Search Documents

By Jimenez Leon, Christopher Newman, Boede Gabriel, Zacharias Agioutantis

"Ground movements due to longwall mining operations have the potential to damage the hydrological balance within as well as outside the mine permit area in the form of increased surface ponding and changes to hydrogeological properties. Recently, the Office of Surface Mining, Reclamation and Enforcement has completed a public comment period on a newly proposed rule for the protection of streams and groundwater from adverse impacts of surface and underground mining operations (80 FR 44435). With increased community and regulatory focus on mining operations and their potential to adversely affect streams and groundwater, there is now a greater need for better prediction of the possible effects mining has on both surface and sub surface bodies of water.As mining induced stress and strain within the overburden is correlated to changes in the hydrogeological properties of rock and soil, this paper investigates the evaluation of the hydrogeological system within the vicinity of an underground mining operation based on strain VALUES (calculated through a surface deformation prediction model. Through accurate modeling of the pre- and post-mining hydrogeological system, industry personnel can better depict mining induced effects on ground water flows through the overburden material aiding in the optimization underground extraction sequences while maintaining the integrity of surface and subsurface bodies of water.INTRODUCTIONThe utilization of high-recovery underground mining methods, such as longwall or high-extraction room-and-pillar operations, have the potential to cause adverse impacts to both surface and subsurface bodies of water as strata movement and deformations propagate from the mined seam through the overburden to the surface (Peng, 2008).Previous research has indicated that mining induced strains are the most damaging to surface streams (Singh, 1992) as well as greatly affecting the integrity of subsurface bodies of water and groundwater flow conditions (Booth, 1986). On the surface, adverse effects to the stream can occur due to the development of either tensile or compressive strain in the stream bed. The development of tensile cracks along the bedrock allows for a potential loss of stream flow through developed fissures. In fact, water flow in the Cataract River of Australia ceased in 1994 as a result of mining-induced strains from longwall operations in the Bulli seam 430 meters (1320 feet) below the river gorge (McNally and Evans, 2007). On the other hand, the development of compressive strains within the rock layers can cause rupturing or buckling of the stream bed, blocking stream flow and/or diverting flow into the fractures at the base (Iannacchione et al, 2010). While these localized fractures can contribute to the loss of stream flows, given time, damaged streams have the ability to self-heal through the regeneration of near-surface aquifers as well as the sealing of mining-induced fractures with rock debris, gravel, sand, clay or other soil particles carried from upstream sources and deposited in the river bed (Waddington and Kay, 2002)."

Jan 1, 2016

By Jonathan P. Furniss

The paper describes a range of laboratory tests undertaken on full column resin anchored glass fibre rockbolt systems, to assess all aspects of their performance. Laboratory instrumentation has been developed for the accurate study of strain transferral from the Glass Fibre Reinforced Plastic (GRF') bolt, through the surrounding resin annulus, and into the rock. Experience in laboratory testing to the new British Standard on glass fibre rockbolting is discussed. A critical comparison is made of the influencing parameters affecting . underground rockbolted roadway performance to the parameters assessed by BS 7861 : Part 1 The work has been co-funded by MA1 Systems UK Ltd. who supply GRP rockbolt components to the British coal mining industry, mainly for the reinforcement of coal ribsides. In rockbolting, glass fibre has a number of useful * qualities which are discussed in the paper. These properties, make the product more suitable than steel in certain applications, both in mines, and other engineering structures such as tunnels, soil stabilisation, and coastal defences.

