Search Documents

By Wenshan Zhang

The industrial production experiments on Zn, Mn simultaneous leaching, impurity removal and ZnMnO2 simultaneous electrolysis were carried out. The process flow, technical requirement and research results about the experiments were discussed and the good technical quail-fixation and high quality of products were obtained. Reactions for each major technological process have been expatiated based on the thermodynamic analysis.

Jan 1, 2006

By Bora Derin

Optimization of slag composition has great importance on effective and clean metal production technologies. Reddy-Blander (RB) model, a priori, is very useful tool for prediction of impurity capacities of industrial slags. In this study, sulfide capacities (Cs) of 19 lead smelter slags indicated in the literature were calculated and effects of Cs values on sulfur content of lead bullions were discussed.

Jan 1, 2006

By S. Raghavan

The thermodynamic activities of MgO in the solid solutions that can exist in the system NiO-Mg0-Zn0 are determined by measuring the EMF of the cell: O2 (g), Pt / MgO, MgF2 // MgF2 // x MgO + yNiO + (1-x-y)ZnO / Pt, O2 (g) / MgF2 in the temperature range 1190-1237 K. Equilibrium phases were prepared along the quasi- binary lines MgO/NiO = 0.1765,0.3333, 1.0,3.0 and 5.667 with the ZnO contents being 0.1, 0.2, 0.25, 0.35, 0.5, 0.75 and 0.9. The crystal structures of the phases were identified by X-ray diffraction. Results obtained so far show that a single phase MgO-rich cubic solid solution exists upto 0.2 ZnO content and for compositions above 0.25 ZnO, a second ZnO rich wurtzite phase forms in addition. Activity measurements show that for low MgO and ZnO contents, the MgO activities exhibit ideal to slight positive deviation from ideality and at higher MgO contents, a negative deviation is shown. Further studies are in progress.

Jan 1, 1993

By He De-wen

The increasing population and living standard in urban areas, have been accompanied with the growing quantity and composition complexity of rubbish, which are causing well-known social effects of pollution, while rubbish (solid waste) is a recyclable resource. To convert rubbish into useful materials, the essential measure is to carry out sorted collection of rubbish. The preconditions of implementing sorted collection are presented in the paper. 1 Characteristics of rubbish composition and amounts of recyclable contents are basic condition to implement sorted collection. 2 The existing available technologies of recycling, economic benefit from recycling, and disposal scheme of residual rubbish are restrained condition for sorted collection. 3 Public understanding and support to sorted collection are the key to success. 4 The government policies to be favorable for sorted collection is the pledge of success. 5 The establishment of a steady solid waste recycling market is also a guarantee to implement sorted collection continuously. 6 To establish management system of rubbish recycling as soon as possible. Further, the methods and procedure of sorted collection are discussed in detail and beneficial comments and theoretical basis to promote sorted collection of rubbish in urban area are presented; it will contribute reference value to municipal solid waste management.

Jan 1, 2006

By G. St-Amant, V. Cloutier, E. Ghali, S. Jin, G. Houlachi

During the casting of lead-silver anodes, variations in cooling rates result in the formation of an uneven microstructure. The slowly cooled areas (SCA) have a coarser microstructure than that of the remaining part (called "the general zone"). The effect of anode microstructure on the electrochemical behavior was investigated using galvanostatic, potentiodynamic and electrochemical impedance techniques. The results show that the resistances for the two steps of the oxygen evolution reaction on the slowly cooled areas of Pb- Ag anodes are higher than that on the general zone. The double layer capacitance for the first step of the oxygen evolution reaction (OER) and the pseudocapacitance of the second step of OER on SCA are smaller than those on the general zone. The potentiodynamic results show that the amount of lead dioxide formed on the SCA is greater than that of the general zone of the anode. The potential decay curves after 30 minutes of galvanostatic polarization at 45 mA/cm2 show that the corrosion potential of the SCA is 200 mV lower than that of the general zone. This can lead to perforation because of the formation of a galvanic cell with a small anode and a large cathode.

