Search Documents

By L. Westerstrom

Supply and Demand After a dismal first half, the industry saw a marked improvement in its markets during the final six months of 1983. Domestic consumption was 17.6% higher in the second half of the year, primarily due to a surge in electric power requirements. The sharp increase in demand for electric power during the third and fourth quarters afforded utilities the opportunity to lower stocks that had accumulated to record levels during 1982. Consumer stocks were reduced from 179 Mt (197 million st) at the end of June to 153 Mt (169 million st) by the end of the year. That is the largest inventory drawdown on record during a six-month period without a major coal strike. Despite the huge depletion in inventories, coal production in the second half of 1983 rose 1.3% above output in the second half of 1982. However, because of the disappointing first half, production in 1983 totaled only 712 Mt (785 million st), 6.4% less than the 760 Mt (838 million st) produced in 1982. Demand The extent to which the economic recovery affected coal markets in 1983 varied: • total domestic coal consumption increased 4.2%; • electric utility coal consumption increased 5.3%; • exports declined by about one-fourth; • coal consumption at coke plants declined 9.5%; and • coal consumption in the other industrial sectors increased 2.9%. Domestic coal consumption totaled 667 Mt (737 million st) it 1983, 27 Mt (30 million st) more than 1982. Electric utility consumption increased from 539 M1 (594 million st) in 1982 to 567 M1 (625 million st) in 1983. Coal consumption at coke plants declined from 37 Mt (41 million st) to 34 M1 (37 million st). Residential and commercial use increased 181 kt (200,000 st) - from 7.4 to 7.6 Mt (8.2 to 8.4 million st). Electric Utilities: Electric power generation increased 3.1% in 1983. Demand for electric power increased in all major consumer categories. Residential and commercial use rose 2.7% and 3.3%, respectively. The most striking increase, however, and indicative of the economy's strong upturn, was the increase in industrial electric power use. Industrial power requirements, which declined 9.8% in 1982, rose 4.1% in 1983. The electric utility sector continued to expand its use of coal last year while lowering its requirements of oil and natural gas. In 1983, electric generation from coal increased 5.7%, while genera-

Jan 5, 1984

By Nathaniel Arbiter

Flotation’s earliest patent was issued in 1860. However, the process was first applied commercially in Australia until 1904, and in Montana in 1911. Major advances followed both in reagent treatment and in cell design, with resulting process improvements. Mechanical cells have seen the widest use and with the major increases in plant capacities (Fig. 1) their volumes have also increased (Fig. 2). In 1991, the principal use for the process was to produce copper concentrates for smelting. It was applied to 243 Mt (268 million st) of copper ore. The total of all ores floated that year was 426 Mt (470million st). In 1997, US mines produced 257 Mt (284 million st) of copper ores for flotation, yielding1.75 Mt (1.94 million st) of copper.

Jan 1, 2000

By J. Jeffrey Wagner, Michael J. Bailey, Peter M. Douglass

The Chambers Creek Interceptor Sewer Tunnel project consisted of 2-1/2 miles (4 kilometres) of nominal 9-foot (2.7-metre) O.D. tunnel driven through predominantly glacially overridden soils. Mole-Collucio Construction Company initially elected to drive the entire tunnel with a Lovat TBM. However, this machine could not control the fast raveling ground conditions which developed when the TBM encountered sands overlying very dense, hard glacial till or boulders. As a result, a shield and digger machine was brought in for a 1700-foot (518-metre) long segment. Pumped wells spaced roughly 50 to 125 feet (15 to 38 metres) apart were utilized to dewater about two-thirds of the alignment during construction. Initial support consisted of steel ribs and wood lagging, with a final lining comprised of pre-cast concrete pipe segments grouted in place.

