Search Documents

By D. L. Passmore

The development of microcomputer software that provides an analysis of pit-specific accident and production data for the mining industry is seen as a vital component in a total loss-control system. The Mine Injury Reporting System (MIRS) allows users to access accident and production data prepared by the Health and Safety Technology Center of the Mine Safety and Health Administration of the United States Department of Labor for any particular state and to generate a simple, yet informative, report.

Jan 1, 1988

By S. D. Thompson, L. Adler

Several researchers in the last 20 years have developed computer simulation models for designing coal mine belt systems. A careful review of these reveals that each omitted or oversimplified important factors, especially in belt loading. To remedy this, the coal mine belt capacity simulator (CMBCS) was developed to include various types of probability distributions, delays, and longwall and continuous haulage. CMBCS is computer coded in FORTRAN and employs the Monte Carlo simulation technique. Basically, the model simulates the loading and corresponding flow of coal through a belt system. By recording spillage and belt stoppage statistics for the simulated flow, belt and surge bin capacities can be evaluated. A complete user's guide is available. The modeling and verification of CMBCS are briefly described, and its major advantages and disadvantages are explored.

Jan 1, 1987

Teeter-bed (i.e., hindered-bed) separators are used throughout the mineral processing industry for both classification and density separation. The high capacity and sizing characteristics of these units make them ideal for feed preparation prior to coarse flotation (+0.100 mm) circuits. Teeter-bed separators are typically easy to control with two basic operating parameters including fluidization water rate and bed level. However, data show that these two parameters greatly interact with one another. Given this finding, a high-level automatic control scheme was developed and implemented on a full-scale separator. In addition, dialogue with plant operators has led to several simple changes to an already established design that improves operational and maintenance characteristics.

Jan 1, 2010

By W. Dan Hausel

In previous reports by Hausel et. al., (1979 a, b, and c), Leighton and McCallum (1979), and McCallum (1974;1979), several exploration procedures were examined as to their effectiveness in locating kimberlite intrusives in northern Colorado and southeastern Wyoming, where approximately 90 kimberlites have been recognized within 5 districts (Figure I). Briefly, geological mapping and stream sediment sampling for indic- ative heavy minerals of kimberlite (pyrope garnet, chrome diopside, and magnesian ilmenite) proved to be the two most effective methods in isolating kimberlite occurrences within the granitic terrain of Colorado and Wyoming (Hausel et. al., 1979 a, b, and c; Leighton and McCallum, 1979). Where a kimberlite intrusive is deeply weathered, remote sensing using color and color infrared aerial photography may be a potential reconnaissance tool in kimberlite exploration. The kimberlitic eluvium supports thicker grassy vegetation, and at least one species of grass (the Bluebunch Wheatgrass) is found to grow only within the eluvium. The result is that vegetation in the kimberlitic eluvium is a better infrared reflector than the vegetation in the surrounding granitic soils (Hausel et. al., 1979 b; McCallum, 1974

Jan 1, 1980

By Carl-Eric Dr. Nilsson

Energy cost for mine ventilation in Sweden is high, especially during winter time when air must be heated. This paper presents the result from a project entitled ventilation-as-required. The term ventilation-as-required means that the required volume of fresh air should be distributed only to such areas, where mining work is going on and to be reduced to a minimum in the rest of the mine. Ventilation-as-required is a monitoring system that controls the operation and capacity of the fans and measure the air pollutant gases, i.e. carbon monoxide, nitrogen and sulphur dioxide at strategic points. It is an active system that responds when equipment is under operation. MITU proposed in 1991 a project to develop a ventiation-as¬required system and such components as transmitters and receivers for the communication between the equipment and the fans. The mining companies, Boliden Mineral AB, LKAB, Outokumpu and Ammeberg Mining Corporation joined the project and have financed a joint research and development programme supported with a grant from the Swedish Government through NUTEK. MITU proposed a second project in 1992 to the mining companies to develop an improved "intelligent" fan for scope ventilation. Boliden Mineral and LKAB joined the project and have financed a joint research and development project supported by the Swedish Government through NUTEK. The Government even made a commitment to support the investment of the first 50 fans ordered with a grant of 25% of the investment cost. The result from projects show that the target set up in the plans is more than achieved, with an energy reduction that exceeds 30% compared to previous consumption. No environmental influence due to reduced ventilation is observed in the stope when work is under progress. Dilution of exhaust gases from diesel fuel decreased from 6.000 m3/L consumed diesel fuels to 3,600 m3/L. The automatic data processing and sensor system is even increasing the security of the work so that it can be done under safer environmental conditions.

