Search Documents

By Khaled Morsy

This study presents a typical stress-strain model for coal material using the available in-situ and laboratory tests data conducted on coal. This model can be used as a basic coal model in finite element applications The effects of pillar width-to-height ratio and the confining pressure have been considered in this model. The extended Drucker-Prager model with mobilized friction angle was found to be very successful in simulating the proposed model.

Jan 1, 2001

By Yi You

A research has been conducted to study the long-term subsidence and its possible effects on surface structures In this research, the surface movements in areas when potential for developing long-term subsidence is high have been monitored over an extended period of time Long-term subsidence data have also been collected from other sources The avail- able data from this on-going research have been analyzed and the results is presented in this paper.

Jan 1, 1997

By Jim Galvin

4 and 6 point timber chock constructions are used extensively on both a systematic and spot basis by Australian longwall operators to support tailgate roadways. In 1996, the School of Mining Engineering at UNSW published design and performance criteria for timber chocks constructed from Australian hardwoods. The research was funded by the Australian Coal Association Research Program (ACARP). In 1997, ACARP awarded funding for a stage 2 testing program. This testing focussed on examining the effect of using thinner timber elements in chock constructions to improve OH&S and comparing the full-scale performance of traditional 4 point chocks to Link-n-Lock constructions. It was established that chocks constructed from thinner elements have failure loads much less than thicker elements. However up to the failure loads of the thinner elements there was no significant difference in the response to convergence of chocks constructed from 25, 50 or 100mm thick elements. Chocks constructed from 150mm thick elements have a similar ultimate strength to the 100mm thick elements. However, they have a significantly lower resistance to load, thereby permitting more convergence to occur. There is more potential for chocks comprised of thin elements to be constructed 'out of plumb' and so suffer eccentric loading. The full scale testing program established that at any given level of convergence up to 10% strain, the timber in a Link-n-Lock chock generates twice the support resistance of the same quantity of the same timber in an equivalent size 4 pointer chock. On the basis of support resistance per cubic metre of timber, there is only a marginal difference in the performance of 1.0m Link-n-Lock chocks and 1.2m Link-n-Lock chocks constructed from select Blue Gum. The cost per tonne of support provided by a Link-n-Lock chock is effectively half of that provided by a 4 pointer chock of equivalent dimension and timber. Up to a strain level of 4%. Link-n-Lock chocks constructed from 1.2m long elements are slightly more cost effective than the same chocks constructed from 1.0m long elements. Thereafter, there is no significant difference in cost per tonne of support resistance. Beyond a strain level of about 4%, Link-n¬Lock chocks constructed from landscape grade Blue Gum are just as cost effective as Link-n-Lock chocks constructed from structural grade 4 Blue Gum.

Jan 1, 2000

By Thomas Barczak

Pumpable roof supports provide an alternative longwall tailgate roof support and have grown in usage during the past few years. Heintzmann Corporation has been installing pumpable roof supports at the RAG Resources Emerald Mine in western PA since 1998, where they have provided effective roof control in their longwall tailgates. Despite the success of these supports in this application, questions remain regarding critical design issues for optimizing the use of this support technology. The support loading profile is characterized by a high initial stiffness with peak loading occurring at less than one inch of convergence, followed by significant load shedding with a post failure capacity comparable to that of wood cribbing. Therefore, the key to optimizing the support utilization is to provide sufficient load density to prevent convergence from occurring beyond the peak loading capacity. This requires an understanding of how the supports interact with the ground conditions, hence measurement of the ground reaction curve. In order to obtain this information, pumpable roof supports were instrumented to measure support loading. Roof deformation and roof-to-floor convergence measurements in the vicinity of the instrumented supports were also made. The experimental parameters for the installation were the support spacing and water¬to-solids ratio of the grout, which controls the grout strength and ultimately the maximum capacity of the support. The study clearly shows that at this mine a 24-inch diameter support is fully capable of providing adequate ground control under depths of cover of 750 ft as only 50 pct of the available support capacity was utilized outby the longwall face. It was also shown that the 2.00 to 1 water¬solids ratio, despite providing a slightly softer support response, is sufficient for maintaining the same degree of roof control provided by the traditional 1.75 to 1 grout mix. The 10-ft spacing of the supports did not cause any ground control problems outby the face. However, inby the face the performance of the support is degraded once the peak capacity of the supports is exceeded. It appears that the large load shedding behavior, which is characteristic of this support following peak loading, allows the immediate roof to separate. When this happens, the support is unable to regain control of the roof in time to prevent failure of the immediate roof beam.

