Search Documents

By Z. M. Zavodni, M. K. McCarter

This paper identifies physical conditions responsible for past instability of the Main Hill area in Kennecott Copper Corporation's Bingham Canyon Mine, Bingham Canyon, Utah, and describes successful stabilization techniques employed in this slide zone. Geotechnical highlights of recent slides are presented, including monitoring, geological engineering data collection, hydrology, physical rock properties, and stability analyses. Local conditions responsible for slope movement in the Main Hill zone are: (1) high pore water pressure that causes a substantial decrease in real and effective material strengths; (2) continuous structural systems that allow sliding in the more competent rock zones; and (3) broad areas containing fractured, altered , and incompetent rock and soil- like materials. The failure mode is structurally controlled and involves a circular-type soil failure in the toe region initiated by excessive pore water pressure. A surface mapping method is presented which assigns rock mass quality on the basis of block size and rock substance strength. This site characterization technique has successfully predicted slide boundaries and failure modes; used in conjunction with laboratory determined shear strengths, it has provided basic input for calculating slope safety factors in the Main Hill slide zone.

Jan 1, 1977

By R. D. Lama

Coal mining is one of the major sources of methane release to the atmosphere by human industrial activities and is believed to contribute to -30% of the total methane emissions from industrial activities. In 1993, world saleable black coal production, attained almost 3.5 billion tonnes from which around 65% was produced underground. Coal in underground mines can contain high quantities of methane and some deep coal seams have methane content as high as 50 cubic meters per tonne of coal. Gas is re- leased during coal mining from the mined seam and in a higher degree from the neighboring unmined seams and gas bearing strata which are fractured as mining advances. This paper de- scribes a study which was undertaken to estimate the extent of methane emissions from coal mining in the world. Measured emission related data were collected from most underground coal producing countries in the world. The data included methane flows in the ventilation system, methane flows in gas drainage system, in-situ gas content, methane utilization and coal production. More comprehensive data were collected from a range of gassy and non-gassy Australian mines. Residual gas content of samples from run of mine were also measured. Using the Australian data, mathematical expressions were established to evaluate methane emissions as a function of coal production and in-situ gas content for other mines. These emission models were then used to evaluate the emissions for the countries or coal basins without measured emission data. Trends in methane emissions from underground mining for the year 2000 and beyond were also estimated.

Jan 1, 1997

By Peter J. Tarkoy, Terence G. McCusker

INTRODUCTION The discovery of oil and gas reserves in the North American Arctic has led to substantial thought being given to their development. Systems adequate for exploration are not always, or even often, suitable for permanent installations. Combinations of offshore pipeline, drilling ships, platforms, sub-sea systems, sand islands and -ice island bases have been proposed. However, conditions in the Arctic are such that these methods may be difficult or impossible to implement. Problems exist with (1) the freezing of the Arctic Ocean surface for 9 - 10 months per year, (2) the movement of sea ice, (3) scouring of bottom sediments by ice islands and icebergs to great depths below the ocean bottom and (4) deep water channels. Any method which can avoid the problems associated with surface construction in these very adverse conditions merits detailed examination. One of the proposed solutions is to tunnel from a convenient or available access point to a point within the field, construct a chamber large enough to accommodate the drilling equipment and drill the development wells in a protected environment. Service and delivery lines would use the access tunnel and further tunnels and chambers would be constructed in a radiating pattern to develop the whole field. In order to determine the feasibility of underground construction in the North American Arctic, it is first necessary to understand the geologic and environmental factors which would affect such construction, to be knowledgeable concerning the problems and then to consider the techniques appropriate to the conditions which will be encountered, bearing in mind the need to minimize both con-

Jan 1, 1976

By Hetland Donald L.

Regional Tertiary formations and basins of local sedimentation which contain uranium deposits west of the Rocky Mountains are mainly of Oligocene, Miocene, and Pliocene age (fig. 1). The host rocks have been derived mainly from intrusive and extrusive igneous rock. The major host formations which cover broad geographic areas include the Esmeralda, Truckee, Humboldt, Thousand Creeks, Payette, Panaca, Cedarville, Coso, and San Joaquin Formations. Local areas of Tertiary sedimentation containing uranium deposits occur near Yuma, Safford and Artillery Peak, Arizona; Dillon and Canyon Ferry, Montana; Spokane Indian Reservation and Pend Orielle River, Washington; Topaz Mountain, Utah; Stanley Basin, Idaho; and Sonora Pass, California. Uranium deposits in these sediments have been classified into five categories based on environment (fig. 2). They are: (1) Deposits in lake sediments consisting mainly of water-laid tuffs; (2) Deposits in lake sediments intruded by volcanic plugs; (3) Deposits in lake sediments interbedded with arkoses near batholiths; (4) Deposits in coarse volcanic sediments in local sedimentary basins; (5) Deposits in arkosic conglomerates in local sedimentary basins.

