Search Documents

By Leonard Bronitsky

The construction mineral aggregates industry--the largest industry on a tonnage basis--is threatened with large shortages in the near future. Ironically, these common minerals which include sand, gravel, and stone are among the most plentiful in the earth's crust. However, as these minerals are low in value and used in large volumes, they are extremely sensitive to transport cost, e.g., a haul of 20 miles doubled the delivered cost of mineral aggregates. Consequently, these minerals must be located close to points of demand to have economic usefulness. But the development of new deposits is virtually impossible near many urban areas for legal, sociological and economic reasons. The spector of unfinished urban transport systems, curtailed residential construction, and a general deterioration of the physical urban plant, looms as a direct consequent of future mineral aggregate shortages in the U. S. metropolitan areas. The shortages of mineral aggregates in the Greater New York Metropolitan Area (G.N.Y.M.A.) are prototypical of the shortages faced by the U. S. Metropolitan areas. This paper presents an economic analysis of the consequences of not considering the broad aspects of conservation economics as a major component of resource management. The needless annual cost for the G.N.Y.M.A. is shown to be $30 million.

Jan 1, 1974

By Russell J. Sheets

Reactivation of highwall slope failures during adverse weather had intermittently impacted haul road access into a previously mined open pit. These impacts ranged from limited access to full closures; however, the greater impact was to an underground mine that was developed within the open pit. Following several significant precipitation events, a rapid snow melts greatly accelerated movements finally closing the haul road and destabilizing other past failures. In addition to re-designing the overall pit access, the decision was made to relocate the primary portal to a more stable highwall. An accelerated surface geotechnical review was required to advance the portal relocation; however, only existing information from past investigation, existing geology model, visual inspections, and slope monitoring data were available for the assessment - no new investigations or data collection could be completed within the allowable timeframe. The evaluation included a review of the geology, an assessment of the current highwall condition and previously observed performance, and a rockfall analysis to evaluate existing catchment above the proposed new portal location.

Feb 1, 2024

By F. Segobia, M. Portal, F. Ysla, A. Mujica, L. Goicochea

The “Building Our Future” project is a collaborative initiative between the UNC SME Student Chapter and the Water and Earth Museum (MAT) of Asociación Los Andes Cajamarca (ALAC), both corporate entities of Newmont Yanacocha. Its mission is to promote responsible and sustainable mining among new generations while fostering a culture of equality and respect. This comprehensive educational program integrates sustainable development goals and includes workshops led professionals and external experts who share their personal stories to inspire students from rural and urban educational institutions to follow their dreams. Additionally, for this year 2024, the project development and implemented an interactive mobile application that educates users about the use of minerals in everyday life through four levels: Minerals in the Home, Minerals in Medicine, Minerals in Transportation, and Minerals in Agriculture. This multi-faceted approach seeks to raise awareness about the importance of mining in Peru’s economic, environmental, and social development, ultimately fostering a new generation of informed and engaged citizens who understand the vital role of mining in a sustainable future.

Feb 1, 2025

By Lisa A. Banick, Robert A. Rubin

The lawyer's role in underground construction, certainly for the past 20 years, has been principally that of the advocate in disputes resolution. Disputes in underground construction have been steadily increasing, making the lawyer a more prominent participant in the underground construction process. It is widely believed, however, that this is not a salutory state of affairs. It is our thesis that lawyers ought not be eliminated from the process, but rather that their role should be changed. They should function as prophylactics rather than as swords, i.e., they should be used to prevent or reduce disputes rather than, after the fact, to champion their clients' causes. a. Mr. Rubin is a partner in the New York law firm of Postner & Rubin. He has litigated and arbitrated numerous complex construction disputes. He has also participated in efforts to improve contracting practices on committees of ASCE and the National Academy of Engineering. b. Ms. Banick holds a BS in Civil Engineering from the University of Virginia and is a law student at New York Law School. She is a law clerk at Postner & Rubin.

