the melt within the first eight to ten minutes of the BOF process. To Improve the system a spectroscope zinc sensor was Installed at the hot section of the off gas cleaning system to get more reliable informations on the actual zinc concentation of the BOF dust. By use of the system up to 50 % of the BOF sludge can be recycled.

Jan 1, 1995

By W. G. Davenport

Flash smelting is used. mainly for making molten Cu-rich matte* from fine Cu-Fe-S** flotation concentrates. It blows dried concentrate particles into a hot fumace, surrounds them with 01-rich gas and allows them to react. The results are: (a) partial oxidation of Fe and S from the concentrate (b) generation of heat (c) melting of the oxidized particles to form molten Cu-rich matte, ~65% Cu and Cu-barren slag, ~1 % Cu. The melted particles fall to the hearth of the flash furnace where they fonn matte and slag layers, The matte is tapped from the furnace and oxidation-converted to metallic copper. The slag is skimmed, treated for Cu recovery then stockpiled or sold. Figures 1.1 and 1.2 show industrial flash furnaces and the position of flash smelting in the coppermaking flowsheet. ,Fig. 1.3 shows the locations of flash furnaces around the world.

Jan 1, 2001

By Jose R. Parga

In mining operations, cyanidation is the ,predominant method by which gold and silver are recovered from their ores and it is recognized that cyanide consumption can be a major factor that contributes to the operating costs for such operations. Also after extraction and recovery of precious metals a certain amount of cyanide is delivered to the tailings pond and must be considered with respect is environmental problems due to the toxicity of cyanides. In this regard, the Air-Sparged Hydrocyclone (ASH) has been used as a reactor for the treatment of cyanide solutions in two ways; first for cyanide recovery by acidulation using the Mexican modification of the Mills-Crowe process and second for cyanide destruction by oxidation with the use of chlorine dioxide (ClO2). In both cases, excellent performance can be achieved using the high capacity ASH system.

Jan 1, 1998

By Nicholas E. Vanderborgh

Projections show that domestic coal will serve for the majority of energy supplies during the next decades. Thorough chemical cleaning of this coal can be accomplished in long-residence time, slurry-transport systems to produce high-quality fuel product. Concurrently, mineral recovery from coals will supplement existing ores. This paper describes this concept and gives preliminary engineering considerations for mineral recovery during transport operations.

Jan 1, 1982

By Jilai Xue, Jun Zhu, Yongqiang Liu

"Up-grading silicon feedstock by removing B and metal impurities can improve process efficiency and lower production cost in metallurgical processing for solar cells production. Hydrometallurgical study has been carried out in laboratory through alternative treatments of the metallurgical grade (MG) silicon (-200 mesh) by using hydrogen peroxide, hydrofluoric acid (4 mol/L) and NH4Cl-NH4 F (30:5) solution. The experiments were usually performed under mechanical agitation at 70 ? for 5 h. ICP-AES analysis showed that B content in MG silicon after the hydrometallurgical treatment has reduced by 92.4 %, and Fe, Al, and Ca contents by 98.8 %, 98.0 % and 81 %, respectively. Kinetics of these processes was also studied for better understanding of the effects of silicon powder size, acid concentration, leaching and oxidizing time on the processing chemistry.IntroductionAs one of the most clean and promising new energy, solar energy is used more and more in many countries all over the world, especially in United States, Japan and European Union. Most of industrialized states have made their national photovoltaic plans, which have stimulated further increase in use of solar energy. Photovoltaic Industry is at a high growth rate about 30 % [1-2]. For silicon solar cells to remain the mainstay for the photovoltaic industry it is necessary to develop a low-cost solar grade silicon feedstock [3]. At the same time, the availability of the currently M-G silicon from the semiconductor industries becomes limited [4]. With the advantages of low cost and low energy consumption, metallurgical routes to product solar–grade silicon get more attention [5]. These routes mainly include pickling, slagging, vacuum processing and directional solidification, etc [6]. Among them the most important processing step is the directional solidification, but it still can not satisfy the industrial demand for removing B. Removing B from Si remains as one of the most difficult and important processes in making M-G silicon [7]."

