Search Documents

By Naiyi Li, Henry Hu, Alfred Yu

"In the past few years, various squeeze cast aluminum components have been developed and successfully implemented in various vehicles by the automotive industry because of their superior engineering performance. However, fundamental understanding of the formation of air gap during squeeze casting processes is still very limited despite of its significant influence on the extent of heat transfer between the casting and mould. In this paper, a mathematical model has been developed to simulate phenomena of air gap between the casting and mold' during squeeze casting of aluminum alloys. The model considers the effect of process parameters such as applied pressures and mold temperatures on the events of air gap formation. The predication indicates that the occurrence of highly enhanced heat transfer in squeeze casting of aluminum alloys primarily results from the presence of excess applied pressures.IntroductionA number of squeeze cast Al components has been developed and used in mass-produced vehicles in the past few years, such as steering knuckles, Road wheel, Engine Block etc. This is attributed to their superior engineering performance. In squeeze casting, the cooling rate can be increased by applying high pressure during solidification which results in the noted refinement in the micro structure scale leading to better casting properties. However, the excessive pressure increased interfacial heat transfer coefficient is affected during the solidification by air gap formation and die surface condition etc., which is believed to increase thermal resistance at the casting/die interface [l - 4]."

Jan 1, 2004

By Marcos V. F. Fonseca, Gilson V. Fernandes, Caroline G. de Oliveira, Sergio N. Monteiro, Frederico M. Margem, Anna C. C. Neves

Natural fibers represent an economic and environmental motivation for replacing the synthetic fibers, mainly as composite reinforcement material, which is one of their major applications. Some advantages of the natural fibers are the biodegradability, low cost and renewability. Among the natural fibers, the lignocellulosic ones are highlighted for their high resistance. One of the most cultivated lignocellulosic fibers in Brazil is the Eucalyptus fiber, extracted from the bark of Eucalyptus citriodora plant. In this work, it was investigated the tensile behavior of the epoxy matrix composites reinforced with different volume fractions of Eucalyptus fibers. The specimens were made by pouring the still liquid resin into the mold and laying the fibers onto the resin. The results show a decrease in the tensile resistance with the increase of volume fraction. It is due to the low adhesion between the fibers and the matrix.

Mar 1, 2017

By Benjamin Kohler, Amelinda Olson, Marc Snyderman, Chanaka De Alwis, Mike Lewis, James Cox, Matthew Call, Julia Kluck

UTRS Inc. has developed a novel two-step method to extract commercially viable titanium alloys (patent pending no. 20130164167[1]). This approach has proven its potential to produce a variety of titanium alloys (Ti-6Al-4V,Ti Al ,etc.,) x y and has demonstrated a number of advantages over the current commercial titanium production process. Additionally, the UTRS Process operates without producing CO2 and eliminates the use of TiCl. Step 1: Aluminothermic reduction makes available many types of ores that could otherwise not be used. Due to the aluminothermic reduction technique and the composition of the ore,metal extracted from this step will inherently contain non-titanium elements. Step 2: Electro-refining removes undesirable elements from the thermally extracted titanium. This refined metal has a dendritic morphology with a wool-like appearance that is referred to as “titanium wool”. This new morphology of titanium allows it to have a diversity of endproduct types from titanium powder to bulk titanium.

Mar 1, 2017

By Shangshu Li, Xin Li, Xionggang Lu, Xingli Zou, Kai Zheng, Yinshuai Wang

Ti5Si3/TiC composite has been successfully prepared from the titanium-rich slag/SiO2/C mixtures precursors by an electrochemical process. The electrochemical production process was carried out in molten CaCl2 salt at 1000 °C and 3.8 V. A pressed cylindrical pellet of titanium-rich slag/SiO2/C mixtures served as a cathode, and a solid oxide oxygen-ion-conducting membrane (SOM) tube filled with carbon-saturated liquid tin acted as an anode. The phase transformation of the cathode pellets during electrolysis process was investigated, the microstructure of the obtained products was characterized. It is found that the reaction pathways can be divided into three main stages during the electro-reduction process. The first stage is the generation of calcium compound, the second stage is the electrochemical reduction of the compound, and the third stage is the formation of Ti5Si3/TiC composite. The prepared Ti5Si3/TiC composite exhibits homogenous and nodular particle morphology.

