Search Documents

By Gabriel S. Esterhuizen

A survey of pillar conditions was carried out at 21 operating limestone mines that use the room-and-pillar method. The surveyed pillars were all located in rock that was classified as ?Good? to ?Very Good? using the RMR rock mass classification system. The average pillar width was 14.5m and the width to height ratio varied between 0.53 and 3.52. Pillar conditions were rated using a visual rating system that accounts for the effect of geological structures as well as stress related fracturing. Nine cases of pillar instability were recorded. Pillar instabilities were typically limited to individual pillars or small groups of pillars within an otherwise stable layout. Local geological structures such as inclined discontinuities or weak bedding planes contributed to instability in seven of nine cases that were observed. Elevated pillar stresses contributed to instability in the two remaining cases. All the unstable pillars observed had width-to-height ratios of less than 1.5. It is concluded that pillar instability is most likely to be caused by unfavorable geological structures in pillars with width to height ratios of less than 1.5. Stress related instability such as rib spalling becomes more prevalent when the average pillar stress approaches approximately 20 MPa.

Jan 1, 2006

In this paper a numerical formulation is presented for determination of the axial load along a cable bolt for a prescribed distribution of rock mass displacement. Results using the program CABLE indicate that during excavation, the load distribution that develops along an untensioned fully grouted cable bolt depends on three main factors: (i) the properties of the cable itself, (ii) the shear force that develops due to bond at the cable-grout interface (i.e. bond stiffness), and (iii) the distribution of rock mass displacement along the cable bolt length. In general, the effect of low modulus rock and mining induced stress decreases in reducing bond strength as determined from short embedment length tests, is reflected in the development of axial loads significantly less than the ultimate tensile capacity even for long cable bolts. However, the load distribution is also dependent on the deformation distribution in the reinforced rock mass. Higher cable bolt loads will be developed for a rock mass that behaves as a discontinuum with deformation concentrated on a few fractures, than for one which behaves as a continuum, either due to a total lack of fractures or a very high fracture density. This result suggests that the stiffness of a fully grouted cable bolt is not simply a characteristic of the bolt and grout used, but also of the deformation behavior of the ground. In other words, the same combination of bolt and grout will be stiffer if the rock behaves as a discontinuum than if it behaves as a continuum. This paper also explains the laboratory test programme used to determine the constitutive behavior of the Garford bulb and Nutcase cables bolts. Details of the test setup as well as the obtained results are summarized and discussed.

Jan 1, 1996

By Danell. R. E.

A drill monitoring system has been developed which measures performance characteristics of a rotary drill and relates this to the material strength and rotary specific energy. The drill monitor is computer based and is used to produce a profile of the relative in-situ material strength as a function of depth. This information has been used in determining the placement of explosive in selective loading of blastholes and estimating the amount of lump product in a particular section of an ore body.

Jan 1, 1989

By G. M. Molinda

Ground Penetrating Radar (GPR) is being investigated for the potential to determine roof hazards in underground mines. GPR surveys were conducted at four field sites with accompanying ground truth in order to determine the value of GPR for roof hazard detection. The resolution of the current system allows detection of gross roof fractures (>63 cm (s1/4 in) zone) or rider beds in coal measure roof. Data quality is not yet sufficient to detect small bed separations or subtle lithologic changes in the roof. Differences in data quality are discussed, as well as suggestions for collecting improved data.

Jan 1, 1996

By S. J. Jung

A fundamental study of fragment size distribution and characteristics of fracture pattern is presented for the dynamic penetration of a conical bit into coal block. In this paper, damaged zones during crater formation and fragment size distribution were studied. Bit with a sharper tip angle and a smooth body configuration performed better penetration. Results suggest that in coal cutting the trend should be toward the face cleat direction using a sharper angled tip bits which consumes less energy for an optimum range of penetration depths, thus attaining maximum cutting efficiency and reducing fine fragments.