Jan 1, 2012

By Kenneth L. Nash

The control of solubility of waste actinide ions, by conversion to highly insoluble mineral phases has been demonstrated in the laboratory. Actinide metal ions are removed from neutral pH solutions by a combined ion exchange-decomposition-mineralization process based on the application of the naturally-occurring hydrolytically unstable.polyphosphate organic compound phytic acid.

Jan 1, 1999

By Jussi Vaamol

A commercial CFD-code was used to solve isothermal flow fields of gas and liquid in a Peirce-Smith converter. The model was validated with a 1/4 scale water model, and parametric study. Limits of the modeling technique used were recognized, but calculated results indicate that the present model predicts the general flow field with reasonable accuracy. The model was used to examine general flow conditions in an industrial scale PS-converter. Typical scaling factors of physical models were also evaluated with the aid of predicted bubble distribution, patterns of the flow fields and magnitude of flow velocities. The numerical simulations were found to open new viewpoints to the fluid dynamic related phenomena in the PS-process.

Jan 1, 1998

By Zhang Yongzhu

In hydrometallurgical processes of PGMs separation and refining, differences between 1-PGMs (Ru;Rh;Pd) and h-PGMs(Os;Ir;Pt) in thermodynamics and kinetics have been observed. The successful practice in the separation and refining of PGMs in China, is mainly based on the following two kinetically extraction sequences of: (1) for the extraction of PGMs complexes in different configurations with coordination mechanism (AuCI,) -> (MCl6)2-> (MCl4 )2-> (MCI6) 3- , and the substitution rate for h-PGMs complexes with higher effective nuclear charge Z' is much more slow than that of I-PGMs. and (2) for the extraction of PGMs in different configurations with oxonium (or ion -exchange) mechanism (AuCl4)-> (MCl4)2--> (MCl6)2-> (MCl6)3- and the extraction of h-PGMs complexes with low surface charge density is more fast than that of I-PGMs complexes. In view of atomic structure theory, the similarity of atomic radii and chemical properties and difficult separation of PGMs resulted from the Lanthanide Contruction between 5th period (1-PGMs) and 6th period (h-PGMs). The differences between h-PGMs and 1-PGMs are due to the loss shielding of 4f subshells on 5d electrons for h-PGMs with higher nuclear number, which makes h-PGMs have a higher Z' (effective nuclear charge) and strong attraction for outer space electrons. As a result, h-PGMs metals and complexes are thermodynamically more stable and kinetically more inert than the corresponding 1-PGMs. The differences between h-PGMs and 1 -PGMs in aspects of elements properties, complexes, hydration, substitution and redox reactions , are discussed.

Jan 1, 1993

By C. E. M. Meskers, U. Boin

"The increasing use of coated magnesium in consumer products results in creation of coated Mg scrap during product manufacture and after End-of-Life product treatment. Currently this material is generally not recycled, leaving a material resource unused. Closure of the magnesium cycle in a sustainable manner is necessary. In order to do so, the effect of coatings on the recycling process has to be quantified, predicted and minimized. For this purpose metrics have been developed, based on first principles supported by detailed understanding of the recycling process. The developed 3D metric enables quantitative assessment of the recyclability and links coating design, product design and recycling to each other in a visual manner. The parameters that form the metric can be measured and predicted, hence an engineering basis for Design for Sustainability of coated magnesium is provided.IntroductionEvery product progresses through the four phases of the product life cycle depicted by figure 1. In each phase residues are created. Their amount and composition is largely determined by the complex material combinations created/invented during product design in the manufacture phase. Compared to the ideal cycle the magnesium cycle is far from closed (fig. 2). Most noticeable is absence of the link between the EoL phase and raw materials production. A closed cycle only exists for class 1 scrap, which goes from the product manufacture phase directly to production from industrial material and returns to the manufacture phase as magnesium alloys. The four problematic streams are marked by ???. Coated semi-products are present in two of the four residues, namely in rejects and collected scrap. When these semi-products are recycled the amount and composition of the dross and salt slag residue is affected as well.During product design selection of the coating takes place, fixing the coating character¬istics and properties from this moment on for the rest of its life cycle. The choices made in the manufacturing phase are therefore critically linked to the recyclability of coated semi-products as well as the sustainability of the magnesium cycle as a whole. Sustainable closed life cycles, in which the quality of materials is preserved and residue creation and resource depletion are minimized, can be attained by selecting the appropriate alternative during product design. To realize this the effect of design choices on the life cycle and more specific the recycling process has to be known and quantified."

