Search Documents

By Timothy G. Shuttleworth

In the late1970s, mineral processing plants producing copper sulfide concentrates and oxide leaching feedstocks went online with operating tonnages that exceeded traditional installations. This created a need for larger capacity belt conveyors and apron feeders. Apron feeders are slow moving, heavily loaded conveyors that feed a deep bed of ore from a bulk holding location (a bunker) as a controlled stream, often into a large capacity crusher. Apron feeders use sprockets and caterpillars, while belt feeders use rubber belts with motorized head pulleys to convey the material. The damaging of belts and clogging of transfer points from tramp iron required larger magnetic separators and the removal of tramp metal cannot prevent these serious problems. Corrective action at this location is important for two reasons: Removing tramp iron early in the ore stream protects downstream equipment from potential costly damage. Installing apron feeder magnets before the primary large capacity crusher means that secondary and tertiary crushing steps (made up of multiple parallel units) operate more efficiently, since tramp metal is removed at the onset.

Jan 1, 2011

By Fathi Habashi

OXIDE ORES can be divided into two groups: 1) Simple oxides (Table 3.1). 2) Complex oxides. Those ores containing minerals composed of two oxides; an acid oxide (Cr2O3, Nb2O5, etc.), and a basic oxide (CaO, FeO, MnO), as shown in Table 3.2.

Jan 1, 1970

By L. F. Barrett, D. E. Cameron, J. C. Wilson

Exploration by Anaconda Minerals Co. in the Rico area from 1978 through 1983 resulted in dis¬covery of the Silver Creek molybdenum deposit. The drill-indicated resource is 40 Mt (44 million st) of 0.31% Mo, and projections suggest that the deposit may exceed 182 Mt (200 million st). No source intrusion has been intersected by drilling, but its presence is sugested by intramineral silicic alkali-alaskite porphyry dikes observed at the surface and in drill holes. Age dates and fluid inclusion studies indicate that the deposit was formed 5.2 ± 0.2 m.y. ago and that more than 1200 (3937 ft) of cover has since been removed by erosion. The deposit is hosted by Precambrian quartzite and greenstone, and Paleozoic sediments. Three prominent faults intersect in the vicinity of the molybdenum deposit, and one of these, the Last Chance fault, strongly influenced the shape and location of the deposit. The juxtaposition of host rocks across the Last Chance fault reflects significant offset spanning at least three different periods. Wallrock alteration associated with the deposit includes potassic, phyllic, and propylitic zones in noncalcareous rocks and garnet and anhydrite-diopside zones in the carbonates. All +0.2% Mo mineralization is within the potassic and garnet zones. Premineral faults that intersect the deposit contain the only surface molybdenum, tungsten, and fluorine anomalies. Dispersion halos of the indicator elements were defined by drilling in the discovery phase of exploration, and are particularly well-developed in the hanging wall of the Last Chance fault.

Jan 1, 1987

By Mortimer J. Richardson

In the context of this session on "Practical Placer Mining," a projection of the present into the future first assumes that there is a future for Placers. The second assumption is that there is the combination of adequate reserves and a willing, mining investment source to finance placers. This paper will point out the opportunities on both assumptions, illustrating my positive position on the future of gold placers. In order to focus this paper more effectively, I have chosen GOLD as the subject mineral. However, it is recognized that much of the technology for exploring and mining gold placers has been applied to other alluvial deposits; including platinum, diamond, tin, and various industrial minerals (which are often referred to as "placers" though this contradicts historical definitions). Over the past 10 years I have presented several papers on the general subject of placers, most of which are listed under References. These have included topics such as exploration, evaluation, small-scale gold placer mining and decision-making, mining and processing equipment designs, and dredge-mining operations. In an attempt to identify the more promising, undeveloped placer potentials in the world I have usually mentioned the USSR and China but qualified them as being either inaccessible, or, politically difficult to obtain. However, with recent developments in the USSR, the obstacles appear to be somewhat diminished.

Jan 1, 1992

By Bernd Hagenah, Petr Pospisil, Colin Santangelo

This paper explores the profound implications of high-speed train operation on tunnel planning, specifically investigating ongoing high-speed rail projects in California and Texas. The paper delves into the crucial considerations for designing high-speed rail tunnels, including selecting tunnel sections based on aerodynamic factors, which impacttraction power requirements and pressure comfort. The paper also examines the need for emergency stations, maintenance access, and comprehensive safety and rescue concepts to address train incidents. Drawing from international high-speed rail projects, it shares valuable experiences and lessons learned to promote efficient and secure tunnel designs for high-speed train operations.

