Search Documents

By K. Vanbroekhoven

An industrial site near the centre of a historical town in Flanders is characterized by chromium(VI) contamination of the groundwater. Since the potential for natural attenuation was not sufficient to control the groundwater plume as observed from different analyses like pH, Eh, soil oxidation and reduction capacity, the feasibility of site remediation based on in-situ bioprecipitation of chromium was examined in lab microcosm studies. By creating reducing conditions by addition of a carbon source in the groundwater, chromium(VI) can be biologically reduced to chromium(III), which can form an insoluble precipitate of chromium(III) hydroxide. Microcosms contained contaminated groundwater and aquifer samples that were collected and manipulated under anaerobic conditions. Three different carbon sources were screened for their effectiveness: molasses from sugar beet production, molasses form starch production (protamylasses) based on potato juice and lactate. The different concentrations of sugar molasses were used to determine the optimal conditions. A range of parameters was monitored at regular time intervals for a period of six months such as chromium(VI) and chromium(III), DOC, methane, pH, Eh. A rapid conversion of chromium(VI) to chromium(III) was observed for all conditions tested. However, extensive removal of chromium from the groundwater by precipitation was only achieved for a limited number of conditions. In general, lactate was found to be the most effective carbon source, slightly better than the lowest concentration of sugar molasses that was tested, which itself was more effective than molasses based on potato. Higher concentrations of molasses, although causing a steeper decline in redox potential, resulted in less effective Cr removal. Typically, the fermentation of molasses results in acidification and this drop in pH may hinder the formation of insoluble chromium(III)hydroxides. It may also be possible that certain components of the molasses form soluble complexes with chromium(III). For lactate, no significant drop in pH was observed. Following the laboratory microcosm tests, the stability of the chromium precipitates was examined by performing a sequential extraction on the microcosm materials. These were performed under redox conditions which were similar to the ones observed in the field. Since the outcome of these tests was positive, a pilot scale test was implemented in the field in April 2005. Two different substrates, the cheap waste product sugar molasses and lactate are being injected creating two different impact zones and typical parameters are monitored. Frequent re-injections were important to maintain reduced conditions and are carried out three-weekly up to now. To study the stability of precipitates formed, mesocosm socks containing aquifer material were installed in the monitoring wells and harvested at regular intervals. Results of this pilot test will be presented and compared to the laboratory results. Based on the success of this field test, a full scale process will be designed and implemented as remediation strategy.

Jan 1, 2006

By Alan R. Grant

Interpretation of presently available geological information indicates that most of the periods of significant metal deposition in the Washington Cascades Range are, at least in part, genetically related to late Cretaceous -Tertiary intrusive episodes. Chemically, the most favorable environment for base metal deposition is high in potassium. Characterizing the advanced stages of these chemical alteration conditions are the silicate mineral assemblages orthoclase and/or secondary biotite. Wall rock alteration includes both deuteric and hydrothermal processes, the intensity of which primarily depends upon the degree of fracturing in the country rock prior to the introduction of secondary material. Broadly speaking, the primary physical controls for the distribution and concentration of sulfides appear to be a series of structural couples involving both northwest (paralleling regional trends) and northeast--striking systems. Meaningful base metal exploration in the Washington Cascades demands a basic understanding of the various geologic factors related to the distribution of the sulfide deposits. Any geologist contemplating Cascade work should be well grounded in the fundamental concepts of petrology and structure.as these constitute two of his most beneficial aids. The acquisition of the detailed data necessary for this understanding may seem a bit academic, yet it has been demonstrated in numerous instances that a fair economic appraisal of a particular property or mining district depends primarily upon the ability of the geologist to recognize the subtle environmental differences which could lead to the discovery of a major ore deposit.