Jan 1, 2003

By David C. Johnson

Coal mining in Illinois has resulted in many structures being exposed to subsidence damage. Damage mitigation techniques (DMT) applied in the foundation design/construction have proven successful in minimizing damage in several test cases. To determine the practicality of these techniques, the Costs of their application are investigated. The AMT costs are compared to foundation and total house costs for various classes and sizes of houses. An economical and effective subsidence resistant foundation construction is proposed.

Jan 1, 1993

By Christopher Mark

Despite more than half a century of experience with roof bolting, no design method has received wide acceptance. To begin to improve this situation, National Institute for Occupational Safety and Health (NIOSH) conducted a statistical study of roof bolt performance at a number of mines throughout the U.S. Case histories were collected from 37 mines with a variety of roof bolt types and patterns in a wide range of geologic environments. Performance was measured in terms of the number of roof falls that occurred per 10,000 ft of drivage. The study found that roof falls are rare when the roof is strong and the stress is low, even with light roof bolting patterns. The focus of this paper is on the more difficult conditions, where the roof is weaker and/or the stress is higher. Analysis of the results led to guidelines that can be used to make preliminary estimates of the required bolt length, capacity, and pattern. The guidelines are based on the depth of cover (which correlates with stress) and the roof quality (measured by the Coal Mine Roof Rating (CMRR), and the intersection span. Another contribution is a formula for estimating the horizontal stress level in the eastern U.S. coalfields as a function of the depth of cover. The design guidelines are currently being implemented into a computer program called Analysis of Roof Bolt Systems (ARBS).

Jan 1, 2001

By John Feddock

This study deals with underground mines and ground control and the prediction of seats strength characteristics based upon ultrasonic logging. Exploration drill holes, both rotary and core holes are used for proving coal reserves and determining mining parameters. Drill hole cores can be subjected to geologic study and geotechnical evaluation. In addition, the use of geophysical logging techniques is well established in determining certain strata characteristics and ground parameters. Since the characterization of the rock mass in mines remains insufficient in most cases, the idea of possibly characterizing the strength parameters without expensive core retrieval and laboratory testing is very attractive. The elastic properties of the rock can be deduced from measurement of the sonic velocity if the density is known. Through the use of in-hole geophysical density logging combined with an ultrasonic logging tool, the estimation of strata properties is possible. An investigation was conducted at two Indiana underground coal mines using geologic logging, geophysical logging, ultrasonic logging and laboratory strength testing to establish the strength properties of the roof rock. A specialized ultrasonic logging tool with one transmitter and two receivers enables nearly continuous readings along the length of the hole. The results of correlating portions of the data are presented. It is anticipated that the ultrasonic logging will be a supplemental tool for extending laterally the strata characteristics obtained from the existing program to surrounding areas. This may be obtained from the relatively inexpensive logging data obtained by ultrasonic logging.

Jan 1, 2003

By David I. Hoyer

It is shown that by monitoring longwall leg pressures in real time, warning can be given for significant weighting events and the formation of roof instabilities, such as roof cavities, several hours in advance. Longwall Visual Analysis (LVA) is a software package that continuously monitors shield pressures and shearer position in longwall mines. LVA has been running on 19 Australian longwalls for up to four years, and as a result a very substantial database of shield pressure trends in a wide range of longwall situations has been collected. This database has been analyzed to develop indicators that will give operators and geotechnical engineers advance warnings of developing conditions such as weighting events and difficult roof conditions. LVA displays live charts of data, such as shield leg pressures, loading rates, and yield frequencies. Data analysis techniques were applied to historical data records from multiple longwall sites in order to develop a ?Cavity Risk Index? (CRI). The CRI indicates the risk of roof cavities developing, and it is based on pressure trends that indicate significant yielding and loading rates spanning a region of relatively low support. Case studies from different longwalls are given, showing how the CRI can give real-time advance warning of the formation of roof cavities with their anticipated location on the face. The limited number of case studies done so far indicate that the predictions have a high degree of reliability, but more work is required to quantify this.