Mar 1, 2018

By J. R. Hartin

Traditionally, many of the advances in casting technology have been made by expensive and time consuming trial-and-error methodology. Modeling of the complex solidification process promises production of castings which are made "right the first time." Even though several models are available for simulation of conventional casting processes, none of them address this relatively new technology of investment cast titanium aluminides. In this paper, modification and application of a transient, three-dimensional, fully coupled fluid flow and heat transfer solidification modeling computer program to the analysis of centrifugally cast titanium aluminides is discussed. The predictive results of the program are compared to qualities of actual cast parts for validation.

Jan 1, 1992

By Leonardo Mota, Lucas L. da Costa, Milton B. Filho, Sergio N. Monteiro, Helion Vargas, Tammy G. R. Portela da Silva

"A natural biofoam extracted from the buriti palm tree has shown characteristics for potential substitution of synthetic foams. In the present work, a photoacoustic thermal characterization was performed on buriti biofoam samples. An open photoacoustic cell technique and a photothermal rise method performed under continuous laser illumination were employed in order to determine the thermal diffusivity and the specific heat capacity of such material. In addition to their intrinsic values (finger print), these physical parameters represent the light-into-heat conversion efficiency and the amount of heat stored per unit volume, respectively. The results showed that the buriti biofoam presents thermal properties that permit its use as an effective insulation material.IntroductionSolid foams are very light materials with increasing engineering applications [1]. A natural biofoam obtained from the petiole of the buriti palm tree (Mauritia flexuosa) has been recently investigated [2-4]. The evaluation of the buriti biofoam properties and the characterization of its microstructural aspects have shown that this biofoam has a potential as a new engineering material with very low density. Additionally, its reduced open porosity and low absorbed humidity revealed a promising material for packing and floating applications. In fact, this buriti biofoam, extracted from the palm tree natural of the north region of Brazil, is being used by the low income population as a modest substitute for Styrofoam® [1].As a potential insulating material, the buriti foam needs to be characterized in terms of its thermal and acoustic properties. A preliminary investigation [3] on the thermal behavior of this natural biofoam by thermogravimetric analysis, TGA, and its derivative, DTG, as well as differential scanning calorimetry, DSC, revealed parametric conditions associated with water loss and structural decomposition. Both the surface humidity and the release of hydration water were determined. Different decomposition events were attributed to both, more rigid as well as to more flexible molecular segments. Table 1 depicts technical data obtained so far for the buriti biofoam. These data are compared to those corresponding to Styrofoam®."

Jan 1, 2011

By Larry M. Southwick

The smelting of copper and other non-ferrous metals have made considerable advances over the last 125 years. Many of the ideas and processes currently in use were attempted early in the history of smelting and were unsuccessful. Often the cause was incomplete understanding of the metallurgy involved, inadequate refractories, poor materials of equipment fabrication or trying too many new ideas at once. With time, these problems get solved and the technologies become commercialized .These were processes whose time had not come when originally proposed, but did eventually. On the other hand, there have been some concepts whose time will never come. They were impossible then and they are impossible now. The people that dream these up were either crackpots (they didn't know what they were doing, but thought they did), or charlatans (they knew they didn't know what they were doing, but didn't care). Both rely on bad science to propose metallurgical absurdities. These too have their place in the development of technology, though mostly negative, and several examples will be discussed in this paper. Three from around the turn of the century will be covered, as well as one from this decade. The last demonstrates that the art of creating absurdities has not withered, even after ninety years of scientific sophistication, and some can even be patented. The first three reached field trials due to the gullibility of company management. The last arose from a fortuitous mis-operation of a plant which solved a problem, but the explanation and patent which arose are metallurgically impossible.