Jun 23, 2024

By Joseph A. Dos Santos

The Expanded Conveyor Technology, a rationalization of the conventional conveyor technology, allows us to apply the theory and principles beyond the current (perceived) limits. This was first prompted by the writer's advancements in Sandwich Belt High Angle Conveyors. The introduction defines the Expanded Conveyor Technology and outlines the range of applicability for the wide variations in conventional and non-conventional conveyors. The writing deals with the theory and design of sandwich-belt, high-angle conveyors in the context of the Expanded Conveyor Technology, including the equations of friction, hugging pressure and the continuity of hugging principle; curvature constraints and criteria for tension, curvature, trough, and belt construction; and drive and tension analysis, load sharing and traction, including "derived load equivalents."

Jan 1, 2000

By E. Peuraniemi, S. Strömberg, S. Jyrkönen, A. Jokilaakso

Several sulfidic raw materials have been flash oxidized in a laboratory furnace in oxidizing atmospheres at temperatures of 500-1100°C. Chemical analysis was used to determine the oxidation degree, and optical and scanning electron microscopy combined with energy dispersive analysis were used for characterization of the reacted particles. The studied materials included both Cu and Ni concentrates and mattes. In fixed conditions, the temperature dependence of sulphur removal rate was found to be equal for all the copper concentrates studied. Nickel concentrates and Cu- and Ni-mattes were, however, found to be less reactive. Most of the particles were found to spheroidize and to fragment to small droplets under intensively oxidizing conditions. The product particles were frequently found to be iron oxide cenospheres or dense spheres with a composition of mixed Cu-(Ni-)Fe oxides.

Jan 1, 1998

By B. Tönjes

In the course of the last decade, the concept of sustainability has turned from a catchword into a vision - a vision to which politics and industry feel increasingly committed. In terms of the energy industry, the key criteria for sustainable development are supply security, economic efficiency and social responsibility. Coal is able to meet all these criteria if it is produced in conformity with high safety standards through the use of modern mining technology and converted into electricity with the aid of environmentally friendly methods. Among the fossil energy resources, coal will, according to the vast majority of global energy scenarios, continue to be the most important input energy in power generation for the foreseeable future. Coal is therefore today, and will in future continue to be, an important element in ensuring sustainable energy and raw material supply, worldwide, in Europe and also in Germany.

Jan 1, 2005

Part two of this three part series looks at explosives use in open-pit and underground mining operations. Part three, next month, will discuss the transportation, storage, handling, and destruction of explosives. Larger ore bodies, lower grade deposits, and more difficult geologic conditions have led to changes in blasting products, techniques, and field practices in both open-pit and underground metal mines. Pit blasting operations must consider the material's geology, needed fragmentation for the material, and hole diameter and depth-as well as the traditional consideration of the type of explosive used. With underground mines, various blasting aspects of burn, angle, and machine cuts must be considered for an efficient and safe operation. Of the factors related to open-pit blasting, geology of the material is most important. Many theories relating to sonic velocity and rock hardness are used to determine needed explosives ratios. Extensive field tests are necessary to determine these factors. In most cases, results assume that the material to be broken is homogenous. The drilling penetration rate is sometimes used as a guide to determine rock hardness; however, this is not necessarily a good idea. In many cases, a very hard, brittle rock will blast with less difficulty than a soft, spongy rock. The formation's stratification is also important. In thinly laminated horizontal seams, rock will usually break and adequately fragment with relatively large burdens and spacings using a low explosives ratio. Massive formations with few laminations require close burdens and spacings and a high explosives ratio. When the stratification is pitched on a severe angle, it is usually preferable to develop the pit face 90°-but no less than 45°-to the stratification. If the face must be developed parallel to the stratification, burdens and spacings must be reduced and the angle drilling that will conform to the angle of the lamination should be given serious consideration.