Jan 1, 2011

By Robert A. Stansbury

The No. 14 Mine of United States Steel Corp- oration is located at Munson, West Virginia, in &Dowell County. The mine was originally assigned 7,530 acres of Pocahontas 3, 4 and 5 Seams. Production began in 1948 with a listed reserve of 64,500,000 in place tons. It was originally intended to superimpose the 4 Seam workings with the 3 Seam and mine the two simultaneously to minimize the effects of one seam on the other. Roof control problems and economic conditions led to the discontinuance of 4 Seam workings in 1958 and again in 1980, after reopening in 1972. With room and pillar mining continuing in the 3 Seam, the majority of the 4 Seam reserves have been undermined. The mine began operation using track mounted conventional equipment. Off-track conventional equipment was next used, and in 1957 continuous miners were introduced. Since this tie, continuous miners on room and pillar work have been exclusively used with the exception of a brief shortwall trial in the 4 Seam in 1975. By mid 1982, 3 Seam mining will have been completed, leaving an estimated 42 million in place tons of 4 and 5 Seam coal as the focus of mining efforts. Plans for the subsequent reopening of the 4 and 5 Seam workings have been scheduled for June of 1981. With the resumption of mining, management is faced with solving the roof support problems caused by both the inherent physical conditions and undermining.

Jan 1, 1981

By Gregory M. Molinda

An investigation was conducted to determine the nature and frequency of coal mine roof failure beneath valleys. A mechanism for this failure, and suggestions for controlling this problem are presented. Hazardous roof conditions identified in a number of mines were positively correlated with mining activities beneath stream valleys. Mine maps with overlays of unstable roof and locations of stream valleys show that 52% of the instances of all unstable roof in the surveyed mines occurred directly beneath the bottom-most part of the valley. The survey also showed that broad, flat-bottomed valleys were more likely to be sites of hazardous roof than narrow-bottomed valleys. Evidence of valley stress relief was found beneath a number of valleys in the form of bedding-plane faults and low-angle thrust faults. This type of failure, previously believed to be only a shallow phenomenon, was found at mining depths as great as 300 ft. In situ horizontal stress measurements in a mine beneath a valley and the adjacent hillsides confirmed valley stress re1ief. Underground mapping showed that roof falls in excess of 100 ft in length and up to 25 ft high closely aligned with the valley axis. Numerical analysis of 13 valleys overlying one mine property showed the effect of the valley excavation on horizontal and vertical stress. Thickness of cover, valley shape, and the orientation of the valley relative to the maximum regional horizontal stress all influence the "valley effect" on roof stability.

Jan 1, 1990

By N. C. Saxena

Subsidence investigations in Indian coalfields have led to development of relationships between subsidence movement parameters and defining of safe limits of subsidence movements for surface properties. The maximum subsidence over caved workings was generally not more than 60% of extraction thickness underground while in case of hydraulically sand stowed workings it was generally not more than 5%. The relationships have been useful in extraction of more than 7-million tonne of coal from underneath and in the vicinity of surface properties.

Jan 1, 1988

By Craig Compton

The The National Institute for Occupational Safety ane Health (NIOSH) Pittsburgh Research Laboratory (PRL) is continuing to investigate the behavior of fully grouted roof bolts in the weak roof rock of the Safety Research Coal Mine (SRCM). This paper describes the results of three studies: A series of 24 pull tests of bolts installed fully grouted and overcored to leave 12 inches of grouted bolt. The tests compared the pull-out performance of offset-head roof bolts with that of standard 518-inch bolts; A second series of 24 tests that compared the pull-out loads obtained by bolts installed with 1 R of resin (a Short Encapsulation Pull Test or SEPT) to that of fully grouted bolts overcored to leave only 12 inches of grouted bolt, and An investigation into the pressures generated during the installation of fully grouted resin bolts. All of the bolts installed and pulled were overcored and removed from the roof after the pull tests to allow inspection of the resin. The first study found that there was no significant difference in pullout load between the offset-head bolts and the standard bolts. The second study, comparing the SEPT bolts and the partially- overcored fully grouted bolts, indicated that SEPT can significantly underestimate bolt anchorage grip factor, suggesting that the SEPT is a conservative measure of actual bolt performance. Significant loss of resin to cracks in the roof was observed in the bolts overcored in the SRCM. The third study explored one possible explanation for the resin loss, high pressures generated during bolt installation. These tests employed bolts installed in strain gauged steel tubes. The results confirmed that significant pressures (greater than 4,000 psi) can be generated during bolt installation. The results of the pressure tests, combined with the observations of resin loss in bolts installed in the SRCM, suggest that under some circumstances resin loss and under-encapsulation could take place and lead to degraded bolt performance. Glove fingering was observed in all recovered bolts to various degrees. The limited comparative data suggested that the effect of glove fingering ranged from slight to moderate. Complete mixing of the resin was observed on all of the 40 bolts recovered (28 fully grouted and 12 SEPT). Australian and U.S. resins were compared and the Australian resins were observed to have much smaller catalyst compartment areas and lower resin viscosities. These differences are suggested as potential explanations for occasional resin mixing problems noted in Australian resin bolt installations.

