Search Documents

By Hidenori Okamoto, Katuto Itoh

"Nippon Mining & Metals' Hitachi Refinery refines 40% of the anodes produced at its Saganoseki Smelter & Refinery. Its current annual production stands at 180,000tons.The refinery always endeavors to increase productivity. One of the outcomes of its efforts is an originally developed automatic short-circuit detector used to inspect short-circuits between anode and cathode. The detector is designed to inspect the 56 pairs of anode and cathode in a cell by fluxgate sensors at once. It inspects 564 cells, automatically and un-manned, and gathers data to be put into a computer. The development of the detector led to a reduction of man-power and achieved a detection accuracy superior to that of a hand-held gauss-meter. In addition, statistical and historical processing of the data enabled early detection and early recovery of the cells with poor efficiency.The new system also contributed to raising the refining capacity and reducing the unit steam consumption, because it is possible to inspect even the cells covered with thermal insulation sheets.IntroductionInspection of cells is an important component of the operation management of a tank-house. At the Hitachi Plant, it used to be carried out by two workers who walked on and checked all the cells of its tank-house once a day to find out any short-circuits in the cells, using hand-held gauss-meters. They inspected about 33 thousand pairs of cathodes and anodes a day and removed nodules by hammers. This method had following problems:it needed much manpower.the walk on the cells sometimes deranged electrodes positions.there was radiation-loss connected with the inspection due tothe fact that the workers were obliged to uncover thermal insulation sheets on the cells while inspecting."

Jan 1, 2000

By Tracey Brommer, Britt Elin Gihleengen, Elsa Olivetti, Randolph Kirchain

"Increased demand resulting from the economic and environmental advantages of recycling secondary materials has constrained secondary material supply. As a result of constrained supply, the conventional strategy to maximize recycled content in an individual aluminum alloy must be expanded to maximizing total recycled content in a given production period. This work compares the performance over a two week period of an actual remelter for two strategies; a sequential charge-by-charge optimization framework and an integrated approach that explicitly incorporates the production schedule. Optimizing across the entire two week production is found to increase recycled content and minimize primary and alloying material additions. It is expected that as the scrap material market continues to be constrained by high demand, longer term batch planning strategies that can optimize material allocation will deliver improved performance.IntroductionIntensifying economic and environmental pressure to incorporate secondary aluminum into products is pushing remelters to explore additional strategies and tools to increase recycled content. Aluminum remelters are exploring alternative sources of secondary materials because of constrained secondary material supply and relatively high primary and secondary material cost [1]. Computational models, such as blending models are a tool that could help industrial remelters mitigate supply and cost challenges and thereby increase recycled content. In particular, computational tools can help manage the incorporation of new raw materials of variable quality. Blending models find many industrial applications and have been explored for over sixty years originating with the classic nut-mix problem dating back to 1950’s [2]. Blending models optimize the raw material input to make a desired product subject to a series of constraints such as product specifications and material availability. Deterministic and linear blending model formulations are presently implemented in some industrial aluminum remelters [3]. The primary reluctance of aluminum remelters against computational model implementation is the incapability of their blending models to reflect the intricacy of industrial remelting conditions [4]. For example, to reduce calculation time, industrial aluminum blending models usually optimize a batch plan for a single alloy and are not formulated to optimize several products simultaneously. Since such a model does not include knowledge of subsequent charges in the optimized batch plan, the resulting batch plans tend to deplete the “cleanest” secondary materials leaving the more uncertain and compositionally challenging materials for later charges. As a result, a remelter may override the calculated batch plan or leave certain scrap materials out of the material input to conserve these materials for alternative products scheduled for later production. This work explores an alternative aluminum charge planning tool that can optimize across an extended production schedule and compares it to a heuristic sequential optimization strategy reflecting an industrial remelter."