Jan 1, 1985

The Barrick Zaldivar mine is an openpit, heap-leach copper mine in Region II of northern Chile at an elevation of 3,300 m (10,826 ft), approximately 1,400 km (870 miles) north of Santiago and 175 km (109 miles) southeast of the port city of Antofagasta. In 2006, Zaldívar produced 307 million lbs of copper, with reserves estimated at 5.7 billion lbs. The mine uses conventional methods of openpit mining: Pure cathode copper is produced by three stages of crushing and stacking the ore, followed by heap leaching and bacterial activity to extract copper from the ore into solution. A solvent extraction and electrowinning process then removes the copper from solution and produces the cathode copper. A flotation plant also recovers copper contained in the fine fraction of the crushed ore. In 2006, an existing A-frame structure that covered copper ore from the mine?s secondary crushing operation was damaged beyond repair. The material delivery configuration of this original structure had the conveyor carrying incoming ore directly over the low roof to drop ore into the building at its peak, and ore trickling from the sides of the conveyor had accumulated on the roof, overloading it. A better solution had to be found, and fast: First, the Chilean Commission does not permit uncovered piles of this type since the extremely fine material leads to serious pollution problems. Second, Barrick Zaldivar is very concerned about worker safety, and the amount of dust created by the uncovered pile was not acceptable. Finally, some amount of copper was lost in the dust generated by the winds of the Andes. The major issues faced by Barrick Zaldivar in designing a new structure included:

Jan 1, 2009

By Günter Huber, Bruno Mattle, Helmut Westermayr, Daniel Spöndlin, Max John, Nejad Ayaydin

PROJECT DESCRIPTION Alignment The Strenger Tunnel forms part of the S16 four-lane expressway between Landeckand Bludenz. The construction of this important East-West connection started in 1973with the Arlberg Road Tunnel as its key constituent. Beginning in 1992, solutions for the section between Pians and Flirsch were investigated. Efforts to conserve nature and to avoid potential avalanche and landslide areas led to a solution detouring the villages in the Stanz valley. The starting points were predetermind by the intersections at Pians in the East and at Flirsch in the West. As a result of the expected traffic load and the comparatively high gradient of 2.9%, both one-way, two-lane tubes were constructed at once. The north tube is 5.851 m long, the south tube 5.775 m, see Figure 1. Layout of Tunnel Cross-Section The tunnel cross-section was determined by 2 × 3.75 m wide, 4.70 m high roadways, two sidewalks and sufficient space for two fans above the clearance

Jan 1, 2005

By Raymond W. Henn

The 31th annual short course ?Grouting Fundamentals and Current Practice? was held at the Colorado School of Mines, in Golden, CO June 7-11, 2010. The field demonstration portion of the course was conducted June 10 at wlh Construction Co.?s yard in Denver, CO. The full-scale field demonstration presents many types of drilling and grouting equipment in operation as well as numerous grouting methods performed under various field conditions.

Jan 1, 2010

By Ravi Ray, Kostas Kaklis, Zach Agioutantis

"Modern underground mining is becoming more complex and geotechnically challenging. The engineer uses numerical, analytical, and data-driven methods (empirical and/or experimental) or their combination to overcome these challenges. Each method has its advantages and disadvantages. Nevertheless, given the amount of innovation and experience involved in developing each of these techniques, it will be prudent to use all their benefits rather than favoring one technique over the other. Pillars are the most important support element in an underground mine. A holistic geo-mechanical solution needs to be determined to design mine pillars using a proper sequence and exact mix of the three methods. A combination of these methods, in sync, can encompass the several advantages of the three methods while eliminating their disadvantages. This paper presents a conceptual three-tier solution to the pillar design problem, to improve its design pedigree, using a proper combination of numerical, analytical, and data-driven methods. At the focus of this proposed method lies the Ground Reaction Curve (GRC) concept.INTRODUCTIONAlthough the stability analysis of underground excavations is a challenging problem, its understanding has improved tremendously over recent years through the use of improved tools and techniques. The trial and error method was replaced with more scientific methods like the empirical and analytical methods that are still in use today. Empirical methods were developed based on large data sets obtained from experiments and observations (e.g., coal pillar strength equations). Analytical methods were developed based on mechanical understanding of stability (e.g., safety factor for vertical pillar loading, Convergence Confinement Method). Improvement in computing power and numerical techniques led to the development of several numerical methods (e.g., finite difference, finite element) suitable for geo-mechanical analysis.Each of these methods have certain advantages and limitations. Nevertheless, the user is often puzzled over the proper method selection and over the proper sequence of using them. This exercise becomes more challenging when different methods are combined, where, for example, one has to estimate the pillar strength based on empirical equations (e.g., Mark-Bieniawski coal pillar strength equation), determine the factor of safety based on an analytical approach (e.g., tributary area load divided by pillar strength), and analyze pillar-strata interactions using numerical analysis (see Esterhuizen, Mark, and Murphy, 2010b).Challenges increase when current pillar design methods are designed as passive structures to balance the fixed dead weight of the overburden. This classic suspension design approach does not recognize the self-stabilizing capacity of the overburden (Frith and Reed, 2018). A practical solution to address these issues is the use of numerical analysis. However, one should always keep in mind that the numerical modelling approach may have certain practical limitations."

