Search Documents

By P. Chris Pistorius

"Use of coke in blast furnace ironmaking is the main origin of carbon dioxide emissions from integrated steelmaking. Use of pre-reduced iron feedstocks would reduce the coke rate and, if pre-reduction were carried out with natural gas, would decrease the overall carbon intensity of ironmaking. Blast furnace productivity would also increase, because the blast volume per unit of hot metal would decrease. This paper shows that these trends can be predicted quantitatively, by using a conceptually simple Rist-style blast furnace mass and energy balance, assuming furnace productivity to be limited by the tuyere gas flow rate. Such predictions would assist in optimizing the choice of the degree of reduction and relative amount of pre-reduced blast furnace feed.IntroductionSteelmaking is responsible for some 5% of world CO2 emissions, at a rate of approximately 1.9 tonnes of CO2 per tonne of cast steel [1]. In integrated steelmaking, the ultimate source of most of the CO2 emissions is coke, the indispensible (and expensive) fuel and reductant for blast furnaces. There are several research programs underway worldwide which seek to lower the carbon intensity of ironmaking; one of the largest is the European ULCOS program [2], in which the main proposed change to blast furnace ironmaking is to scrub CO2 from the furnace off-gas (for possible sequestration), recycling the remaining gas to the furnace. To limit the recycling nitrogen load, oxygen rather than air is used to combust coke.A conceptually simpler approach is to charge prereduced feed (direct-reduced iron) to the blast furnace. This approach has been used for some two decades at the AK Steel Middletown plant, where some 200 kg of direct-reduced iron (DRI) is charged per tonne of hot metal [3]. The Middletown blast furnace has exceptionally high productivity (rate of iron production relative to the furnace hearth area), simply because less coke is required per ton of hot metal if part of the feed is already metallic. Midrex [4] has provided some quantitative predictions of the implications of DRI use in the blast furnace, stating that for every 10% of Fe in the feedstock that is in metallic form, the fuel requirement decreases by 7% and the productivity increases by 8%."

Jan 1, 2012

By Akita Ito, Sumio Kato, Mikio Sugai, Shinichi Nakata

"Spark Plasma Sintering (SPS) is a newly developed method for the sintering of metal and ceramic powders, and completes their densification at low temperature and in short period. The SiC powder was synthesized from diatomite and graphite or carbon black by heating at 1 450°C for 1 hr in an argon atmosphere. The synthesized SiC powder was heated at 1500-1800°C, 50 MPa for 15-18 min by SPS. The relative density of sintered SiC body increased with the rise in the temperature. The oxidation of the surface of the SiC particle and impurities in SiC from diatomite greatly influenced the sintering promotion of SPS.IntroductionThe SiC has high hardness because of the covalent bonding, and is also excellent in thermal and chemical stability. However, it is difficult to obtain a dense SiC sintered body by the combustion heating-method. Therefore, the dense SiC bodies have been made by the use of additives and I or the hot pressing (HP) method.In this study, the SiC powder was synthesized by using diatomite of natural products and graphite, and carbon black of reagent as raw materials, and the relationship between the properties of SiC powders prepared at various synthetic conditions and the density of sintered body by SPS was examined."

Jan 1, 2000

By Geir Wedde, Anders Sorhuus

"Vast quantities of energy are released as heat to the environment from industrial operations. Many countries target waste heat recovery to mitigate CO2 emission. Exhaust gases from industries such as primary aluminium smelting, carry a substantial portion of the waste heat generated. For a cost efficient capture of more valuable heat (higher exergy), heat exchangers should operate on the exhaust gases upstream of the gas treatment plants. Heat exchange surface would be exposed to dust laden gases with risk of fouling. Heat exchangers of innovated design and operation have overcome the potential of excessive fouling rates. Heat exchangers of the ""shell and tube"" design have been demonstrated for exhaust gases from ferroalloy as well as primary aluminium smelters. In addition to the heat recovery, gas cooling results in smaller gas treatment plants with lower costs and reduced emission. The aluminium experience is exampled in the paper.IntroductionIndustrial usage of energy continues to grow as a result of increasing volumes of production, a trend that is likely to continue in the coming decades as living standards keep rising globally. World energy consumption (Figure la) is to grow 49 % by 2035 (ref. 2010) as reported by EIA [1]. The industrial sector consumes somewhat more than 50% of the total world energy consumption predominantly the energy increased demand comes from non-OECD countries in Asia. The industrial consumption by production of metals iron and steel accounts for 14 % and for non-ferrous metals 3 % mostly for aluminium production (Figure lb). Aluminium production will be discussed in this paper as an example of an industry with large quantities of waste heat to recover"

