Search Documents

By Junwei Han, Wenqing Qin, Dawei Wang, Fen Jiao, Wei Liu

The removal of iron impurity from zinc calcine was studied by magnetization roasting and magnetic separation. The effects of roasting temperature, magnetic intensity, ore grinding, and leaching pretreatment on iron grade and recovery were investigated. The results indicated that iron recovery increased with the increase of roasting temperature or magnetic intensity, while iron grade was always less than 22%, depending on the fact that the magnetite were not liberated completely. The good liberation was difficult to be achieved by ore grinding but was easier by acid leaching, since the magnetite grains were very fine. After the leaching pretreatment, the recovery of 76.31% with iron grade of 53.24% was obtained by one roughing and cleaning. The SEM/EDS analysis showed that a part of sphalerite, zinc ferrite and other gangues were mixed into the iron concentrate, while some of fine magnetite was reported to the tailing.

Jan 1, 2016

During electrowinning of nickel chloride, hydrochloric acid was regenerated instead of chlorine in a two membrane cell, by segregating the chloride catholyte with an anion exchange membrane, and the sulphate anolyte with a cation exchange membrane from the middle electrolyte (ampholyte) compartment. Successful operation of such a cell depends on controlling chloride leakage through the cation exchange membrane to the anolyte. Small amounts of chlorine gas could be detected in the oxygen evolved at the anode. In this paper, the chloride. leakage as a function of various types of cation exchange membrane and different composition of the anolyte is reported and discussed. Ag+ was added to the anolyte to eliminate chloride leakage to the anode. The cell voltage, electrode potential and voltage drop over the membrane as a function of current density has also been investigated.

Jan 1, 1996

By Xinzhong Deng, Naixiang Feng, Kejia Liu, Jianping Peng, Yaowu Wang, Yi Zhang, Yuezhong Di

Low-carbon Ti2O3 was prepared by carbonthermal reduction of the mixture of titanium dioxide and activated carbon at vacuum condition. The kinetics and phase evolution of Ti2O3 formation process were investigated through X-ray diffraction and gravimetric analysis. The only intermediate phase detected is Ti3O5. The reduction time was reduced sharply to 4 h when temperature was raised to 1300 °C. The best molar ratio of activated carbon and TiO2 is 0.6–1. At this condition, the content of Ti2O3 in slag is up to 95.63% and the content of the carbon element is below 0.004%, which meets the requirements for the further preparation of metal Ti by FFC Cambridge process. At the same time, the microstructure of Ti2O3 generated presented porosity, which would promote the electro-deoxidation process extremely.

Mar 1, 2017

By L. Cifuentes

Electrodialysis (ED), i.e. a technique based on the effects of electrically charged membranes on ions in solution in an electric field, has been applied to Cu-Fe-As-Sb- H2SO4 electrolytes similar to those used in copper electrorefining and electrowinning operations. The effects of current density, time and species concentration have been studied in a batch ED cell. The technique has shown to be effective in concentrating and separating a range of ions and points to possible new methods of treating copper electrometallurgy effluents.

Jan 1, 1999

By Edgar Blanco

A thermodynamic and experimental investigation to develop a new process for converting molybdenite concentrate to molybdenum dioxide by a water-vapor oxidation process was carried out. In addition, the behavior of rhenium and selenium in molybdenum concentrate during the process was investigated. The kinetics of the reaction were determined by measuring the weight change of a sample with time in water vapor at temperatures between 700-1000°C. The results were analyzed by a Shrinking Unreacted Core model under chemical reaction control, which showed an activation energy value of 102 kJ/mol. To determine the behavior of rhenium and selenium, their concentrations in the molybdenum sulfide and the product molybdenum dioxide were measured by the use of ICP. While most rhenium remained with the molybdenum dioxide after the water vapor oxidation, almost all selenium volatilized. These results agree with thermodynamic analysis.

Jan 1, 2006

By C. J. Parradies

During injection into a die, semi-solid metal alloys exhibit a shear-rate, history-dependent flow response. Simulating the injection of a thixotropic material requires that empirically determined boundary conditions and viscosity are specified as a function of both temperature and shear rate history. Experiments were performed using an industrial die casting machine that was instrumented with sensors to measure the pressure and temperature during the injection of a semi-solid aluminum alloy through a tube. This benchmark experiment was used to develop a simulation of the die casting process that could then be applied to more complex die geometries. The results of the experiments were analyzed using the exact, steady state solution for a power law fluid and simulations accounting for slipping at the boundary between the semi-solid metal and the die. Results indicated that the no-slip condition cannot be used to simulate the velocity boundary condition, because the measured pressure is much lower than that predicted by the models. An estimated apparent slip coefficient was introduced to account for the reduced pressure. During some of the experiments, a sudden drop in the measured pressured, prior to decreasing the ram velocity, coincided with observations of segregation in the form of concentric rings visible on the polished surface of cross-sections cut from material remaining in the tube.