Jan 1, 2012

By R. I. Rodriguez

Since the 1973 energy crisis, high fuel oil costs have been eroding the economics of the Nicaro and Punta Gorda Plants that employ the Caron Process for laterites processing. Since 1995, Cuban crude oil production has growth dramatically, with progressive utilization in power generation, cement and nickel plants. This paper shows how Nicaro and Punta Gorda plants have been able to shift from expensive Bunker C Fuel Oil to heavy but cheaper Cuban Crude Oil of high Sulfur content and achieve a significant reduction in operating cost. Problems related to the high sulfur content of the Cuban crude oil have demanded extensive investigations of the process chemistry and novelty solutions are proposed, with corresponding changes in process conditions. Innovative options are shown that will allow further cost reductions in the future. Keywords: Cuban Crude Oil, Sulfur, Ammonia.

Jan 1, 2004

By Christopher M. Moore

DK Recycling und Rohelsen GmbH converts 380 000 annual tonnes of iron containing waste materials Into pig Iron. Zinc Is the main reason that these materials are classified as waste. The materials are processed In the conventional way by making sinter which is then smelted in a blast furnace to foundry grade pig iron. The trick lies not in the unit operations which are quite standard but rather In the modifications made to the plant and operating procedures to cope with the much higher levels of tramp elements.

Jan 1, 1995

By Julien Favre, Akihiko Chiba, Damien Fabregue, Yuichiro Koizumi, Eric Maire

"The mechanical behavior of Co-20Cr-15W-10Ni alloy is studied by compression tests at high temperature. Microstructures after deformation are evaluated using SEM-EBSD. Significant grain refinement occurs by dynamic recrystallization for high temperature and low strain rate (T>1100°C, <0.1s-1), and at high strain rate (~10s-1). Dynamic recrystallization is discontinuous and occurs by grain boundaries nucleation, leading to a necklace structure. The nucleation mechanism is most likely to be bulging of grain boundaries. However, recrystallization occurs also by rotation of annealing twins which can bulge as well. The modeling of mechanical behavior gives a fair quantification of flow softening due to dynamic recrystallization, indicating the progress of dynamic recrystallization with deformation.IntroductionCobalt-chromium alloys are used in biomedical applications for the elaboration of implants due to their outstanding mechanical properties and their high resistance to corrosion. For stent application a large ductile behavior is required in addition to the high mechanical strength. Indeed stents have to undergo a deformation until e˜40% during their expansion [1]. Conventional Co-Cr-Mo (CCM) alloys exhibit limited ductility (maximal deformation about e˜30%) [2]. Co-Cr-W-Ni (L-605) alloy is a better candidate for stent elaboration since its fracture strain can exceed 40% (comparable to nickel superalloys (Figure 1), while it keeps high mechanical strength. In spite of the presence of nickel element in this alloy, biocompatibility is sufficient for vascular implants, therefore L-605 alloy is extensively used for heart valves and stent elaboration [3]."

Jan 1, 2012

By E. Gutierrez-Miravete

A computational method for the simulation of mold filling processes is described. The method is based on the representation of the flowing or deforming medium as a collection of mutually interacting parcels of material. Instantaneous positions of individual material parcels are calculated by numerical integration of the dynamic equations, subject to appropriate initial and boundary conditions. So far, the method has been used to produce qualitative simulations of some flowing and deforming systems encountered in mold filling technology, and our findings are summarized herein. In all cases, individual material particle motions can be followed in detail, allowing critical examination of potentially problematic mold design features.

Jan 1, 1992

By V. Gornitz

The Orphan mine uranium deposit, Grand Canyon, Arizona, is a cylindrical collapse-breccia pipe, 70 to 150 m in diameter and 500 m deep. Pipe fill was derived from the Supai Group, Hermit Shale, and the Coconino Sandstone. Uraninite, with Cu, Fe, Pb, Zn and Ni-Co sulfides is concentrated along the pipe boundary ring fracture (annular ring) and within the central porous sandstone matrix. There is some suggestion of vertical and lateral zonation of U with respect to Cu. Reduction of ferric oxide cement from red beds and recrystallization of carbonate, with formation of kaolinite preceded major ore deposition. Early Ni sulfides, arsenides and disseminated pyrite were followed by massive pyrite, and botryoidal uraninite, which in turn was suc-ceeded by Cu, Zn and Pb sulfides. A second, later generation of uraninite was closely intergrown with hematite and base metal sulfides. Oxidation of primary minerals may have been associated with Tertiary regional uplift. The paragenetic sequence closely resembles that of other Grand Canyon breccia pipes, except for the extensive development of the distinctive uraninite-hematite association. Mineral assemblages at the Orphan suggest possible mixing of the metal-bearing solution(s) with a more oxidized fluid, containing soluble uranyl complexes. Homogenization temperatures of fluid inclusions in calcite (GO-lIO?C) at the Orphan fall within the lower end of the range observed at other breccia pipes.