Jan 1, 1997

By Richard R. Wilding

The United States Coal Mining Indus- try had the opportunity to greatly improve their roof control techniques during the nineteen seventies by the use of fully grouted resin roof bolts. This new tool was first approved for underground coal mines by M.S.H.A. ten years ago and during the next decade has been perfected to meet many problems previously thought to be unsolveable. The initial approved cartridge was very similar to the ones used in Europe in the nineteen sixties and since then has undergone a great deal of modification for our mines. These refinements in cartridge construction have been obtained by the close cooperation of resin manufacturers with mining personnel in perfecting pro- ducts customized to particular needs. This type of continuing program naturally necessitates a responsibility upon the resin anchor manufacturer to maintain a competant technical department. These roof control technicians by constant exposure to many of the most demanding underground problems, have developed through the years into leaders in successful applications. Today, Celtite has over twenty technically trained underground technicians with an accumulation of over one hundred years experience in resin anchors. Our documented technical reports are in excess of five thousand, involving over six hundred mines representing every major coal mining area in most mineable seams. This department has been the implement used to work with our research and development people in perfecting a continual line of improved resin anchors. This program has been a significant factor in leading the resin anchor industry into a position where approximately one third of the 1980 under- ground coal production used the fully grouted system. However, as gratifying as this accomplishment is, our experience has lead us to believe that there is an additional demand for a roof control system capable of combining the mechanical bolts ability to apply tension with resins proven superiority in anchoring. A significant number mines visited during the last decade had problems that we believed could be better answered by applying tension rather than the fully grouted approach. In most in- stances, their current mechanical installations were doing an adequate job until anchor slippage occured. Fully grouted systems solved this bleed-off problem. However, an acceptable number of falls still occured. In these some- what unique areas which we believe may amount to as much as fifteen percent of the total bolt installations, the need for improved anchors was a necessity. In developing this program we listed the ultimate requirements necessary for both the bolt and the anchor. These are for the bolt: A. Have one end manufactured so it can be grouted to the mine roof with polyester resin, obtaining a variable length from 12" to 36". B. Have a mechanism which allows the operator to tension the roof from zero to 10,000 psi. This mechanism should indicate if the roof is in compression and the bolt in tension. C. Have a mechanism which allows the operator to thoroughly mix the resin. D. The head of the bolt should not extend below the roof line any more than a normal mechanical bolt. E. Not require any extra tools for installation. F. Be bendable for use in low seam coal. G. Be durable and inexpensive. The ultimate point anchor resin should have the following characteristics: A. Have a mix and gel cycle which would compete with a mechanical bolt for speed of installation. B. Have a pull out strength in excess of a normal 5/8" mechanical bolt.

Jan 1, 1981

By Andrew Starkey

Ground anchorage systems in the form of rock bolts are used extensively throughout the world as supporting devices for civil engineering structures such as bridges and tunnels. It is widely recognized that non-destructive testing methods for ground anchorages need to be developed as a high priority [1 ], with only a small proportion of anchorages currently being monitored in service [2]. The condition monitoring of anchorages is a relatively new area of research, with the objective being a wholly automated or semi-automated condition monitoring system capable of repeatable and accurate diagnosis of faults and anchorage post tension levels. The GRANIT tm system developed by the University of Aberdeen is capable of measuring the integrity of ground anchorages and has won two major UK Awards - the National John Logic Baird Award for Innovation in 1997 and a Design Council Millennium Product Award in 1999. The normal procedure with the GRANIT tm system [3,4] is to train a neural network on dynamic response data that has been sampled from an anchorage over a range of post-tension levels. Further data is needed in order to test the neural network. The paper presents neural networks that have been trained on data taken from a number of anchorages on different sites, and the results of the diagnosis of these neural networks on new test data is presented. The results show that the cross-diagnosis of anchorages is possible, where a neural network trained on one anchorage is capable of successfully diagnosing the post-tension level for an anchorage of similar construction, and the high level of accuracy that can be attained with the GRANIT tm technique is shown. The paper also introduces a mathematical model of the GRANIT tm process.