Jan 1, 1997

By Gui-fang ZHANG, Zhe SHI, Lei GAO

Secondary V-recycling slag, an industrial waste containing high gallium is being dumped continuously, which causes the loss of gallium. Thus, the alkali fusion process was employed to recover gallium from this slag. The effects factors on extraction of gallium such as roasting temperature, roasting time, alkali fusion agent concentration and CaO concentration were investigated in the paper. The experimental results indicated that excessive roasting temperature and roasting time is unfavorable to the recovery rate of gallium. The appropriate roasting temperature and duration are 1000 and 2 hours, respectively; The appropriate proportioning of Na2CO3: NaOH is 2:1 when the concentration of alkali fusion agent weighs 0.4 times the mass of the slag; In order to remove SiO2 from the leaching liquor, CaO should be used as an additive in the roasting process. The appropriate concentration of CaO should weigh 0.2 times the mass of the slag. Employing these optimal alkali fusion conditions in the roasting process, gallium recovery is above 90%

Jan 1, 2015

By Shusen Cheng, Kun Yan

A three-dimensional mathematical model of hot blast stove pipe shell has been established and used for analyzing the stress distribution and deformation. The results show that stress concentration happens along the intersection line of hot blast main and the hot blast manifold. There is no plastic deformation on the whole pipe region. The shell near the intersection elongates along the vertical direction and shortens along the horizontal direction, and deforms into an oval. The shell of hot blast main rises up, and inclines upward around the end of hot blast main. The hot blast main moves away from the hot blast and the displacement near the middle region is larger, the main deforms into an arch on horizontal surface. The deformation of shell may form a gap between shell and refractory inside and damage the security and stabilization of hot blast stove piping.

Mar 1, 2017

By Shusen Cheng, Dongdong Zhou, Yongqiang Bai

The strength of sinter could affect the permeability and CO gas utilization of blast furnace, and one of the main impacted factors of sinter strength is crack. With the widely use of vanadium-titanium sinter in China, the blast conditions of some blast furnaces became worse since the vanadium-titanium sinter has been added. However, there have little public research for this phenomenon. In this paper, the influence of titanium content on the sinter ore phase structure and crack were studied by DMRX polarizing microscope. In addition, the influence of basicity and oversintering on the sinter ore phase structure were also investigated. The observed results of vanadium-titanium sinter were compared with typical sinter in China, and the influence law of titanium content on the sinter ore crack was obtained.

Mar 1, 2017

By Markus A. Reuter, Jacob Wood, Robert Matusewicz

Over the last 20 years, significant improvements in copper smelter productivity have been realized through the advent of continuous smelting processes. This progress has until recently however, not been carried through to copper converting. Peirce-Smith converting has been widely used by the copper industry for 100 years but is limited by its batch nature in achieving large scale of production. A logical next step is therefore copper converting on a continuous basis with its inherent environmental benefits. A number of continuous converting technologies are currently in use or being developed within the copper industry, the majority of these operating with calcium-ferrite slags. A notable exception however is the Ausmelt Continuous Copper Converting (C3) technology which has focused on operation with ferrous-calciumsilicate or loosely called olivine type slags. This paper discusses the merits of the Ausmelt C3 process and the advantages offered in terms of operational flexibility and process control arising from the use of lime modified iron silicate slags. It also examines the effects of key process variables pertinent to continuous copper converting from both a theoretical and experimental/operational perspective.

Jan 1, 2009

By Wenxuan Xu, Shusen Cheng, Tian Chen

Pulverized coal injection (PCI) can generate heat and reducing gas in the raceway and replace some expensive metallurgical coke in the blast furnace ironmaking process. In this paper, a three dimensional mathematical model of the raceway including the coke bed has been developed to simulate the complicated phenomena of pulverized coal injection. The effects of oxygen enrichment, particle diameter in the raceway are investigated in this study. The establishment of the 3D model is expected to analyze the raceway working state accurately and optimising the PCI operation of blast furnaces.