Jan 1, 1989

By Sanjay Kumar Singh

The mechanics of load transfer in bord-and-pillar mining is not well understood despite the evolution of the art of pillar extraction over the last 20 years via trial and error (empirical) or Rock Mass Rating (RMR), simple monitoring and pillar extraction experiences at neighboring mines. Variations in geologic conditions and pillar extraction methods, along with a lack of comprehensive instrumentation programs for monitoring ground behavior during pillar recovery, are among the factors that make it difficult to predict how strata will respond to pillar extraction. Efficient and safe use of roof supports depends on the interaction between the designed support and coal strata. Of particular interest in this study is the mechanics of strata deformation as influenced by geologic conditions, pillar extraction methods and optimum support with load-bearing capabilities in strata control during mass exploitation of underground coal deposits required detailed investigation,?. To provide a better understanding of the mechanics of strata deformation, as researchers, we have collected data and reviewed measurements of convergence and stress in one mine of South Eastern Coalfields Limited (S.E.C.L.), i. e., in North Chirimiri Pondary Hills (NCPH) and have completed numerical modeling with FLAC software for (Fast Lagrangian Analysis of Continua modeling, Itasca India Consulting Pvt. Ltd.) for two typical pillar extraction plans. Stress distribution in the mine roof above pairs of roof supports was calculated to demonstrate how Resin roof bolt support installed support contributed to roof block movement control. It was shown that overall stress and roof-floor convergence patterns were most influenced by the stiffness of coal measure rocks and by pillar extraction sequences and layouts. Also, resin roof bolts and other support systems play a critical role in controlling stability of both the immediate roof and the main roof for a distance of up to 18 meters (i.e., working coal seam height X three times) above the seam. Installed supports provide unique strata control advantages over other types of secondary support by significantly reducing the time between mining and installation of the secondary support. Although resin roof bolts are similar to posts in stiffness and capacity, they are more effective than posts under static loads because they can yield and still maintain loads at nearpeak capacity(Singh, et al., 2006), whereas posts fail and lose their ability to limit mine roof deformation.

Jan 1, 2012

By Stephen C. Tadolini

PC-Strand tendons, commonly referred to as cable bolts, have become a major rock reinforcement device for underground mining and civil applications. The most common configuration is a 1+6 strand, which designates a center king-wire, with six outer wires wound around it to form a 0.6-in (15-mm) diameter cable. The capacity of this tendon approaches 30 tons, but the performance is largely dependent on the anchorage medium and the ability of the system to transfer stresses back into the rock mass while reinforcing and suspending the immediate roof. Recent developments to improve the transfer mechanisms of the PCstrand via the anchorage medium by impregnating the individual wires with uniquely designed deformations have resulted in improved anchorage and subsequent cable bolt performance. This paper describes a series of laboratory tests used to develop the initial indentation patterns and numerical modeling simulations that were undertaken to refine and optimize the final designs. The new, indented PC-Strands, offered in both bright and properly galvanized, have been tested in the field and are being used effectively in two new cable bolt products. The results of the laboratory, computer modeling, field testing and in-situ installations provide a glance at the next generation of cable bolts. This suite of testing shows how they will improve the safety and serviceability of openings under adverse ground conditions.

Jan 1, 2012

By Liane J. Terrill

Rockbolt failures at the Waste Isolation Pilot Plant have been recorded since 1990 and are categorized in terms of mode of failure. The failures are evaluated in terms of physical location of installation within the mine, local excavation geometry and stratigraphy, proximity to other excavations or shafts, and excavation age. The database of failures has revealed discrete areas of the mine containing relatively large numbers of failures. The results of metallurgical analyses and standard rockbolt load testing have generally been in agreement with the in situ evaluations.

Jan 1, 1995

By P. Tsang

The mechanisms and functions of yield pillar are analyzed by employing finite element method that takes time dependent and plastic failure of rock into consideration. The design criteria for different geological conditions are discussed. The results provide further evidences that yield pillar design will improve floor or roof condition, especially when the floor and/or roof strata are weaker than the coal. Based on this study, the yield pillar size is determined for one cod1 mine located in southern West Virginia.

Jan 1, 1989

By M. K. Larson

The U.S. Bureau of Mines conducted a study to evaluate support interaction between conventional bolts and the rib at two Western coal mines. The principal goal was to develop guidelines for designing rib support under various conditions. At mine A, seven rib bolts were installed with load cells and monitored over a 4-month period. Fifty-seven pull tests were conducted with two types of anchors at various depths. At mine B, 163 pull tests were conducted. Results showed that during the 4 months of monitoring bolt load, tension in the bolts decreased over time in some situations and that anchorage capacity was reduced in a yielded zone. Load-versus-deformation plots from pull tests in the rib showed fundamental differences in anchorage behavior at the two mines, particularly when comparing results of tests in old pillars at mine A and tests in new ribs at mine B. Numerical modeling experiments indicate that coal bonding strength was the most significant factor in determining postyield anchorage capacity. Correlation of anchor yield point with anchor depth were more pronounced at mine A than at mine B; measuring torque may be a reasonable method of monitoring deteriorating anchorage capacity in a rib undergoing fracturing and yield.

