Search Documents

By E. S. Geskin

"This paper is concerned with the construction of a formal technique for the selection of a metallurgical technology. Exergy consumption is used as the criterion of process efficiency. Different items of the exergy balance are considered and techniques for the reduction of exergy consumption are determined. The selected techniques of exergy saving enable us to identify processes which should be used at different stages of steelmaking. The combination of the selected processes enables us to suggest a technology for conversion of iron ore into steel products. The selection of this technology narrows the range of further search of metallurgical processes. The paper shows that qualitative thermodynamic analysis can be used as the first step in the design of metallurgical processes. IntroductionThe existing processes for making, shaping and treating of steel enable us to convert the available iron bearing ores into marketable steel products. However, the energy cost of metal production is much higher than thermodynamically required, while the metal properties are much lower than thermodynamically available. Increasing cost and declining availability of energy and raw meterials make the creation of new steelmaking technologies imperative. In recent years, the number of novel processes for the making, refining, and shaping of steel have been suggested and tested. Some found a practical application. However, the tested technologies make up a small portion of the physically available routes for the conversion of iron ore into a marketable product. It is also not evident that the optimal routes have been tested and that the selected technologies are the best among those tested.Although the development of new metallurgical technologies must be based on the experimental and practical information, the number of the alternative routes for the making, shaping and treating of steel, as well as the cost of examining each single route, make necessary the use of analytical techniques for the evaluation of the possible ways of process development."

Jan 1, 1988

By Luis M. González, Guzmánm Guillermo D., Davis Juan C.

"The Teniente converter (CT) of the Ventanas Smelter and Refinery of Codelco-Chile has two tuyeres for dry concentrate injection directly into the melt.The diluted phase injection system can feed 15 to 20 kg of concentrate for 1 kg of air, which creates a very abrasive solid/gas phase. The tuyeres commonly used lasted for about 3.5 days due to the accelerated decay of the shell, and 1.5 hours were necessary for the replacement of new ones in the reactor.Tests were carried out with common shell tuyeres with a tungsten based welding cover, and a life span of 28 days was reached, increasing the Teniente converter operational continuity between 1.5 to 2 %."

Jan 1, 2009

By Sergio Neves Monteiro, Fabio Da Costa Garcia Filho, Dian Souza de Oliveira

The properties of the nickel based superalloys, in particular 718 nickel-based alloy, are mainly improved by the hardening mechanism, which is based on precipitation of second phases. This work aimed to compare the evolution of precipitation hardening in a 718 alloy microstructure for two different solubilization conditions: 1050 °C for 2 h and 970 °C for 2 h, followed by a period up to 120 h of aging at 800 °C and correlated to the values of hardness. The microstructure was analyzed by optical microscopy. Vickers hardness test was performed and the grain size was measured. It was verified an increase on the hardeness of this material up to 15 h of aging, after that the value decreased to a level that is maintained until 120 h for both solubilization conditions.

Mar 1, 2018

By Milton Syamujulu

In 2004, KCM Nkana Smelter commissioned a 1200 tonne per day flash dryer and associated dry concentrate transport and injection system on the existing Teniente Modified converter (CT) unit. The aim was to upgrade the existing smelting unit, increase copper output and improve energy efficiency. This paper reviews the design, installation and commissioning phases of the introduction of this new technology and also discusses the initial two years of operating results for both the flash dryer and injection system at Nkana.

Jan 1, 2006

By Bart Blanpain, Muxing Guo, Bin Yang, Fei Wang

An experimental investigation of the precipitation behavior of the Dy2O3 containing slag during cooling was carried out in this work. The slag with composition 45 wt% SiO2—49 wt% CaO—6 wt% Dy2O3 was equilibrated at 1673, 1773 and 1873 K for 24 h in an argon atmosphere, and then quenched in water to determine the phase relations. The composition and microstructure of the equilibrated phases of the systems were determined by EPMA/WDS. The precipitation behavior of the REEs containing phases during cooling was studied by using an in-situ confocal scanning laser microscope (CLSM) observation technique combined with an infrared imaging furnace heating (IIF). Data resulting from this work aims to support further investigation on separation of rare earths from metallurgical slags.

