Search Documents

By A. R. Przybylek

A fluid bed dryer has been designed for a nonconventional application to upgrade the value of fine anthracite culm and silt recovered from culm banks and anthracite tailings pond beds. This material can be seen as large spoil piles scattered throughout the anthracite coal regions of Eastern Pennsylvania. Engineering of the system commenced in December of 1986 and at this writing start-up is scheduled for late October or early November of 1987. This paper will focus on generalities concerned With system design and operation, and qualify the differences from conventional fluid bed coal drying systems.

Jan 1, 1988

By C. Roldan, C. Garcia, J. D. Miller, C. L. Lin

The ultimate recovery in a heap leaching operation is related to the degree of exposure of the valuable minerals in comminuted particles. Recently, high-resolution cone beam x-ray microtomography (XMT) has been used to determine this parameter. XMT technology consists of examining the extent of mineral exposure for each size fraction of ore in 3D, then, by algebraic calculations, the ultimate recovery can be estimated for different particle size distributions (PSD). To confirm the usefulness of the XMT technology for mineral exposure analysis, column tests were performed to determine ultimate recovery using three PSDs for two composites obtained from the copper heap leaching operation at Zaldivar-Chile.

Jan 1, 2003

By Mona M. Fawzy, Ahmed A. Eliwa, Ebrahim A. Gawad, Ahmed H. Orabi, Amal E. Mubark

The growing demand for rare earth elements (REEs) has led to numerous recent studies to recover these elements from various bearing ores and wastes. Therefore, the recovery of REEs from Ras Baroud polymetallic concentrate has been investigated in the current study. Physical beneficiation for the Ras Baroud pegmatite sample was carried out, yielding a concentrate for euxenite (Y), fergusonite (Y), xenotime (Y), monazite (Ce), allanite, thorite, uranothorite and Hf-zircon, which resulted in raising the concentrations of REEs, Th, Zr, U and Ti in the sample. Fusion digestion processes with sodium hydroxide were studied using the conceived predictive diagonal (CPD) technique. The three experimental digestion groups proved the dissolution of 99.9, 95.6, 99.9, 52.5 and 0.47 percent for REEs, Th, U, Ti and Zr, respectively, under fusion conditions of 723 K, 120 min, 1/1.5 ore-to-alkali ratio, and smaller than 100-μm particle sizes. Fusion kinetics, isotherms and thermodynamics were investigated using several suggested models, namely, pseudo reversible first order, uptake general model and shrinking core model, which matched well with the experimental digestion results. Selective recovery of actinide content from the REE content of the digested concentrate chloride solutions was accomplished using solvent extraction with di-2-ethyl hexyl phosphoric acid. About 99.9, 99.9 and 4.2 percent extraction efficiencies for Th, U and REEs were realized, respectively, using 0.3 mol/L solvent concentration in kerosene as a diluent, 1/2 organic-to-aqueous ratio, aqueous pH of 0.2 and contact time of 15 min. Thorium and uranium ions were stripped with 2.5 mol/L sulfuric acid solution with 94 and 98 percent stripping efficiency, respectively. A highly purified REE precipitate was obtained from the raffinate solutions. Zircon mineralization tailings were obtained as a byproduct through the alkaline digestion process.

Oct 1, 2024

By W. Petruk, D. B. Sikka

Lithium-bearing lepidolites from three deposits in the province of Goias, Brazil, were investigated to determine whether there is a correlution between the lithium content of the mineral and the color of lepidolite and associated tourmaline. Such a correlation can be a useful guide to field geologists for outlining high-grade lithium ore zones. It was found that mauve-pink lepidolite associated with pink tour-maline, and brownish lepidolite associated with black tourmaline have high lithium contents, but that the color of lepidolite is not due to lithium. The pink color of lepidolite and tourmaline is likely due to Mn3+, and the brownish tint of lepidolite and black color of tourmaline to Fe3+. Lepidolites appear to be lithium- rich when the lepidolite and associated tourmaline contain relatively high amounts of Mn3+ and/or Fe3+.