Jan 1, 2001

By John R. Poland, Benjamin Mirabile

"There are significant ground support hazards to both personnel and equipment when longwall equipment must mine through cross-panel entries. Backfilling support strategies are often cost prohibitive. Additionally, it is often very difficult to install backfill material in full contact with the mine roof in backfilled entries. This paper will demonstrate the use of fiber-reinforced concrete crib material as a method for standing support in longwall cut-through entries. Despite conceptions of poor performance in potentially high convergence environments, fiber-reinforced concrete crib material can be used in longwall support environments subject to high abutment loads and convergence. Central to the proper design of these supports is the use of yield material between crib layers and at the mine roof/crib interface. The placement location of cribs within the cut-through entry has a significant effect on the main roof behavior and associated ground conditions in the longwall abutment zones. It is particularly important to engineer the proper load displacement characteristics of the installed crib to support expected ground conditions. The cost of fiber-reinforced crib supports is less than 50% of backfilling methods.INTRODUCTIONThe design and execution of a longwall cut-through is perhaps one of the most difficult and risky endeavors in the field of ground control. The magnitude of abutment loads and potential for ground failure present a significant safety hazard to underground personnel. In addition, there is significant financial risk, with replacement costs of face equipment exceeding $200 million. Faced with these consequences, it is both advisable and common for an engineer to design ground support with a significant margin of safety. This paper outlines a robust support system that possesses a significant margin of safety along with significantly lower costs than most other support systems employed in similar conditions.SITE PARAMETERSThe mine site described in this study operates in the Herrin No. 6 seam in southern Illinois. The seam height is typically 76- 84 inches. Mining height in gateroads and mains is typically over 96 in, and typical mining height on the longwall face is 82 in. The overburden depth is 950-970 feet in the area of the longwall cutthrough."

Jan 1, 2016

By Nikolaos Polysos

For the planning and driving of gateroads supported by roof bolts a practical concept has been developed in order to determine the geological and rock mechanical parameters derived from exploration drillholes. Based on this, an assessment scheme for the design of roof bolting has been established. The new methods of investigation comprise of geotechnical logging of drill cores for the determination of structural-geological rock characteristics and complementary geophysical well-logging which enables the evaluation of petro-physical and rock mechanical properties. The tools and their measurements will be briefly presented. The relationship between the geophysical log readings and the geotechnical parameters will be illustrated. The aim of the data acquisition is to improve roof bolting design which is based on the assessment scheme. This will be adjusted to the prevailing rock mechanical conditions and stands up to the required stability of the gate roads. In order to ensure consistent data acquisition, a method of core logging has been standardized for the respective demands. To achieve this it was necessary to introduce specific parameters and new methods. For the recording of linear and planar structural elements at the drill core, a special system for the documentation of the angles in relation to each other has been set up. The rock mechanical parameters and their acquisition will be explained. In order to carry out an objective analysis as fast as possible, software has been developed for the acquisition, management and presentation of the data. These programs and their functions will also be presented. The software is characterized by being user-friendly and the flexibility of its interfaces, Different options for the combined presentation of input and evaluated data give a more objective basis for the planning of roof bolt design. Examples will illustrate the operational implementation of the results during the planning and driving phases.

Jan 1, 2001

By Yunqing Zhang

The 3-D numerical modeling using ABAQUS is performed to analyze the mechanisms of the tensioned bolts by taking into considerations excavation sequence, pre-tension, bedding planes and in-situ horizontal stresses. The effect of the pre-tension and the mechanisms of the tensioned bolts are analyzed based on the results from the modeling. Based on field observations, the failure modes for the tensioned bolted strata are classified by their causes and failure mechanisms. The support design consideration for each failure mode is given. Finally, a new design approach is proposed to do the tensioned bolting design using numerical method.

Jan 1, 2002

By James Pile

The San Juan Coal Mine, located near Farmington, New Mexico, supplies the San Juan Generating Station with more than 6 million tons of coal annually. To replace dwindling surface mine production, San Juan installed a longwall in 2002. The roof rock in much of the underground reserve consists of interbedded coals, carbonaceous shales, and mudstones. Roof support consists of fully-grouted roof bolts, both tensioned and non-tensioned, supplemented by modified cable trusses. Short-encapsulation pull tests conducted by San Juan's geotechnical engineering department showed that some of the immediate roof layers provided variable bolt anchorage. To ensure that the roof bolts were obtaining the necessary anchorage, additional tests were conducted in a variety of locations. The results have been used to determine the optimum support design for different areas of the mine. Another series of tests evaluated the performance of several bolt and hole diameter combinations. The experience at San Juan Mine shows that short-encapsulation pull tests can provide the information necessary to improve ground control in variable roof conditions. It also illustrates how a pro¬active geotechnical engineering program can be an essential component of a state of the art underground coal mine.