Jan 1, 2012

By David G. C. Robertson

A new approach is described for the calculation of the kinetics of metal/slag, metal/slag/gas, and metal/matte/slag/gas reactions. The algorithm assumes that equilibrium is achieved at the interface between phases, and uses an equilibrium solver (such as SOLGASMIX) to compute the equilibrium state at the interface at each time step during the reaction. For multiple phase systems a number of unit operations, representing the different phases and interfaces, must be connected together in a reasonalbly complex manner, and the METSIM software package has been utilized for this purpose. The new approach is superior to the SMAK software developed by the author and his co-workers over the past decade, for the reasons discussed in this paper.

Jan 1, 1995

By Baokuan Li, Fang Wang, Meilong Shan

"As the advantage of uniform bus loading, the electroslag remelting (ESR) furnaces with three - phase installation by delta or star connection are mainly used to produce the large or super large ingot. The electrical efficiency is significantly improved as the short circuiting through the molten slag. However, little is found about fiindamental research on the electromagnetic field of the ESR system with three -phase installation. A three-dimensional (3D) finite element model was developed to simulate the current density, magnetic field, electromagnetic force and Joule heating for a system of electrode, slag and ingot in the ESR system with three -phase installation.IntroductionThe metallurgical performance of the ingot is the fundament and precondition to obtain the large forging of high quality, which has a critical role in the producing of forging. The electroslag process (ESR) to product the metal materials of high homogenization and clarity become more and more popular[1].The electroslag process is a special smelting technology of producing small ingots, which originate in 1950[2].At present the three, four or six electrode is used in large scale electroslag furnace. It has been found that the deeper molten pool and the wider of the two-phase zone with only one large diameter of electrode to product large ingot effect the solidification microstructure of ingot[3]. However, the molten pool becomes shallow relatively with several electrodes producing the large ingot, which is benefit to the solidification microstructure of ingot. Three electrodes electroslag remelting furnace take the three phase equilibrium power supply to making the load and electric power network balance, avoiding the distortion phenomenon induced by single phase power supply and saving electric power. It also can uniformize the distribution of heat source."

Jan 1, 2012

By P. V. Ananthapadmanabhan

Feedstock powders of metals, alloys and ceramics for thermal spray applications have to meet several specifications. Particle shape, size and distribution, powder flow characteristics and density are the important factors that need to be controlled, in order to ensure high spray efficiency and better coating properties. Thermal plasma technology can be effectively utilized to produce metal, alloy and ceramic powders for spray applications. The present paper describes plasma spheroidisation of commercially available aluminium powder and nickel-aluminium powder blend in a plasma reactor. Results show that the processed powder particles bear spherical morphology with excellent flow characteristics, which make them ideal for thermal spray applications.

Jan 1, 1997

By Min-Min Lin, Bing Xie, Hong-Yi Li, Yang Yang

After precipitation of ammonium vanadates from vanadium-containing leaching liquor, vanadium (V(V)) and chromium (Cr(VI)) exist in the waste water in form of vanadate ions and chromate ions. In order to efficiently extract and recover V(V) and Cr(VI) from waste water, an environment-friendly method based on anion exchange was investigated in batch tests using macroporous weak base resin Dex-V. The adsorption conditions optimizes in detail, including the effect of pH, initial metal concentration, resin volume, contact time and temperature. The ion-exchange adsorption process for both V(V) and Cr(VI) showed maximum capacity at pH 3.0 for an initial concentration of 100 mg L−1, and reached equilibrium after about 40 min of contact at 298 K. The maximum adsorption ratio under the optimum conditions for V(V) and Cr(VI) was 98.98 and 99.87%, respectively. Result shows that the established method is a promising alternative for simultaneous extraction of vanadium and chromium.