Jan 1, 1971

By W. Kuckshinrichs

Metallic raw material flows are characterized by a complex global network of producers and consumers, as well as by a multitude of ecological, economic and social impacts across national boundaries and on different scales. This leads to the need to develop methodologies, which allow identifying obstacles that prevent metallic raw material flows to contribute to sustainable development. From a scientific point of view CRC 525 (Martens 2003) has developed an holistic indicator set consisting of approximately 80 different indicators. This set is taking into account the multi-dimensional character of sustainable development. Moreover the indicators reflect different system boundaries according to different actor levels and decision contexts. The full indicator set is important in scientific considerations and suitable for scientific awareness creation. However, to fulfil the function of a decision support approach for political and economic decision-makers some modifications are of central concern. At first a reduction of the full indicator set by selection of core indicators enables decision-makers to deal with complex issues of contrary economic and societal protection targets. Secondly, as thresholds of indicators justify societal call for action, they are discussed against its political or scientific origin. The proposed methodology is exemplified by indicator-based studies of the material flow of aluminium.

Jan 1, 2003

By J. C. Willett, J. R. Sanfilipo, S. M. Podwysocki, P. D. Warwick

The U.S. Geological Survey is concluding an assessment of the major coal regions of the country. In this program, the quantity and quality of coals that are expected to be mined during the next 30 years are characterized. For the Gulf Coast region, the evaluation includes reviews of the stratigraphic setting, coal resources, and the quality of the Cretaceous to Eocene coals in four coal-producing areas. The coal-bed methane potential for these areas will also be evaluated. The results of these efforts will be a series of digital maps, text, and tables that will be published in a CD-ROM format.

Jan 1, 2000

By P. Riveros, J. Binvignat, V. M. McNamara, D. Koren

The feasibility of recovering cyanide and copper from a gold mill barren solution was evaluated in a small A VR pilot plant. The campaign lasted 64 hours, during which time about 4,000 L of gold mill barren solution were processed. The results showed that A VR is an effective technology for recovering cyanide and copper from barren solutions. Under the best conditions, the copper precipitation and the cyanide volatilization attained 94% and 98%, respectively. Using 5 MNaOH as the absorbent, practically all the HCN gas was recovered in the form of a concentrated NaCN solution containing 70 g/L free CN. Basic engineering design parameters applicable to a large-scale operation were obtained, including the Henry's Law constant and the mass transfer coefficient for HCN gas.

Jan 1, 1997

By F. Ferella

In this paper several leaching tests were per-formed to optimize the leaching section of a hydrometallurgical process for the recycling of alkaline and zinc-carbon batteries. Zinc and manganese oxides were dissolved by an acidic-reductive leaching using sulphuric acid and oxalic acid as reductant. Leaching tests were developed according to a full factorial design. The operational variables were pulp percentage, sulphuric acid concentration, temperature and oxalic acid concentration. Additional tests were performed to evaluate the precipitation rate of Mn and Zn oxalates. Finally a hydrometallurgical process were proposed for the recycling of alkaline and zinc-carbon batteries, in which Zn and MnO2 are recovered from purified solution by electrowinning: Zn is recovered as metallic compound, while Mn can be recovered as electrolytic manganese dioxide (EMD), but recovery of further manganese compounds is possible with simple process changes.

Jan 1, 2006

By J. F. T. Agapito, C. E. Brechtel, M. E. Adam

Full-scale stopping and simulated over- cast structures were constructed in large opening (30 ft high by 55 ft wide) room and pillar excavations in an oil shale mine. The program was undertaken to develop construction techniques and to generate data on structure costs and leakage rates. Leakage rates were measured using both sulfur hexafluoride tracer gas and "brattice window" methods at varying differential pressures. The measurements were conducted before and after a full-scale face blast to characterize the effects of blasting on leakage, and blast air pressures were measured across the stoppings. The operating performance of different combinations of permanent and temporary stoppings was evaluated by developing an operating model for a two-panel oil shale mine. The operating performance for the different stopping combinations was then compared to the system cost to evaluate the overall performance.