Jan 1, 2019

Filtration systems with disposable filter elements (DFEs) are used in the underground coal mining industry to control particulate matter emissions from diesel-powered permissible and nonpermissible coal mining equipment. This study was conducted in underground mine conditions to evaluate three types of high-temperature DFEs used in those filtration systems. The DFEs were evaluated for their effects on the concentrations and size distributions of diesel aerosols and concentrations of nitric oxide (NO) and nitrogen dioxide (NO2). Those effects were compared with the effects of a standard muffler. The experimental work was conducted directly in an underground environment using a unique diesel laboratory developed in an underground experimental mine. After an initial DFE degreening period, the filtration system with all three DFEs was found to be very effective at reducing total mass concentrations of aerosols in the mine air. The effectiveness of DFEs in filtering aerosol mass was found to be a function of the engine operating conditions. The efficiency of the new DFEs significantly increased with accumulation of operating time and buildup of diesel particulate matter in the porous structure of the filter elements. A single laundering process did not exhibit substantial effects on performance of the DFE elements. The effectiveness of DFEs in removing aerosols by number was strongly influenced by engine operating mode. The concentrations of nucleation mode aerosols in the mine air were found to be substantially higher for both DPFs and DFEs when the engine was operated at high-load modes than at low-load modes. Initial heating of certain DFEs resulted in visible white smoke and substantially elevated aerosol number concentrations. The effects of the DFEs on total nitrogen oxides (NOX) concentrations were found to be minor. The NO2 fraction was found to be generally lower for the DFEs than for the muffler. The engine-out NO2 fraction of the total NOX was found to be substantially higher for low-load modes than for high-load modes.

Jan 1, 2011

By David Smith

Construction of a new transportation link frequently requires crossing under an existing highway or railroad. Although traffic diversions may permit a cut and cover structure to be built, ‘zero impact’ tunnel solutions are becoming increasingly popular. The vertical clearance between the new tunnel structure and the existing highway or tracks may be very low; sometimes less than two meters. This leaves little room for error since any ground loss can rapidly translate into surface settlement. Problems can be avoided by maintaining the stability of the tunnel face and by minimizing ground movement around the tunnel lining. This paper examines construction methods that have been used to construct short tunnels with shallow cover, and highlights factors to be considered for future projects.

Jan 1, 2005

By Leslie F. Ruppert

The US Geological Survey (USGS) is currently conducting a coal resource assessment of the coalbeds and zones that are projected to provide the bulk of the nation’s resources for the next few decades. The Pittsburgh and Upper Freeport coals are the first two beds in the northern and central Appalachian basin region to undergo fully digital coal assessments. The bed-specific assessments are being carried out in partnership with the state geologic surveys of West Virginia, Ohio, Pennsylvania and Maryland. Comprehensive stratigraphic and geochemical databases have been developed for both of the beds. The extent of the bed with mined areas, structure contour, isopach, and overburden thickness maps for the Pittsburgh coal bed have been released as USGS open-file reports.

Jan 1, 1999

NASA has received direction for lunar habitation beginning in 2024. Prior to then, it will be necessary to learn about how lunar soil can be used to promote civilization on the moon. Questions must be answered: ?Will it support plant life?,? ?Can it be used as a construction material?,? ?What is needed to maximize health and safety?,? and ?Will it affect equipment, tools, machinery, and clothes?? The only samples available for study came from the Apollo Missions. Because the expense of bringing more material back to Earth is prohibitive, there is not enough available to perform studies to answer the above questions. Hence, there is a great need for its synthesis. Most efforts to date have concentrated on making ?simulant? from single natural resources of volcanic rock. However, another possibility is to use resources here on Earth to extract the minerals of interest into concentrates or so-called ?separates? using traditional mineral processing techniques, and then mix the separates in appropriate ratios to simulate the lunar soil. In this paper, results from a study in which dry Road Norite outcrop and wet mill tailings from the Stillwater Mining Company?s Concentrator located near Nye, MT were examined. Of course, the in-side challenge is to make ?separates? from gangue minerals.