Mar 1, 2018

By Osamu Yamamoto

In antibacterial evaluation of carbon-ceramic composites, we prepared two type composites with emphasis on carbon-ZnO system; one was porous carbon materials containing ZnO nano-particles and another was porous ZnO coated with carbon thin film. Porous carbon samples containing ZnO at highly dispersed state were prepared by carbonizing the resin exchanged by Zn2+ ion. Porous ZnO coated with carbon thin film was obtained by the pyrolysis of poly (vinyl alcohol). Antibacterial activity of these composites obtained was evaluated by measuring the changes in electrical conductivity with bacteria growth. The antibacterial activity on the composites increased with the increase of t he amount of ZnO in composite and decreased with the increase of carbonization temperature. The antibacterial activity for Staphylococcus aureuswas found to be stronger than that for Escherichia coli. No activity of the carbon samples without ZnO was observed. The occurrence of antibacterial activity was supposed to be due to the generation of hydrogen peroxide from ZnO in composite. In the present work, antibacterial activity of carbon-ZnO composites was studied in the details.

Jan 1, 2006

By Xiangru Chen, Qijie Zhai, Wei Zhang, Haicheng Li, Chao Yang

In this paper, ductile iron material with different content of niobium was prepared by a scientific melting method. Image Analysis Software was used to studied the effect of niobium microalloying on both pearlite content and pearlite lamellar spacing in ductile iron quantitatively. The results showed that the addition of a small amount of niobium could increase the pearlite content and decrease pearlite lamellar spacing of ductile iron effectively.

Jan 1, 2015

By Kunio Nakahara, Kashiwagim Junichi, Takao Hayashi

"There are many problems for electronic devices and parts which were caused electrostatic damage by static electricity. It is necessary for prevention of electrostatic charge to decrease surface resistivity of material using electroconductive coating. Mitsui Mining & Smelting Co., Ltd. developed metal oxide type electroconductive pigment PASSTRAN (trade mark) Type-IV which is barium sulfate coated with SnOz(Sb) thin electroconductive layer. This paper shows about pigment characteristics and film condition of antistatic transparency paint which contained PASS TRAN.L.IntroductionRecently rapid development of electronics technology diffused electronic devices and products to Office, Factory, Laboratory and our life. But the other side, there are many problems for electronics parts which were caused electrostatic damage under static electricity. Demand of antistatic materials were become lager by this situation.There is close relationship between surface resistivity of material and static electricity. If the surface resistivity of object is enough low (under 109 Q /Sq), static electricity is dissipated quickly. So it is necessary for prevention of electrostatic charge to decrease surface resistivity of material using electroconductive coating.1) There are many type of electroconductive materials, for example, carbon black, metal powder, electroconductive polymer and so on. Especially, carbon black is used for general purpose by reason of its low cost, but it has big problem of black color. It can not get any color without black, and it caused contamination of carbon.In recent years, metal oxide electroconductive pigment (ECP) was developed and used for special purpose which demands transparent coating or easy dispersion to make ECP paint or endurance under hard environment and so on. Mitsui Mining & Smelting Co., Ltd. developed electroconductive pigment PASSTRAN Type-IV which is BaS04 coated with electro-conductive Tin oxide layer."

Jan 1, 1998

By Shubin Wang

Copper(II) and nickel(II) are often recovered from ammoniacal alkaline solutions by solvent extraction using hydroxyoxime extractants: both copper(II) and nickel(II) are extracted from ammoniacal alkaline solutions and, from the loaded organic phase, nickel(II) is selectively stripped with a dilute acid followed by copper(II) stripping with an acid of higher concentration. Since a small portion of ammonia is co-extracted with copper and nickel, the extracted ammonia should be scrubbed using a dilute acid before metal stripping. In the present study, a mechanistic model has been developed in order to support design and control of this process. The equilibrium distribution ratios of copper(II), nickel(II), and ammonia at 298 K using LIX® 84-I (active component, 2-hydroxy-5-nonylacetophenone oxime) as the extractant are successfully correlated by considering the relevant equilibria. Based on these results, quantitative prediction of equilibrium distribution ratios in the process has been made possible, and suitable conditions for the efficient separation of copper(II) and nickel(II) are discussed.

By Qin Hua, Xiangru Chen, Qijie Zhai, Yongsheng Yan, Liang Chang

"In this paper, pure bainite ductile iron and their alloying form of 0.2wt% niobium were prepared by a controlled cooling heat-treatment. The effect of niobium alloying on the microstructure, hardness and impact toughness of bainite ductile iron was studied. The results show that adding niobium effectively improves the hardness and toughness of bainite ductile iron. The hardness and the impact toughness of niobium-alloyed bainite ductile iron were investigated by varying the temperature at which samples were fed to the incubator.IntroductionThere are two essential methods to prepare the bainite ductile iron: isothermal quenching [I-31, and alloying [4• 51• Isothermal quenching process is very time and energy consumable, concerned as a high cost technique for mass production. Besides, there are certain limitations on the size and shape of castings in this process. In addition, it potentially harms the environment. As for the alloying, Ni, Mo, and Cu have to be utilized to obtain bainite. However, the large demand and high cost of Ni makes it not feasible in practice.It is well known that niobium can promote the formation of carbon compound, and improves the stability ofundercooled austenite, which is preferred to the increase of the hardenability. Previous studies showed that niobium could refine the grain and improve the mechanical properties of gray cast iron [6-81 • Therefore, in the present work, the effects of niobium and the temperature at which samples were fed to the incubator on the microstructures and properties of niobium alloyed bainite ductile iron were investigated."