Jan 1, 2003

By Nicholas P. Kripakov

The unpredictable massive collapse of roof in openings developed under apparently safe and stable roof conditions in coal mines of the United States has been of much concern for many years. One type of massive caving phenomenon is often attributed to cutter roof, a failure that initiates at one and/or both upper corners of an entry and propagates nearly vertically resulting in overall failure with little or no warning. This paper reviews current methods being used to control cutter roof and suggests new alternatives. The impact of basic parameters that include mine geometry, overburden geology, rock properties, and in situ stress conditions is discussed in the context of their relationship to this problem. The effects of various stress control measures are investigated with model analysis to gain insight into means of reducing the high level of stress known to exist at the entry corners of a West Virginia coal mine prone to cutter roof. The results are presented in the paper and the feasibility of their practical implementation is discussed.

Jan 1, 1982

By Kot F. von Unrug

One of the major difficulties in the proper characterization of rocks surrounding excavations is the lack of data. The existing method for strength determination requires core drilling for sample collection, which, when performed from the surface is costly, and when performed underground, in addition to its cost, interferes with the mine operations. I-landling samples tested in the laboratory is troublesome and also influences the obtained results. Over several years. the author has been interested in developing a method of in situ strength determination that could rapidly generate strength data at low cost without a negative effect on mining activities. The recently developed borehole penetrometer is an improved version of the initial design ( 3 inches in diameter), which was used mainly for strength determination of coal pillars. The new penetrometer has been designed to work in 1.5 inch diameter holes. Such holes can be drilled at low cost with either hand held drilling machines or roof bolters. eliminating limitations of the previous system and opening the possibility of broad application. Strength testing of roof rock around longwall pillars is an example of an obvious benefit when designing secondary roof support. In the paper are given the principles of work of the apparatus and examples of the obtained strength data.

Jan 1, 1998

By Christopher Mark

Mine planning for a new reserve is based on information obtained from exploratory coreholes. A critical component of an exploration program is the geotechnical evaluation. Poor assumptions about roof conditions greatly add to the risks of mining. Rock mechanics testing is central to a geotechnical exploration program. Typically, 3 to 5 uniaxial compressive strength (UCS) tests are made to characterize a particular roof unit at a given corehole. The average (mean) of these tests is taken as "The UCS" for that location. Isopach contour maps are then used to show spatial trends in roof strength. Two issues are raised by this traditional approach. The first is due to the large variability in UCS values that is typical even within a single unit from a single hole. The average UCS might be higher at Corehole A than it is at Corehole B, but the difference may not be statistically significant. The second issue is whether widely spaced coreholes can identify valid spatial trends in rock strength. The answer depends upon whether rock strength changes over distances that are longer or shorter than the corehole spacing. This is a classical geostatistical problem. While geostatics have been used to investigate many coal quality parameters, they have seldom been used to evaluate rock strength. This paper describes an extensive investigation of these issues conducted by the National Institute for Occupational Safety and Health (NIOSH) in collaboration with Peabody Energy. The study employed the Peabody Rock Mechanics Data Base which contains more than 10,000 individual test results. Data from four important roof units were subjected to statistical analysis: ? Brereton Limestone above the Herrin 6 seam (Illinois) ? Turner Mine Shale above the No. 9 Seam (Kentucky) ? Sandstone above the Eagle Coal (West Virginia) ? Shale above the Eagle Coal (West Virginia) The study did not find significant spatial trends in rock strength in any of the cases. Perhaps there are none, or perhaps the exploration coreholes were just too far apart to see them. These results have valuable implications for the design of geotechnical exploration programs.