Jan 1, 2000

By Marco A. S. Aguiar, Luis G. S. Sobral, Vânia Mori, Paulo A. Medeiros da Silva

"Copper occurs in the crust of the earth, predominantly, as sulphides. Among the copper sulphide minerals, the chalcopyrite is the most abundant and the most refractory to the conventional oxidative processes. This work aims at developing an electrolytic process for treating a copper sulphides flotation concentrate, more precisely chalcopyrite (CuFeS2) and bornite (Cu5FeS4) in the percentages of 70 and 30%, respectively.This paper presents a low-cost operational electroleaching process for treating copper sulphides flotation concentrates, with a high chalcopyrite content. This research practical work aims at improving the copper extraction from that sulphide mineral, in a relatively short time with low-operating cost taking into consideration the influence of a cationic surfactant. The electrolyte of the electrolytic reaction system was a 2,0 mol.L-1 NaCl solution containing CTAB, a cationic surfactant. The electroleaching system contains one DSATM (dimensionally stable anode) anode and two nickel or copper foams (threedimension electrodes. During the electroleaching process the chloride ions are oxidized to chlorine at the anode surface, which in contact with the aqueous phase generate enough hypochlorite ions to oxidize chalcopyrite.The copper ions released from the chemical oxidation process are reduced at the cathode surface as metallic copper."

Jan 1, 2008

By Jeffrey F. Adams

Gypsum fouling is a common problem in the hydrometallurgical industry. It is a particular problem in free sulphuric acid neutralization, or iron removal operations where sulphates are removed from aqueous solutions by the addition of calcium-containing bases. Previous work revealed a strong correlation between the degree of gypsum supersaturation in the reactor and the rate of scale growth indicating that scale formation and growth are primarily controlled by chemical phenomena. However, the chemical behaviour of gypsum is variable and unpredictable with solution chemistry and temperature. Many of the "rules of thumb" that are used to predict its behaviour (and avoid fouling) are in fact based on gypsum solubility in water, rather than on real mixed metal sulphate systems. However, despite this unconventional solubility behaviour, we have been able to accurately model it in Ni, Mg, and Zn containing solutions over a wide range of temperature (25°C-90°C) and solution concentration (0-6 m) using the OLI simulation software. Furthermore, by studying fouling rates in a simulated continuous neutralization reactor, the relationship between process conditions and fouling rates were explained for the first time. This has led to an understanding of how techniques for minimizing gypsum fouling work.

Jan 1, 2003

By Roald Ysteboe, Finn Olesen

"Elkem has developed a process that utilizes SPL as a raw material for pig iron production. This process will be demonstrated in industrial scale during 2008 and 2009. The process developed produce iron, and the reduction material used, is the carbon present in the SPL. The iron source could be either virgin iron ore or waste/recycled material from the steel industry. The SPLrefractory and bath material is dissolved in the slag produced. The slag is designed so that any leaching of environmentally dangerous elements is minimized. This process can in addition to SPL, consume other types of waste derived from the primary production of aluminium. Elkem intends to supply this demo project with SPL and other waste products from external sources, domestic as well as international ones.IntroductionSpent Pot Lining (SPL) is generated when an electrolytic cell for producing aluminium is taken out of service and the refractory and carbon lining is removed from the steel potshell.The yearly generation of SPL world wide is exceeding 500 000 tonnes. The major amount of this quantity is stockpiled or land filled, unprocessed.SPL contain large amount of water soluble fluorides and some amount of cyanides and is classified as hazardous waste in most countries."

Jan 1, 2008

By Sylvie C. Bouffard

The need for a better understanding of the heap biooxidation pretreatment of pyritic refractory gold ores has prompted us to develop a rigorous mathematical model of the process. The hydrological structure of the model takes the form of lateral stagnant pores in contact with a uniformly distributed gas stream and connected to vertical plug flow channels, as suggested by the results of an independent study of column hydrology. A model of pyrite oxidation kinetics was derived based on electrochemical leaching theory and the results of potentiostatic stirred tank and column tests. The growth rates of attached and planktonic iron- and sulfur-oxidizing cells are modeled with separate Monod expressions over three separate temperature ranges corresponding to mesophiles, moderate thermophiles, and extreme thermophiles. Isothermal column tests validate the model simulations. Excellent fits of several leaching indicators (potential, extent of sulfide oxidation, iron concentration, cell numbers) reveal the rate-limiting step to shift from particle kinetics to oxygen gas/liquid mass transfer with increasing temperatures and pyrite head grades. Competition for oxygen between sulfur- and iron-oxidizing microorganisms lowers potentials and slows down pyrite oxidation. This modeling tool may assist engineers in the design and operation of heaps to give more complete gold liberation in a shorter time.