Jan 1, 2012

Despite the current economic downturn that is now decimating iron ore production, Minnesota?s mining operators remain optimistic about the long-term prospects for the industry. Reflecting this optimism, the development of several new mining projects continues in the state. The future of mining in Minnesota was the featured topic at the combined 82nd Annual Minnesota Section of SME Meeting and 70th Annual University of Minnesota Mining Symposium. More than 500 mining industry professionals, including engineers, executives, mining managers and equipment suppliers from the around the world, attended the meeting, which was held April 14 and 15, 2009, in Duluth, MN. The combined meeting featured a keynote session with three distinguished speakers plus a panel discussion by representatives from several of Minnesota?s taconite producers. The keynote speakers were Curtis Clark, president and chief operating officer, Behr Dolbear, who gave a presentation on the ?State of the Mining Industry.? Phil Newman, chief operating officer, CRU Strategies, spoke about challenges facing the mining industry and James A. Skurla, acting director, Bureau of Business and Economic Research, Labovitz School of Business and Economics, University of Minnesota Duluth, discussed the importance of mining to northeastern Minnesota?s economy. The taconite producers panel discussion included Jonathan Holmes, vice president and operations manager, ArcelorMittal; Ed Latendresse, vice president and general manger, Hibbing Taconite; John Tuomi, vice president operations services, United Taconite and Mike Mliner, vice president and general manager, Northshore Mining. The mangers provided updates on their respective operation The meeting included concurrent technical papers sessions on mining, processing, environmental and nonferrous mining. The sessions included technical papers that provided information on the status of a number of new mining projects in the state. The conference also offered a SME short course titled ?The basics of iron mining.? A tradeshow that featured about 100 companies and organizations offering products and services to Minnesota?s mining industry ran in conjunction to the conference. It was estimated that more than 900 people, including conference registrants and special invited guests of the vendors, attended the tradeshow opening reception. This was the largest trade show in many years. The Minnesota Section of SME also held its annual business meeting during the conference.

Jan 1, 2009

By S. R. S. Sastri

By using the data of E.A. Hersam and F.C. Bond's equation for energy consumption in comminution, a method was developed to analyze the performance of industrial jaw crushers. The study showed that industrial jaw crushers are generally operated below capacity. The study also showed that industrial jaw crushers generally have sufficient installed power to operate at, full capacity. The method presented can be used to estimate the capacities and power requirements of jaw crushers.

Jan 1, 1995

By Lane White

Refractory gold ores are those from which a significant percentage of the gold cannot be recovered by conventional cyanidation. Historically, roasting has been the primary method for rendering such ores amenable to gold extraction; however, roasting creates environmental problems that are not acceptable in many locations. During the 1980s, consistently strong gold prices drew increasing attention to refractory gold ores, and new processing schemes were commercialized, most prominently aqueous pressure oxidation and more recently bacterial oxidation. Since 1985, pressure oxidation has been incorporated into four plants processing refractory gold ores. A fifth plant is scheduled for start-up in early 1990, and three additional plants are scheduled for production before late 1992. A technical session on treatment of refractory ores was included in the program of `World Gold '89, a Gold Forum on Technology and Practices' held by SME and the AusIMM in Reno, NV, Nov. 5-8, 1989. This article summarizes material from five of the papers presented during the refractory gold session and published in the proceedings of `World Gold '89,' edited by Roshan Bhappu and Rod Harden. The complete proceedings are available from SME Publications Sales, P.O. Box 625002, Littleton, CO 80162-5002 $53.50 for members, $38.50 for student members, and $73.50 list price.

Jan 1, 1990

By Shimi Tzobery, Jay Davenport, Raymond Henn, Sam Bandimere

Over the past several decades, the use of cement-based grouts using ultra fine cement as a replacement for portland cement has begun to gain acceptance as an alternative to chemical solution grouts used in permeation grouting. The amount of information currently available on grouts made with ultrafine cement is limited. The authors used a previously developed field testing program to perform additional tests to evaluate the permeation performance of portland and ultrafine cement-based grouts. For the first time, the 2003 testing program included an attempt to determine the 28 day compressive strength of the sand permeated by the grout.