Jan 1, 1983

By James J. Fallon

I'm glad this meeting is being held in New York. First, because the city is close to my home in New Jersey, only 35 minutes from Times Square ..... if I were to come to Times Square between two and three in the morning. Otherwise it takes two hours. But even more important is the fact that all of you good people from around the country and around the world will enjoy the unique experience of that warm friendly atmosphere in the greater metropolitan area, something that you won't see any place else on the face of the earth. Seriously, the greater metropolitan area has been a large part of my industrial, cultural and spiritual experience. There are many aspects of it which I find disagreeable but on net I would rather live in this area, at least for the time being, than any other area of the United States. As a consultant I find contact with financial institutions, corporate headquarters, information sources and a great many production and research facilities a valuable asset to my activity.

Jan 1, 1985

By Y. Tao

The professional status and characteristics of mineral processing were discussed along with the importance of innovative personnel training for mineral processing engineering. Reform ideas and models for the mineral processing engineering education system were suggested to formulate and implement new training program for the mineral processing specialty. It is suggested to strengthen engineering training practices, cultivate the culture of innovation, improve innovative education system and insisting on the combination of teaching with production and scientific research as the important means of training innovative talents for mineral processing engineering.

Jan 1, 2010

The most important event affecting the United States coal industry in 1993 was the strike by the United Mine Workers of America (UMWA). This was a series of selective strikes, beginning with a strike against four Peabody Holding affiliates on Feb. 2, following unsuccessful contract negotiations between the UMWA and the Bituminous Coal Operators' Association (BCOA). Although that strike ended on March 3, the failure to reach a new contract agreement led to walkouts at several Midwestern mines on May 10. During the summer, the strike expanded to include mines of 13 companies in seven states including Ohio, Pennsylvania, Illinois, Indiana, Kentucky, Virginia and West Virginia. About 17,000 miners were idled during the strike. As the prospects for a settlement diminished, the Secretary of Labor appointed a federal mediator. The mediation resulted in a five-year contract. In addition to increases in wages and pensions, it was agreed that 60% of new job openings would be filled by laid off and active UMWA miners. In return, companies won the right to establish more flexible work rules and scheduling of miners. While some health care benefits were expanded, the agreement established a new health care system that was designed to reduce costs. Preliminary Energy Information Administration (EIA) data indicate that US coal production fell by 5% in 1993, to 859 Mt (947 million st) (Table 1). The strike was one of the primary causes of the decline in production. Another significant cause was a 27% decline in coal exports. Also, a very small displacement of domestic coal production resulted from a rise in coal imports.

Jan 1, 1994

By Michael Gay, W. H. Hansmire, G. Rippentrop, V. S. Romero

The new Tren Urbano heavy rail transit project in San Juan, Puerto Rico has one very significant part, the Río Piedras Contract, being constructed underground. This paper will give an overview of the tunneling work that started construction in1997. Design-Build procurement for tunneling is addressed. The new and modern transit system in San Juan will be 17.2 km (10.7 mi)long and have 16 stations in its first segment of construction, which is due to open in 2001. The line connects the city center district of Santurce to the outlying suburban municipality of Bayamón. All construction is being done under design-build contracts as a demonstration project funded by the Commonwealth of Puerto Rico and the Federal Transit Administration (FTA). The Río Piedras Contract is completely underground and involves practically all types of construction in soft ground. One station is built as cut-and-cover at the University of Puerto Rico. One portion has twin tunnels to be driven with an Earth Pressure Balance Machine (EPBM) and lined with one-pass precast concrete segments. Another has four short tunnel drives at a turnout that will be constructed with an initial support of shotcrete and lattice girders (i.e., the New Austrian Tunneling Method of construction). The most complex construction is the Río Piedras Station, which is being built as a stacked drift with a total of 15 individual tunnel drifts. After being sequentially excavated and concreted, they will form the arch of the 19 m (62 ft.) wide by 16 m (53 ft.) high cavern station. This structure is excavated in soil with less than 5 m (16 ft.) of cover to overlying historic buildings.