Jan 1, 1969

By Chester A. Rowland, David M. Kjos

INTRODUCTION Mineral ore comminution is generally a feed preparation step for subsequent processing stages. Grinding, the fine product phase of comminution, requires a large capital investment and frequently is the area of maximum usage of power and wear resistant materials. Grinding is most frequently done in rotating drums utilizing loose grinding media, lifted by the rotation of the drum, to break the ores in various combinations of impact, attrition and abrasion to produce the specified product. Grinding media can be the ore itself (autogenous grinding - primary and secondary), natural or manufactured nonmetallic media (pebble milling) or manufactured metallic media - steel rods, steel or iron balls, or a combination of autogenous media and steel balls (SAG milling). This chapter covers rod and ball mills utilizing manufactured metallic grinding media. MILL DESIGN The interior surface of rod and ball mills exposed to pulp and/or grinding media are protected from wear and corrosion by rubber, metallic or a combination of rubber and metallic wear resistant materials. Rod and ball mills essentially draw constant power, thus are well suited for use of synchronous motors with power factor correction capabilities as drive motors. A net of approximately 120 to 130 percent of running torque is required to cascade the charge in these mills. The pull-in torque is about 130 to 140 percent with the pullout torque to keep the motor in-step (in-phase) generally in excess of 150 percent. When rod and ball mill are started across-the-line the starting and pull-in torques result in inrush currents exceeding 600 percent which possibly result in high voltage drops. To deliver 130 percent starting torque to the mill the motor design must take into account the maximum anticipated voltage drop. Motor torque decreases as the decimal fraction of the voltage available squared. E.g., a motor rated 160% starting torque with a 10% system voltage drop will deliver 160% x or 129.6% torque to its output shaft When it is not possible or practical to start a fully loaded synchronous motor across-the-line it is possible to utilize the motor's pull- out torque to start the mill. By using a clutch, normally an air clutch. between the motor and the mill, the motor is brought up to synchronous speed before the clutch is energized. If the motor has an adequate amount (175 or greater) of pull-out torque the pull-out torque starts the mill without major disruptions on the electrical system. Since the energy release at initial cascade of the mill charge is an inverse function of acceleration time, a minimum acceleration time of 6 to 10 seconds or more is recommended to prevent damage to the mill or the mill foundation. Economics at the time of plant design and mill purchase determine the drive to be used. The simpliest drive is the low speed synchronous motor with speeds in the range of 150 to 250 RPM connected to the mill pinionshaft by either an air clutch or flexible coupling. Using a speed reducer between the motor and pinionshaft permits using motors having speeds in the range of 600 to 1000 RPM. In this speed range, if power factor correction is not required induction motors can be used; squirrel cage where there is no restriction on inrush current; slip ring where a slow start and low inrush current is required. Air clutches can also be used to ease starting problems with squirrel cage motors. In some areas of the world induction motors and starters are less expensive than synchronous motors at a sacrifice of motor efficiency and power factor correction. Dual drives, that is two pinions driving one gear mounted on the mill, become economical for ball mills drawing more than 3500 to 4000 horsepower (2600 to 3000 kilowatts). Further developments of the low frequency, low speed synchronous motors with the rotor mounted on the mill shell or an extension of one of the mill trunnions could improve the cost picture for these "gearless drives", making them practical for large ball mills. The percent of critical speed, which is the speed at which the centrifugal force is sufficiently large to cause a small particle to ad- here to the shell liners for the full revolution of the mill is given in mill specifications. Critical speed is determined from the following: Where D is mill diameter inside liners (specified in meters). Cs is critical speed in RPM. When D is specified in feet