Jan 1, 2005

By Vincent A. Scovazzo

The Pennsylvania Joint Coal and Gas Committee Gas Well Pillar Study of 1956 is the bases for well protection pillar design in the US and many other countries. An update was necessary because the well construction common to the gas and coal industries as well as mine configurations, mine depth, and extraction thickness have changed considerably since 1956. As initially envisioned the update would involve a similar empirical study that formed the basis of the initial investigation. However, there are no records of any gas or oil well failures related to coal mining since 1956 when mines followed the initial recommendation, making an empirical study problematic. Thus, the study had to be more analytical, which in return required at least some fundamental research into the behavior of the interaction of coal mining and oil and gas wells. A call to industry about research they have undertaken resulted in obtaining excellent research on the subject from three companies; Alpha Natural Resources, Inc., CONSOL Energy Inc., and Range Resources. These research projects were initially undertaken for internal use and not previously published. John T. Boyd Company reanalyzed these studies and determined how their results would affect protective pillar designs. These research projects pointed to the importance of horizontal movement and shear caused by subsidence and the strength of pillars and their foundations. The importance of geology is important in understanding horizontal shear, ground movement, and floor strength. The failure modes of casing and pipe needed to be understood so the threshold of these movements and stresses could be determined.

Jan 1, 2013

By Syd S. Peng

Full-face shield leg pressures in a longwall panel for a three-month period were collected and analyzed. The pressure data were presented in the following forms: full- panel full-face shield pressure, individual shield pressure, full-face shield pressure, full-panel time-weighted-average pressure, and relationships among setting pressure, final pressure and pressure increment. Although shield pressure varies from shield to shield and from cycle to cycle, the setting pressure and face advance rate do control the 6nal pressure and time-weighted average pressure.

Jan 1, 1997

By Shugang Li

The layout and efficiency of the degasification system is heavily dependent on the distribution of and the methane migrating mechanism in the mining induced fractures in the overburden strata In this paper, physical modeling and numerical simulation are employed to study the mining-induced fracture zones and the stress distribution in these zones. The physical models show that both the fracture and compaction zones form a parabolic shape in the over- burden strata along the panel transverse direction. When this is generalized to the panel longitudinal direction, the shape of the mining induced fracture zone over the longwall gob can be represented by a 3-D elliptic paraboloid function. Through the observation of bed separation, fracture density and distribution pattern in the physical models, it is believed that the development of the parabolic fracture zone can be divided into three distinguishable phases. The expansion characteristics and sizes of the fracture zones can be estimated. The numerical stimulation studies can be used to estimate the extent of the stress release zones. The stress release zones can be also divided into a high compressive stress - fracture closure zone, stress relieved - fracture expansion zone, and intact zone. The methane desorption model is then used to analyze the methane migrating pattern in the fracture zone. The developed model has been verified by the results of a longwall gob degasification tests at a coal mine in Yangquan, China with a fair agreement. Such studies show that the model can provide a reasonable accurate tool for designing the gob-well degasification system for longwall mining operations.