Jan 1, 2005

By Michael R. Walsh, John H. Wright, Eivind B. Jensen

A tunnel boring machine (TBM) was designed and built at the Cold Regions Research and Engineering Laboratory in 1992 for use in Antarctica. The TBM system was tested at the South Pole where a 120-m long tunnel was bored to prove the concept. Modifications were made to the system resulting from this work. In 1999,boring of a 600-mutilidor began as part of the new South Pole Station. Tunneler hydraulics reliability problems prevented the completion of the tunnel before the end of the short construction season. This paper discusses the design and operation of the TBM, proposed solutions to the problems encountered, and current operations of the system.

Jan 1, 2001

By Greg Sheppard, Eduardo Nebot

Australian researchers have developed new technologies aimed at improving safety and productivity at openpit mines. A data acquisition and feedback system for electric rope shovels has been shown to substantially reduce cycle times and decrease excessive machine duty caused by stalls. This data acquisition system was developed by the Cooperative Research Center for Mining Technology and Equipment (CMTE). It has been tested on a P&H 4100A shovel at Coal & Allied’s Hunter Valley operations and a P&H 4100XPB at BHP Billiton Mitsubishi Alliance’s Goonyella Riverside Mine in Central Queensland. In addition, CMTE member P&H Mine Pro Services has used the technology to acquire field data from a P&H 4100XPBrope shovel at RAG’s Belle Ayr Mine in Wyoming’s Powder River Basin.

Jan 1, 2002

By J. H. Daniel, S. Krzemien

Partners In Economic Reform, Inc., established a Polish-American Mine Center in Katowice, Poland, in 1996 to improve working conditions in the minerals industry. The program was based on the experience of mining companies, government, and labor in the United States, and was executed by a Coordinating Committee headed by the Center Director and Polish leaders from industry, State, labor, and academia. The cooperation among all parties has enabled safety and health issues to become part of industry restructuring with impressive initial reductions in coal mine fatalities. Existing work practices and attitudes of labor and management were assessed in coal mines throughout the country. Promotion, Rules, and Job and Task Analysis were identified as the areas requiring the most improvement, and are part of a post-graduate Safety Management program. Demonstration projects included measuring dust levels, using safety glasses, and promoting hazard awareness. Improved labor-management relations increased cooperation allowing for effective transfer of technology. Results can also be applied to improve the working environment of the manufacturing sector also undergoing restructuring.

Jan 1, 2001

By A. T. Iannacchione

From 1990 to 1996, 16 states reported 92 injuries from falls of roof, rib or face in the more than 90 underground stone mines in the United States (Fig.1). Missouri, Pennsylvania and Kentucky accounted for 48% of the total number of injuries (Fig. 2). Of this total, 11 miners were killed. Of the 11 fatalities, 10, or 91%, were associated with unrecognized loose or failed rock within the roof beam. Additionally, unrecognized roof beam failures resulted in a majority of the falls of ground injuries occurring in underground US stone mines from1990 to 1996. This number is not large in magnitude. But a workforce of fewer than 2,000 miners makes for a high fatal-accident rate. The severity of the typical fall-of-ground injury is, in general, very high. About three-fifths of all roof, face and rib fall injuries were designated by the US Mine Safety and Health Administration (MSHA) as some kind of lost time accident. MSHA assigns each accident a severity value from one to six. A one represents a fatality, a two, a permanent disability and three, a lost time accident (Fig. 3).

Jan 1, 2000

By Marco Sonnenschein

As time is costly, engineering companies have developed methods, procedures and mechanical equipment to tunnel faster. But the best excavation method will not be able to cope with the time pressure if there is not a reliable backup system. Therefore, the application of belt conveyors for tunnel boring machine (TBM) drives as well as for drill-and-blast driven tunnels assure a quick and smooth removal of excavated soil in order to enhance the efficiency of the tunneling equipment. During the last 10 years, belt conveyor systems have achieved ?state-of-the-art? levels and have become the first choice for muck removal systems in both TBM and drill-and-blast driven tunnels. Because time has become such a key criterion in tunneling projects, it is essential that all equipment is operated so as to derive optimum efficiency and minimize costs. Efficiency also means to think about new tasks for existing technologies.

Jan 1, 2012