Jan 1, 2003

By H. Y. Cheng

A pulse column solvent extraction system was evaluated as an alternative to mixer-settlers for the separation and purification of rare earths. The column tested had an inside diameter of 44.5 mm and had 36 sieve plates with a free area of 25%. Pulsing was provided pneumatically using a solenoid valve controlled by a timer so that both pulse amplitude and frequency could be varied. Feed to the column was a mixed rare earth chloride solution containing 10 g RE L-1. The extractant was 5% Ionquest® 801 in Shellsol 2037 diluent. Hydraulic performance of the pulse column was excellent with no propensity towards stable emulsions or crud formation under normal operating conditions. The column was operated in organic-continuous mode with flow rates chosen so that yttrium and the heavy rare earths were extracted with high efficiency while the light rare earths were rejected. Yttrium extraction varied from 83 to 99.2%. Concentration profiles were measured in both the aqueous and organic phases, and, from this data, the height of a transfer unit (HTU), the mass transfer coefficient (Kxa) and the continuous-phase axial dispersion coefficient (Ey) were computed. The HTU ranged from 17-92 an which is within the range of values reported for other (non rare earth) pulse column systems.

Jan 1, 1992

By F. Guevara

The paper presents results of physical and turbulent three-dimensional numerical simulation of the gas flow in the wind box and reaction shaft of the concentrate burner of a flash furnace. Physical simulation work was carried out in a 1:5 linear scale model, where the velocity field was measured using a Pitot tube. The mathematical model consists of the three-dimensional averaged Navier-Stokes equations, turbulent kinetic energy and dissipation of turbulent kinetic energy using the Renormalization Group (RNG) theory for the k-e turbulence model. Computations were performed using FLUENT, based in a finite- volume code. The geometry of the concentrate burner was separated in two sections: wind box and reaction tower. Results obtained at the exit of the wind box were used as boundary conditions for the reaction shaft. The effect of boundary conditions on the numerical results was also studied. Results of physical and numerical simulations show an asymmetry of the velocity field at the exit of wind box. This asymmetry is possibly due to existence of a separated flow in the back of the exit ring. The agreement of physical and numerical results assess the capacity of the turbulence RNG k-e model to reproduce correctly the behaviour of the velocity field at the exit of the concentrate burner.

Jan 1, 1999

By Vladyslav M. Sokolov

The cost effective and environmentally friendly recycling technology was developed and tested. It enables utilization of the fine nickel-base superalloy scrap in a form of heavily oxidized scarfing granulates. The process of granulates generation was discussed in details. Their properties were investigated. The results of literature search showed anticipated sufficient improvement of the properties of cast iron by its alloying with the elements from the scarfing granulates. The novel alloying approach is based on the two stage reduction operation. Firstly thegranulates were partially reduced in a solid state by their exposure with powdery carbon at the range of 1550 ? 1700°C. Then the gotten product was efficiently introduced into liquid iron since it has a form of fine natural agglomerates for arranging the optimal conditions for reduction of the granulates. The thermodynamic evaluation demonstrates higher reduction efficiency of carbon and silicon dissolved in iron than of the same elements in a form of the separate phases. The considered process partially provides itself by energy since the reaction of reduction of the chromium oxide by silicon dissolved in liquid iron has exothermal character. The mostly complete extraction of Ni was received. The sufficient reclamation of Cr was gotten at the same time.

Jan 1, 2006

By Bruce Cavender

Managers are frequently faced with the decision to perform a task or manufacture an object in-house or to hire an outside vendor to perform the function. Outsourcing decisions are usually driven by economics: work is outsourced if it can be completed at a lower cost or in a shorter time than it can in-house. A technique termed incremental analysis can be used to make this decision. Incremental analysis examines the financial impact of outsourcing decisions as a function of the firm's fixed and variable operating costs. To use this tool, individual components of production cost are identified as being either constant or varying with levels of production activity. The assignment of cost type can be made in several ways: though analysis of historical operating data, understanding of individual expense types, and so forth. Changes in fixed and variable costs resulting from each potential course of action are explicitly identified to project the financial outcome of each alternative. The alternative having the greatest positive impact on profit is selected for implementation. By using the fixed- and variable-cost framework, the analysis is conceptually straightforward and substantially simplified. Production managers can therefore use incremental analysis as a tool for fast economically beneficial decisions on a real-time basis.