Jan 1, 1988

By David Williamson

In the post-World War II years, metals analysts and statisticians have tracked the demand for metals in line with changes in Organization of Economic Cooperation and Development (OECD) industrial production (IP) growth rates, Williamson said. This was because the correlation between IP growth and metal demand was reasonable. "However, the correlation was exaggerated," he said. During times of expanding IP growth, metal demand increased at a faster proportional rate than IP growth. This was probably due to industry restocking in anticipation of growing demand at the start of each economic cycle. Conversely, metal demand would slacken at a greater rate than would be suggested by negative IP growth as industry destocked to reduce costs. Nonetheless, he said, a reasonable correlation could be painted between IP growth over the longer term and metal demand. "Yet, although this correlation has stood well since the last world war, it has been based on the fact that the bulk of the world's IP growth stemmed from the industrialized countries of the western world, lately including Japan," Williamson said. The so-called "developing world" had been of little consequence. The Soviet Union and other communist bloc countries were deemed to be closed, self-contained entities that, for each metal, would either be net exporters or importers, he said. These quantities would be used by analysts to calculate the overall supply/demand equation for the western world only and to deduce whether a commodity was in shortage or surplus. It is now believed that this method of projecting total world supply and demand for raw materials is outdated, Williamson said. It does not take into account the worldwide political changes that have occurred since the collapse of communism and the revitalization of China. "It is no longer appropriate to assess global balances for raw materials on the basis of three economic blocs," he said, including the western world, developing world and communist bloc. Rather, global balances need to be projected on a global basis. In this regard, since the collapse of communism and the removal of many other totalitarian regimes, capitalist forces are attempting to satisfy the expectations of the great mass of the world's poorer people, Williamson said. Such people, usually located in Asia, Africa and Latin America, have aspired to the same standard of living as people living in western Europe, North America and Japan. "Now, with free market forces at work, their aspirations will start to be met." Consequently, the demand for metals and other raw materials will now rise at a much faster rate. The production of raw materials has to keep pace with rising IP in the developed world. It will also have to keep pace with the demands associated with the rising expectations of increasing populations in the developing world, as well as from within the old communist bloc countries.

Jan 1, 1997

By Normand Tassé

Reactive barriers, which consume oxygen, are prospective though unconventional alternatives to physical barriers for Acid Mine Drainage prevention. However, a reactive barrier implies a problem of duration. Pore gases were analysed in several wood waste piles in order to understand the factors which control wood degradation and help to determine the effective life span of such a cover. Long term efficiency seems to strongly depend on the degree of water saturation at the bottom of the pile, likely because the development of a microbial biomass in such an environment helps to keep the amounts of nutriments and readily metabolizable organic substrates at a high level, which in turn promotes oxygen consumption.

Jan 1, 2000

By V. Rajaram

V. Rajaram's paper does not accurately reflect the status of Eastern oil shale development as it stands today. Today, there are numerous firms and research organizations pursuing development of the Eastern oil shale resource. Details of the current projects can be found in the symposium proceedings for the 1985 Eastern Oil Shale Symposium held in Lexington, KY, in November 1985. Additionally, the comparison of the Paraho and HYTORT processes is invalid because the HYTORT process design used it not an accurate representation of the HYTORT process. I will briefly address this point. It is disconcerting to see the author reference hydroretorting work conducted at the Institute of Gas Technology (IGT) (circa 1978) in the introduction, which indicates hydroretorting (the HYTORT process concept) yields of up to 250% of the Fischer Assay oil yield, and then turn around and base the remainder of the paper on the 1981 "Synthetic Fuels From Eastern Oil Shale Report," which depicts the HYTORT process as yielding only 115% of Fischer Assay. Indeed, work conducted at IGT to 1981 indicates commercial oil yields for the HYTORT process would be in the range of 200% to 210% of Fischer Assay. A more thorough literature search by the author would have yielded a 1981 publication by Schora et al., entitled "Update on the HYTORT Process" presented at the Symposium on Synthetic Fuels From Oil Shale in Nashville, TN, October 1981. This paper thoroughly discusses the shortcomings of the referenced study with respect to the HYTORT process. For the interested reader, I can also recommend a June 1984 report entitled "An Economic Comparison of Five Process Concepts for Using Eastern Oil Shale," published by Los Alomos National Laboratory (LA-10106-MS, Parkinson et al., NTIS No. DE84-015981). This study applies a realistic HYTORT design (circa 1982) and indicates that HYTORT is the most econom¬ical method of processing Eastern oil shales (about $20/bbl less than Paraho). Additionally, completion of the HYTORT feasibility study in June 1983 by Phillips Petroleum Co., Bechtel Group Inc., HYCRUDE Corp., and IGT has resulted in development of designs that will make the use of HYTORT on Eastern oil shales even more economic. HYCRUDE Corp., a second-tier subsidiary of IGT, is involved in commercialization and licensing of the HYTORT process and is active in efforts to develop the Eastern oil shale resource. As such, I am disappointed to see outdated material that has the potential for adversely affecting development of Eastern oil shale resources published in MINING ENGINEERING. I can only hope that this response will serve to mitigate any negative opinions that may have been formed. Today, activity in commercializing Eastern oil shales dominates the oil shale scene in the US and indicates a realization of the potential for these shales. Reply by V. Rajaram I appreciate the updates on the HYTORT process provided by R.C. Rex, Jr. I hope that Hycrude's work will lead to the funding of a pilot plant to demonstrate that yields of greater than 200% of Fischer Assay can be achieved in a commercial plant using eastern US oil shales.