Jan 1, 2004

By Jay Hilary Kelley

This paper proposes a modification of longwall roof support to meet new difficult mining conditions that are anticipated in the future. A gob canopy is a movable appendage attached on the rear of a longwall shield to counterbalance the troublesome forward downward force couple (FDFC). The gob canopy can be swung in both vertical and horizontal directions, powered by hydraulic cylinders. Several functions and applications are de- scribed

Jan 1, 1997

By Craig Byington

The stress-field orientation mapping and analysis (SOMA) technique for determining the operative stress field near mine workings and its relationship to various fracture sets is described using Dickenson-Russell Coal Company's Laurel Mountain mine as an example. Carried to its practical application, this technique ultimately defines the optimal orientation for the mine workings wherein pillars, rather than rock bolts or other roof support methods, dominantly shoulder support of the highest-probability, potential, roof-fall blocks. It also provides a predictive tool describing local variability in rock deformation and in secondary roof support methods. Fracture discontinuities within a rock mass, either as pre¬existing natural fractures or as mining-induced fractures, are uniquely necessary for every brittle-deformation ground failure including roof falls. Prediction and mitigation of roof falls requires quantifying the interaction between the fracture sets and the operative principal-compressive¬ stress-axis orientation (olo). The SOMA technique utilizes the interaction between fractures and 61o, specifically their dilation or closure, to calculate the orientation of 610, and to estimate the orientations of 62o and o3o. A stereonet program is used to organize and statistically analyze the fracture data, and then to determine the optimal orientation for the mine workings. The final step in the SOMA technique involves modeling the Laurel Mountain mine using a 2-D, finite-element, modeling program. This assures that the interpretations regarding the optimal working orientation closely match the deformation features observed in the mine. It also provides a predictive tool describing highly variable stress and strain partitioning, seemingly erratic rock-bolt failures and the interactions between different sets of mine workings within different coal seams. The critical importance of including the fracture sets is well illustrated in the Laurel Mountain mine where the effects of earlier mining of an underlying seam is contrasted in both a fractured and otherwise identical non-fractured model to illustrate the consequences of ignoring fractures in a predictive roof-fall model.

Jan 1, 2004

By Joseph C. Zelanko

Cable bolt support techniques. including hardware and anchorage systems, continue to evolve to meet U.S. mining requirements. For cable support systems to be successfully implemented into new ground control areas, the mechanics of this support and the potential range of performance need to be better understood. To contribute to this understanding, a series of 36 pull tests were performed on 10 ft long cable bolts using various combinations of hole diameters, resin formulations, anchor types, and with and without resin dams. These tests provided insight as to the influence of these four parameters on cable system performance. Performance was assessed in terms of support capacity (maximum load attained in a pull test), system stiffness (assessed from two intervals of load-deformation), and from the general load-deformation response. Three characteristic load-deformation responses were observed. An Analysis of Variance identified a number of main effects and interactions of significance to support capacity and stiffness. The factorial experiment performed in this study provides insight to the effects of several design parameters associated with resin-anchored cable bolts.

Jan 1, 1995

By Hamid Maleki

Mining in the Book Cliffs Coal Field of Utah has historically been associated with seismicity because of high-stress environments and the presence of stiff, competent rocks. Recognizing the geotechnical risks in this coal field, mine engineers have dedicated considerable resources to the study of mine seismicity. In spite of these efforts, there are no engineering procedures for assessing mine seismicity for a new property and in developing mine designs. This paper presents the results of ongoing geotechnical monitoring and stress analyses at a western U.S. coal mine. The intent is to demonstrate the application of geotechnical methodologies in evaluating mine seismicity and stress-control technologies including evolutions in yield pillar designs for variable topographic conditions of the Book Cliffs Coal Field. We show that narrow yield pillars are quite effective in limiting strain energy accumulation along the gateroads and thus the potential for pillar seismicity. At the same time, the pillars provide sufficient resistance to control roof-floor convergence at the headgate, gradually unloading to residual strength inby the face position. Lagging, nonuniform caving of overburden rocks results in periodic stress concentrations at the tailgate comer. The sudden release of strain energy triggers sudden failure of critically loaded coal in this area of the high stress gradient. The three-entry gate pillar configuration promotes formation of long cantilevers and load transfer to the tailgate, contributing to formation of cutters and coal bumps. The source of seismicity is investigated while simulating slip along three sets of joints in two stiff stratigraphic units during multipanel extraction.

