Search Documents

By Stephen H. E. Phillips, Michael J. Beus

A pneumatic impact breaker is used to fragment the rock at the shaft bottom, replacing the drill and blast cycle. A backhoe-type mucker removes the broken rock. The operators are in protective cabs below the bottom work deck in the shaft. Preliminary testing has been accomplished at underground and surface test sites in Arizona. Seven, approximately 6.4 m deep by 7.3 m-diameter (21 ft by 24 ft) test holes, (a total of 45 m (148 ft)), were recently excavated in various rock types, including jointed and massive quartz monzonite and rhyolite. An average advance rate of .4 m/hr (1.24 ft/hr) has been achieved. This includes breaking and mucking the rock. Further data is being sought from an in-shaft demonstration.

Jan 1, 1981

By R. L. Schmidt, Williamson. T. N.

INTRODUCTION This paper describes one of several research projects funded by the Advanced Research Projects Agency to extend the technology of rapid underground excavation. This study and field research effort are to investigate alternative means to determine rock and geological conditions in advance of a tunnel boring machine (TBM). Approximately 1 year of a planned 3-year program has resulted in the definition of three candidate drill systems. Hardware has been assembled to field test these candidates and testing has begun. The 3-year objective is to develop a single optimum prototype drill and test it in an active TBM operation. ACKNOWLEDGMENT This research was supported by the Advanced Research Projects Agency (ARPA) of the Department of Defense and was monitored by the Bureau of Mines under Contract No. H0210037. The authors and sponsoring agencies are indebted to the quarry operators in California, Virginia, and West Virginia who offered assistance including access to their properties.

Jan 1, 1997

By Jouko Suominen

The basic development of various mining equipment has been strongly influenced by two objectives; improving economic results and safety aspects. Both of these factors contribute to increased requirements of mechanization and automation in different parts of mining processes. When we are limiting the discussion the crushing circuits, automation has two dimensions, one being the component automation, or intelligence, the other being automation of complete processes. Both of these subjects are closely tied up, the former being a condition for the latter. The key technologies of crushing automation are transducers, programmable logics and computer software. Also equipment technology continually faces new challenges, which result even in totally new product families. One example of this kind of development area the track-mounted, integrated crushing systems, where design criteria have been simple control, unmanned operation, and flexibility in changing requirements. This crushing system, or philosophy, offers excellent possibilities for new concepts in various underground and open pit applications, connected with automatic process control. Following presentation is a summary of aspects, of haw a crusher manufac¬turer sees the development of automa¬tion as an integral part of equipment technology and development.

Jan 1, 1989

In the mining industry and in new and expanding fields, such as electronics, nucleonics, and astronautics, a new type of manager has evolved. The name most generally used is project manager. His business is to create a product and the principal means through which he accomplishes this is project management. In this chapter, new information is the product of the project manager; as such the products, for which the computer methods described throughout this volume are designed, fall in the domain of project management. It has been the author's experience that project management is the management tool to effectively direct the information technology function within an organization. The purpose of this chapter is to describe project management and to identify and present a solution to the problems associated with project management in the development and application of computer methods in a minerals environment. Specifically, the problems to be addressed will center around: (1) recognition of the need for project management in terms of business-environmental factors and product characteristics, (2) formulation of a method of operation in terms of organization and implementation, and (3) application of project management to the minerals industry.

Jan 1, 1979

By R. E. Weeks, D. J. Millenacker

Utilization of true in situ technologies for mining copper in Arizona will involve a complex environmental permitting process. This process is a key factor in determining the feasibility, costs, and implementing time- frames required for development of this innovative mining method. The regulatory structure in Arizona is presently changing due to enactment of the Environmental Quality Act (EQA) of 1986 and development of new aquifer protection rules and regulations. The US Bureau of Mines has reviewed the comprehensive hydrogeologic characterization, ground water monitoring, mechanical integrity testing, well construction, contingency planning, and other regulatory elements that will serve as mechanisms to assure protection of ground water resources. The purpose of this paper is to inform the domestic copper industry of the significance of the new Arizona regulatory structure and its implications for prospective in situ operators.