Jan 1, 1987

By Rick Sarkisian, Albert D. Bonneau, David Keech

The Drummond Co. Inc.'s Shoal Creek Coal Mine Slope Belt Conveyor transports 5000 mtph (5500 tph) of material over a length of 1400 m (4600 ft.) and a lift of 3609 m (1180 ft.). Four 1500 kW (2000 hp) motors power the 1830 mm (72 in.) Goodyear Flexsteel 5800 steel cable belt. In May 1993, Dodge Manufacturing was selected to design and build the conveyor pulley assemblies for this conveyor. The conveyor includes five pulley assemblies. The 2135 mm (84 in.) diameter by 2135 mm (84 in.) face primary and secondary drive pulleys were designed for a resultant belt load of 3060 kN (688,000 Ib.) This paper describes the design and manufacture of the two drive pulley assemblies. Design details included are component evaluation, material selection, locking assembly selection, bearing selection and lagging selection. Manufacturing details include material procurement, welding process, lagging installation and component assembly. Quality control procedures are also discussed.

Jan 1, 1996

By Yoshiak Mizuta, Hi Keu Lee

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the authors elect, they may distribute copies at the time of the Symposium

Jan 1, 1986

By A. Shtiza

This literature review discusses the role of the Albanian institutions, the natural resources industry, potential investors and stakeholders in order to provide a set of indicators that can help to monitor amelioration within sustainable development principles. A map with the potential prospects of the natural resources will be a first step in identifying the further potential for exploitation. Mineral resource policies and governance, sustainable processing and supply chain as well as environmental management information system are some of the crucial tools identified, that will help to set up the indicators and quantify the achievements in environmental management in Albania. Moreover, the integration of practices that will support institutional capacity building; follow-up practices; the mainstreaming of global environment into planning; and the compliance monitoring process will additionally improve the environmental situation in Albania. Aligning business strategy with environmental policy, socio-economic analysis, environmental auditing are decisive tools in order to provide the Albanian authorities with a clear overview of the economic costs and the social benefits for sustainable development.

Jan 1, 2011

By Richard Kolada

If the emission of methane into any particular area of an underground coal mine remains constant, then the calculation of ventilation requirements is relatively simple. This is also true if the ventilation system is recirculatory. However, the emission of methane into a working area can vary considerably. There is always a risk that the ventilation will not be able to dilute the emission of methane to acceptable levels, because there are often short-lived peaks of emission which are very large. The ventilation design must therefore consider what is an acceptable level of risks and calculate the airflow requirements to meet this level. The acceptable level of risk can be calculated by examining the historical variation in methane emission into the area to be ventilated. For example, consider that an acceptable level occurs when methane emission peaks only exceed the capability of the ventilation one day in twenty. Then, from the history of methane emission, it is possible to calculate the necessary ventilation requirements. This method has been used since the early 1980s for conventionally ventilated districts. This paper examines the application of this technique to districts ventilated by recirculatory ventilation.

Jan 1, 1987

By J. W. Leonard, D. A. Newman

By using physical and chemical means to increase the bulk density of newly broken coal freed from the mine face, the potential to improve coal mine productivity is significantly enhanced. It is estimated that by increasing bulk density, greater tonnages can be placed in fixed volume scoops and shuttles cars to improve production by as much as 10% to 20%. Such improved packaging to achieve new levels of volumetric efficiency might require only small and easy to implement changes to present downstream mining operations. Opportunities exist for improving broken coal bulk density from the moment of breakage, during transport across the continuous miner or loading machine, during discharge into the haulage unit, and after placement in the haulage unit. Physical/chemical methods for broken coal compaction in mobile, fixed volume units in underground operations are discussed.

Jan 1, 1990

By Larry DeGraff

With the increase of new mine development in the past several years, many coal mines have decided to self- perform the design and construction for their slope development projects. The development process of determining the proper configuration is challenging, and a major economical consideration. Greenbrier Smokeless Minerals engineering staff and consultants, along with DSI/American Commercial, developed a support configuration that was best suited for their slope. The developmental process took into consideration the length of slope, depth of slope at the high-wall transition, economics of a single or multiple entries, waterproofing, stresses on the steel supports and lagging during the backfilling operation. This paper describes the developmental concept of using a single entry, side by side configuration, using steel ?Banjo String? supports with steel plank lagging, to develop a long term permanent installation in a cut and cover application.