Jan 8, 1981

By Jae-Chun Lee, Kang-In Rhee, D. B. Dreisinger, Hyo-Shin Yu, G. A. Kordosky

The development of a process for direct synthesis of very pure ZnO powders from zinc-bearing waste was investigated. The zinc waste which contains 55% zinc was leached with sulfuric acid. After iron removal by hydrolysis from this zinc solution, purification through solvent extraction by the use of D2EHPA as an extractant was carried out. Then, loaded zinc in the organic solution was stripped and precipitated simultaneously using oxalic acid as a precipitant. Synthesized ZnC2O4 precursors by precipitation stripping were calcined to obtain ZnO powders exceeding 99.9% purity. The effects of sulfuric acid concentration, leaching time, and pulp density on the extraction of zinc were studied and optimum conditions for the solvent extraction were obtained through purification of the zinc solution. The size, morphology, and size distribution of synthesized ZnC204 powders were studied in terms of oxalic acid concentration, temperature, surfactant added, precipitation time, etc.

Jan 1, 1993

By C. Tsamantaki

Water-bentonite suspensions exhibit a yield stress which is defined as the minimum applied stress for flow. Considerable debate exists about the yield stress being a material property, hence different measuring methods should give similar answers, but several investigators have demonstrated that it is an engineering reality. Yield stress is normally estimated indirectly from the rheogram obtained with a viscometer following an extrapolation to zero shear rate (the dynamic yield stress), but the technique may be prone to errors because of slip flow. Direct measurements, not prone to such errors, rely on an independent assessment of the yield stress, normally carried out with the vane method (the static yield stress). In this paper results are presented and compared regarding the yield stress of 14 different water-bentonite suspensions measured using both the direct and the indirect methods. In order to obtain a wide range of yield stress values, two different types and two concentrations of bentonite at various pH were tested. Rheological data were obtained using a rotational speed viscometer and a yield stress vane measuring device. Measured vane yield stress values ranged from 5 Pa to 83 Pa. Rheological data collected with the rotating viscometer were fitted using various conventional techniques (interpolation, linear and non-linear regression analysis) as well as using a golden section yield stress search methodology based on Herschel-Bulkley model, developed in house. The vane instrument measures directly the yield stress of the suspensions and requires no further data handling. A comparison of the measured values of the yield stress with the direct and the indirect method is then made for the water-bentonite samples. Not very large differences are observed among different techniques and the variations are discussed. Similar data from literature are also analyzed and the comparison shows that differences on the various estimation methods are much larger than the differences observed in this study.

Jan 1, 2006

By N. B. Prenn

Case Studies in Open Pit Design Using Whittle 4D will be discussing the following four examples: 1) Optimization of process plant design using Whittle 4D as a sizing tool. In this case, the home office and project team had different views of the size of the final project. The home office wanted to reduce the size of the project to reduce capital expenditure, while the project team suggested a larger project. Whittle 4D was used to determine Net Present Value and Internal Rate of Return using the Whittle scheduler (FDAN) to schedule many alternatives, and calculate the NPV and return for each alternative. 2) Comparison of pit optimization methods: Lerchs-Grossman vs floating cone. Many pits are developed based on floating cone economics. A comparison of methods in one large gold mine resulted in the stripping ratio of the pit being reduced by 10% in the Whittle 4D optimization as compared to the floating cone optimization. 3) Pit optimization to determine if a new mill is justified. A large heap leach gold and silver mine needed to determine if a new mill was justified. The planning and scheduling would take several man months if completed without pit optimization and scheduling software. Whittle 4D software proved to be very effective in providing optimized pits and a mine schedule in a short time frame. 4) Pit optimization to determine how to mine and size. Open pit optimization determined where the underground operation should start, and whether the material should be processed by milling or heap leaching. One of our clients asked for help in determining where the pit should end and a new underground operation start. We used Whittle 4D to help determine where the pit should end and where to go underground. In addition the operation needed to determine how to process the material.

Jan 1, 1996

By Ricardo D. Presnell, Erich U. Petersen, William J. Tafuri, Donald M. Hausen, Russell C. Babcock, William L. Gunter, Thomas R. Gibson, Douglas N. Halbe, Jay W. Hammitt