Jan 1, 1998

By Louis J. Trostel

Refractories, called the Hidden Industry by The Refractories Institute, provide the temperature and chemically resistant linings for the multitude of vessels that are used today in high temperature processes ranging from giant iron-making blast furnaces to industrial incinerators to petrochemical cracking units to the smallest furnaces used by the jewelry trade. While these refractory linings are absolutely essential to the proper functioning of these processes, the linings are almost always on the inside of the vessels and thus hidden from the eyes of the public. Refractories are defined in Standard C71 of the American Society for Testing and Materials (ASTM), titled "Standard Definitions of Terms Relating to Refractories," as "nonmetallic materials having those chemical and physical properties that make them applicable for structures, or as components of systems, that are exposed to environments above 1 000°F (538°C)." This criterion of ability to withstand exposure to environments above 538OC is the critical distinction separating refractories from other ceramics, fibers, and coatings applicable only at lower temperatures. In addition to resisting temperature, the refractories must with- stand abrasion, chemical and slag attack, resist thermal shock, and carry sustained structural stresses at high operating temperatures for as long as years. The most common methods of classifying refractories are by forming method and composition. First are the traditional formed and fired bricks, batts, and the associated multitude of special shapes. These refractories are usually formed at room temperature, dried, and then fired to high temperatures to develop the final properties desired. Other formed refractories are chemically bonded or resin or tar bonded. To complete the formed refractory matrix, some fired refractory bricks and shapes are subsequently impregnated with resins or tars. Physical dimensions of these formed refractories are classified into two general categories: standard sizes and special shapes. The standard sizes are those in common usage in the United States described in ASTM Standard C909 "Dimensions of a Modular Series of Refractory Brick and Shapes" based on the 38 mm basic module as described in ASTM Standard C861 "Determining Metric Dimensions of Standard Series Refractory Brick and Shapes." The most common size is the "9-inch straight" 228 x 114 x 64 mm (9 x 4 ½ x 2 ½ in.) of the "2 ½ -inch" series or 228 x 114 x 76 mm (9 x 4 ½ x 3 in.) of the "3-inch" series. Bricks of nonstandard sizes are referred to as special shapes. Their use is required in specific furnaces for particular requirements or applications. In addition there is the large and growing group of refractories sold as unshaped mixtures that may be formed into their final shapes at the application site. These unshaped mixtures are sometimes referred to as specialties. The mixtures are prepared to be hydraulically cast, plastic or wet rammed, dry rammed, or dry vibrated into their final shapes. Some are designed to be projected through nozzles (or gunned) onto their forms. The refractory mortars used to lay up the shaped refractories fall into this group referred to as specialties. Prepared refractory grains also are sold. These are usually calcined or fused materials that are subsequently crushed and sized to a variety of specific carefully controlled grain sizes or size distributions. These grains include calcined fire clay, dead burned magnesite, periclase (fused magnesia), dead burned dolomite, kyanite, tabular and fused aluminas, fused zirconia, fused mullite, and calcined alumina-magnesia spinel. The primary composition groups of refractories are the 1) alumino-silicate refractories made largely from fire clay and high- alumina materials, 2) silica refractories made from quartzites and ganisters, and 3) basic refractories from magnesia (or magnesite) and chromia (also referred to as chrome ore), alone and in combination, and dolomite. Special refractories include carbon, zirconia, zircon, high purity alumina, mullite, silicon carbide, silicon nitride, and some borides. In addition there are groups of special insulating refractories.

Jan 1, 1994

By James W. Mahar

The following paper summarizes our observations on building response to mine subsidence and techniques for mitigation of building damage. The subsidence cases are located in Illinois. The general description of the geologic and mine conditions are primarily for those sites. Data on building response and mitigation measures were collected under grants supported by the Abandoned Mined Lands Reclamation Council (AMLRC) of Illinois and the U. S. Bureau of Mines, in Twin Cities, Minnesota. Case histories include pit and sag subsidence primarily beneath abandoned room and pillar mines. The majority of the paper deals with structures affected by sag subsidence. Most of the structures are one and two story homes. The first section of the paper summarizes the typical geologic and mining conditions at the sites. Building response to pit and sag subsidence follows the first section. Emphasis is placed on the behavior of concrete and masonry foundations, and wood frame and masonry superstructures. The third section describes mitigation techniques used to prevent or minimize building damage. A summary of the observations and critical parameters is given at the end of the paper.