Jan 1, 1999

By Abhoy Mukherjee

The Luanshya Smelter is a traditional Reverberatory Smelter which once worked with up to three coal-fired reverbs, and now operates one Reverb and one hot Peirce- Smith Converter, projected to produce approximately 42.000 tons per year of copper anodes. The aim of this study is to select a smelting technology which best fits the upgrading of the Smelter, such that low capital and operating costs are achieved for the projected design production capacity of 60.000 tpy, limited by the available supplies of concentrates. An equally important requisite is the compliance of present and future environmental regulations, which determines the need to install and Acid Plant to treat the smelter primary gases. In the process selection study, the following technologies were analyzed, at a Conceptual Engineering level: the Oxy-fuel Burner Reverb, the Teniente Converter, the CONTOP Cyclone Smelting Reactor, and further, the Ausmelt Furnace, the engineering of which was provided by the proprietary firm. The engineering of the other processes was developed by INDEC, which also integrated the comparative analysis of the four options. The analysis of a comprehensive set of technical factors, including integrated smelter metallurgical models, together with the evaluations of economical features, led to the selection of the CONTOP Smelting Technology for the modernization of the Luanshya Smelter.

Jan 1, 1999

By T. I. Arbuzova

The present work presents the original data concerning using a high pressure torsion method and a shock wave loading technique to produce compact oxide nanomaterials and investigations of the effect of severe plastic deformation on a microstructure, crystal lattice and stability of these compounds. This allowed us to compare two ways of deformation action that can be characterized as quasi-static and dynamic effect, correspondingly. Particular attention was paid to a stoichiometry and surface composition changes upon severe plastic deformations. A procedure for studying chemistry of the oxide nanomaterials by means of nuclear microanalysis and Rutherford back scattering has been worked through. For surface studies the X-ray photoelectron spectroscopy has been used. It was shown that both distortion methods permit to produce massive nano-scale oxide materials from the coarse-grained powder during a single technological cycle. Bulk nanocrystalline materials based on LaMnO3, TiOy and ZrO2:Y2O3 were obtained by the quasi-static deformation technique. Nanoscaled ceramics of CuO, Mn3O4 and LaMnO3 were produced by the dynamic deformations. The density of the nanoceramics comes to 99%. Size effects and specific imperfection of the nanoceramics obtained lead to a set of particularities of physical properties.

Jan 1, 2006

By Shoji Taniguchi, Lifeng Zhang

"In this paper, firstly the 3D single-phase turbulent steady fluid flow in a vessel with four baffles stirred by a single impeller is mathematically simulated. Turbulence is modeled by using the standard k - e model. Sliding-grid method is used to model the impeller. The flow domain is divided into two cylindrical, the inner one rotates at the same speed as the impeller, and the outer one is fixed with the baffles. Results indicate that the high-speed zone is near the paddles, and larger stirring speed generates larger fluid flow velocity. The calculated stirring intensity data are used to analyze the experimental results. Secondly the effects, such as filter pore size, gas flow rate and NaCl concentration, on bubble size are studied by experiment. For the particle removal rate by bubble flotation in this vessel, first order kinetics is adopted. The effects of initial number of the particles, gas flow rate, particle and bubble size, stirring speed and surface condition, on the removal rate constant are discussed, and an empirical equation is derived by experimental data. At last, a simple model is developed to study the particle attachment probability on bubble surface under turbulent flow conditions. IntroductionIt is well known that inclusions have a bad effect on steel quality. Trying to remove inclusions from liquid steel as many as possible is one of the main objects for the metallurgical workers. Lots of ways are developed to remove inclusions from liquid steel. Gas injection is an effective one. This technique is used to achieve homogeneity in the temperature and metal composition and to assist in the removal of second phase and dissolved impurities from molten steel. Gas injection is commonly applied to the secondary metallurgy processes and continuous casting, for example the ladle argon gas treatment, RH vacuum degassing, and the gas injection in the Submerged Entry Nozzles (SEN) of continuous casting mold, etc. The development of these processes focuses on achieving two conditions: fine bubbles and good mixing. Fine bubbles provide a large gas/liquid interfacial area and a high attachment probability to inclusions, and good mixing enhances the efficiency of impurity transfer."