Jan 1, 1987

By Carl C. Nesbitt

A study was conducted to examine the treatment of metal-bearing effluents by precipitating the metals as sulfides and simultaneously collecting the particles by flotation. The precipitant was hydrogen sulfide gas which was introduced into a bench-scale column cell with air. The study included experiments of various flotation reagents and column configurations in treating solutions containing dissolved copper, lead, mercury, iron, zinc and cadmium. An acidic laboratory waste from a local copper operation was used to test the column with a solution containing several metals and arsenic. Precipitates were observed to form at the gas/liquid interface when the gas mixtures were rich in H2S. Copper, mercury, lead, and cadmium were precipitated from solution as sulfides to concentrations near detection limits. The flotation of these precipitates was enhanced with small amounts of S-7151 promoter from American Cyanamide Company and Dowfroth 1263 mixed with the feed. The recovery of the precipitates in this manner produced a smaller volume slurry which was easier to dewatering than a slurry produced by conventional precipitation techniques. The low pH and high oxidation-reduction potential in the cell from H2S addition was not conducive to form precipitates of iron, zinc or arsenic. However, these ions were precipitated as sulfides by raising the pH of the column discharge.

Jan 1, 1994

By Andrew B. Suttie

The lead-acid battery recycling industry was seriously affected during the 1980s by increasing environmental protection costs and poor lead prices. The process is now being repeated in the 1990s causing further difficulties, for recyclers. In Europe, many lead-acid battery recycling plants use rotary furnaces. The Darley Dale smelter, redeveloped between 1984-87, uses only rotary furnaces. A review of options for this plant has been completed and &apos;concluded in favour of further investment to exploit more fully the benefits of rotary furnace technology.

Jan 1, 1995

By Mônica Suede Santos Silva

This work describes characterization of the performance of the tundish of a six strand continuous casting unit of the Companhia Siderúrgica Belgo Mineira, João Monlevade, Brazil using physical modeling. Permanent and transient conditions, due to ladle metal composition changes are considered. Pulse and step tracer addition techniques are employed to assess the control variables. For transient conditions the degree of inter-mixing and the minimum residence time are determined with a view to optimize the process especially during the grade changes of steel.

Jan 1, 2003

By E. S. Geskin, W. L. Chen, A. Vora

"This paper is concerned with the application of an abrasive waterjet for metal shaping. The waterjet cutting technology uses water compressed to the pressure up to 55,000 psia which is accelerated in a cylindric nozzle. Abrasive particles are then supplied into the water stream and accelerated by the water. Cutting occurs via the interaction between the water-particles stream and a workpiece that causes material erosion at the impingement zone. The mechanism of this interaction enables shaping of practically any material with a minimal effect on the metallurgy of subsurface. The motion of the jet penetrating through a material body is guided by a robotic arm. A waterjet cutter is becoming one of the principal tools for shaping titanium, super-alloys and other hard-to-machine metals and composites. The shaping, resulting from the waterjet cutter, is very similar to laser beam cutting. However, unlike laser processing, there is no damage to the subsurface structure.The presented work discusses the experimental study of cutting of titanium plates. The results of these experiments demonstrate the potential of the abrasive waterjet as a shaping tool. IntroductionOne of the main avenues in the development of metal shaping is the use of high energy beams as cutting tools (1,2). There are a number of advanced beam oriented material removal technologies, such as laser, electron beam, plasma and abrasive waterjet (AWJ) cutting. The advantages of AWJ cutting are well understood and documented (3-14). This technology has the potential of becoming the principal tool for netshaping and netsurfacing of parts. However, the use of AWJ is currently limited to cutting of hard-to-machine materials such as titanium, superalloys, glass, composites, etc. The cost of A W J cutting is much higher and the productivity is much lower than those of the thermal cutting. At the same time abrasive waterjet can be used for shaping any existing technological material from fabrics, plastics, aluminum to glass, composites, and diamonds. The material losses during AWJ shaping are minimal. The roughness and waveness of the surfaces generated during AWJ cutting are substantially less than those of the thermal cutting. Due to the size of the jet cross-section total force exerted by the jet on a workpiece does not exceed 30-50 newtons. This terminates the need in the use of complex fixture for material holding. Low applied forces and low surface temperature prevent the damage of metal subsurface in the course of cutting. The small size of the impingement area will determine the limited width of the kerf. Due to the size of kerf and unidirectional character of the water jet the formation of practically any metal contour is possible."