Jan 1, 1987

As mentioned in chapter 8, one of the objectives of the budget is to provide a mechanism for ongoing measurement and control of the production operation. The budget shows expected performance. Actual results are compared to this benchmark to evaluate past performance and to direct future activities. The variances between budgeted and actual results identify specific activities that did not perform as expected (whether negatively or positively). Managers who use variance analysis are essentially applying a management- by-exception philosophy. Individual organizations will determine variances that reflect their own processes and managerial interests, but these variances all follow the approach outlined here. Firms will also vary in the extent to which variances are reported. Some firms use a few variance measures for the overall production organization whereas others calculate variances for individual departments or even individual work areas. As mentioned in chapter 5, it is important to distinguish between controllable and noncontrollable costs when using budgets for control and evaluation.

Jan 1, 1999

By P. L. Webster, S. D. Thompson

Sevim and Wang (1988a) have presented a model for designing haulage systems in underground coal mines. The authors contend that their model uses a heuristic algorithm to optimize various haulage system parameters. In reality, it would be nearly impossible to optimize a haulage system, because mining plans are uncertain and often change with respect to time. Therefore, haulage system design poses both a stochastic and a dynamic design problem, and its optimization appears to be well beyond the scope of heuristic algorithms. In regard to the authors' design model and its practical significance, a number of additional issues warrant further discussion and clarification. These issues include: l) their model's alleged advantage over simulation models, 2) the correctness of their belt network design, 3) the correctness of their bunker design, 4) the necessity of their proposed bunker clearance policies, 5) the correctness of their shaft-bottom bin design, and 6) the

Jan 1, 1991

By J. Bouchard, V. Aubé, A. Desbiens, R. del Villar

The metallurgical performance of column flotation is determined by the concentrate grade and recovery. Although the former can be continuously measured using an on-stream analyzer, the latter must be estimated by a material balance calculation based on seldom verified steady-state assumptions. Consequently, the automatic control and optimization of flotation columns should be performed using secondary variables having a strong influence on the metallurgical performance, such as froth depth, gas hold-up or bubble surface area flux and bias. The aim of this paper is to present a method to get froth depth and bias measurements using virtual sensors. Fractional factorial experiment design for the neural network calibration of the bias sensor, pilot plant results, and eventual industrial applications – including the possibility of achieving effective real-time optimization from bias and froth depth measurements – will also be discussed.

Jan 1, 2003

By R. E. Greuer

The design of mine fire emergency plans requires that the contamination of mines by fumes, and the mutual interaction of fires and ventilation systems be pre-calculated. Several computer models were developed by the Bureau of Mines for this purpose during the last decade. The models advanced in sophistication from the transient-state simulation of fume concentrations for the early stages of a fire to the steady-state simulation of airflow rates, concentrations, and temperatures for fully developed fires, and finally to the complete transient-state simulation of fires and ventilation systems. The principal features of these models are described.

Jan 1, 1989

By Douglas J. Uhren, Gary W. Gilbert

This paper describes the risk elements associated with difficult glacial geology, including boulders, heavy groundwater inflow, and potential running soils all coupled with a potentially corrosive service environment. The matrix workshop for the 168-inchfinished diameter sanitary sewer interceptor tunnel in Columbus, Ohio is assembled with the Design Team and the Owner’s design, operations, and fiscal staff. Corrosion protection alternatives are compared against cost and non-cost parameters with relative risk and weighting factors assigned. The Owner working in cooperation with the Design Team uses the matrix workshop to se