Mar 1, 2018

By Onuralp Yucel, Ahmet Turan, K. Can Candeger

Exothermic riser sleeves are important tools to increase solidification duration, particularly for iron-steel casting. Increasing the time to solidus improved casting product quality by minimizing cavities. Therefore, process costs were significantly reduced. In comparison with the use of unsleeved risers, exothermic riser sleeves retain up to 30–35% of the heat and increase the duration to solidus by nearly 50%. Exothermic riser sleeves are a mixture of metallothermic-based exothermic and insulating materials that are manufactured in different sizes and shapes. Various suppliers produce these sleeves in different compositions. However, the designers must clearly understand the thermochemical and thermophysical properties. The purpose of the present study was to experimentally determine the effects of varying experimental parameters such as reaction duration, flammability and temperature change etc. on selected exothermic sleeves. The results were compared with thermodynamical simulations which were performed using the contents and the corresponding thermophysical properties of exothermic sleeves.

Mar 1, 2018

By Guohua Bai, Mingjun Rao, Jianchen Lim, Guanghui Li, Tao Jiang

"By using thermogravimetry, optical microscope and chemical phase analysis, the solid-state reduction of carbon-burdened chromite pellets in the absence and presence of additives were investigated. The effects of reduction temperature, reduction time and additives on the metallization of chromite pellet were studied. The results indicate that the pre-reduction ratio of carbon-burdened chromite pellets is improved with the increase of reduction temperature and the addition of additives. The metallization of chromium is increased from 63.9% to 92.8% at 1300 °C for 4h with the addition of 2 wt.% of sodium borate. Investigation suggests that the reduction of carbon-burdened chromite pellets is diffusion controlled. The apparent activation energy without additive is 192.1 kJ/mol, while it decreases to 170.4 kJ/mol in the present sodium borate.IntroductionFerrochrome is used to produce high strength, corrosion resistant, wear-resisting, high temperature resistant and oxidation resistant special steels, and it is becoming one of the most important alloy materials for the production of stainless and high alloying ferritic steels [1-5]. Demand for ferrochrome is steadily on the rise due to the growth of stainless steel industry. Nowadays, more than 80% of the world's ferrochrome is utilized in the production of stainless steel [6-7].Ferrochrome is mainly produced in submerged-arc furnaces (SAF) with chromite lump ore. However, lump ore merely accounts for 20% of the chromite ore output, while fine ore (< 8 mm) accounts for about 80% [8]. Therefore, agglomeration of chromite fine ore is necessary before charging into SAF."

Jan 1, 2011

By Anjan Kumari, B. K. Soni, Manis Kumar Jha, A. Vidyadhar, Vinod Kumar

"In the present paper, recovery of valuable metals from the poly-cracked ash obtained by pyrolysis of discarded PCBs has been studied following physical beneficiation and a hydrometallurgical process alternate to smelting. The ash is subjected to comminution for the separation of metallic components from non-metallic fractions by scrubbing, tabling and froth flotation which enriched the metal in the concentrate -97% which was further screened to separate high and low metal concentrate. The finer fraction containing -12% metallic value was leached in acidic solution. Almost all (Cu, Pb, Fe, etc) were leached in 4M HN03 at 90°C in 75 min at a pulp density 100 g/L. The characterization of both ash and residues were made by XRD, EPMA, EDS, etc. to validate the experimental results. The metals from the leach liquor could be recovered/separated using solvent extraction techniques which can further be processed to get pure metal salts/ sheets.IntroductionPrinted circuit boards (PCBs) are an essential component of electrical and electronic equipments (EEEs) as it plays an important role during operation of these devices. The world market of PCBs has reached nearly $60 billion in 2012, with 1.7 percent real growth over 2011 [1]. The diverse technology-driven global market is expected to grow at an average annual rate of 5% by 2014 [2]. The waste EEEs are generated due to replacement of obsolete equipments with modem ones and thus their demand is also increasing rapidly [3]. The discarded e-wastes are being piled up as landfills which affect the environment and cause health threats to living organisms, if not disposed of properly. These e-wastes contain metals some of which are precious, few are hazardous and others as valuable."