Jan 1, 2009

By J. A. Eisele, G. E. McClelland, M. D. Wroblewski

The Bureau of Mines is conducting research at its Reno Research Center to develop a staged agglomeration-heap leaching system and to electrowin the dissolved precious metals from the pregnant leaching solution. For direct electro- winning to be successful, the pregnant solutions generated during the Initial stages of leaching must be higher grade than obtained by conventional heap leaching. The precious metal concentration of the pregnant solution can be Increased by agglomeration pretreatment with cyanide solution which starts the leaching process during the curing period, by leaching with small volumes of solution and by cycling the leaching solution through more than one heap in a staged manner. The resulting pregnant solution is passed directly through an electrowinning circuit. The barren solution from electrowinning is recycled to the leaching circuit. Bench-scale research on the development of the staged leaching system and on the development of an efficient electrowinning cell are described. The Bureau of Mines developed agglomeration- heap leaching technology. This technology was readily adopted by the mining Industry for heap leaching crushed ores and mine wastes. Current research involves the application of this technology to finely ground feed materials such as precious metal-bearing milled tailings. Tailings agglomeration-heap leaching has also been used commercially.

Jan 1, 1984

By P. T. Perdue, F. F. Haywood

INTRODUCTION Monitoring devices used for detecting and measuring airborne radon in mines are limited due to the rugged environment in which they must operate. Personnel monitors now available are either passive or require filters and an air pump. Area air monitors usually have bulky batteries or require electric power service to the instrument. Thus, there are few instruments presently in use in mines capable of discriminating between the various radon isotopes and their daughters. Occasionally it is desirable to determine which radon daughters are the principal dose contributors in mine air. In some areas, such as the Elliot Lake mine in Canada, there exist sizable quantities of 220Rn in the mine air due to 232Th in the ore (Cote and Townsend, 1981). Since there has been recent interest in radon daughters in homes and factories, as well as caves and mines, methods and instrumentation are being developed to address these cases. Some of these methods can be employed in uranium mines. Although there have been very few determinations of the three radon isotopes (222Rn, 220Rn, and 219Rn) and their daughters made in uranium mines, these isotopes have been measured in process buildings and in private homes under circumstances that suggest these isotopes could also be present in uranium mine air (Perdue, Leggett, and Haywood, 1980; Yarborough, 1980) METHODS Cryogenic air sampling was developed about 15 years ago (Rasmussen, 1972) to concentrate various airborne chemicals for later fractional distillation and measurement of various organics using gas chromatography. A version of this technique has been developed to measure tritium, krypton, and other radioactive gases in nuclear power station buildings (Anon, 1980). In this method, fractional distillation is used in conjunction with various detectors to identify the radionuclides present. The cryogenic method to be discussed here was developed at Oak Ridge National Laboratory (ORNL). It uses the liquid air accumulated in a sampling device for a direct analysis of all gamma-ray emitters present. The air sampler (Fig. 1) could be employed in a mine to liquefy air, using the difference between the point of liquefaction of air (~80 deg. Kelvin) and the boiling point of liquid nitrogen (77 deg. Kelvin) to liquefy an air sample. By using a proper orifice at the entry to the sampling vessel, air of any dust concentration and relative humidity [ ] may be sampled. The energy for sampling is provided by the slow evaporation of the liquid nitrogen; no other power source is required. This type of sampler could be used to augment the usual filter and pump, or passive system presently employed to estimate personnel dose from radon daughters. It would also allow measurement of any combination of daughters from the three radon isotopes. Upon completion of sampling, the sampler is closed and removed from the mine. This sampler, with its liquid air contents maintained by the slow evaporation of liquid nitrogen, is taken to the place of measurement. There, the sampler is opened, the accumulation of water and ice in the neck is chiseled down into the liquid air, and the sample is transferred quickly to a precooled counting dewar (Fig. 2). This counting dewar is then placed upon a gamma radiation detector; we recommend a high purity germanium detector. A determination of all the radon daughters can be made in 1 to 4 hours after the sample is taken.