Jan 1, 1995

By George J. Dvorznak, Robert W. Waytulonis

The Bureau of Mines is conducting a research project in cooperation with the Mine Safety and Health Administration (MSHA). Mining companies, and equipment manufacturers are also participating through the Colorado Mining Association (CMA). The objectives of this cooperative research project are to determine the practicality of coupling a dry exhaust conditioning system (dry system) and diesel particulate filter (DPF) to make an integrated control system, and to determine the effectiveness and durability of the integrated system in an underground coal mine. Diesel-powered mining machines must be equipped with control devices to reduce surface and exhaust temperatures to safe levels and prevent flames and sparks from being emitted to the mine atmosphere. Diesel exhaust-gas water scrubbers have been successfully used for many years but they have several disadvantages; they are large, consume large quantities of water, and require frequent maintenance to remain functional. Additionally, diesel exhaust is a source of noxious gases and particulate matter. Particulate emissions are composed primarily of small carbon particles with absorbed hydrocarbons and they are almost entirely respirable in size. Even an engine in good mechanical condition can emit up to 400 mg/cu m of respirable particulate matter. A dry system for control of diesel fire and explosion hazards, coupled to a DPF, promises to be a complete control system for diesel engines. The dry system cools the exhaust and suppresses sparks and flame with a heat exchanger and flame and spark traps. The conditioner is smaller, consumes no water, and requires less maintenance than a comparable water scrubber. The DPF uses a ceramic substrate as a wall-flow filter and is very efficient at collecting exhaust particles. Average particulate mass collection efficiency is 90%. This report describes a cooperative research project to combine the dry system with the DPF, conduct performance tests on the integrated system at Bureau and MSHA 1aboratory facilities, and conduct field tests of the system on a production machine in an underground coal mine.

Jan 1, 1987

By Merline W. Van Dyke

The Surface Mining and Reclamation Act of 1977, PL 95-87 (The Act) granted the Office of Surface Mining (OSM) the duty of collecting fees from the active coal mining activities to be used in abating the hazards associated with abandoned coal mines. Since the passage of the Act, OSM has been instrumental in closing a multiple of mine hazards and in full cooperation with the states involved. Complete mine closures range from simply filling a subsidence hole to exodic designs costing thousands of dollars, such as in the case of the Portal Park swimming pool in Colorado Springs, Colorado. The Portal Park olympic sized swimming pool was built over an abandoned coal mine by a group of local citizens and given to the city of Colorado Springs. This pool receives the largest number of users each year. During the past four years, OSM has abated six mine related hazards in and around the pool. During the summer of 1982, the pool started tipping causing the pool waters to run out the west end. This pool tipping and the associated cave-in problems caused great concern to the city and the local users. This citizens concern generated a request from the city for OSM to assist in checking out the pool problems. Early in 1983, OSM initiated a driling program to investigate the subsurface voids. This drilling effort revealed several large voids within a few feet of the pool deck, with all voids inundated with ground water. Therefore, the void filling method favored the hydraulic backfilling needed to be confined to the area under the pool. This confining problem lead to the development of the gravel bulkhead cutoff walls to confine the backfilling effort to the areas under the swimming pool.