Jan 1, 1999

By Ruixuan Zhang, Yan Li, Shusen Cheng

The high temperature distribution of the blast furnace raceway plays an important role in continuous and steady production. There are a number of techniques which have been developed for flame temperature measurements, but most of them have considerable errors and instability. To obtain more accurate results, an efficient optimization algorithm is necessary. This paper presents a novel measurement approach based on the two-color method and an optimization algorithm using images of raceway flame captured by the RGB CCD (Charged-couple Device) camera to calculate the projection temperature distri- bution. Furthermore, both the back-propagation neural network and the principal component analysis are applied to calibrate the correlation between blackbody temperature and the gray-level intensity. Experimental results obtained from the blast furnace raceway demonstrate that the proposed optimization approach performs well in the measurement offlame temperature compared with the measured temperature.

Mar 1, 2017

By Carlos Maurício F. Vieira, Giulio R. Altoé, Maria Carolina A. Teles, Sergio N. Monteiro, Maycon A. Gomes, Frederico M. Margem, Gabriel O. Glória

Due to growing concern about the ambient impacts, the society is demanding for materials that are environmentally friendly. The lignocellulosic fibers, like PALF fibers, appears like an option to replace the synthetic ones in composites with polimerics matrices. Besides the environmental advantages, the lignocellulosic fibers have economical and some properties advantages like the low density in comparison with the synthetic fibers. Nowadays the lignocellulosic are used in industries, like the automobile and aerospace. This objective of this study was to analyze the absorbed impact energy of the composites reinforced with PALF fibers. The fibers were incorporated into the polyester matrix with volume fraction from 0 to 30%. The results showed increase in the absorbed impact energy with the increase of the percentage of fiber incorporated. The fracture surface of the specimens were analyzed by SEM (scanning eléctron microscope) and indicates that the PALF fibers act as reinforcement for the polyester matrix.

Mar 1, 2017

By Nickolas J. Themelis

Nearly thirty two million tons of municipal solid wastes (MSW) are combusted annually in over one hundred U.S. Waste-to-Energy (WTE) power plants, thus reducing the use of fuel oil by about 1.6 billion gallons of fuel oil. One of the advanced WTE processes is the 0.9-million ton/y SEMASS facility at Rochester. Mass. Most of the combustion in the three giant combustion chambers occurs while the injected shredded wastes are in suspension, i.e .? in flash combustion mode. The velocity. temperature, and concentration profiles in the SEMASS combustion chamber were simulated by representing the combustible fraction of MSW by the simplified formula C6HIO04 and using the CFD program Fluent to solve the turbulent energy and mass transport equations. After validation against plant data. this model will be used to examine options for increasing the productivity of WTE combustion chambers, such as optimum distribution of primary and secondary air and oxygen enrichment.

Jan 1, 2003

By Gen Kamimura, Hiroyuki Matsuura

Zinc is widely used for galvanization of steel plates due to its high corrosion resistance. Steel scraps containing waste zinc-coated steel plates are remelted for recycling of steel in electric arc furnace (EAF) process, in which zinc is concentrated in EAF dust ranging from 10 to 40 mass%. Therefore, recycling of zinc from EAF dust is important to secure zinc resource. Our group has proposed selective chlorination and evaporation method recovering zinc as a form of chloride from EAF dust. Since recovered zinc chloride may contain lead, iron and copper as impurities, purification of zinc chloride is essential for production of highly pure metallic zinc. In the present study, removal of lead chloride from molten zinc chloride-alkali chloride by cementation reaction adding zinc was investigated. Experimental results were analyzed and discussed thermodynamically and kinetically as well as the feasibility and limitation of this process were examined.

Mar 1, 2018

By D. M. Fermino, C. G. Bastos Andrade, M. G. Fernandes, F. R. Valenzuela-Diaz

Treatments with high concentration solution of inorganic acid at temperatures under boiling point are a usual method for clay minerals structure modification. For many industrial uses bentonites must be cleared of impurities. In the present paper, a sample of Brazilian bentonite from Vitoria da Conquista, Bahia was modified by mild acid attack using hydrochloric acid under moderate conditions (90 °C, reaction times of 1, 6, 12, 18 and 24 h in close reactor, concentration of the aqueous solution of hydrochloric acid 1.5 M, acid solution/clay ratio of 1 g/10 mL). The attacked samples were characterized by CEC, XRF, SEM, EDS and Stereomicroscopy. The purpose of these attacks is to reduce the concentration of impurities with minimal damage in clay minerals structure. The modified bentonite presented good results and tends to be a good economic and environmental alternative to manufacturing products with high added value such as polymer/clay nanocomposites, cosmetics and medicines.