Mar 1, 2017

By G. O. Onyedika, M. U. Obidiegwu, G. C. Onuegbu

The effect of kolanut (KN) filler and compatibilizer (maleic anhydride) contents on the transport of toluene through low density polyethylene (LDPE) and low density polyethylene composite were studied at the temperatures 40, 60 and 80 °C.The kolanut powder used was ground to 25 μm particle size. In preparation of composite 0–5 wt% of kolanut powder and 0–2.5 wt% of the compatibilizer were mixed with 200 g of low density polyethylene in an injection moulding machine. The injected polyethylene and polyethylene/kolanut composites (LDPE/KN) were taken for sorption test. The sorption data obtained for low density polyethylene and kolanut powder filled low density polyethylene at the different temperature investigated were expressed as the molar percentage uptake (% Qt) of toluene per gram of the kola nut composites. Results show that the uptake of toluene at the five filler content (0–5 wt%) generally increased with increase in sorption temperature but decreased with increase in compatibilizer and filler contents. This can be seen at 80 °C and 0, 1, 1.5 and 2.5 wt% of compatibilizer respectively. The molar percentage uptake of toluene at 1 wt% of filler yielded the following values; 8.6789, 8.4768, 8.3476 and 8.2679 respectively. At 2 wt% it yielded 8.6224, 8.1333, 7.9525 and 7.9042 respectively, at 3 wt% it gave 8.4336, 7.9450,7.8900 and 7.7823 respectively, at 4 wt% it yielded 8.0263,7.9614,7.8218 and 7.6800 respectively and at 5 wt% it gave 7.9635, 7.8630, 7.6256 and 7.5013 respectively.

Mar 1, 2017

By Zhigan Deng

Ni–Mo ore is a black shale containing amorphous colloidal sulfides which have highly active. The oxygen pressure leaching behavior of nickel from black shale in aqueous media is presented. The effects of agitation speed, temperature, oxygen partial pressure and particle size on the rate of nickel leaching were determined. The results indicate that at low temperature hydrothermal and excess oxygen presence, the amorphous sulfides are easily oxidized to sulfuric acid and sulfate, and leaching nickel. The mathematical analyses of the experimental data for various experimental conditions indicated that the dissolution process was controlled by the chemical reaction during the early stage of dissolution, and was then controlled by liquid-film diffusion. In the initial stage of leaching, the reaction depends on oxygen partial pressure.

By He Jing, Wang Changhong, Chen Yongming, Wu Yanzeng, Yang Xiyun, Tang Chaobo, Yang Shenghai

Pitting of Hf in Et4NBr t-butanol and acetonitrile (ACN) solutions was studied by means of cyclic voltammetry, potentiodynamic anodic polarization,galvanostatic, potentiostatic and impedance techniques. The potentiodynamic anodic polarization curves did not exhibit an active dissolution region near corrosion potential due to the presence of an oxide film on the electrode surface, which was followed by pitting corrosion resulting from the passivity breakdown by the aggressive attack of bromide (Br−) ion. The pitting potential (Epit) increased with increasing potential scanning rate but decreased with increasing temperature and Br− concentration. Cyclic voltammetry and galvanostatic measurements allowed the pitting potential (Epit) and the repassivation potential (Ep) to be determined. Analysis of the potential/time transients revealed that the applied anodic current density had a significant influence on the values of Epit. On the other hand, the Ep values were independent on the applied current density. The current/time transients indicated that the incubation time (ti) for passivity breakdown decreased slightly with increasing potential and solution temperature. The impedance spectra showed that the resistance of passive layer decreased with increasing potential.

Mar 1, 2017

By Terence Makanyire, Animesh Jha

The dissolution and chemical properties of vanadium, zirconium, and niobium in rutile lattice are analyzed by comparing the octahedral site preference energies, with respect to Ti4+ ion in the solvent phase. The oxides are often present in rutile lattice and interfere in achieving the quality of pigment grade TiO2 due to favourable Gibbs energy for dissolution in the solvent rutile matrix. Binary mixtures of V2O5 { TiO2; Nb2O5 { TiO2 and ZrO2 { TiO2 with compositions of 80, 85, 90, 95 and 97 wt% TiO2 were made, pelletized and sintered at 1100 °C for 24 hours. The solidsolution mixtures were then cooled and leached in 2M NaOH for 3 hours at 60 °C. Phase and lattice parameter characterizations, and microstructural and compositional analyses were then carried out using X-ray diraction and SEM/EDX, respectively. The leachates were analysed by Atomic Absorption Spectroscopy (AAS), using which the solute dissolution model for oxides were investigated.