Jan 1, 2000

By R. Padilla, M. C. Ruiz, R. Villa

"Bismuth is an impurity in copper minerals where it occurs mainly as the mineral bismuthinite (Bi2S3). In smelting of copper minerals, most of the bismuth reports to the white metal, as a result, a substantial amount of bismuth accompanies the copper to the electrorefined cathodes. Thus understanding the behavior of Bi2S3 at high temperatures is crucial to eliminate bismuth before electrorefining. In this paper, some experimental data on the decomposition/volatilization of bismuthinite in nitrogen- oxygen atmospheres is discussed. The results indicated that in nitrogen atmosphere, bismuth volatilization occurs through a fast decomposition of bismuthinite to metallic bismuth and sulfur with subsequent volatilization of bismuth in the range 850-1100 °C. Similarly, in the presence of oxygen, bismuthinite decomposes to bismuth too, followed by oxidation to the non-volatile bismuth trioxide at temperatures higher than 750 °C. Both, temperature and partial pressure of oxygen affect significantly the bismuth volatilization and the oxidation rates.IntroductionCopper sulfide minerals are the major source for the production of metallic copper by pyrometallurgical processes, which are the dominant processes in the production of copper by selectively oxidizing the sulfide sulfur to SO2 and the accompanying iron in the concentrates to iron oxide, which can be conveniently removed as a stable slag.Generally, copper concentrates contain some deleterious minor elements such as arsenic, antimony, bismuth and lead, which are present as sulfides. These elements depending on their concentration may originate problems in the copper smelting processes and they can ultimately lead to a final copper product with unacceptable high levels of impurities.During the treatment of these copper concentrates by smelting, the impurities generally distribute themselves in the condensed and gas phases and they are eliminated mainly through the gas phase [1-3]. Thus, smelter off gases contains substantial amounts of volatilized impurity elements. For example, in the case of bismuth, the estimated distribution of bismuth in flash furnace smelting [2] was 15 % in the matte, 5 % in the slag and 80 % in the gas phase, and recently, for Outokumpu flash smelting Davenport [3] reported the distribution of bismuth as 30-75% in matte, 5-30% in slag and 15 -65 % in the off gas."

Jan 1, 2011

By Wayne Bell, Xiaodi Huang, Matthew Andriese, Jiann-Yang Hwang, Zhiwei Peng

"The equations for determining microwave field attenuation length and half-power depth in magnetic materials were derived from Maxwell’s equations. The microwave field attenuation length and the half-power depth for a magnetite concentrate were calculated and the temperature dependence of them was determined. It is demonstrated the microwave field attenuation length and the half-power depth highly depend on temperature and decrease with increasing temperature up to 900 °C. The variations of field attenuation length and the half-power depth with temperature indicate the microwave power attenuates much faster than the field strength in materials. The evaluations of field attenuation length and microwave half-power depth can be used to characterize the microwave dissipation behaviors in the sample and optimize the dimensions of the material in microwave heating.IntroductionMicrowave has been applied in materials processing for its distinguished advantages including rapid heat transfer, volumetric and selective heating [1,2]. However, most research work involving microwave heating are confined to non-magnetic materials (e.g. ceramics), with limited attention paid to the heating of mixed property materials (e.g. magnetite and other ferrites) under microwave irradiation [3-5]. Since many magnetic materials exhibit good and even better microwave absorption capability than non-magnetic counterparts, it is quite necessary and deserved to take advantage of this property and then improve the heating efficiency. To achieve this aim, further understanding on the microwave heating mechanism, especially the microwave propagation/dissipation behaviors in magnetic materials is required.The dissipation behavior of microwave in materials has been identified as one of the key factors that affect the efficiency of heating under microwave irradiation and this behavior can be characterized by several parameters. Apart from traditional penetration depth (TEM power penetration depth, Dp = 1/(2*a), where a is the TEM field attenuation factor), two other parameters, field attenuation length (Df) and half-power depth (Dh), are also applied to indicate the microwave dissipation in materials [6].The accurate determination of such parameters can help in optimizing the dimensions of the load in a microwave furnace, producing more uniform heating under microwave irradiation and avoiding thermal runaway."