Jan 1, 2001

By M. E. Rossi, V. Camacho

Reconciliation of production information is critical to evaluating the effectiveness of predictive models that would allow for the optimization of mining operations. Whether mining open pit or underground, mine-to-mill reconciliations can be one of management's better tools for the performance of proper accounting. Such reconciliations can also be a very useful tool in evaluation and optimization. This paper proposes a set of criteria and objectives for a typical reconciliation program. This paper also presents a stepwise, logical approach to performing reconciliations and discusses the benefits associated maintaining good information. It also highlights some of the potential pitfalls involved and the methods used to avoid collecting misleading information. These issues are illustrated with an example of a model-to-mine-to-mill reconciliation program that is being implemented at an operating mine. The program involves multiple predictive models (long-term and short-term block models), feed from three open pits and one underground mine, in addition to intermediate stockpiling, for a total of 23 mill streams. This paper presents a summarized version of this reconciliation program and its initial results as implemented at Minera Michilla S.A.

Jan 1, 2000

By Ch. Apostolaki

Eighty samples from Roman wall paintings from ancient Corinth were studied by means of optical and scanning electron microscopy coupled to an energy dispersive analyzer, X-ray diffraction and image analysis techniques. The goals of the study were the identification of the exact nature of the pigments and the technical features of paint application (binding medium, adherence to plaster, thickness of the pigment layer), which would provide evidence about the painting technique (fresco or secco). The main plaster is calcitic with secondary calcite as a cement binder to the primary calcite grains. All pigments, except Egyptian Blue, were naturally occurring ochres or pigment minerals, such as limonite, goethite, hematite for yellow, brown and red hues, cinnabar for red hues and celadonite for green color. The presence of specific elements such as Ni and Cr or minerals such as olivine, in the yellow, brown and red pigments, gave an indication about the provenance of the original pigments, which seems to be from Cyprus. The black color was represented using charcoal. It seems, finally, that for the pigment application the fresco technique was used, while secco is also apparent.

Jan 1, 2006

By H Sohn, R. R. Fernández

Microscopic gold inclusions in sulfide minerals cannot typically be extracted by conventional cyanidation. The gold ore must be pretreated to oxidize sulfide minerals associated with gold and to remove other minerals and chemical compounds that interfere in the cyanidation leaching process. The recovery of gold from refractory sulfidic-carbonaceous ores after roasting pretreatment was studied. With the addition of an oxygen-containing gas (e.g., air or oxygen-enriched air), sulfides of iron, zinc. copper and other metals are tramformed into solid oxides or sulfates and gaseous sulfur dioxide at elevated temperatures (e.g., 400° to 800°C). When the sulfides are oxidized, individual particles lose internal volume and become porous, allowing leaching solutions access to the gold. The structural characteristics of the calcine have a strong influence on the eventual recovery of gold by cyanidation. These characteristics are strongly dependent on the roasting conditions and roasting method. The optimum combination of particle size, roasting temperature, reaction time and oxygen concentration in the off-gas was determined for a typical refractory sulfidic-carbonaceous ore from the Carlin Trend in Nevada. The tests were run using a 150-mm laboratory rotating tube furnace and 160- and 200-mm.fluid-bed pilot roasters. Laboratory results indicated that the maximum gold extraction was 92%, with the head and the leach residue containing 5.7 and 0.4 g/t (0.166 and 0.013 oz/st) Au, respectively. The maximum extraction was achieved under the following roasting conditions: a top particle size of 150 yin, a residence time of 2 hrs, a roasting temperature of 475°C and with 40% oxygen (by volume) in the off-gas. Similar results were obtained from circulating fluid bed (CFB) pilot-plant testing. The maximum gold extraction was 90%, with the head and leach residue containing of 5.1 and 0.5 g/t (0. 149 and 0.015 oz/st) Au, respective) v. These results were achieved with the same particle size and oxygen concentration as in the laboratory testing but with the roasting temperature of 500 ° to 525°C and a residence time of 30 min.

Jan 1, 2000

By S. P. Mehrotra, P. C. Kapur

A phase-species classification is suggested for the mathematical models of flotation kinetics. Important models are discussed and the structure of their rate constants and parameters is analyzed. Split or enhancement factors are formulated for different kinetic models. The steady state dynamics of the flotation circuits can always be described in terms of these factors. For simulation of circuits, feed is characterized in a formal manner starting from a multivariate distribution of particles in flotation rate, size and mineral content. Synthesis of optimum circuits which simultaneously searches for the best process variables and structural parameters from a generalized master network is described. Trends in the areas of search algorithms, role of middlings and feed identification etc. are indicated.