The Barneys Canyon orebody is a sediment-hosted disseminated gold deposit located 8 km (5 miles) north of the Bingham Canyon porphyry copper mine. Mineable oxide reserves are 8.6 million tonnes (9.5 million short tons) grading 1.64 g/tonne (0.048 oz/ton) gold. Host lithologies are carbonates and siliciclastics of the Park City and Kirkman-Diamond Creek Formations of Lower Permian age. Gold distributions are controlled by favorable stratigraphic units and associated alteration, and structures. Dominant alteration is decalcification and bleaching of carbonates, and argillization and bleaching of sandstones. Gold to silver ratios are greater than 1:1. Anomalous trace metals include arsenic, antimony, mercury and thallium. The Melco deposit lies 2.4 km (1.5 miles) southwest of the Barneys Canyon deposit. It is spatially associated with a steeply northwest-dipping siliciclastic breccia in the Kirkman-Diamond Creek Formation at the contact with underlying orthoquartzites of the Freeman Peak Formation. Both gold-bearing oxidized and sulfide lithologies are present, often in sharp contact. Mineable oxide reserves are 2.8 million tonnes (3.1 million short tons) grading 2.40 g/tonne (0.07 oz/ton) gold. Anomolous trace metals include arsenic, antimony, mercury and thallium, which are generally present in concentrations greater than those at Barneys Canyon, particularly in sulfide-bearing material. A spatial, temporal and genetic relationship is proposed between the Melco deposit and late-stage gold mineralization at Bingham Canyon, although both the Melco and Barneys Canyon deposits have many similarities to Carlin-type gold deposits.

Jan 1, 1990

By Mark A. Anderson

INTRODUCTION The accomplishment of a well engineered design, and the realization of efficient plant operation cannot be achieved without weaving a web of safety consciousness from the beginning of the project. When the plant becomes operational, and throughout its life, responsibility safety will rest with the client or operator. Recognition of this understanding does not reduce the importance of the engineering and construction contractor's role, but merely puts the responsibility where it belongs. A project which has had little or no operator input during the early stages of design is almost certain to have serious work place safety, health, and environmental problems in spite of the fact that all MSHA and OSHA design requirements were met and the engineering was performed using accepted practices. DEFINITIONS The author has a personal preference in safety definitions that begins and ends with simplicity. If the safety criteria, program, and rules are confusing or complex, the results will soon become obvious. Confusing and complex are the key elements in the avoidance of responsibility and if punitive is added to the list, a brew exists which breeds accidents, illness, and poor performance. A safely designed and operated plant is one that a worker can journey to each day; leaving that person and his or her family with the above average expectation that the person will return healthy, emotionally intact, and hopefully a little wealthier. If the objective or results of a planned or existing safety program don't fit the definition. then the reader is probably contemplating a very sophisticated

Jan 1, 1986

By Valerio Violo, Antonio Raschillà, Livia Cicinelli

"The Cityringen project foresees the construction of a new circular metro line in and around the city center of Copenhagen. Both drives, the north and the south one, required the TBMs to be equipped in order to cope with contaminated water table and soil. The north drive mined in water contaminated with chlorinated compounds, including chloroform and vinyl chloride, while the south TBMs excavated in a highly benzene contaminated area, becoming the first TBMs to complete such a challenge. Despite the pollution and the stricter operative procedures, the production has been extremely successful with record up to 520 m in one month and 32 m in one day. 1 INTRODUCTION The Cityringen is an extension of the existing metro line. The 15 km long twin tunnels will form a new circular line with 21 new stations (17 + 4 crossovers). When finished it will interchange with the existing metro, rail and bus infrastructure at key locations around town, taking 90% of Copenhagen citizen at less the 600m from a metro station (Figure 1). The Contract has been awarded in April 2011 to the Copenhagen Metro Team (CMT), a joint venture between the Italian companies Salini Impregilo, Tecnimont and Seli SpA. Tunnels are being excavated with 4 Seli-Kawasaki EPB TBMs, two of which manufactured in Denmark by Seli Tunneling Denmark ApS, which is also operating them. At the moment this article is written 50% of the tunnels have been completed and over 40% handed over for the electromechanical works. Seli Tunnelling Denmark is a Danish company constituted in 2012 as a subsidiary of Seli SpA for this project and subsequently acquired by the Salini Impregilo Group in 2015."