Jan 1, 1988

By J. L. Hill, M. A. R. Sharif, J. Lin

"A numerical algorithm has been developed to simulate the movement, breakup, and entrapment of the oxide film inclusions encountered during the mold-filling processes of aluminum castings. The flowfield is solved using the well-known Marker and Cell (MAC) method by a time marching process. The Volume of Fluid (VOF) method is used to track the free surface boundaries. A kinematic approach is employed to track the movement and breakup of the oxide films on the free surface or in the bulk liquid metal. The computer program based on the proposed algorithm is able to model the flow behavior and oxide film movement, breakup, and entrapment in mold cavities for aluminum castings.IntroductionMetallographic and fractographic studies of the aluminum castings show tangled networks of oxide films in the castings. These oxide films can form in the furnaces or during the mold filling processes. Green and Campbell [I] concluded that the oxide film defects dominate the strength of aluminum castings. The main cause of oxide film entrapment into the bulk molten metal during the casting processes is the surface turbulence. In film-forming alloys, if the surface breaks, due to a drop, a fountain, or a breaking wave, then the surface film is folded over and incorporated into the bulk liquid. The incorporation of surface films leads to cracks in the casting and other defects that are nucleated by the presence of the folded films, such as porosity and hot tears. Campbell [2] estimated that up to 80% of scrap in light-alloy casting is the result of surface turbulence."

Jan 1, 1999

By Yoshihiko Maeda

It is said that the 21st century will be an era of the remedy of the global environment. In order to reserve natural resources for the future and to avoid the dispersion of heavy metals after usage and to avoid pollution problems, it is extremely important to recycle heavy metals as much as possible by reasonable recovery procedures. The nonferrous metal industry is expected to play a important role in the recycling of heavy metals that are originally their products. From the depressed metal price experienced in Japan in 1980&apos;h due to the sudden change in current exchange rate between US dollar and Japanese yen, one of major nonferrous metal company, Dowa Mining, has diversified its business area not only to the so-called down stream, but also to the environmental business including metal recycling, industrial waste treatment and soil remediation by utilizing technologis and facilities once used or still used for mining and smelting of copper, zinc, lead and precious metals. In this paper some of these applications will be presented.

Jan 1, 2003

By T. Shibasaki

There is a strong demand in the photo industry to the higher quality of refined silver. Osaka Refinery produces about 27 mtpm of refined silver mainly from copper refinery slimes. Product quality is attained by controlling the impurity level in electrolyte. Copper is cemented with silver oxide and palladium is precipitated by a chelating agent. Both processes were operated previously in batchwise for treatment of bled out electrolyte, Recently these processes have been improved and made continuous to cope with the increased impurity.load. As a result the grade of fine silver has been maintained steadily at Pd < 3 ppm and Cu < 5 ppm.