Jan 1, 2011

By R. M. Moon

Neutron scattering has played a crucial role in advancing our understanding of rare-earth materials. It has provided a detailed description of the rich array of exotic magnetic structures; it has confirmed the accuracy of theoretical wave functions for the 4f electrons; and it has provided fundamental data on the collective magnetic excitations in these materials. The fundamental property of the neutron which has been exploited in this work is the magnetic interaction which exists between the magnetic moment of the neutron and atomic magnetic moments on individual rare-earth atoms. This interaction produces scattering of neutrons in a manner closely analogous to the scattering of X rays by atomic charge distributions. In a material exhibiting long-range magnetic order, Bragg diffraction peaks will appear at scattering angles determined by the periodicity of the magnetic structure. The Bragg intensities are determined by the magnitude and relative directions of the atomic moments. The rare-earth metals and alloys are characterized by sinusoidal modulation of magnetic moment components which can be combined in various ways to produce a variety of magnetic structures. The periodicity of these modulations is frequently not related simply to the underlying periodicity of the chemical structure. The major features of these structures are explained by the combined, and sometimes competing, exchange and crystal-field interactions. At a more fundamental level, neutron diffraction also gives information on the spatial distribution of a magnetic moment in a rare-earth atom. This moment comes from the 4f electron shell, and accurate measurements of the neutron scattering amplitudes have been used to check the accuracy of atomic wave function calculations for the 4f electrons. It was found that relativistic Dirac-Fock calculations are in excellent agreement with the experimental results. Collective excitations of ordered magnetic systems are described in terms of spin waves, which are sinusoidal modulations in space and time of the direction of the ordered moments. Inelastic neutron scattering is used to measure the energy and wave length of these collective excitations. Analysis of these data gives direct information on the interatomic interactions responsible for the magnetib properties of these materials.

Jan 1, 1992

By F. Nava-Alonso, O. Alonso-González, A. Uribe-Salas, R. Pérez-Garibay

"Cyanidation is the most used method to recover gold and silver from their ores. In this process, other metals besides gold and silver may sometimes dissolve and interfere with the efficiency of extraction. Copper is one of those metals, reaching concentrations as high as 1000 mg/L in some cyanidation plants, making difficult the extraction and purification processes, and increasing the operating costs.This preliminary work was intended to study the feasibility of using amines to form a precipitate and to eliminate copper from a synthetic solution containing high copper and cyanide concentrations, as is the case of some cyanidation effluents. The solid formed is removed from the solution using conventional filtration techniques. Seven amines were evaluated at different pH values and amine additions. Up to 90% of copper present may be removed at the natural pH of the effluent (alkaline). The remaining copper would permit to recycle the solution back to the cyanidation process. IntroductionCopper is generally considered the most problematic metal in gold leaching due to the rapid formation of copper cyanide complexes when some readily-soluble minerals are processed (e.g., azurite, malaquite, cuprite, chalcocite and bornite). The copper solubilization as cuprous cyanide complexes leads to a significant economic penalty in terms of excessive cyanide consumption and high cost for cyanide elimination. When activated carbon is used to recover gold and silver, the copper-cyanide complexes decrease the efficiency of the process because of the competition of the cuprocyanides with the aurocyanide for the adsorptive sites on the activated carbon (Rees and Deventer, 1999).Several techniques have been developed to attempt to overcome the problems caused by the copper presence in cyanidation solutions, notably: acidification-volatilization-regeneration (AVR), ion exchange-electrolysis or solvent extraction-electrowinning (Lu et al., 2002). In this work the use of some amines is proposed to remove the copper-cyanide complexes by precipitation of a copper-cyanide-amine solid. The process was evaluated for different amine additions and pH values, using copper-cyanide synthetic solutions of composition similar to that presented by some cyanidation plants with high copper."

Jan 1, 2008