Jan 1, 2014

By Yuanbo Zhang, Zijian Su, Bingbing Liu, Guanghui Li, Tao Jiang

With the depletion of rich manganese ores, high-Fe content manganese ores are becoming the mainstream resources for manganese extraction. Reduction roasting-magnetic separation process is reported as a relatively effective route to realize the separation of manganese and iron. This study investigated the phase transformation of MnO2 and Fe2O3 briquettes (molar ratio 1:1) roasted under various temperatures and CO–CO2 atmospheres. Results showed that when the CO content was in the range of 0–10 vol%, MnxFe3−xO4 (x = 0−1) phase was formed and its content increased with the rising of temperature. The formation of ferromagnetic MnxFe3−xO4 with strong magnetism resulted in an inferior separation of manganese and iron by magnetization roasting-magnetic separation process. With the increase of CO content to over 25 vol%, the MnxFe3−xO4 content decreased while the content of feebly magnetic substance (MnO)y(FeO)1−y(y = 0−1) increased. Further increasing the CO content to over 80 vol%, (MnO)y(FeO)1−y was reduced to MnO and metallic iron.

Mar 1, 2017

By Kenneth N. Han

Ammonia has been found to be an effective leaching reagent for gold, silver and platinum group metals in the presence of appropriate oxidants. Electrochemical and kinetic aspects of the dissolution of elemental gold in ammoniacal solutions have been investigated. The cathodic reaction of aurous di-ammine on the gold cathode has been investigated first. From this investigation, the standard electro-potential of the cathodic reaction .and hence. the Gibbs free energy of formation of the aurous di-ammine were established. The solubility of gold in ammoniacal solutions was also examined in relation to ammonia concentration, temperature and concentration of various oxidants. The anodic reaction of the gold disk in ammonia? in the presence? of various oxidants including oxygen, ozon, hypochlorite, hydrogen peroxide, cupric and cobaltic ammine, and iodine was also examined and the results have been discussed. Excellent dissolution yielding of gold and many other metals, typically better than 95% recovery in 1'-2 'hours of leaching at a temperature ranging 80°C to 190°C has been observed. Test results of the dissolution of gold from elemental state as well as other sources including sulfidic ores and scrap are presented.

Jan 1, 1998

By Shengli Wu, Jiacong Zhang, Mingyin Kou, Bingjie Wen, Heng Zhou

The COREX process, which is considered to be able to replace the blast furnace, still has some gaps to reach the designed productivity. The metallization degree is regarded as one of the limitations of the COREX process. In the present work, several parameters affecting the metallization degree of direct reduced iron (DRI) are analysed by SPSS software (Statistical Product and Service Solution). Melting rate, oxidation degree of reducing gas, oxidation degree of top gas, top gas consumption per ton of burden, temperature of reducing gas, and burden distribution index are con firmed as the main factors affecting metallization degree. Based on this, a linear equation has been developed for predicting metallization degree. Additionally, improving the melter gasi fier vault temperature appropriately, increasing the proportion of high volatile matter coal, and optimizing the type and particle size of iron ore and the pattern of burden distribution have been shown to improve the metallization degree.

Mar 1, 2018

By Hong Li, Chenxiao Li, Wenwen Mao, Hua Lu

Directly charging limestone into slag in BOF is a newly emerging technique which broke through the traditional BOF slagging principle. It is necessary to study the decomposition behavior of limestone in converter slag during BOF steelmaking. FeOx, SiO2, MnOx and pre-melting slags were mixed with limestone according to different quality proportion to simulate the environment of limestone in converter slag. TG-DTA results indicated that slag with individual component, including FeOx, SiO2 and MnOx, all had obvious effects on reducing the decomposition temperature of limestone. Pre-melting slags with multiple components had further reducing effects than individual component. XRD results showed converter slag component would react with decomposition product of CaCO3 and generate solid solution or oxide, reducing the activity of CaO and the decomposition temperature of CaCO3.

Mar 1, 2017

By Moo Eob Choi

A new process for converting sulfur dioxide to elemental sulfur by a cyclic process involving calcium sulfide and calcium sulfate without generating secondary pollutants was developed at the University of Utah. In this process, sulfur dioxide is reacted with calcium sulfide to produce elemental sulfur and calcium sulfate. The latter is reduced by hydrogen to regenerate calcium sulfide. In the present work, the effects of different pelletization conditions for the initial reactant calcium sulfate on the strength and reactivity of the pellets were determined. These conditions include the type, amount, and impregnation method of catalyst, binder amount, and sintering. Experiments were also performed to determine the effects of temperature in the range of 973-1173 K, pellet size, cycle repetition, and water vapor or carbon dioxide content in sulfur dioxide stream on the reaction rates of the cyclic process. Nickel-catalyzed fired pellets produced by the use of molasses or cement as a binder showed good reactivity as well as high compressive strength during the cyclic tests. The binder amount did not significantly affect the reaction rate.

Jan 1, 2006