Jan 1, 1989

By K. S. Han, M. Yoshimuura, H. Fujita, Y. Sato, S. W. Song

"Film of LlCoO2 as cathode material for rechargeable lithium microbatteries has been fabricated on the platinum metal substrate by electrochemical-hydrothermal method in concentrated LiOH solution at 200 °C as Soft Solution-Processing. The film fabrication has been understood in terms of dissolution of cobalt metal powders and subsequent oxidative deposition on the substrate. The film structure was characterized using scanning electron microscope, X-ray diffraction analysis; X-ray photoelectron spectroscopy and micro-Raman spectroscopy.IntroductionRapid growth of wireless communications and emerging integrated optoelectronic circuits caused the miniaturization· cif electronic devices, thus the demand for high energy density microbatteries as a power source for the microelectronics increases. In this regard, all solid-state lithium microbatteries including LiCoO2 and LlMn2O 4 [l-4], the most promising intercalation cathode material, have been developed. However, major difficulty of .fabrication of a lithium microbattery arose from the preparation of cathode film, according to a· recent report on Rare Metal News [5]. Although many attempts have been made to deposit the cathode films, all those methods are mostly chemical vapor deposiiton (CVD), various evaporation, sputtering techniques and spray pyrolysis. These methods require preparation of bulk cathode materials cir its precursor, then deposition with complicated instruments including high· vacuum system, and even postsynthesis annealing to obtain desire electrochemical 'properties. It is clear that all of these techniques are neither economic nor environmentally friendly. Compared to those methods, film form.ation from an aqueous solution is thought to be simpler and more economical, and requires much· less energy consumption. Our .group has demonstrated the utility of Soft SolutionProcessing [6,7], which is defined as environmentally friendly processing using (aqueous) solutions, to produce films of a variety of functional solid materials. According to the Pourvaix's diagram [8], some metal can be dissolved in an alkaline solution and consequently combined with hydroxyl group or oxygen anion forming metalate or metalite. Cobalt also seemed to form cobaltite, HCoOi in strong alkaline solution in the Pourvaix's pH-potential diagram. Based on this information, it was expected that LiCoO2 could be prepared using the cobalt metal in Li OH solution by Soft Solution-Processing. Recently, we reported the successful single step fabrication of electrochemically active LlCoO2 films on the cobalt metal substrate by hydrothermal methods without any post-synthesis annealing as Soft SolutionProcessing [9,10]. Film formation mechanism could be elucidated by the following evidences. . As expected from Pourvaix's diagram, cobalt metal was dissolved in concentrated LiOH solution forming dissolved cobalt species which was detected by an observation of absorption band in UV-VIS absorption spectrum [10]. Thus the reaction was assumed to be started from dissolution. Time dependent potential of Co electrode exhibited only one-step evolution with 0.6 eV from Co metal to LiCoO2 [10]. Another strong evidence was the finding of LiCoO2 powder precipitates at the bottom of tetlon beaker after the reaction [11]. Based on those experimental findings, it was understood that film is formed by dissolution-precipitation mechanism [9-11]."

Jan 1, 2000

By R. E. Fanning

"IntroductionThe Aluminum industry is one of many materials industries which strive to make their material the preferred choice for large volume products. In some applications one material has a natural advantage over others, but more frequently several materials compete with one another, each providing one or more advantages and some trade-offs. Customers may design their product with several objectives such as minimum system cost, maximum customer appeal or maximum manufacturing flexibility, choosing materials which best combine cost and performance. In such markets it may become necessary for a material supplier to enhance the attractive features of the particular material to outweigh its disadvantages.It is difficult, if not impossible, to predict how various materials will evolve. Technological breakthrough, government regulations, material availability or sociological issues may redefine the balance between competing materials. In spite of some uncertainty regarding the competitive position of competing materials, there is little doubt that unrelenting pursuit of product quality improvement and cost reduction are essential to future viability of the aluminum industry. It is the intent of this paper to identify some areas where technological improvement would be beneficial. Thus this paper is a collection of briefly described problems that will hopefully stimulate the thoughts and research required for knowledge based solutions. Rolling ProcessA particular example is the beverage can industry where aluminum, steel, glass and plastics vie for a share of the m.arket. The high cost of aluminum relative to steel or glass requires minimizing the amount of metal per can. The high intrinsic value of aluminum has led to extensive recycling of cans although net metal cost is still higher than that of the competing materials. Intensive engineering of the beverage can led to improved design and better understanding of material requirements. These improvements permitted substantial reduction in sheet thickness over the past decade. The downward trend in metal thickness for beverage can sheet is shown in Figure 1."