Jan 1, 2008

By Isabela Leao Amaral da Silva, Felipe Perisse Duarte Lopes, Alice Barreto Bevitori, Sergio Neves Monteiro

"Jute fibers have in the past decades being investigated as possible reinforcement of polymer composites. However, information is still needed on the fiber interaction with a polymeric matrix for a complete evaluation of the capacity of load transference inside the composite. The present work investigated the interaction of jute fibers with polyester matrix by means of the critical length assessment through pullout tests. Tensile tests of polyester sockets embedded with different fiber lengths allowed the critical length to be determined and then the interface shear stress to be calculated. A relatively low interfacial strength was found, which indicates a weak adhesion between the ramie fiber and the polyester matrix. The SEM analysis of pulled out fibers corroborates this result.Introduction Natural fiber, mainly those lignocellulosic extracted from plants, have, in the past few decades, attracted the attention not only of scientists but also of industrial technologists of our society interested in their engineering applications. As it is well known, uses of natural fiber in clothes carpets, baskets, ropes and low cost construction roofing has existed from the beginning of our civilization. Today environmental and energy saving issues are motivating research works on new uses of lignocellulosic fibers in polymer composites [1-6]. Moreover, industrial application of lignocellulosic fiber composites are already in technological sectors such the automobile industry, packing and civil construction [7-9].In addition to environmental, economical and social benefits, some lignocellulosic fibers present specific properties that are comparable to those of other synthetic fiber used for polymer composite reinforcement. For instance, the specific strength (GPa.cm3/g) of curaua (1.31), sisal (0.92) and ramie (0.93) fibers, from results obtained with very thin diameters [10] are relatively closer to that of glass fiber E (1.33). Therefore, in principle, it would be technically justified to replace glass fiber, which is more expensive, toxic and represents a problem to the environment [ll], by a strong lignocellulosic fiber. However, serious drawbacks such non-uniform dimensions and heterogeneous properties [6] as well as the tendency to form aggregates during processing and incompatibility with a hydrophobic polymer matrix, reduce the potential of lignocellulosic fiber to be used as composite reinforcement [1-6]. In particular, a low interfacial strength causes a weak adhesion between the hydrophilic fiber and the polymer matrix."

Jan 1, 2011

By Francis Vanbellen

Umicore Precious Metals Refining operates an integrated precious metals smelting and refining plant in Hoboken, Belgium. Once a smelter and refiner of complex concentrates, the plant today?s feed consists exclusively of industrial and consumer recycled products, making it the world?s largest recycling facility for precious metals. Unlike the fairy tale of the Frog Prince, it took much more than a princess? kiss to successfully realize this makeover. A completely renewed plant has been built over the past decade. The most visible technological innovation was the commissioning of the Pb-Cu smelter. Its flexibility towards very different types of feed makes it perfectly suited as main entry to the Hoboken flow sheet. A new Cu-leaching & electro winning plant and precious metals refinery make up the Precious Metals Operations (PMO) whose targets are fast throughput and maximized yields for gold, silver and the platinum group metals. The Base Metals Operations (BMO), flexibly process the by-products from the PMO, valorizing ?impurities? like indium, tellurium, selenium and others. Off gas and waste water treatments ensure compliance with strict environmental standards. Precious metals recycling is an art that goes beyond mastering a unique flow sheet. Umicore Precious Metals Refining offers a complete recycling service, taking care of sampling and assaying, metals management and logistics. The quality of this integral service is recognized through the attribution of ISO certifications for our operational activities, sampling and the environmental care. And it?s an art that follows Michelangelo?s experience: ?Art is 5% of inspiration and 95% of transpiration.?

Jan 1, 2006