Jan 1, 1982

By V. B. Achanti, A. W. Khair

Introduction Laboratory studies were carried out at West Virginia University to investigate the rock-fragmentation mechanism of continuous miners using an automated rotary cutting simulator. The primary factors influencing the fragmentation process were found to be bit spacing, bit geometry, depth of cut and cutting-drum rotational speed. This paper presents a discussion of the effects of these parameters in achieving optimum energy consumption and minimizing dust generation during rock fragmentation. The removal of rock ridges/walls between adjacent grooves is analyzed with three hits mounted simultaneously on the cutting head, while the bit tip angle was varied from 600 to 900. Bit spacing was varied from 25.4 to 50.8 mm (1 to 2 in.) while the cutting process was assessed for varying cutting depths. Respirable dusts generated during the course of the experiments were analyzed utilizing cascade impactors. Assessment of these parameters has led to a better understanding of the cutting mechanism of continuous miners in terms of energy consumption and dust generation. A review of the literature revealed that a considerable amount of research has been carried out on rockcutting processes. Many authors agree that the mechanical cutting efficiencies of mining machines (e.g., continuous miners, shearers and road headers) are affected by a host of parameters. Some of these parameters are machine controlled, some are operator controlled, while others are uncontrollable. Efforts were focused on understanding the influence of parameters such as bit spacing, cutting depth, attack angle, bit type, drum speed, bit geometry (i.e., tip size, shape and tip angle) and rock type on the cutting process efficiency in terms of specific energy consumption and respirable dust generation (Strehig?? et al., 1975, Hanson et al., 1979, Khair et al., 1989). Roepke et al. (1976) in an attempt to study the dust and energy generated during coal cutting using point attack bits found that the dust and the specific energy consumed both decrease as the depth of cut increases. The four fundamental stages of dust generation luring rock fragmentation are identified by Zipf and Bieniawski (1989). Coal breakage by various types of wedges was assessed by Evans and Pomeroy (1966) in an extensive experimental study on British coals. Yet the industry today requires further attention and guidance to optimize the energy consumption and dust generation during the rockbreakage process. This paper attempts to give a better understanding of the influence of some of the parameters listed above and focuses on further improvement in the rock-cutting process. The specific energy consumed for different types of bits used and the respirable dust generated are analyzed in the context of the variation of a few other parameters. Laboratory investigation The experiments were performed in the Rock Mechanics Laboratories located at West Virginia University. A rock-cutting simulator designed and fabricated by Khair (1984) was utilized for this purpose. The details of this machine are available in the literature (see Khair 1984). For this study, a series of preliminary experiments was carried out to determine the optimum cutting frame advance speed. This was intended to facilitate a maximum cut depth of 31.75 mm (1.25 in.) at an advance rate of 0.525 mm/s (0.0207 ips) for all types of bits being used and various bit spacings being considered. To look into the cutting-process efficiency of a continuous miner in the laboratory, several parameters of influence are being considered. Besides the bit-geometry parameters, machine- and operator-controlled parameters, such as spacing of bits on the cutting head, the cutting head rotational speed and the total cutting depth during an experiment, are varied. At the time this paper was written, only part of the completed experiments were ana¬lyzed, and a number of experiments were still being carried out following an orthogonal fractional factorial experimental plan to assess the effect of all of the above¬mentioned parameters on the cutting efficiency in terms of energy consumption and dust generation. Three different types of tip angles, namely, 60°, 75° and 90°, and two different tip sizes, namely, diameters of 7.94 and 24.61 mm (0.313 and 0.969 in.), were used. At

Jan 1, 1999

By Al. Valero

This paper quantifies in universal units (energy units), the annual decrease in the mineral endowment of the planet. This is done for some important extracted non-fuel minerals, namely aluminium, cobalt, chromium, copper, gold, lead, uranium and zinc and is compared with the depletion figures of conventional fossil fuels. The results of this study reveal that each year, the decrease of the global non-fuel mineral bonus provided by Nature is 2 to 3 orders of magnitude greater than the loss associated to the burning of fossil fuels. Particularly for 2008, the depletion in mineral wealth of the studied commodities was about 20 times greater than that of fossil fuels. The assessment methodology is based on the Second Law of Thermodynamics. It quantifies the useful energy (exergy) required to concentrate a mineral from a completely dispersed state in the crust, to the conditions of composition and concentration found in the mines. Exergy can be a useful measure for quantifying the mineral depletion caused by man, as it takes into account the main physical features that make minerals valuable: composition and concentration. This analysis enhances and puts numbers to the importance and necessity of material reuse and recycling.