Jan 1, 2014

By René Bustamante

A GPSS/H simulation is beeing done for a traditional smelter of copper, which envolves a reberberatory furnace, a set of Peirce Smith converters (PSC) and a refining furnace. The objective is to try different plant layouts, being the handling of liquid material at high temperature one the mainly concern, this envolves a study of the ladles and cranes used. Some of the modifications that can be evaluated through the model is the role of oxygen potential when tonnage oxygen is used, number of cranes, PSCs in operation, etc.

Jan 1, 1992

By David Roha, Øyvind Mikkelsen

"Significant resources have been spent throughout the years in the investigation of production of aluminum by carbothermic reduction. Due to the technological challenges involved, the efforts have not yet resulted in a commercial process. An initiative to overcome issues that prevented previous attempts to succeed was taken by Alcoa through the Advanced Reactor Process. The research program has resulted in technical developments which have resolved many of the previous issues. The knowledge about the process has continuously improved through physical and computer modeling as well as by experimentation at various scales. The technical achievements together with improved process understanding have resulted in a reactor design able to continuously operate the process for several weeks at the time, with hundreds of kilograms of alloy in every tap.IntroductionThe Hall-Heroult process has since its invention in the late 19th century, been essentially the only process used for commercial production of primary aluminum. The process has so far proved to be superior to all potential process alternatives and has continuously been improved. Although the Hall-Heroult is a reliable process it also has challenges:"

Jan 1, 2012

By Zhou Aiping, Lv Guozhi, Niu Liping, Wang Wenbo, Zhang Ting’an, Jiang Xiaoli

The current method used to produce sponge titanium utilizes a process cycle of magnesium metal and chlorine gas via the electrolysis of magnesium chloride. The primary issues are the high capital cost of the electrolysis process and the environmental regulations limiting high chloride concentrations. Thus, the authors have developed a conceptual method involving theelectrolysis of magnesium chloride as well as a reduction process which allows for a cycle of magnesium and chloride. In the new method, MgCl2 which was distilled during the titanium extracting process as raw material was directly pyrolyzed at elevated temperatures yielding high purity magnesium oxide and chlorine. The resulting magnesium oxide can be used in the production of magnesium metal. This work examines and compares the energy consumption and economic benefits of the Kroll method as well as the new proposed method. The results from the study demonstrated that in comparison to the traditional Kroll method, the new method provided considerable economic and environmental benefits.

Jan 1, 2014

By J. Shibata

The recovery process of valuable metals, such as Ll, Mn, Ni and Cr from a waste lithium battery was developed n this study. Lithium and Mn are selectively leached from the battery by using dilute mineral acid. Main part of the battery comprises stainless steel, and Fe, Ni and Cr are easily leached by the mixture of dilute HCl and HNO3 Lithium and Mn are precipitated as metal carbonates from the? individual leached solution with sodium carbonate solution. The solution containing Fe,Ni and Cr Is treated by solvent extraction to separate NI and Cr from the leached solution. The experiments are carried out for leaching and separation steps. According to the experimental results, the flow. sheet for a recovery process of valuable metals from a waste lithium battery has been established.

Jan 1, 1995

By Tatiana Pereira Moreno, Priscilla Aki Mori de Hanashiro, Viviane Tavares de Moraes, Denise Crocce Romano Espinosa, Hugo Hashimoto