Jan 1, 1999

By Elmer R. Drevdahl

During the last few years there has been a rapid increase in the development of the community or junior college throughout the United States, Some factors behind this development include the need for more college facilities to service the growing number of high school graduates, the desire of the public to provide some post high school education at reasonable costs, and the need to provide post high school educational opportunities not now provided by most of the universities and colleges. Many of the new community colleges provide at least three educational services including local opportunity to provide the first two years of a four year college program, two year technical-vocational programs of a terminal nature, and adult educational opportunities. The community college has the advantage of not being saddled with years of academic tradition which prevent it from changing to suit the educational needs of the community It serves. The flexibility of the community college in developing new programs, particularly in the technical areas, is going to provide industry with many of the badly needed technicians it is now unable to secure.

Jan 1, 1965

By James F. Holzbach

Although Disputes Review Boards have been used for some time, they had not received wide publicity at the time Monroe County first used one. Public owners frequently resist adopting new contracting practices. This paper discusses an owner's experience with Dispute Review Boards, from learning about them to their use on two (2) projects. The experiences of potential and actual contractor claims are compared to a claim on an earlier contract and the ensuing litigation. Suggestions for possible use for Owner-Engineer disputes and recommendations for use are provided.

Jan 1, 1995

By Douglas H. Bolton

In recent years, equipment manufacturers have been busy developing remote control systems to catch up with the sophistication and efficiency of continuous miners. Now the tables are turned, and manufacturers are undertaking the new challenge of upgrading, refining and equipping continuous miners to take full advantage of the capabilities made possible by modern, successful remote control systems. Because the operator can safely advance the miner farther without pulling out for roof bolting, continuous miners now need to be equipped with means of complying with correct face ventilation, dust suppression, methane detection, diffusion and improved lighting. Some of the exciting possibilities being developed to catch up with remote control include feedback controls using laser beams as datum points, coal sensing devices with feedback signals to show the operator what the machine is doing, show where it is relative to the coal seam, how hard it is working, and more sophisticated use of cyclic control. Mining machinery manufacturers have accepted the new challenges, and faster, safer mining procedures are already in sight.

Jan 1, 1975

By H. V. S. Tingley, D. Helfant Ghose

"Ten years ago," said a mining industry personnel manager, "we used to wine and dine new mining engineering graduates. Now I can pick and choose among men with 10 years of experience." Comments like that are common throughout the industry today. During the 1970s, the US and Canada did indeed suffer from a severe shortage of mining engineers, especially experienced ones. Moreover, it seemed likely this North American shortage would worsen. Increased production of minerals and coal was pushing demand for mining engineers upwards, and there appeared to be substantial new employment prospects for them in the nascent synfuels industry. The oil majors entering the mining industry were pushing for an increased professionalization of mining management, heralding a trend towards higher intensity in the use of mining engineers. In response to the shortage, mining schools expanded their programs dramatically. By 1982, American schools were churning out more than 600 new mining engineers per year, compared to barely 200 in 1970 (Table 1). The timing of the explosion in the number of mining engineers could not have been worse. The downturn in the economy and the resulting slump in the mining industry coincided almost exactly with peak output of mining engineers. The market for mining engineers shifted from shortage to surplus with startling rapidity. The new crop of engineers, no longer courted by the mining companies, struggled to find any mining jobs. At the same time, experienced mining engineers found themselves thrown into the job market, some for the first time in decades. The current oversupply of mining engineers is assumed to be a temporary phenomenon. As the economy recovers, the demand for mining engineers is expected to pick up at least enough to absorb today's surplus. Not so, according to a recent study by Fenvessy and Schwab, a general management consulting and executive recruiting firm. In 1979, Fenvessy and Schwab was commissioned by a group of major mining companies to conduct a worldwide study of supply and demand for mining engineers to the year 2000*. The study began at the height of the North American shortage. One major objective of the study was "to identify means by which business and educational institutions may cope with and alleviate a future shortage of mining engineering talent." The findings, however, ran directly counter to expectations. The current oversupply will not disappear with economic recovery, the study concluded. In fact, the US and Canada are facing a massive oversupply that will probably last until the end of the century, unless enrollments in schools are reduced. Study Method Fenvessy and Schwab's conclusions are based on supply and demand models for mining engineers that it developed in the course of the study. Specifically, predictions for the supply of mining engineers are based on a survey of the 54 mining schools that account for about 90% of the world's annual output of mining engineering graduates. This survey asked for data on historical and projected number of graduates, obstacles to further expansion, changing trends in the use of mining engineers, and graduate career patterns. Fenvessy and Schwab developed three mining engineering supply scenarios from the survey data. The high case, considered unlikely for most of the industrialized world, is based on a continuation of the 1970's soaring growth rates. The middle case was established from the mining schools' own estimates of future growth in the number of graduating mining engineers. Finally, a "low growth" case for the US and Canada assumed that the number of graduating engineers will remain at current levels. Mining engineering demand was forecast using a complex model based on the demand for 50 major minerals. Formulas were