Jan 1, 2011

By Jamal Rostami, Ataollah Rahbar, Jürgen Paulzen

"Uma Oya Multipurpose Development Project is located in South West Sri Lanka. This project, among many components, involves a 14 km headrace tunnel in very hard and abrasive igneous rocks. The tunnel is under construction by a 4.4 m diameter double shield TBM. The headrace tunnel has already reached 5km milestone and has passed through some reaches of tunnel in very strong intact rocks with no joints. Low penetration at high thrust load has caused frequent stoppages for cutter change leading to low utilization and advance rates due to low cutter life. The original machine was dressed with 27, each 432 mm (17 inch) diameter, 19 mm (3/4 inch) tipped disc cutters. However, various cutter diameters of 432-457 mm (17-18 inch) and cutter tip widths 13 to 19 mm (0.5-0.75 in), have been tried to see if cutter life and penetration rates could be increased. This paper will review the history of the project, the geology of the site, along with TBM performance and cutter life. It will focus on frequency of different cutter failures encountered in various ground conditions. Also, results of using variation of cutter diameter and tip width to cope with the hard rock conditions and their results in increasing machine productivity will be discussed. This allows for better understanding of parameters controlling disc wear/life and leads to better cutter management for more efficient operation of hard rock TBMs in similar conditions. INTRODUCTION The Uma Oya Multipurpose Development Project (UOMDP) lies in the south-eastern part of the central highland region of Sri Lanka. The Multi-Purpose Project Of Uma Oya is planned to convey water from Uma Oya to Kirindi Oya Basin for hydroelectric energy generation includes Puhulpola RCC Dam on the Uma Oya river, Dyraaba RCC Dam on the Mahatotilla Oya river, a conveyance tunnel from Uma Oya to Mahatotilla Oya (L=3750m), a long feeder tunnel from Mahatotilla Oya to Kirindi Oya river. The feeder (or power) tunnel Lot consists of a 15554 m long headrace tunnel (HRT), the surge shaft and tank on the upstream of the vertical shaft, a 650 m vertical shaft with steel lining, and an underground powerhouse and a 3650m tailrace tunnel (TRT)."

Jan 1, 2016

By John N. Murphy

In fiscal 1996, the US Congress directed that the US Bureau of Mines (USBM) be closed. Certain functions were reassigned to other agencies. The remaining employees were separated and the unoccupied sites were decommissioned. As a result, 12 locations were closed and about 1,200 employees were terminated in March 1996. About 600 employees at five locations were reassigned to other federal agencies. This article provides a summary of the continuing functions, the agencies involved and the points of contact for each continuing function. The functions that were discontinued are also identified. The functions that have been maintained and transferred to other agencies are: ? Portions of USBM's Mineral Information and Analysis program formerly conducted in Washington, DC and Denver, CO were assigned to the US Geological Survey (USGS). ? The Mineral Land Assessment program in Alaska (Anchorage and Juneau) was transferred to the US Bureau of Land Management (BLM). ? The Health and Safety Research program in Pittsburgh, PA and Spokane, WA was reassigned on an interim basis to the US Department of Energy (DOE). In fiscal year 1997, it was permanently assigned to the National Institute for Occupational Safety and Health (NIOSH). NIOSH is part of the Centers for Disease Control and Prevention within the US Department of Health and Human Services. ? Environmental Research at Pittsburgh, PA was assigned to DOE. ? Materials Research at Albany, OR was assigned to DOE. ? The helium program was assigned to BLM, where it will be managed pending privatization. ? Coal and noncoal mine maps were transferred to the Office of Surface Mining Reclamation and Enforcement (OSMRE). The following locations were closed: ? Research centers in Denver, CO; Minneapolis, MN; Reno, NV; Rolla, MO; Salt Lake City, UT and Tuscaloosa, AL. ? Field operations centers in Denver, CO and Spokane, WA. ? Washington, DC headquarters office. To provide a concise picture of all of the affected functions, the following is a synopsis of the USBM program functions and facilities immediately before the closure. There were two principal programs: information and analysis, and research.

Jan 1, 1997

By S. Chander

The use of various electrochemical techniques to study mechanisms of sulfide mineral- flotation reagent interactions is briefly reviewed in this paper. Prior to such studies it is desirable to thermodynamically determine solution conditions favorable for formation of hydrophobic species deemed to be responsible for flotation. The thermodynamic equilibrium involving both the stable and metastable species can be conveniently represented by an Eh-pH diagram. Thermodynamics can also be used to predict conditions where a mineral might not float if depressants are present. Under favorable conditions of flotation there is competition between reactions leading to formation of hydrophobic species with reactions that lead to formation of hydrophilic species. Due to the sluggish nature of the reactions involving sulfide minerals, a knowledge of the kinetic behavior of the system is necessary. Electrochemical methods of investigation are wed in laboratory studies to (1) control the state of oxidation, (2) determine the type and amount of electroactive species present at the mineral surface, and (3) study kinetics of electrode processes. By combining electrochemical techniques and wetting measurements the identification of hydrophobic species that might be present at the mineral surface could be achieved. Both contact angle measurements at mineral electrodes or flotation in a cell equipped with a particulate bed electrode can be used for the wetting measurements.