Jan 1, 1996

Appropriate roof control is the most important requirement in underground coal mining and, in the case of longwall panels or second mining in room and pillar extractions, this can be simply expressed in terms of good and predictable roof caveability. Studies of roof caveability have been undertaken in many coalfields around the world. Most of their conclusions. however, are directly related to the mining and geological conditions experienced in these areas and as a result, may not be applicable to the conditions encountered in the Appalachian coalfield. Furthermore, some of these studies appear to be theoretical and conceptual, ignoring many important parameters of the geological environment, whereas others rely heavily on geological information but lack a rigorous foundations upon which quantitative design guidelines can be built. The objective of this study is to analyze caving and mass deformation characteristics above longwall panels in Appalachia and includes: - Analysis of the effects of the geological and geomechanical characteristics of the strata on the caving height and the bulking of the caved-material. - Testing of the applicability of the various theoretical and empirical models of roof caving. Formulation of a numerical around- deformation model for ion-elastic material behavior.

Jan 1, 1986

By Gavin J. Faulkner

This paper presents an investigation of some alternatives, and improvements to timber posts and cribs. The purpose is to find a cheaper, better, easy to install, and effective means to replace or improve them. Selection of supports needs to take account of several factors. These factors include the mechanical behavior of the support, technical feasibility, and cost. In this paper a variety of supports are compared on these bases. Particular advantages and disadvantages of those supports have been determined through published material and a testing program. A broad evaluation of a number of specific groups of supports is presented. Included in this evaluation are timber posts and cribs, steel friction props and several, newer developments such as the Micon Yield Capsule and the Super Post. Another support that will be briefly discussed is steel-fiber-reinforced concrete. Particular emphasis will be placed on the Micon Yield Capsule and the Super Posts on which preliminary testing has been carried out. The testing results are presented in detail. The shortcomings of the test procedure are pointed out and some new ideas to improve the testing in the future are proposed.

Jan 1, 1986

By N. P. Kripakov

Results of a complex three-seam interaction analysis in a western U.S. coal mine are presented. The physical situation simulated by the models represents the development of a set of entries underneath two previously mined seams with all three seams in proximity to each other. The layout and the geometry of the remnant pillars in the upper seams were nonuniform and not always directly superimposed over each other, creating a very challenging modeling problem. The U.S. Bureau of Mines' MULSIM/PC computer code was upgraded and enhanced to perform the required three-seam interaction calculations. Analysis was limited to simple linear-elastic assumptions as only peak stresses were required. Results clearly indicated that stress concentrations in the lower seam increased approximately 100 percent when compared to cases simulating no extraction in the two upper seams. These stress concentrations generally occurred in zones directly below points of highest abutment pressures in the upper seams. Overall, the model results compared favorably with actual documented observed behavior where roof failures were known to have occurred.

Jan 1, 1996

By David Conover

The El Boleo Copper Project is currently in the final design stages for development of a 3-MM-tonne/yr underground copper mine located in Baja California, Mexico. The nearly horizontal mineralized zones are amenable to exploitation by conventional mechanized coal mining technology using continuous miners, shuttle cars, and belt haulage. The mine design resembles a typical full-extraction coal mining operation utilizing a sequence of mains, sub-mains and production panels. Due to numerous faults, mining will be conducted as several small adjacent mines accessed through adits from large arroyos cutting through the mine area. Up to four seams may be mined in some areas with a maximum overburden depth of about 250 m. The ore zone is relatively weak and plastic, subject to extensive creep over time. The mine workings will pass through areas of historical shortwall mining panels where the ground has flowed into old entries and gob areas, and then reconsolidated. A small test mine was developed to evaluate mechanical cutting performance, roof-bolt anchorage capacities, roof and pillar stability and caving behavior. In-mine measurements were combined with two- and three-dimensional FLAC models to evaluate alternative development and production pillar designs. The paper will discuss the various factors influencing ground stability at the El Boleo project and the strategies employed in developing a suitable ground control design.

Jan 1, 2009

By K. F. Unrug

In the paper a numerical modeling method is used for evaluation of a roof support system, which is commonly used in the US coal industry. The effectiveness of mechanical roof bolting with or without, header boards and steel straps are compared. This analysis takes into account the response of a shaly roof to changing environmental conditions in mines related to the seasonal changes in temperature and humidity of the intake air. Discussed are principles of roof support in coal mines and based on them a critical evaluation of header boards interaction with bolts and roof itself is carried out. Header boards create a soft inclusion within a much more stiffer system comprising bolt-rock. As an alternative to header boards, steel straps are analysed and corresponding results are presented. It is demonstrated that application of steel strap is beneficial from the stand point of stress distribution and maintaining tension on roof bolts. The laboratory investigations and modeling work previously undertaken by the authors, clearly indicate the detrimental effect of header boards on effectiveness of roof bolting. There are significant practical implications of the research considering that header boards are commonly used in mines. This practice has been probably originated from the wooden support used by mining in "pre-bolting era?, and it has stayed with coal mining based on tradition more than principles of engineering design. It is demonstrated that header board$ are detrimental and actually contribute to development of roof problems.