Jan 1, 2005

By Brad Seymour

In cooperation with Cyprus Twentymile Coal Co., researchers from the National Institute for Occupational Safety and Health (NIOSI-I), Spokane Research Laboratory, conducted a study at the Foidel Creek Mine, an underground coal mine near Oak Creek, CO, to evaluate the stability of underground working conditions as a longwall advanced through a series of backfilled cross-panel entries. Instruments installed in the cross-panel entry pillars, backfill, longwall panel, and adjacent headgate entry were continuously monitored by a computerized data acquisition system as the longwall approached and advanced through the backfilled section of the panel. Data collected from these instruments were analyzed to determine the magnitude and direction of the secondary principal stress changes ahead of the longwall face, deformation and closure of the headgate entry, and stability of the cross-panel entry pillars and backfill. A three-dimensional, boundary element model was calibrated to accurately predict mining-induced stress changes and the distance they occurred ahead of the longwall face. As the longwall advanced through the backfilled entries, most of the mining-induced load was supported by the cross-panel entry pillars. The backfill provided stability for the root and Moor of the in-panel entries and also confined the entry pillars significantly improving their load-carrying capacity. Comprehensive information derived from backfill material property tests, instrument data, underground observations, and numeric modeling results document the safety and stability of the 8-Right minethrough and should provide beneficial case study information fur other longwall backfilling applications in the future.

Jan 1, 1998

By Yong-Ming Jiang

In cooperation with Cyprus Twentymile Coal Co., researchers from the National Institute for Occupational Safety and Health (NIOSI-I), Spokane Research Laboratory, conducted a study at the Foidel Creek Mine, an underground coal mine near Oak Creek, CO, to evaluate the stability of underground working conditions as a longwall advanced through a series of backfilled cross-panel entries. Instruments installed in the cross-panel entry pillars, backfill, longwall panel, and adjacent headgate entry were continuously monitored by a computerized data acquisition system as the longwall approached and advanced through the backfilled section of the panel. Data collected from these instruments were analyzed to determine the magnitude and direction of the secondary principal stress changes ahead of the longwall face, deformation and closure of the headgate entry, and stability of the cross-panel entry pillars and backfill. A three-dimensional, boundary element model was calibrated to accurately predict mining-induced stress changes and the distance they occurred ahead of the longwall face. As the longwall advanced through the hackfillcd entries, most of the mining-induced load was supported by the cross-panel entry pillars. The backlill provided stability for the root and Moor of the in-panel entries and also confined the entry pillars significantly improving their load-carrying capacity. Comprehensive information derived from backfill material property tests, instrument data, underground observations, and numeric modeling results document the safety and stability of the 8-Right minethrough and should provide beneficial case study information fur other longwall backfilling applications in the future.

Jan 1, 1998

By Paul A. Lu

This paper proposes an unconventional, simple, and practical method of measuring mining-induced around stresses with hydraulic borehole pressure cells. The method is a direct ground stress measuring technique. It does not require the value of deformation modulus for back-calculation of stresses; instead, it directly measures the ground stress in situ. The applicability and practicality of the technique are shown by two case studies. The technique may be applied to monitoring a stress build-up that may lead to mine roof failure or to rock and coal outbursts.

Jan 1, 1984

By Edward S. Custer

Recent investigations of mine roof falls have demonstrated that roof failures are generally associated with geologic conditions. The roof falls can be predicted by using the techniques of depositional modeling for the coal bed and roof rocks, and by lineament analysis. The ability to predict potential roof failure areas will allow the engineer and mine planner to develop a mine plan to avoid the roof failure areas and thus reduce overall mining costs. The ability to avoid roof failure areas also will permit maximum recovery of the coal resources.

Jan 1, 1981

By Charlie Li

A cut-and-fill mine stope, located at a depth of about 1000 m in a lead-and-zinc mine, was closed down because of large roof convergence and fractures appearing on the hanging wall. The instability problem was owing to the relatively low strength of the rock subjected to high in-situ stresses. Extra reinforcement was required to secure the stope so that the remaining ores in the stope could be mined. Assessment of the fracture mode in the country rock surrounding the stope was carried out and then the reinforcement de- sign was worked out. It was proposed that the unstable section of the stope would be reinforced by bolt-shotcrete ribs as well as selective long bolts. The philosophy of the design was to hold up the fractured country rock by bolts and shotcrete so that a load-bearing arch could be formed in the roof and in the hanging wall. Six shot- Crete ribs were set up in the unstable section of the stope. Displacement measurements showed that the roof convergence reduced from about 2 &day to the ordinary creeping level, about 0.25 &day, immediately after the reinforcement operation. Six month later, the hanging wall collapsed into the stope in a place just outside the reinforced section, which indirectly proved the effectiveness of the bolt-shotcrete ribs in reinforcing the fractured country rock. This case showed that an appropriate rock mechanics assessment would form a solid base for reinforcement/support design. It also provided an evidence for the philosophy of the reinforcement by bolt-shotcrete ribs - establish a load-bearing arch in the rock.

Jan 1, 2005