"Nowadays, End-of-Life (EoL) Liquid Crystal Displays (LCDs) are traditionally disposed in landfills. The increasing access to LCD technology over the last years by Brazilian consumers has intensified LCD' s disposal as an environmental and economic issue. This study aims to characterize used LCDs to identify the main components for recycling. Characterization was performed through scrap disassembly and its components were identified, separated, and weighted. LCDs were disassembled and the following divisions were applied: screen, metal frame, polymeric frame, polymeric sheets and electronic part. Some techniques were used to determine the concentration of Indium in the LCD, the glass/plastic ratio and the different kinds of polymers that compose the screen. The techniques used for characterization included inductively coupled plasma optical emission spectrometry (ICP-OES), Fourier transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA). This method, when applied to a wide range of LCDs, can allow the development or improvement of an EoL management of LCD.IntroductionWaste Electrical Electronic Equipments (WEEEs) are waste from discarded equipment, such as computers, monitors and cellphones [1]. Over the past years, treatment of WEEE has been emphasized. It occurs due to the technology's advancement that leads to an even larger increase of WEEES [2].Among WEEEs, there are the liquid crystal displays (LCD). LCD technology is applied in cell phones, tablets, computers and monitors. Nowadays, it's the most well known technology when it refers to monitors, due to its advantages over the Cathode Ray Tube (CRT) technology. Some of them are energy saving, smaller size and no radiation emission [3].This feature in the LCD's global market along with the speed at which electronic equipment becomes obsolete affects society economically and ambiently.This issue becomes even more serious when considering the final destination of the liquid crystal displays. LCDs are lead to landfills as other WEEEs. Besides the different materials long degradation time, the environment is damaged by the disposal of the potentially reusable and hazardous materials [ 4]."

Jan 1, 2014

By Fathi Habashi

Laboratory autoclaves for hydrometallurgical investigations are available in a variety of sizes, models, and materials of constructions. They vary in sizes from 25 mL to 2 liters for laboratory studies and 5 to 50 gallons for pilot plant work. They are essential tools for studying aqueous oxidation of sulfide concentrates, dissolution of oxide minerals at high temperature and pressure and hydrothermal precipitation reactions. The maximum pressure and temperature at which any pressure vessel can be used will depend upon the design of the vessel and the materials used in its construction. Since all materials lose strength at elevated temperatures, any pressure rating must be stated in terms of the temperature at which it applies. A review of existing models and their accessories will be given.

Jan 1, 2000

By E. M. Timoshenko

Autoclave technology can be effectively used for liberation of complex mineral raw materials to transfer valuable constituents into solution for their subsequent recovery or to refine feed material in order to remove deleterious impurities, e.g. arsenic. The high efficiency of autoclave processes is attributed to the fact that they are suitable for processing of refractory raw materials, have low capital costs, high productivity, ensure integrated utilization of the feed materials, produce innovative saleable products, completely eliminate any air emissions, provide low-waste or waste-less technology, mechanization and automation of production processes. In the immediate future, it might be expected that autoclave processes will find use on commercial scale for production of heavy non-ferrous metals in combination with other processes (hydrometallurgical, upgrading, sorption and solvent extraction, electrolytic, etc.) to ensure: - Integrated processing of refractory ores and concentrates (pyrrhotite, zinc, copper-zinc, lead-zinc, nickel-cobalt, copper, pyrite); - Production of metallic powders of base metals as commercial products (copper, cobalt, nickel, etc.), composites on their bases, final products and saleable salts. Processing technologies incorporating autoclave processes, especially at the stage of liberation (chemical upgrading) of raw materials are characterized generally by high overall recoveries of valuable constituents significantly exceeding recoveries common for conventional pyrometallurgical processes (for some elements by several tens of percent).

Jan 1, 2006

By Y. C. Avniel, T. E. Warner

"It is important to be able to measure sulphur and nitrogen in molten iron and steel on-line. Unfortunately, there are no solid electrolytes which are stable under oxidising conditions and in which the ions of these species are mobile. In this paper, novel applications of beta alumina electrolytes are described and the results compared with data in the literature. Excellent agreement was obtained confirming this approach as a viable method of detecting elements whose ions are not mobile in solid electrolytes.IntroductionIn the past two decades, the rate of many processes in steelmaking have increased substantially. The sophistication of chemical analysis has also increased but analytical equipment is frequently positioned a significant distance from the operating plant which dictates that time is spent taking a sample, sending it to the analytical facility, preparation of the analytical sample prior to insertion into the equipment. In many cases, the time taken for analysis can exceed the time taken for the actual process and is now the rate defining step. Furthermore, most analytical methods are unable to distinguish between the amount of element which is dissolved in the steel and that contained in precipitates. Even if the analytical equipment could separate these two, the distribution would have changed between the molten steel and the cast sample. It would be an advantage to analyse on-line for impurities in molten metals."

Jan 1, 1997