Jan 1, 2003

A high strength steel strand bolt has been developed by Barrett, Fuller & Partners as a replacement for conventional rigid bars for primary roof support in coal mines. It is based on a 23mm diameter multiwire steel strand with a tensile strength of 55 to 60 tonnes, The paper summarizes the development of FLEXIBOLT flexible roof bolts, their reinforcement performance and their potential to provide operators, currently reliant on medium to high density roof bolting systems, with a viable, low density roof bolting system offering high roof reinforcement capacity along with the option of installing bolts longer than headroom, in a single pass at the face.

Jan 1, 1993

By Eric Keller, Jamal Rostami, Wenpeng Liu

"Roof and rib instability is an important issue in underground mining. To optimize ground support design, enhance ground stability, and reduce the possibility of roof or rib failure with minimal use of artificial ground support, it is essential to have an accurate understanding of ground conditions. This includes the location of voids, cracks, and discontinuities, as well as information about the different strata in the immediate roof. This paper briefly introduces ongoing research on void detection by using the roof bolter feed and rotation pressure. The goal of this project is to improve the sensitivity of detection programs to locate smaller joints and reduce the number of false alarms. This paper has presented a brief review of the testing procedures, data analysis, logic, and algorithms used for void detection. In addition, this paper has discussed the results of preliminary laboratory tests and statistical analysis of the data from these two drilling parameters used for void detection.INTRODUCTIONRoof falls are one of the most serious and frequent accidents in underground mining. Each year, personnel are injured or killed because of roof falls. Equipment can also be damaged when this occurs. According to Mine Safety and Health Administration statistics collected from 1999 to 2008, ground falls were the largest cause of fatal accidents in underground coal mining, causing around 40% of all fatalities (NIOSH, 2015a). Out of 8 to 10 fatalities and over 800 injuries are recorded each year in underground mines, there are nearly 2,000 reportable non-injury ground falls every year (NIOSH, 2015b).Certain features in the ground, such as voids, cracks, and discontinuities, are significant factors that cause roof support failures and roof fall accidents. Currently, several manufacturers provide smart roof bolters with limited capabilities for void detection. While successful in many instances, in laboratory experiments, the existing void detection systems have limited success in detecting void openings that are less than 1/8 inch This limited success was observed in testing concrete blocks with gaps in between, simulating a rock medium with voids. Detection programs have missed some voids, while, in some cases, they have shown false detection. These algorithms need to be more accurate in sensing voids to improve the capabilities of these programs."

Jan 1, 2016

By Ulrich Langosch

In the 1990s the German mining industry introduced a new generation of shield supports. The new design of support has a maximum load capacity of 10,000 kN, making these units as strong as the shields used in Australia and in the USA. DMT took more than 3,100 underground observations in order to verify the roof fall frequency by statistical analysis. The results of this work have led to practical recommendations for roof control and the required shield support system on longwall faces. The underground observations have been correlated to Rock Mass Classification, to stress calculations and to the angle between the direction of the fissures and the direction of longwall mining_ The analysis work yielded the following two sets of results: 1. There is a critical distance between the canopy tip and the coal face (Tip to Face TF,n,). The TF,n, is predictable and relates to: the thickness of the first roof layer and its uniaxial compressive strength. The face support should have a TF that is less than the TFcrtt in every underground longwall situation. Exceeding the TF crit call immediately result in a roof fall. 2. Using the obtained regression equation DMT is able to calculate the probability of the roof fall frequency (FF), which describes the roof fall sensitivity. When TFcr;, is exceeded the predicted roof fall FF relates to: the measured support resistance (MSR) of the shield support the calculated vertical stress (p?) the fissure-direction index (DI = angle between main fissure direction and direction of mining) and the distance by which TFcrit is exceeded (ATF). Armed with these results DMT is now able to predict the critical distance between the tip of the canopy and the coal face (TFcrit), as well as the roof fall frequency, for all shield designs. By applying the new calculation method it is now possible to compare alternative longwall layouts and different shield support types under pre-set geological conditions. Mining engineers on site are therefore in a position to make the necessary roof control preparations required to run the longwall operation to maximum efficiency. The results provide a useful basis for making practical recommendations and for selecting the most effective design of shield support. The paper uses practical examples to demonstrate the R&D results and present the various methods now available for calculation and prediction in longwall roof control.