Jan 9, 1983

By Robert A. Metz

During the past decade we have witnessed spectacular improvements in productivity of open pit mining equipment. Thousand-horsepower engines, 200-ton trucks and 15-yard electric shovels, which such a short time ago were just dreams on a drawing board, are now realities. More productive equipment and metal shortages have encouraged increased production at existing mines and the development of new larger tonnage operations. Operators and engineers have been able to employ computers and various other types of automation to "stay on top of things". The mine geologist, however, is merely faced with a bigger and more rapidly changing pit to pick in. Keeping geologic information current in these mines presents entirely new problems to mine geological staffs. To obtain adequate geologic information on the developing orebody requires enlargement of the staff to share the work load or revision of methods in keeping with the times. The former has the disadvantage of loss of the comprehensive knowledge of the pit that a chief geologist likes to have, not to mention management's usual lack of enthusiasm for force increases.

Jan 1, 1970

By Stephen R. Brown

Current conditions in the gold market demand that mine and plant operators make budgeted production targets at the lowest possible unit costs. For those companies bringing new gold pro­duction capacity on-line, achieving budgeted production levels as quickly as possible after start-up is vitally important to mini­mize unit costs and to begin a positive cash flow. Whether the objective is to simply improve unit costs or successfully start-up a new, complex plant, success will be strongly influenced by the skill levels of the operators and supervisors. The only way to assure return on plant investment, and to survive during depressed metal prices, is to ensure that plant operators have the knowledge to effectively run the plant. Technology available in computer-based, multimedia training systems, including: inter­active animation, videos, voice-overs, schematics, and text can now be used to train operators at their own pace using plant-spe­cific information. Additionally, it has been shown that learning through multimedia provides a higher degree of long term reten­tion than more traditional learning methods.

Jan 1, 1998

By Frederik P. Agterberg

Mineral exploration consists of the acquisition of data and their interpretation to ascertain the presence or absence of uncertain events. In general, the amount of uncertainty decreases during exploration when targets become increasingly well defined. Decisions on further exploration and whether or not mining should be commenced are based on new information using both objective facts and subjective reasoning. Computers play an important role during all stages of exploration. Three recent books (References 1-3) on decision-making in exploration and mineral-resources evaluation provide additional background supplementing the papers in this volume and articles in scientific journals or other conference proceedings (e.g., References 4 and 5) dealing with the subject. Other new developments to be considered are that microcomputers are becoming increasingly important in the earth sciences (Reference 6), and so are applications of artificial intelligence (Reference 7). Microcomputer- based technology allows rapid communication between field parties and main office. Expert systems are becoming increasingly sophisticated aids for mineral exploration an can now contain objective rules based on statistical theory (Reference 8).