Jan 1, 2014

By S. N. Monteiro, J. Alexandre, N. Cerqueira, B. C. Mendes, A. R. G. Azevedo, G. C. Xavier

Brazilian civil construction generates a huge amount of waste in different stages of construction, mainly due to the work methodology used in construction sites. The objective of this work is to study the inclusion of the residual of the civil construction in the sand mass in 0, 10 and 20%, with mortars used to cover masonry. For this study, the beneficiation of the material in crusher was obtained so that it obtained granulometry similar to sand and the most recurrent technological tests in mortars for this purpose, as the mechanical resistance (compression and flexion), water absorption and determination of the coefficient of Capillarity beyond the index of consistency, according to Brazilian norms, that define parameters of execution the technological tests. The results showed that the mortars after the incorporation presented value within the norm except the consistency and capillarity to the 20% that presented problems of fluidity and durability, hindering its use.

Mar 1, 2018

By Jinsheng Wang, Zhixiong You, Xuewei Lv, Yu Zhang, Jie Dang

Electro-titania slag is generally used as the raw material for titanium dioxide production by sulfate process. The phase composition of titanium as well as their disseminated grain size have significant effect on the acidolysis of titanium. Anosovite is considered as the most favorable Ti-bearing phase due to its high acidolysis ef ficiency, while silicates and rutile are not soluble in concentrated sulfuric acid. Different cooling rates will play a significant effect on the phase structure and particle size, which directly affects the acidolysis ratio of titania slag. In this paper, the influence on acidolysis ratio of titania slag at different cooling rates was studied. The results revealed that slower cooling rate resulted in the formation of larger particle size and a comparatively higher acidolysis ratio was obtained. On the contrast, rapid cooling was disadvantageous to the leaching of titanium as the smaller particle size anosovite was wrapped by glass phases.

Mar 1, 2018

By Jeff M. Kuhn

A new solvent extraction process for the removal of halides from zinc sulphate solution was tested in pilot plants at both a 0.1-L/min scale and at a 3-L/min scale. Teck Cominco?s process is called the HalogonTM process, for which patents are pending. Mixer-settlers were used for the 0.1-L/min pilot scale and two BATEMAN pulsed columns for the higher rates. Pilot testing was performed with commercial zinc sulphate solutions containing variable amounts of chloride and fluoride. Sulphate extraction was also controlled and deleterious halides were loaded and stripped into a form suitable for disposal. The engineering aspects and economics of this solvent extraction process for halide removal are also reported.

Jan 1, 2003

By Shadia J. Ikhmayies

In this work the equilibrium temperature-composition phase diagrams of the Si-O2 system were calculated using Thermo-Calc software in the temperature range 500–3000 K. Constituents of stable phases were obtained, and the amounts of certain phases where investigated with the variations in the composition of oxygen and temperature. It is found that quartz with silicon represent a stable phase in the temperature range 500–1150 K, while tridymite with silicon represent a stable phase in the temperature range 1150–1700 K. A liquid phase is found besides tridymite in the temperature range 1700–1750 K, and a stable phase of cristobalite with liquid appears in the temperature range 1750–2000. The maximum amounts of quartz, tridymite, and cristobalite are found at oxygen mole percent of 67.7%.