Jan 1, 1988

By Nathaniel R. Quick

"Nd: YAG, KrF excimer, and Cu-vapor lasers are used in air to synthesize conductors and semiconductors as a second phase in silicon carbide and aluminum nitride. Conductor resistivities as low as 104 O-cm are formed in these substrates; the resistivities for the untreated substrates range from 10 11to 1014 O-cm. The silicon carbide conversion is relatively independent of wavelength while the aluminum nitride conversion shows a dependence on wavelength over the range 248 nm to 1064 nm. Silicon carbide conductors, evaluated over the range 15 K to greater than 300 K, exhibit metal like conductivity; resistivity increases with temperature. Silicon, carbon, and oxygen are identified as the principal chemical species associated with the conductor in SiC substrates while aluminum, nitrogen, and oxygen are identified as the principal chemical species associated with the conductor in aluminum nitride substrates. The silicon carbide system, which has the less complex phase diagram, is evaluated in more depth to explain the synthesis mechanism. Oxygen was principally on the surface and increasing SiC conductivity is associated with decreasing spacing between 5 µm, or less, diameter carbon globules. This technology is proposed as a replacement for metallization in electronic packages, sensors and devices. INTRODUCTIONCeramics are commonly used for multichip module, hybrid and multilayer electronic packaging; semiconductor device and sensor applications because of the insulating, conducting, semiconducting, or superconducting properties that these materials possess (1,2) The majority of ceramics, however, have not been known to exhibit conductive or semi conductive properties when exposed to rapid thermal heat processing. A ceramic and process which through selective conversion can combine two or more of these electrical properties to eliminate the need for metallization is of interest to both the commercial and military sectors."

Jan 1, 1994

By Zhenyang Wang, Yiran LIU, Xiangdong Xing, Jianliang Zhang, Zhengjian Liu

Basic characteristics of marine placer were systematically studied by chemical analyze, scanning electron microscope and X-ray diffraction in this paper. It could be found that the marine placer mainly consists of titanomagnetite and titanohematite. A series of experiments were performed to investigate reduction-magnetic separation for Fe and Ti from the marine placer. Effects of reduction temperature, reduction time, carbon ratio, magnetic density, and grinding fineness on the reduction-magnetic separation process were investigated. And the optimal process parameters were obtained as follows: the reduction temperature 1300, the reduction time 30 min, the carbon ratio 1.1, the magnetic density 50mT, and the grinding fineness of 0.074μm 86.34%. Under such conditions, the metallization rate, iron grade of magnetic substance and iron recovery reached to 94.23%, 97.19% and 90.28% respectively, and the titanium grade in non-magnetic substance and recovery of was 57.94% and 87.22% respectively. The effective separation of iron and titanium could be achieved in reduction-magnetic separation process.

Jan 1, 2015

By R. Kramer

During foundry sand reclamation process development, molds formed from reclaimed chromite sand showed a rapid decline in tensile strength during thermal cycling tests. Because this characteristic could limit reuse of chromite sand in the. foundry, the sand was examined in detail Scanning electron microscopy, x-ray mapping, magnetic susceptibility, and x-ray diffraction were utilized to evaluate processed chromite sand. It was found that process variables such as binder composition, reclamation temperature, and processing method had a significant effect on the chromite sand particle surface. X-ray diffraction indicated a crystallographic change in the processed sands. Magnetic susceptibility also increased after processing. Diffusion of iron to the particle surface and increased surface roughness were identified as potential causes of the decreased tensile strength in the molds.

Jan 1, 1991

By R. D. Pehlke

The history and present status of continuous casting of steel are reviewed, including a genera 1 description of current processes. Plant layout, process development and elements of machine component design are outlined, and key steps in integration into a stee-1 production system are detailed. Recent productivity advances and improvements in quality are described. Process developments are reviewed, and some future avenues for this technology are considered.

Jan 1, 1985