Jan 1, 1985

By Jane Morrison

Permanent magnets are used in most electromechanical and electronic devices to convert electrical to mechanical energy and vice versa. More than fifty are commonly found in the average American home and car. A new species of permanent magnet composed of iron, neodymium, and boron has recently been developed which combines superior magnetic properties with compact size. The reduced size of the magnets has enabled significant new developments in such areas as robotics and consumer electronic, among others. The objective of the present work is to efficiently and economically separate valuable rare earth materials from the relatively worthless iron constituent in NdFeB magnet scrap. Several magnet producers have expressed interest in the development of such a process and have provided information and scrap samples to aid in research. Scrap is generated in a variety of forms from different stages in the processing stream. Pieces of magnetic and non-magnetic metal as well as sludge and ribbon from jet casting must all be treated. Beneficiation techniques have been studied and size distributions developed for the different scrap types. Slag from the casting process is resistant to crushing and may need to be embrittled first, but all other types are amenable to crushing and ball mill grinding using stainless steel balls and water. Tabling was found to be useful in classification of magnet sludge. Two major techniques for separation of rare earths have been studied:

Jan 1, 1990

The Chinese city of Shanghai is one of the fastest growing in the world. To keep up with the growth, two tunnels, three-lanes each, are being built beneath the Yangtze River to connect Shanghai with the Changxing River Island. To complete such a large project, Herrenknecht Tunneling Systems was brought in to construct the largest tunnel boring machine (TBM) in the world. The first Herrenknecht S-317 Mixshield has a diameter of 15.43 m (50.62 ft). It was built to construct one of the two 7.2-km (4.5-mile) tunnels. The tunnels are part of the Changjiang Under River Tunnel Project and will be at depths of up to 65 m (213 ft) beneath the Yangtze River in Shanghai-Pudong. These two tunnels are to be opened to traffic in April 2010, in time for Shanghai to host the World Expo. More than 20 million people live in the Shanghai area. The area itself has been growing at an extremely rapid pace for more than a decade and is in need of more space. The search extended beyond the natural limits of the Yangtze River Delta. As part of its incredible growth, 500 new vehicles are registered every day. The new tunnels will connect the Changxing River Island, with a population of approximately 600,000 people to the road traffic network. A bridge construction will also provide a traffic link between Changxing Island and the large island of Chongming.

Jan 1, 2007

By Harold Wagner, Prakash Donde, Larry H. Heflin

INTRODUCTION The Washington Metropolitan Area Transit Authority is responsible for the planned 166 kilometer (103 mile) Metro rapid rail transit system in Washington, D.C. Some 117 kilometers (72.8 miles) of this system is in operation and contains 30.6 route-kilometers (19 miles) of rock tunneling. To complete the planned system an additional 1.6 kilometers (1.0 miles) of single track tunnels in rock are planned and additional contracts will consist of 4 kilometers (2.5 miles) of twin tunnel, resulting in 8 additional linear kilometers (5 miles) of single track tunnel contracts yet to be offered in soft ground. Three recent contracts in soft ground included the New Austrian Tunneling Method (NATM), along with conventional tunneling, as a bid option. Section E5a, Fort Totten Station and Tunnels, was the only one of the three to be constructed using the NATM option. This is the first application of the New Austrian Tunneling Method in soft ground in the United States. This paper will concentrate on the Fort Totten Station chamber NATM design, construction, and the instrumentation readings and evaluations which lead to an engineering back analysis which allowed a refinement of the bid design, resulting in a faster, more efficient construction. Design of the Fort Totten Station and Lines was done by Sheladia Associates. The design team included Greiner Engineering and Jenny Engineering with Mayreder-Consult of Austria, who was responsible for NATM design and NATM construction consultation.