Jan 1, 2016

By Allan M. Johnson

Since 1974 researchers at Michigan Technological University have been studying mine subsidence in the Iron River District of Northern Michigan. The district, which was active from 1881-1978, has had numerous cases of subsidence. Much of the subsidence resulted from rock mass failure but some appeared to have developed primarily in the thick glacial overburden which is a typical feature of this area. This latter observation led to the recognition that some of the surface subsidence was due to piping; i .e., loss of overburden material to the mine voids by groundwater flow (Johnson and Frantti, 1978). The Sherwood Mine was the last mine to operate in the district. With its closedown scheduled for late summer of 1978, a unique opportunity to monitor the mine as it flooded was presented. It was reasoned that with the cessation of pumping, groundwater would rise in the overburden and the mine would flood. The physical characteristics of the mine were favorable for piping to occur as the mine flooded. With the permission of Inland Steel Mining Company and the support of the U. S. Bureau of Mines, a project to monitor the Sherwood Mine for piping subsidence began in June of 1978. This paper present aspects of this study pertinent to the piping-induced subsidence events which occurred at the Sherwood Mine in 1980 and 1981, including acoustic emission monitoring of the subsidence activity, hydrologic monitoring of the groundwater regime and the flooding mine, laboratory modeling of the piping mechanism, and analytic procedures which are under development.

Jan 1, 1982

By V. F. Hollister

Epithermal gold deposits occur in and near the marginal fault that circumscribes the Goldfield, Nevada, Tertiary caldera. The gold occurs disseminated in alunite, pyrite, and kaolin- bearing silicified zones that are controlled by the circular faults. Other Tertiary calderas (i.e., Summitville and Red Mountain No. 3) have epithermal disseminated gold deposits located in and near their marginal circular faults in settings that resemble the Goldfield example. These additional caldera- controlled epithermal gold deposits are also characterized by alunite, pyrite, and kaolin-bearing silicified rock that act as hosts for the gold disseminations. The Goldfield District is therefore an exploration model for those seeking disseminated epithermal gold deposits in a caldera setting.

Jan 1, 1986

By Scott G. Britton

Many times during the construction of a project, whether large or small, the engineer will become involved with management of the work and workforce. In some cases, mine management will turn over the direction and responsibility of doing the work to the engineer. Because of this, it is important to know some of the basic principles of human resource applications- among other management concerns. This chapter, therefore, looks at the fundamental principles of human resource management. Three broad discussions are presented to the reader. These are: (1) organization, communications, and responsibilities of management; (2) analysis of worker motivation; and (3) supervisory leadership. Each topic encompasses the current thinking for coal mining and mining management. Much of the information in this chapter comes from Practical Coal Mine Management, by this author and published by John Wiley & Sons, Inc., which discusses in depth many of the ideas presented here. Interested persons are directed to this text for more information on management skills.

Jan 1, 1983

By P. Massacci, F. La Marca, G. Bonifazi

Some deposits of inhomogeneous materials, which occur near the surface and are exploitable by open-pit mining, may he characterized in real time prior to mining through groundsurface imagery. If the slice to be stripped is not overly thick, surface texture and color properties may be extrapolated to its entire thickness. Image-analysis techniques for processing ground-surface images acquired in situ or in the laboratory shortly after their acquisition have been developed. These images yield pattern vectors representative of red, green and blue (RGB) color component distributions and hue, saturation and brightness (HSB) texture parameters. The techniques were applied to a sandy ore deposit containing three lithotypes. Geostatistical analysis indicated that the data used to characterize the lithotypes were reliable. The correct recognition of the lithotypes was carried out using a multibarycenter classification algorithm. Such in situ image-analysis procedures provide a means for selecting the ore to be mined, selecting the proper ore-processing method and determining the appropriate blend to he processed. This can be done either before or during mining.

Jan 1, 2000

By Wayne W. Murdy

Since 1993, Newmont Mining has been growing through the development 'q of three major foreign mining operations with a fourth under construction. The first project, Yanacocha in Peru, began operating in October 1993. This occurred at a time when political and business risk in that country was considered high. In 1995, Newmont began operating the Muruntau joint venture in Uzbekistan. It is the first mining project of its kind in the Confederation of Independent States (CIS). In early 1996, Newmont started operating the Minahasa Mine in Indonesia. In early 1997, Newmont began construction of a $1.9-billion project in Indonesia. The company is also completing a feasibility study with its partner for the development of a gold operation in Mexico. All of these projects have been considered "risky" by most standards. Newmont has been successful in all of them through risk mitigation programs. These programs include using strong and successful in-country partners, concentrating on developing a strong national workforce with minimal expatriate employees, using World Bank, European Bank for Reconstruction and Development (EBRD) and International Finance Corp. (IFC) financing and building and maintaining strong ties with host governments.

Jan 1, 1997