Jan 1, 1981

By J. C. Cawley

Improvements in today's maintenance practices are mandatory as more complex and productive machines evolve in the mining industry. By keeping machine reliability high, through improved maintenance procedures, overall mining costs can be reduced. The Bureau of Mines is investigating diagnostic maintenance systems for underground mining machinery. A hydraulic expert diagnostic system and an electric motor predictive diagnostic system have been designed and installed on a Joy 16CM continuous miner. An electrical diagnostic system has been designed and installed on a Joy 14CM continuous miner. Each system is functionally described and the relative merits of expert diagnostic systems versus algorithmic diagnostic systems are discussed.

Jan 1, 1991

By R. A. Jankowski, J. J. McClelland

Laboratory tests were conducted by the U.S. Bureau of Mines to determine the respirable dust reduction effectiveness of and interaction between face airflow and water sprays for a continuous miner. Exhausting face ventilation was varied from 3,000 to 9,000 cfm (1.42 to 4.25 m3/sec). Spray-water-flow was varied from 15 to 35 gpm (0.057 to 0.132 m3/min), while nozzle operating pressure was varied from 80 to 200 psi (5.62 to 14.06 kg/cm2). Results from gravimetric dust samples indicated that airflow had the greatest individual impact on reducing dust levels, with return and operator concentrations reduced by as much as 57% and 99%, respectively. Interactions between dust control parameters were found to be significant. Often, these interactions defined a level of application for a control parameter where further increases in that parameter failed to produce additional reductions in dust concentrations. In several cases, increases in a control parameter resulted in higher dust levels at the operator's location. These higher dust levels were attributed to additional rollback and/or airflow turbulence. Regression modeling indicated that increases in airflow to 8,400 cfm (3.96 m3/sec), water flow to 25 gpm (0.095 m3/min), and water pressure to 140 psi (9.84 kg/cm2) typically were beneficial at the operator and return sampling locations.

Jan 1, 1991

By H. Singh

Principal source of rhenium is molybdenite. Depending on the mineral processing route, rhenium can be recovered by one of the several alternative solvent extraction processes. Extensive experimental work has been carried out on the development of tertiary amine extraction process for treating very dilute highly impure scrub solutions obtained during scrubbing flue-gases of molybdenite oxidative roasting. Equilibrium data has been obtained under various process conditions by tracer analysis using radioactive Re-186. Extraction with 1% solution of a high molecular weight tertiary amine in kerosene, followed by scrubbing of organic extract with a solution of sulphuric acid and stripping with ammoniacal ammonium sulphate yields high recovery, concentration, and purification.

Jan 1, 1982

By John D. Kalasky

Island Creek Coal Company has had, for many years as a primary concern, the activity of handling large quantities of methane in the ventilation of its deep mines of southwest Virginia. Since the development of the Beatrice operation in the mid 19601s, the concern has been well founded, and through the years progress has been made in this most important facet of the extraction of the coal reserves to insure the safety of the employees engaged in the mining opera- t ions.

Jan 1, 1980

By Simon T. Johnson, Robert J. Fowell

The application of roadheading and drag tool equipped machines requires an assessment of both cutting performance and tool consumption. Neither parameter can be assessed purely from compressive strength and tool consumption is often neglected, at a cost to the project. Results from in-situ monitoring show that a measurement of relative abrasivity using the Cercharscratch abrasivity test provides a basis for the assessment of tool consumption. This can be modified by also considering the effects of the machine specification and the rock mass quality.

Jan 1, 1986