Jan 1, 1987

By J. Herbst, H. B. Treweek, V. R. Degner, G. Poling

Current mineral industry trends toward handling the high tonnages of lower grade ore and tailings retreat lead to a continuing need for large volume flotation cells. The benefits which accompany the larger cell flotation circuit include reduced capital cost, less mill floor space, reduced operational complexity, and less maintenance, provided the metallurgical performance and solids suspension capability of the cell are not compromised. This study reviews development considerations pertinent to large mechanical air induction type flotation cells from the standpoint of cell internal hydrodynamic characteristics and metallurgical performance. While the importance of process related factors such as chemical usage, pH control, solids size and loading, and circuit arrangement cannot be denied, this study will emphasize the relationship of cell size (volume), mechanism geometry (impeller diameter), and mechanism operating conditions (rotor speed and submergence), to air transfer, liquid circulation, liquid "rise velocity" and mechanism power draw. Specific hydraulic performance maps for large capacity 300 and 500 cu ft flotation cells will be reviewed in terms of the relationship between the operational variables and the air and liquid flow conditions within the cell. Metallurgical results, obtained under plant operating conditions for 300 and 500 cu ft cells, are included to illustrate the metallurgical performance similarity of flotation cells which follow hydrodynamic scale-up criteria set forth in this investigation.

Jan 1, 1976

By Andrzej Frycz

The development of the theory of reliability creates more and more possibilities of its application in different domains of technics. The methods evolved to date, both theoretical analysis of the engineering systems and investigations techniques in practice can be put in use a d translated from one science to another one [1,3,7J . It needs to consider the specific of the different sciences. But it is necessary to take account of the specific characteristic of each line of science. The reliability investigations needs, justified in technical and economical viewpoint appear too in mine ventilation technics and systems. The mine ventilation system is a complex of workings and ventilation plants, which serve to supply the networks with a sufficient quantity of fresh air from the atmosphere and then carry off the vitiated air. The condition necessary for a ventilation system to perform definite task is the correctness of all its elements, that is a capability to preserve in a expected range of tolerance, the values of basic parameters. The element of a system which ceases to work correctly is called failed. The basic parameter of all elements of a ventilation system is the characteristic curve, pressure loss - air quantity relation ?p = f(Q) (1) This curve concerning the workings and ventilation stoppings is given by the formula: ?p = R Q2 (2) thus the resistance R (of the workings or stoppings) may be taken as a characteristic parameter. The course of this characteristic f(Q) will be given in a complex form in concern with fans, ejectors, air curtains. The failure of a ventilation plant or working is therefore an event, relying on a change of its characteristic, thus for a definite time the losses of the plant's or working's capability set in for the fulfilment of its function in the ventilation system. The failures are divided in viewpoint of their nature on sudden and progressive. We are in concern with the sudden failures which are characterised by a violent change of the ventilation element parameter for example a fall of roof, or silt up of the working, opening or failure of the ventilation stopping, the stand-off of the fan or ejector etc. We distinguish two kinds of failures on the viewpoint of their action on the air flow: the "opening" failure and "closure" failure. The prevalence of factors, which causes the failures is in connection with the intersection in the mine of roads of haulage, roads of underground transport of materials and lining elements, roads of people motion with airways, as also depends on the rock pressure reaction on the workings lining and plants placed there. Other factors will yet be decisive upon supply decay of fans, ejectors and curtains. The appearance of failure of the ventilation element is therefore of random nature and determines the change of the element, when it is passing from operating state to unoperate. Qualifying the ventilation system element to one of these states is easy, when the characteristic change is clear and occurs suddenly, that was assumed. The investigations conducted by Patrushev and Karnaukh [91 in concern with the ventilation stoppings resistance change in the case of their opening, had shown the possibility of resistance value change in the range of several hundreds higher.

Jan 1, 1980

By S. Orr

Flow in heaps and dumps is a two-phase flow phenomenon, though for many applications it could be simplified as unsaturated flow. Unlike saturated flow (typical of ground water flow), where permeability is independent of other hydraulic parameters, unsaturated flow permeability depends on the degree of saturation and/or on capillary pressure. Several recent field studies suggest that flows in heaps and dumps tend to concentrate in preferred pathways, bypassing much of the ore. Different preferential flow phenomena are triggered, promoted and influenced by different heap structures, by pretreatment, by the composition of the leach solution and by application rates and schedules. The structure of heaps and dumps is determined and affected by every stage of their construction -from blasting to crushing to conveying and stacking of the material. History of heap construction and operation combined with monitoring, mapping and certain field tests can reveal patterns of flow and transport in a given heap and can shed light on the physical mechanisms behind it. Such insight can provide a first cut on heap leaching enhancement by either eliminating or bypassing physical barriers to flow and leaching. Based on the understanding of the heap structure, advanced flow and transport models can be constructed and further enhance the insight. This insight is essential for understanding cause and effect and can provide a basis for decision making. Further, based on the physically-based models, an intelligent control agent, such as MRDS1, can learn and build a self-learning representation (or a model) of the complex heap leaching system, followed by dynamic optimization and planning of heap leaching and heap rinsing.