Jan 1, 1991

By J. Villeneuve, G. Fourniguet

Simulation of Mineral Processes is now commonly used by the Engineers in charge of plant design or optimization but a good knowledge of the simulation tool is still needed to conduct a project. A new level of algorithm has been defined above the simulator to answer directly to the user's questions. This level has been called the supervisor of simulation, which is using the automation concepts of sensors and actuators. At any place of the flowsheet (i.e., a stream or an equipment), the user may indicate which value could change by graphically implementing an actuator. Then, he can evaluate the effect of the variation of this value at any other place of the flowsheet by inserting a sensor. Thus, by example, it becomes possible to look at the evolution of the recoveries and/or the circulating loads when scanning an interval of the possible teed flowrates. This approach conducts to an increased facility in using a simulator and in analyzing the predictions. It is also a very valuable tool for permitting to characterize the sensibility of the simulation results to the variation of some settings (e.g., load of grinding media, rotation speed, water addition, etc.) or feed characteristics (e.g., flowrate, sizes, grades, grindability, etc.). Thus, the most important variables can be identified for design and pre-control optimization of plants. This new level of simulation will be implemented in a further version of the USIM PAC simulator and selected examples are presented.

Jan 1, 1995

By E. (Walt) van Walsum

The MPTM was first applied in the U.S.A. in 1950 as described by Lewis, W.E., 1951. The method was then abandoned in the USA and rediscovered some 20 years later in France where it was greatly improved and widened in its scope of application. It was subsequently successfully introduced to Italy and Spain. The technique, at its present stage of development, provides solutions to tunneling in soil and in the softer rock types, which often were troublesome geological environments for tunneling. When used in conjunction with drilling-and-blasting, over break, excessive vibration, noise and fissuring of the rock can all be avoided. When used as an alternative to the New Austrian Tunneling Method (NATM), the MPTM provides safe, full face tunneling in stead of multiple headings, excavated sequentially; in addition, surface settlement can be virtually eliminated. When used as an alternative to a TBM, the method's flexibility and low capital cost make it attractive. This attractiveness is enhanced when ground conditions are erratic or when the length of tunnel to be excavated is limited. The method holds promise for tunnels of large cross section, to be excavated in soft ground or rock with unconfined compressive strengths of less than 80 MPa (11 600 psi). While in itself not new, recognition and development of the method's potential are. Further development work, aimed at increasing the range over which the MPTM can be applied, is in progress.

Jan 1, 1993

By R. C. Klimpel

Size reduction of material in aqueous pulps by the use of tumbling media overflow discharge mills is an important and common unit operation in industry. There also has been extensive attention given in recent decades on developing a more fundamental understanding of the breakage processes involved, especially in ball mills. These studies have mostly emphasized the use of size-mass balance or population balance approaches for quantifying the analysis and design of size reduction circuits, ego Austin, et al (1984).