Jan 1, 1989

By Thomas P. Meloy

A brittle solid broken by crushing or impact, results in a mass size distribution curve having a straight line segment when plotted on log-log paper. Depending on the mineral, the slope of this straight line segment ranges from a maximum of one for materials like glass and quartz to values of one half or less. Theoretical derivations of the size distribution, such as the Gaudin-Meloy model, yield a slope of one and only one. When the Gaudin-Meloy model is modified to assume that not all cracks terminate on a preexisting surface, the new model predicts that size distribution slopes, depending on the type of brittle solid, will be less than one. There is a measurable physical parameter that will predict the slope. In addition the model predicts that particles from such a size distributions will have negative corners and peaks - indentations. Moreover the model predicts that particle shape will systematically change with decreasing particle size. Finally, this new physical model of comminution may be experimentally tested.

Jan 1, 1995

By Terence G. McCusker, Bruno Dietl

The only previous attempt to use a tunnel boring machine in the rock formations encountered in New York City was unsuccessful. However, technology has been developed since then which made a new attempt a practical proposition. Nine thousand feet each of 8'6" and 11'0" diameter tunnels were driven in Manhattan schist using Jarva TBM's together with 1100 ft. of the smaller diameter driven conventionally in Inwood marble and earth. (1) The selection of tunneling method was largely based on the need to avoid community reaction and hazardous tunneling conditions where the larger diameter tunnel passed beneath residential structures in poor condition in seamy and blocky rock. Experimentation with cutters and cutter mountings indicate that good cutter life and ease of change are available. It was found practical to use unusually large muck cars for an efficient muck disposal system. Conventional tunneling was successfully executed beneath a subway station whose invert was less than seven feet above the crown of the tunnel. Attempts at chemical consolidation and dewatering were unsuccessful in the earth section which was completed under compressed air.

Jan 1, 1974

By G. T. Adel

Hindered-bed separators are often used in the minerals processing industry to classify particles according to size and density. A new technology, known as the Eriez CrossFlow, was recently developed to overcome some of the limitations associated with hydraulic separators. The innovative feature of this unit is a novel feed presentation system that improves separation efficiency and capacity. In the present work, a detailed process engineering evaluation was conducted to determine the basis for the improved performance of this unit. The evaluation included controlled separation tests using well-characterized feeds, particle and liquid tracer experiments and mathematical modeling studies. Data obtained from this work show that the new separator is capable of maintaining good separation efficiencies at higher solid feed rates than traditional designs due to improved hydrodynamics in the separation zone. This paper reviews the operating principle of the Eriez CrossFlow separator, discusses the results of the tracer experiments and modeling studies and presents test data obtained from recent laboratory and plant trials. Key words: Size classification, CrossFlow separator, Hindered-bed separator, Hydraulic separator

Jan 1, 2003

A new separator, known as the HydroFloat cell, was developed to overcome the limitations of traditional flotation cells in recovering coarse particles. The HydroFloat cell separates particles based on differences in mass after the selective attachment of air bubbles to the hydrophobic component of the feed stream. Proof-of-concept testing, utilizing phosphate matrix, heavy mineral sands and anthracite slag, indicated that significant improvements in separation efficiency can be achieved using this air-assisted teeter-bed system. Based on the encouraging laboratory results, a pilot-scale HydroFloat cell was fabricated and installed at a central Florida phosphate plant. Test data collected using the pilot-scale unit suggest that the BPL recovery of the +35-mesh plant feed can be increased by snore than 40% through the application of this new technology. This improvement is particularly beneficial due to the very high grade (-73% BPL) of the +16-mesh particles in the HydroFloat concentrate. This article describes the theoretical basis for the development of the HydroFloat cell and provides an overview of recent laboratory and pilot-scale test results.

Jan 1, 2002

By Benjamin K. Pocock

When considering alternative equipment choices in mill or process flowsheets, it is important to determine both capital and operating costs of such equipment as well as other possible savings related to downstream operations. This paper presents a few case studies and shows cursory guidelines for the selection of equipment for new installations or in the retrofitting of existing plants. Based upon recent plant experience, suggestions are given to improve the operation of clarifiers, thickeners and vacuum filters.

Jan 1, 1986