Jan 1, 2003

By R. R. Graham

Echo Bay Minerals operates a 650 tpd gravity float gold circuit at their Manhattan facility. The objective of this paper was to document the gold recovery by size distribution. This was accomplished by studying the material balance of each size fraction as it progressed through each gravity Circuit separator. It proved to be an impossible task. Figure I depicts the gravity circuit. The gravity cyclone underflow goes to two duplex Pan American type jigs. The jig overflow reports to the OK Flash Float Cell. The cyclone hutch product is reground and goes to a full size wilfly table. The rougher table concentrate reports to a pilot size Wi1fly cleaner table. The cleaner and rougher table tails circulate back to the jig feed. The gravity circuit was composite sampled for two to four hours per day for four days. Each sample was taken every 20 minutes. Each composite sample was filtered, dried, repu1ped, and screened through a wet/dry screening procedure. Each size fraction was checked for gold value by fire assay fussion technique. A material balance was run on each size fraction. The tables listing the results are enclosed.

Jan 1, 1989

By S. Zamna, M. E. Defoe, Franklin T. Davis, Earl Rau, Yarroll. Warren H., Paul D. Chamberlin

This section contains a description of the ore processing methods of the walled industrial minerals that are not described in major sections of the book. Table I contains the production figures for each of these commodities in the United States and the world. Specifications for concentrates or final mineral product are also summarized as well as prim for them at the time the section was written. In each chapter an attempt has been made to provide the reader with information on the common commercial mineral or minerals involved with the commodity, some of the uses. the processes used to recover and concentrate the minerals, as well as geographical areas where these process are utilized.