Mar 1, 2017

By De-qing Zhu, Zi-fu Gao, Jian Pan

"In order to produce high quality metalized products and prevent from burden cohesion during pre-reduction, self-fluxed pellets were made for COREX process in the paper. The effects of reduction temperature and reducing gas composition on pre-reduction behaviors of self-fluxed pellets are studied. The results show that the prereduced pellets have poor quality and deposited carbon appears when the reduction temperature is between 600°C and 700°C. The metallization rate, reduction degree and compressive strength of prereduced pellets are promoted by the elevating reduction temperature and mole fraction of H2. Pellets reduced by pure H2 at 800°C have high metallization rate (96.2%), reduction degree (99.4%) and compressive strength (960N/pellet). In all tests, self-fluxed pellets display normal swelling (RSI<l5%) behavior which reveals that self-fluxed pellets are suitable for COREX process. Increasing reduction temperature and mole fraction ofH2 in reducing gas is benefit for pre-reduction of pellets.IntroductionCompared with Blast Furnace, the COREX process has advantages of short flow sheet, using non-coke coal and high-energy utilization. Acidic pellets and lump ores are the chief iron- bearing burden for COREX process which could lead to low melting point substance appearing in per-reduction process. In addition, the acidic hematite pellets tend to swell during the reduction [1-3]. This will result in decreasing compressive strength of pellets, burden cohesion, bad air permeability and poor work status in shaft furnace. Adding carbonate flux could restrain burden bonding to some extent in actual production, but decomposition of carbonate flux increases energy consumption. Worse still, weak reduction potential is unfavorable to iron material reduction [ 4, 5]."

Jan 1, 2013

By Xiaoming Huaa

The effect of the anodic polarization on the composition and morphology of the surface layer formed on chalcopyrite during ammonia–ammonium chloride leaching was investigated. The anodic polarization on the chalcopyrite electrode was used for oxidation and dissolution of chalcopyrite, and the resulting oxidized layers were characterized by XPS, SEM and optical microscopy. The results show that oxide layers exist on the chalcopyrite surface with or without any anodic polarization in the leaching solution at ambient atmosphere. However, the composition and morphology of the layers are strongly depended on the extent of polarization. The distribution of FeOOH and Fe2O3 within the oxidized layer was inhomogeneous for the sample at the open circuit potential (OCP). The composition and morphology of the oxidized layers which were formed at anodic potentials lower than 0.3 V versus SCE were similar to those of the chalcopyrite at the OCP. At anodic potentials above 0.4 V, the oxidized layers contained many cracks, and they were fragile and exfoliated. Furthermore, the sulfide had been oxidized to sulfur species with higher oxidation states. The oxidation of the chalcopyrite seemed to undergo a cyclically oxidative process that suggested growth and spallation of oxidation layers on chalcopyrite in a layer-by-layer sequence.

By D. C. Austin, P. J. Hazell, A. A. H. Ameri, J. P. Escobedo-Diaz, D. East, M. A. Bevan, A. D. Brown

Additive Manufacturing (AM) has become increasingly popular due to the ability to produce components with complex geometries and properties. The efficiency of this manufacturing method is investigated in this paper by examining the mechanical performance of AM austenitic stainless steel 316L under different strain rates. Dynamic compression experiments were conducted by using a Split Hopkinson Pressure Bar (SHPB). Microstructural observations were performed by utilizing optical microscopy. The behavior of this material is compared against stainless steel 316L manufactured by conventional methods. The results show that theAM316L used in this study display a considerable difference in the mechanical properties compared with conventional stainless steel alloys.

Mar 1, 2017

By Mikio Kobayashi

Extraction of valuable metals from sulfide ores continues to be a very important, process and so the strict control of discharge of harmful metals in effluents from refineries becomes more important in the future. The recovery methods for heavy metals have been developed. Some metals such as Se and As are still difficult to be removed to very low concentration, although the techniques for recovery and removal for many kinds of heavy metals have already been developed. Especially, in case of Se the recovery system from water with low concentration has not be developed yet, although the WHO decided Se to be harmful for human beings and then the discharge control is under obligation now. In general Se exists as selenite ion and/or selenate ion in aqueous phase and selenite ion is able to be recovered by coprecipitation with ferric hydroxide or by reduction to solid selenium by general reductants. Selenate ion, however, has a strong resistance to conventional treatments. Therefore the new technique for the recovery of Se from water including selenate ion has to be developed. In this presentation the new approach for removal of selenate ion using the reaction in which ferrous ion is oxidized to ferric ion is presented. Selenate ion is reduced to selenite ion during the reaction and then to solid selenium, while ferrous ion is oxidized to ferric ion. The coexistence of activated carbon is very useful to increase the reaction rate. The use of iron powder is also effective and very useful for reducing gel-like precipitates mainly consisted of ferric hydroxide. The concentration of the residual selenate ion is probably under 0.1 ppm after recovering Se by the mentioned-above approach. In addition to the mechanisms of these reactions, the effects of pH, coexistent positive and negative ions, and reaction temperature are also presented. Furthermore the investigation of the behavior of selenosulfate is presented.