Jan 1, 2003

By Peng Zhang

In previous research, the laminated overburden model from the LaModel program was effectively integrated with Analysis of Retreat Mining Pillar Stability (ARMPS) through ARMPS-like input to create a laboratory version of the new ?ARMPS-LAM? program. This program takes the basic ARMPS geometric input for defining the mining plan and loading condition, and then automatically develops, grids, runs, and analyzes a full LaModel analysis of the mining geometry to output the section stability factor (SF), all without further user input. The initial ARMPS-LAM results were encouraging with a case history classification accuracy of 55% to 71%; however, a few of the input variables that were nominally included in the SF calculation showed independent significance in the classification accuracy. Therefore, in order to further improve the accuracy of the ARMPS-LAM program, an investigation of the SFs calculated by the new ARMPS-LAM program and the ARMPS program is detailed in this paper. The initial results of a linear correlation between the ARMPS-LAM SF and the ARMPS SF showed a strong correlation (R2 = 0.88), with the ARMPS-LAM SF averaging about 8% higher. The difference in SFs between the programs were further investigated, and, ultimately, the results indicated that the laminated overburden model as implemented in ARMPS-LAM distributes relatively more load on the section pillars for depths less than about 1,000 ft and less load for depths more than 1,000 ft. The results of this research highlight the potential for improving the ARMPS-LAM program in the future by implementing a more accurate loading calculation on the section pillars.

Jan 1, 2014

By Kevin Andrews, Scott Nelson, Terry Hamrick

"In the process of Geologic Hazard Mapping (GHM) for underground coal mining, geologists evaluate the effects of various geologic and geotechnical conditions to assist with optimization of mine productivity and with selection of more favorable areas for future development. The methodology involves correlation of multiple geologic factors (such as overburden depth, proximity to sandstone channels, and areas with weak immediate roof strata) with conditions encountered during mining (roof falls, floor heave, pillar spalling, etc.). Such studies yield maps that identify areas where mining is likely to be difficult and allow mining engineers to foresee favorable and unfavorable mining areas when planning new or expanding mines. To expand the benefits of GHM, work has been done to correlate geologic factors with room-and-pillar mining advance rates. Average mining advance rates are mapped and then correlated to different areas, as characterized by GHM. This process exposes the geological characteristics that have a material impact on mining rates of advance, improving the rates of advance into future mining areas with similar geological conditions. The final result of the work allows mine planners to not only design the mine qualitatively accounting for areas of unfavorable conditions, but also allows the mine planner to more accurately apply rates of advance for mine timing and production sequencing. The use of GHM to predict mining advance rates in unmined areas enhances the benefits of traditional hazard mapping and provides quantitative data that can be incorporated into mine sequencing models.INTRODUCTIONThe role of a geologist in the coal mining industry has evolved significantly over the last 30 to 40 years. Geologic Hazard Mapping (GHM) mapping for coal mines began in the late 1970s and early 1980s (Chase, Newman, and Rusnak, 2006). Since its beginnings, the GHM process has evolved significantly and continues to take on new levels of sophistication. Numerous case studies of GHM application to predict future mining conditions exist in the literature. For example, Artrip, Nelson, and Newman (1993), documents the geotechnical characterization of roof and floor for mining in the Imboden Seam in Virginia where previous mining efforts had been abandoned due to adverse mining conditions. In addition, Keim and Miller (1999) summarize evaluation of geological influences on a longwall mine in West Virginia. In both examples, significant geotechnical and geological information was available, including the opportunity to compare predicted mining conditions against actual conditions as mining progressed."

Jan 1, 2018