Jan 1, 1989

By D. A. Norrgran, J. A. Marin

Introduction The recent development of rare earth permanent magnets has revolutionized the field of magnetic separation. The advent of rare earth permanent magnets in the 1980s provided a magnetic product that was an order of magnitude stronger than that conventional ferrite magnets. This allowed for the design of high-intensity magnetic circuits that operated energy free and that surpassed electromagnets in the strength and effectiveness. New applications and design concepts that focused on the mineral and metal processing industries have evolved. This technology led to the development of various magnetic separators specifically designed for mineral processing applications. Applications that were not previously considered are now being used in primary mineral upgrading, recycling and secondary recovery. Historical perspective Lodestone was the first naturally occurring permanent magnetic material known. Lodstone was most likely used to upgrade iron ore by early civilizations. By the 1600s, the early magnet technology had advanced to quench-hardened iron-carbon alloys. The practical significance of magnetic separation was formally recognized in 1792 when an English patent was issued for separating iron ore by magnetic attraction. By today's standards, carbon steel is a very poor magnet material. It is easily demagnetized and has a very low energy product of much less than I MGOe (Million-Gauss-Oerstads). This was state-of-the-art technology for almost 300 years until chromium was added to magnet feedstock, which resulted in a three-fold increase in the energy product. The well documented addition of cobalt to permanent magnets in 1917 initiated the 30-year era of "Alnico" magnets that at the time provided a superior magnetic energy product. Since then, the science of magnetism has advanced rapidly and is now considered a highly developed branch of physics and material science. Permanent magnets have had an extremely long history. Figure 1 presents a chronology of permanent magnets that illustrates the increase in energy product. Amazing developments in material science have taken place in the last two decades. The gradual advancement of permanent magnet technology was shattered in 1967 with the initial development of samarium-cobalt (rare earth) magnets. Since that time, the advent of neodymium-boron-iron magnets provided such an increase in energy product that new design concepts were considered. New avenues of study were introduced by the complexities in the material science and physics involved in describing these new permanent magnets. Furthermore, applications for permanent magnets that were previously not considered were now viable. Rare earth elements Rare earth elements have claimed the attention of scientists for the past century. These elements were originally termed "rare" because they were thought to be quite scarce. Since then, however, geological studies have shown them to be relatively abundant. The discovery and identification of rare earth elements is complicated by the inherent difficulties in separating them from each other. The rare earth elements comprise the fifteen transition elements of Group IIIB, Period 6, of the periodic table. These elements extend from lanthanum to lutetium and are commonly called the lanthanide series. Samarium and neodymium are the two most common elements used in the commercial manufacture of rare earth permanent magnets. Commercial grade rare earth magnets There are only a few common types of rare earth magnets that are considered in the circuit design for magnetic separators. Early rare earth magnets of commercial significance (introduced in 1970) consisted of the first generation of sintered SmCo5. The energy product of these magnets ranged up to 23 MGOe, which provided the initial impetus to the field of high-energy permanent magnets. Although these magnets did not produce the extremely high magnetic field strengths of current rare earth magnets, they were relatively temperature stable. Containing 66% Co, they are the most expensive of the basic commercial rare earth permanent magnets. Their use is limited today because they are being replaced by second and third generation rare earth permanent magnets.

Jan 1, 1995

By D. W. Park

Longwall mining is popular in underground coal production in the United States due to higher production rates and safety concerns. Because of the extreme complexity, it is necessary to plan an adequate design to achieve a safe and efficient working place. The proper sizes of yield and abutment pillars and panels can be determined by simulation using numerical modeling techniques. By means of three-dimensional modeling, stresses to be imposed on the pillars, panels, gob, and powered supports can be analyzed. In this study, an initial three-dimensional finite element model was developed and then modified into four different models. Using these models, the numerical outputs of distributed stresses on three different sizes of yield pillars, three different sizes of panels, and two different sizes of abutment pillars were compared and analyzed to determine the most adequate pillar and panel sizes. Progressive failure theory based on the Hoek and Brown failure criterion was used to determine redistribution of stresses in the yielded and failed areas in the longwall mine.

Jan 1, 1992

By Kevin Lundberg, Philip Sander, Daniel Weinberger, John Reilly

Since the early days of risk management, developments in technology and guidelines (ITA, ITIG, OGG, UCA) have advanced risk management and probable cost estimating, which are now widely recognized. WSDOT’s CEVP risk-based cost validation process is now established after 20 years. This paper traces these developments, summarizes advanced techniques, and presents examples of US and international projects with results. A particular case of using advanced risk evaluation to allow enhanced-capability TBMs to be considered in a competitive bid process is presented. Further advances, including the use of digital twin risk-based representation of complex projects, are described.