Jan 1, 1998

By Fernanda de Paula, Lázaro A. Rohen, Sérgio N. Monteiro, Rafael G. de Castro, Carlos Maurício. F. V, Maycon A. Gomes, Frederico M. Margem, Anna C. C. Neves

Synthetic fiber has been gradually replaced by natural fiber, such as lignocellulosic fiber. In comparison with synthetic fiber, natural fiber has shown economic and environmental advantages. The natural fiber presents interfacial characteristics with polymeric matrices that favor a high impact energy absorption by the composite structure. However, until now little has been evaluated about the hemp fiber incorporated in polymeric matrices. This study has the purpose of evaluate the impact resistance of this kind of epoxy matrix composite reinforced with different percentages of hemp fibers. The impact resistance has substantially increased the relative amount of hemp fiber incorporated as reinforcement in the composite. This performance was associated with the difficulty of rupture imposed by the fibers resulting from the interaction of hemp fiber / epoxy matrix that helps absorb the impact energy.

Jan 1, 2015

By Ping Long, Bin Yang, Jian Wu, Xiumin Chen, Wenli Zhang

In this study, the analysis method of trace element in pure indium using glow discharge mass spectrometry (GD-MS) has been established by correcting the analysis result, which was obtained from non-standard quantitative method of GD-MS. The effect of instrument operating parameters, the resolution and isotopes and the pre-sputtering time on the determination results were investigated respectively. The optimized operating parameters of the instrument were obtained as follows: the discharge current was 37.5mA and discharge airflow was 475ml/min. Mass spectral interferences have been eliminated using selected resolution and isotope. The pre-sputtering time was 30 min. 4 trace elements in two pure samples were determined for 6 times. The RSD were less than 20%. The content of trace elements in indium samples was determined by GD-MS and Chemical Analysis Method of Indium which is tested by inductively coupled plasma atomic emission spectrometry, respectively. The results were consistent with each other.

Jan 1, 2016

By Ian Buterbaugh, Calvin Lo, Tomoko Sano, Brendan Koch, James Catalano, Timothy Walter

In this research, two grades of alumina, one at nominally 85% composition and the other at 99.5% were characterized. Microstructural and phase characterization was conducted using Scanning Electron Microscopy, Energy Dispersive Spectroscopy, X-ray Diffraction, and micro-computed X-ray tomography. It was determined that the Knoop hardness values were influenced by the porosity in the 85% composition. Quasi-static compressive tests and high strain rate compression experiments were conducted to determine the influence of the microstructure to the compressive properties. It was observed that the overall compressive strengths increased with strain rate. Although the Knoop hardness values were much lower in the 85% alumina due to the porosity, the compressive strength at both quasi-static and dynamic strain rates were not significantl lower than those of the 99.5% composition.

Mar 1, 2018

By M. E. Myers

An experimental program is being carried out to determine the thermodynamic characteristics of zinc solubilization in high-temperature iron and iron-carbon alloys. Two versions of an isopiestic technique are being used, with zinc at a lower temperature being equilibrated with pure iron foils or molten iron-carbon alloys at a higher one. The lower temperature sets the partial pressure of zinc vapor, and thus the activity relative to a given reference state. Initial results show Henrian behavior for dilute zinc solutions in austenite and a molten 4.6% C alloy, with unit-pressure solubilities in pure Fe that closely match the predictions of Wriedt.

Jan 1, 1992