Mar 1, 2017

Thallium is a very minor element found in lead ores. It's behaviour during lead smelting has recently become of much greater interest due to the effects it had on the health of waste heat boiler maintenance contractors at a Canadian smelter. In this paper the behaviour of thallium in both traditional and direct lead smelting processes will be examined using computational thermodynamics techniques. Yazawa and his coworkers have made extensive use of computational thermodynamics to examine and illustrate pyrometallurgical processes. It has been shown that thallium behaviour during smelting is strongly influenced by the extent of oxidation of the lead concentrate and by the presence or absence of chlorine in the charge. The condensation behaviour of thallium species in the waste gas handling system was also modelled and it has been confirmed thallium-rich deposits can form at the high temperatures prevailing in waste heat boilers.

Jan 1, 2003

By Mingming Zhang, Udaya Bhaskar Kodukula, Marcelo Andrade

The physical and chemical properties of sinter feed are important factors that determine the productivity and quality of sinter product. In this study the feasibility of treating sinter feed by high pressure grinding rolls (HPGR) is investigated for selective cracks generation exploiting weak zones along grain boundaries of poor quality iron ores without generating much fines. The pre-treated sinter feed was characterized for size distribution, surface area, contact angle, and SEM analyses. The characterization results indicated that surface area of the pre-treated sinter feed sample increased about 20%. Pot-grate sintering tests results also indicated improvement on cold permeability, sintering yield and productivity, sinter Tumbler index, and low temperature degradation index (LTD) after HPGR pre-treatment.

Mar 1, 2018

By Ruirui Wei, Mingrui Yang, Xueqing Li

Ultrasonic vibration was introduced into calcium ferrite (CF) melt in order to develop a new sintering process. Based on the acoustic refraction and reflection principles, ultrasonic propagation between amplitude transformer and CF melt has been analyzed and discussed. In addition, numerical simulation of ultrasonic propagation in CFmelt has also been carried out using finite element method. The distribution of acoustic pressure in CF melt were obtained, and the effects of ultrasonic power and frequency on acoustic pressure distribution were also investigated. The results show that increasing ultrasonic power promotes the acoustic pressure amplitude in the CF melt, while increasing frequency decrease the acoustic pressure amplitude. The acoustic pressure amplitude with the frequency closer to the resonant frequency may get the best cavitation effect because its average acoustic pressure is greater than those of others.

Mar 1, 2018

By Yuanbo Zhang, Daoyuan Zhang, Youlian Zhou, Guanghui Li, Tao Jiang

"Modified humic acid (MHA) has been developed by Central South University (CSU) and authorized in China. It has been reported that MHA is an effective binder for oxidized pellets prepared from specularite concentrates. In this research, effects of MHA binder on roasting behaviors of the specularite pellets are studied. MHA is an organic binder, containing much carbon, hydrogen, oxygen, etc. During the roasting, MHA can provide some heat because of combustion of hydrocarbon, which is beneficial for the recrystallization of Fe2O3 in the specularite pellets at high temperature. Simultaneously, part of hematite particles within the pellets are firstly reduced to magnetite, then, magnetite is oxidized into secondary hematite, which obviously improves the roasting performance of specularite pellets.IntroductionOxidized pellets have been widely used in steel production as a kind of high quality burden for blast furnace ironmaking [1]. In recent years, production of oxidized pellets is developing very fast. Therefore, the supply of high quality magnetite concentrates, which is the most suitable for pellet production, becomes scarce. It is imperative to pursue new alternative materials for oxidized pellet production [2]. Specularite concentrates have attracted widespread attention due to the advantages of high total Fe grade and low impurity content. However, due to the poor ballability and firing performance, specularite has not yet been widely applied into pellet production [3, 4]."