Jun 13, 2023

By J. P. A. Hortley

In conventional electrolytic copper production, looped copper starter sheets, on which the copper is deposited, are supported by hard-drawn copper bars. These bars have cross-sectional areas of between 1 and 1.4 in2. The suspension bars serve two purposes: firstly to support the cathode, which can weigh up to 150 kg, and secondly to introduce the electric current. IYI examined these two requirements in detail to see whether a better design could be achieved. Considering firstly the current carrying requirement, it wee noted that under normal refinery conditions, each cathode carries between 400 and soak. If one applies the generally accepted rule that 1 in of copper can carry 1000A4 a suspension bar need theoretically contain only 1/2 in2 of copper. This contention is supported by the fact that the 500A current passed through the cathode also appears to pass quite satisfactorily through the two support loops, which have a cross-sectional area of approximately 0.35 in 2. Turning now to the strength requirements, the cross-section of hard-drawn copper bar required to support a 150 kg cathode is relatively small, and easily met by the present designs. It is not, however, the static load applied by the 150 kg cathode immersed in the electrolyte which causes the damage to the hard-drawn copper, or even the increased static load of a 100 kg man standing on one foot in the centre of the bar; the damage is actually caused by the dynamic loads applied to the bare when they are dropped, thrown into containers, lowered too rapidly into the cell, or otherwise mistreated. The important requirement is therefore that the bar does not permanently bend. Its proof stress of limit of proportionality, rather than the amount that it deflects under static loading, should be the strength criterion. With the hard-drawn copper normally used for the manufacture of suspension bars, it has been observed that the copper becomes annealed during use, particularly at the end of the bar where the current is introduced. Thus, after a relatively short time, the cathodes are in effect being supported by annealed copper bars.

Jan 1, 1978

By G. M. L. Robinson

Mineral Processing Wastes, as defined by the Environmental Protection Agency (EPA), has determined that most of the mine wastes will be regulated pursuant to subtitle D (Solid Waste Regulations) of the Solid Waste Disposal Act while specific mine waste categories will be regulated within the framework of the Toxic Substance Control Act. Though EPA's determination currently relieves the industry of the regulatory constraints mandated by the Resource Conservation and Recovery Act (Hazardous Waste Regulations) Subtitle C regulatory framework; the industry is not granted immunity from historical or current environmental regulations related to listed or characteristically hazardous or solid wastes. Because of the current regulatory trends and the need to implement cost effective remediation alternatives; advanced currently available on-site remediation technologies are available to minimize, reduce, contain or prevent environmental impacts related to mining and processing activities. In light of industry technical needs, an overview of the research and commercially available remediation technologies will be discussed and a brief discussion of the strengths and weakness of each technology will be presented. Technologies to be discussed includes stabilization, solidification, soil wash, soil flush, thermal distillation, pump and treat, metal extraction, centrifuges, filter presses, bioremediation, and incineration.

Jan 1, 1992

The last twenty years of development in Process Mineralogy are reviewed. Since the milestone review by Henley in 1983, which projected the concept and suggested closer working relations between mineral processing and mineral science, the second generation (1983-2003) has made significant progress. Examples are to be found in improved sampling and high-confidence flotation testing, and in automated quantitative mineral measurement. The recent addition of end-member studies has provided a clearer view of the overall ore mixture milled from its constituent geological components. In all, better predictive abilities have resulted from these improvements to Process Mineralogy. These improvements have led to more significant business impacts in mineral resource characterization, and in optimization of existing concentrator operations.

Jan 1, 2004

By Debra Switzer, Swapnil Urankar, Douglas Watson, Steven Hunter, Chandranth Banerjee, Shashank Pathak

A hydrocyclone is a piece of equipment commonly used as a classifier in mill circuit operations. Traditionally, hydrocyclone performance is characterized by the classification efficiency parameter, such as cut size (d50c), sharpness of separation () and bypass (Rf ). A plethora of endeavors have already been made to develop parametric models to determine hydrocyclone performance that correlate design and process variables. In contrast to those studies, we made an attempt to develop an approach to derive required design parameters purely from hydrodynamic principles that provides a platform to optimize the operation of a hydrocyclone for a given application. In this selection methodology, we calculated the differential pressure at the air core, as well as the tangential velocity at the boundary of the air core from the vortex principle in a confined geometry at different operating regimes. A series of experiments were conducted using Weir’s Cavex® hydrocylone where process variables—such as solids concentration and feed flowrates—were experimentally studied to determine the key classification parameters. For the validation of the current approach we used the same process variables to derive design parameters and compared them with the existing design. The current approach can provide insights towards the selection of design parameters and can be useful for mining industry professionals to optimize different operating parameters of hydrocyclones to achieve the best performance.

Feb 1, 2024