Jan 1, 1989

By John C. Stankus

Jennmar Corporation. in an effort to improve mine roof control, has conducted extensive study and research comparing tensioned point anchor resin systems versus the use of non-tensioned fully grouted rehar. Preliminary indications are showing that in thinly laminated, weak strata, tensioned point anchor resin systems are providing more effective roof control than the non-tensioned fully grouted rehar. In this paper two case studies are presented in which tensioned point anchor resin systems were utilized to stabilize and control the mine roof in two different mines. Both mines are alike in many ways, but yet very different in other aspects. However, the mines do share one main common factor. and that being the non-effectiveness of the non-tensioned fully grouted rebar in controlling the thinly lamininated strata in each respective mine.

Jan 1, 1990

By Najdat I. Aziz

There are different schools of thoughts about the influence of gas pressure on coal strength. Researchers have reached contradictory results with regard to the effect of confining gas pressure on tensile strength of coal. Accordingly, this paper re-examines the influence of gas pressure on the strength of coal. A specially designed precision drill capable of drilling in a pressurised chamber was used to drill coal samples under both atmospheric and increased gas pressure environment. The drill cuttings were examined for particle size distribution using a laser controlled Malvern Mastersizer S particle size analyser. Petrographic analysis of the sample examined the effect of gas pressures on the maceral structure and the composition of coal. The paper demonstrates that there is a definite variation in the range of particle size distribution with particles obtained from drilling coal samples not subjected to gas pressures, in comparison with those obtained from samples drilled under confined gas pressure. Also observed were the changes in the rate of drilling in soft coal obtained from geologically-disturbed zones compared with other coal samples. Some variation on the maceral compostion of coals were also observed in relation to increased gas pressures and gas type.

Jan 1, 1996

By D. S. Choi

This paper presents a theoretical analysis of the effect of shape and size on strength of geologic materials. The results indicate that the shape effect is caused by the development of confining pressure at the interfaces. The linearization of the obtained formula is of the same form determined by experiments. The size effect is attributed to the fact that the geologic materials contain discontinuities in the form of fractures, bedding planes, and cleats. The maximum reduction factor for the size effect is the one-sixth power of the volume of a cubic test specimen. The results of this work are particularly useful in determining the strength of coal pillars in underground mines.

Jan 1, 1989

By Y. H. Wang

During the last two decades many research projects were conducted to study the load requirements for the powered supported longwall faces (1-6). Significant results had been achieved by these researches. Most of the previous studies were rarely designed to understand the mechanisms of interaction between the supports and the surrounding rock, or to correlate the stress conditions around longwall faces to the mining operations both in time and space. In case of the shield supported faces, the roof-to-floor convergence is very difficult to measure due to the high percentage of roof coverage. The external load on the supports can not be determined from the leg pressure data alone due to the existence of the lemniscate links. Therefore, there is a real need in that a simple engineering method be developed to monitor the variations of roof load on the shield supports, the roof-to-floor convergence and the roof stress restoration in the gob area as the mining proceeds. Only with the results of these measurements, a further understanding about the mechanisms of interaction between the supports and the surrounding rock can be achieved and a criterion of designing or selecting the optimum mechanical parameters of the shield supports can finally be developed.

Jan 1, 1986

By Gilles Rousset

This paper presents laboratory experiments conducted on hollow cylinders samples. The advantage of such a geometry is to approach in situ conditions around cylindrical openings (lined galleries, boreholes, ...). Many authors have been interested in this kind of problem, especially for borehole stability applications (for references see Guenot 1987). However, as long as we know, time-dependent behavior has not been well studied. For this purpose, we have set up two different types of tests on a deep clay : - Quick unloading test, to assess the influence of unloading rate on mechanical response and the failure modes. - Creep and relaxation test, to compute the time dependent overall deformation of the hole wall as well as to plot long term convergence-confinement pressure curve. The experimental results are then compared with those given by a theoretical model developed in our laboratory, well fitted with the tested material.

Jan 1, 1989