Jan 1, 1985

By Edie Trimmer

Utah statute defines sovereign lands as "those lands lying below the ordinary high water mark of navigable bodies of water at the date of statehood, and owned by the state by virtue of its sovereignty." The lands within the bed of Great Salt Lake (GSL) are, by this definition, sovereign lands, acquired at statehood in 1896 in accordance with the "equal footing" doctrine, granting each state control and ownership of navigable waters and the lands underneath those waters within its borders. Under public trust doctrine, the state, as trustee for the people, bears responsibility for preserving and protecting the right of the public to use of the waters for navigation, commerce, fishing, recreation, and wildlife habitat. Also by statute, sovereign lands are defined as "state lands," to be managed by "multiple use sustained-yield principles." The Division of Forestry, Fire and State Lands is given management authority for sovereign lands and, as manager, has responsibility to prepare comprehensive plans, initiate studies of the lake and its resources, implement comprehensive plans through state and local entities, and coordinate the activities of various divisions within the Department of Natural Resources (DNR). The Division of Forestry, Fire and State Lands also has responsibility for management of mineral leasing on sovereign lands. The many resources on the lake--water, minerals, wildlife, recreation, archeological and historical values--are managed by as many state agencies which occasionally creates conflicts. The brines of GSL contain several ions that crystalize into valuable minerals during evaporation. The major ions in the lake are, in order of relative abundance, chloride, sodium, sulfate, magnesium, and potassium. Mineral products which are currently extracted from lake brines are sodium chloride, magnesium chloride brine which can be sold as flake magnesium chloride or further processed into magnesium and chlorine gas, and potassium sulfate. Mineral products which have potential for extraction include gypsum, sodium sulfate, and trace amounts of lithium, boron, and bromine. The GSL contained an estimated 4.3 billion short tons (st) (3.9 billion metric tons [mt]) of dissolved salts in 1998. Utah Geological Survey (UGS) estimates of the dissolved salt content in GSL have fluctuated from 4.0 to 5.5 billion st (3.6 to 5.0 billion mt) due to the dynamic conditions in the lake as salts are precipitated and redissolved, and due to the diversion of brines from GSL, such as the West Desert Pumping Project. The lake has four areas of varying salinity, separated by dikes or other man-made structures: north arm and Stansbury Bay brines at near saturation (25 to 27 percent total dissolved solids [TDS]); the main body of the south arm with concentrations ranging from 7 to 15 percent TDS as lake elevations fluctuate; the waters in Farmington Bay at approximately 3 to 5 percent TDS; and Bear River Bay at <1 to 7 percent TDS. The percent TDS in Bear River Bay fluctuates with lake level, and changes in Bear River inflow. The transfer of salts from the south arm to the north arm has raised questions about the viability of the mineral and brine shrimp industries. The UGS and the U.S. Geological Survey (USGS) continue to monitor salinities at designated sites on the lake to document changing lake salinity. A recurrent theme is that placement of dikes and diversions can have significant and rapid impacts on various conditions in the lake. Hydrocarbon resources on the lake are significant, but presently undeveloped. The hydrocarbons are low gravity (4 to 9 degree API) and tar-like, contain high nitrogen concentrations, and up to 12 percent sulfur. The unusual characteristics of the oil have been the subject of studies by chemists at Weber State University and University Louis Pasteur de Strasbourg. However, these resources are difficult, and at present, uneconomic to extract using current technology because of the nature of the hydrocarbons, and production in "an offshore, highly saline environment." Oolitic sand deposits make up many of the beaches and shorelines around the lake. Because of their high calcium carbonate content, oolites have been used by Magnesium Corporation of America (MagCorp) and its predecessors for acid neutralization and dike construction. Oolites are also used in very minor amounts in flower drying. The Utah Division of Oil, Gas and Mining reports up to 130,000 st (118,000 mt) mined annually by MagCorp from U.S. Bureau of Land Management (BLM) lands adjacent to GSL. Currently, there are twelve producing mineral leases which generated slightly more than $1,000,000 in royalties during calendar year 1998. IMC Kalium Ogden Corp. (IMC Kalium) produces potassium sulfate and magnesium chloride from brines concentrated through solar evaporation in Bear River Bay and Clyman Bay. By-product sodium chloride is transferred to IMC Salt, which packages and sells the salt. MagCorp produces magnesium metal from brines concentrated in Stansbury Bay. Cargill Salt produces sodium chloride from brines provided by MagCorp under a lease agreement. Morton Salt produces salt at the southeast end of Stansbury Island. Lastly, North Shore Limited produces cocentrated brines for use in dietary and mineral/vitamin supplements near Spring Bay in the north arm of the lake. Producers of magnesium, potash, and salt from GSL contribute significantly to the value of metals and industrial minerals in Utah. Together these companies contribute approximately $240 million in gross value, or 18 percent of the value of the state&apos;s nonfuel mineral production. Most of this production is exported.

Jan 1, 2001

By L. R. Shotwell, C. F. Voss, R. J. Bastian

Pacific Northwest Laboratory (PNL) currently supports the U.S. Department of Energy&apos;s Office of Civilian Radioactive Waste Management in developing and evaluating analytical methods for assessing the suitability of sites for geologic disposal of high-level radioactive waste. The research includes consideration of hydrological, geomechanical , geochemical , and waste package components and the evaluation of the degree of coupling that can occur between two or more of these components. The PNL effort and those of other research groups investing potential waste sites in the U.S. and abroad are producing a suite of computer codes to analyze the long-term performace of the proposed repository sites. This paper summarizes the ongoing research in rock mechanics at PNL involving flow through jointed rock. The objective of this research is to develop a methodology for modeling the coupled mechanical-hydrological process of flow through joints and then attempt to validate a "simple" model using small -scale laboratory test data as a basis for judging whether the approach has merit. This paper discusses the laboratory tests being conducted to develop s joint behavioral constitutive model for the numerical method under development and the modeling approach being considered.

Jan 1, 1986

By Steven A. Moreno

Geochemical returns from commercial analytical laboratories are often delayed because of postal and other bulk distribution inefficiencies. Consequently, minerals exploration programs are handicapped due to insufficient time for treatment, analysis, and diagnosis of the data. The minerals industry lacks a system for rapid transmission of geochemical data which allows immediate entry into statistical and plotting routines. Over the past three years, Houston International Minerals Corporation (HIMCO) has developed a computer-based system to receive, treat, and distribute geochemical data. In the past two years, Bondar-Clegg (Denver) and Chemex (Vancouver) have developed systems to transmit&apos; data directly to HIMCO via the world-wide Boeing Computer Services (BCS) network. The main benefits to HIMCO have been ten less days for reporting turnaround, ten less days for keypunching, less data handling, accuracy. The benefits to the laboratories have been improved in-house data management, reporting, and HIMCO&apos;s increased geochemical activity.

Jan 1, 1982