Jan 1, 1989

By H. Wu, V. Izaxon

Intensive ventilation is required during the excavation of a mine opening and the subsequent exploitation of the mineral resources. The exchange of heat between the ventilation air and the rock mass has a major influence on the thermal regime of a mine, especially in the initial segment of the airway. In frozen ground, heat flow into the rock mass from the ventilation air can result in the eventual thawing of the permafrost, which can result in roof-rock instability. This paper presents a mathematical analysis of the dispersion process of ventilation-induced heat by thermosyphons placed on the surface of the mine. The principal uses of thermosyphons in the Arctic are to reduce the ground temperature to prevent potentially unstable permafrost from thawing and to increase the bearing strength of the material. The mathematical model of the physical problem, generally known as "the Stephan problem," takes into account the varying thermo-physical properties of air and the frozen and thawed rock mass, the thermal properties of the freeing fluid in the thermosyphons and the phase change of water. Finite-difference techniques were employed to determine the temperature isotherms around the thermosyphons. It was found that two rows of thermosyphons on a 10- x 10-m grid provide an acceptable design spacing for reducing the ground temperature around the mine airway.

Jan 1, 1997

By Kenneth L. Rubow, Virgil A. Marple, Ye Tao

Techniques are being developed for measuring the mass concentration of respirable diesel exhaust particles found in underground coal mines. Studies have been conducted over the past five years to investigate size selective sampling techniques to measure the respirable mass concentrations of diesel exhaust and mine dust aerosol particles in underground coal mines. Results from these studies have been used to develop design and performance criteria for a personal diesel exhaust aerosol sampler. Three personal diesel exhaust aerosol samplers have subsequently been designed and evaluated in both laboratory and field settings. These samplers use size selective classifiers for the determination of the respirable mass concentrations of mineral dust and diesel exhaust particles. Their designs are based on the premise that diesel exhaust particles are predominantly less than 0.8µm while mineral dust is greater than 0.8 µm. One design, selected for field evaluation, consists of a 10 mm nylon respirable dust cyclone followed by a 0.8 µm cutpoint impactor and afterfilter. The cyclone removes the large nonrespirable particles while the inertial impactor stage, collects the mineral dust on an impaction plate and allows the diesel particles to penetrate to an afterfilter. The two sample fractions of the respirable particles (<0.8 µm and >0.8 µm) are gravimetrically analyzed to determine the concentrations of the diesel and mineral dust portions in the respirable coal mine aerosol.

Jan 1, 1991

By L. M. English

A basic model was developed to help assess methane control needs for the longwall mining of coal in gassy areas. Rather than depending on reservoir and rock mechanical theories, it uses an empirically determined gas emission rate as an input, and it operates on the assumption that, within a specific region and zone, gas emissions will be relatively equivalent for uniform incremental volumes of gob created by mining. The computer program divides longwall panels into segments, keeps track of the face advance and generates emission rates and volumes for both the entire panel and for individual zones within the panel by summing values for all undermined segments. This model can aid in the determina¬tion of the number, size and location of vertical wells or other methane-control applications that are needed for gob gas control.

Jan 1, 2000

By M. C. Roberts

The consumption of industrial minerals, like most other commodities produced from the earth, depends on the demand for the goods and services that use these materials. Minerals are not generally used directly by final consumers (table salt is a notable exception) but instead are used to either make products that are then purchased by customers, or the minerals are used to make industrial products that eventually contribute towards producing other goods and services. Therefore the demand for industrial minerals in most uses is derived from the ultimate demand for goods and services by consumers. The problem for producers of industrial minerals is that the demand for their mineral product fluctuates greatly in response to the changes in the production of goods and services over the course of the business cycle. In this respect, the producers of industrial mineral are innocent victims, subject to market fluctuations outside of their control. Because the demand for most minerals depends on the demand for the product and because minerals typically make up a minor portion of the costs of producing the product, changes in the price of the mineral often do not influence demand for it to a significant degree in the short run. This is described as a very low price elasticity of demand, as shown by the steep slope of the hypothetical demand curve in Figure 1. This demand curve shows that changing the price of the mineral does not alter the quantity demanded very much, but shifts in the demand curve will be the important determinant of the quantity of the mine.ra1 that is sold. The shifts are caused by the changing demand for the products using the mineral over the course of the business cycle.

Jan 1, 1994