Jan 1, 2012

By Xueqin Li, Xuewei Lv, Yu Zhang, Wenchao He

In recent years, a new process of “direct reduction-electric furnace smelting separation” has been put forward and developed for recovering the iron, vanadium, titanium and chromium to make full use of the chromium-bearing vanadium titanium magnetite. In the present work, FactSage, one of the most frequently-used thermodynamic calculation software, was used to calculate the migration of Fe, V, Cr and Ti with different nC/nO (mole ratio of carbon and oxygen). The calculation results indicate that the recoveries of Fe, V and Cr increase with increasing nC/nO and temperature respectively. In addition, the recoveries of Fe, V and Cr are up to 90% when the nC/nO value is more than 1.15.

Mar 1, 2018

By A. Arenas-Flores, Pandiyan Thangarasu, J. P. Hernández-Lara, F. R. Barrientos-Hernández, J. A. Romero-Serrano, A. Hernández-Ramírez, M. Pérez-Labra

BaTiO3 doped with Gd3+, was synthesized from BaCO3, TiO2, and Gd2O3 as powders using the solid state reaction method (Ba1-xGdxTi1-x/4O3). The milling of the precursors was performed in an agate mortar with acetone as control means and compositions x = 0.001, 0.005, 0.05, 0.15, 0.25, 0.35 Gd3+ (wt%). Firstly, the powder mixture was decarbonated at 900 °C for 8 h, after it was sintered at 1400 °C for 5 h. Tetragonality of synthesized BaTiO3 doped with Gd3+ was analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM) and Raman spectroscopy (RS). Subsequently, the powders sintered were uniaxially compacted cold until to obtain pellets of about 10 mm in diameter; which again were sintered at 1400 °C for 4 h. XRD patterns and Raman spectra results revealed that the crystal phase of the obtained particles was predominately tetragonal BaTiO3.

Mar 1, 2017

By C. M. Dentan

Conventional testing of crude kaolin ores emphasizes physical properties as they relate to end uses of kaolin products. This approach to evaluating crude ores does not reveal the basis of behavioral differences between typical coarse and fine kaolins from central Georgia. Optical and scanning electron microscopy in combination with XEDS have been employed to characterize both coarse Cretaceous and fine Tertiary kaolin in order to shed light on the reasons for the gross differences in their properties. Routine evaluation of various parameters was also carried out. Bulk densities were 1.48 g cc-l for the coarse clays and 1.53 g cc-1 for the fine clays. Surface areas were 15 m2 9-1 and 25 m2 9-1, respectively. Brookfield viscosities were low for the coarse clays at 70% solids, and high for the fine clays. The situation was reversed for Hercules viscosities. Sixty percent of the coarse clays had particles of less than 2 um and the fine clays had 90% less than 2 cm. Micrographs of thin sections prepared from blue-dyed epoxy-impregnated crude ores and of SEM fabric samples demonstrated vivid differences in texture. Cretaceous kaolins appeared to be completely recrystallized residual products of former aluminous sediments, while Tertiary kaolins retained their essentially sedimentary character. Differentiation of the coarse and fine kaolins is rapidly accomplished by both optical and scanning electron microscopy, and should be considered a valuable analytical technique in evaluating kaolin ores.

Jan 1, 1981

By Takashi Araki

In this work, we have elucidated the two-step oxidative reaction mechanism of 2,4,5-trichlorophenol by adsorbing oxygen atom for oxidative decomposition reaction of 2,4,5-trichlorophenol on oxide catalyst surface using ab initio molecular orbital calculation. In the first oxidation, total energies of reaction products have been shown extremely stabilized at all oxidation positions. This reaction occurs due to charge transfer from benzene ring to adsorbing oxygen atom. As a result, ? bonding of benzene ring are weakened. However, the benzene ring of 2,4,5-trichlorophenol does not perform cleavage reaction. In the second oxidation, the benzene ring of 2,4,5-trichlorophenol can perform cleavage reaction, since the second oxidation obtains larger stabilized energies than the first oxidation.

Jan 1, 2003