Jan 1, 1987

By V. F. Hollister

Copper and gold were discovered in the Copper Canyon area of the Battle Mountain district of Lander County, Nevada, in August of 1866. By 1876 a gravity plant was con¬centrating oxidized Copper Canyon copper-gold ores. The history of mining in the district to 1967 has been summarized by John E. Frost (in press) as a case history of the discovery of the Battle Mountain porphyry copper deposits. His summary is not repeated here; rather, the present case history covers exploration since 1967, primarily for gold ores. Subsequent to the construction by Duval of facilities to mine the porphyry copper deposits in 1967, Duval established a geologic staff at the mine to continue district exploration. The staff was guided by David W. Blake, who acted as chief geologist for Duval's exploration in this part of Nevada. Blake's activities led to the publication of numerous technical articles, including his contribution to the US Geological Survey Professional Paper 798-B. A part of that volume is attached as a reprint (pages 23 through 66) as an explanation of the geological setting of mineralization in the district. The work by Blake and his staff recognized metal zonation in the skarn environment at Copper Canyon, and their studies were incorporated in the development of the Tomboy-Minnie gold deposits that are peripheral to the porphyry. Exploration continued beyond the immediate vicinity of the porphyry and the Fortitude ore zones were discovered. These skarn deposits are described in the attached article by Wotruba, Benson, and Schmidt, published in the July 1986, MINING ENGINEERING. The continued exploration successes at Battle Mountain reflect on the well organized and effective exploration team developed at the mine. The team has provided successive discoveries in a district known mostly for ore bodies that are exhausted in a few years' time.

Jan 1, 1990

By Edward C. Dowling

The advance of science and technology influences the modern economy in countless ways. Older industries must adapt to changes in the marketplace, while new industries are born by applying new technology to meet consumer needs. In light of declining head grades and increased unit costs in the US minerals industry, new technological developments in the production environment are paramount to maintaining a competitive footing in the international marketplace. Micro-engineering research provides the transition between the knowledge base and the application of new technology on the production level. Economic considerations The primary goal of technical development in the production environment is to reduce unit operating costs. Simply stated, this is accomplished by improving operating efficiencies and productivities on the production level. The goal of micro-engineering research in the production environment is to evaluate promising technologies and develop the criteria necessary to apply them in operations. As such, this process is the first step toward innovation and discovery. Generally, the micro-engineering research is followed by macro-engineering development. In the production environment, there are generally more development projects than can be accomplished in a timely manner. Usually, this is the result of financial and human resource limitations. Consequently, it is necessary to prioritize the work such that the most beneficial projects are accomplished first. By performing a discounted cash flow analysis and using benefit-cost ratios (for non-mutually exclusive alter¬natives) or net present value criteria (for mutually exclusive alternatives), the projects can be rated from best to worst. In this way, the financial and human resources can be best allocated to first complete those projects giving the highest returns before moving on to other activities. Moreover, this information is a prerequisite for management to justify additional financial or human resources.

Jan 1, 1992

By Harald F. Solberg

A preliminary study of the performance of a 4-inch Krebs cyclone at near rope conditions and different feed slurry temperatures was completed. Results suggest that temperature influences the x50c size which, in turn, did not depend upon spigot diameter. The bypass correction to a reduced efficiency equation incorporating the concept of a critical size xo was a function of fractional water recovery to underflow and may depend on feed size and feed percent solids. Further experimentation is required to develop an accurate model at near rope conditions.

Jan 1, 1981

By Bart Hogeweg

The development of deep sea mineral deposits creates a new horizon for the mining industry. In a field where mining technology meets deep-water offshore engineering, new challenges are faced to come to the successful exploitation of these deposits. With the absence of proven technology for the mining of these minerals, a ?technological green field? is entered. IHC Merwede (IHC), a global market leader in the dredging and wet mining industry, is on the frontline of these developments. MTI Holland, IHC Merwede?s research and development company, has undertaken a number research efforts focused on the successful development of technology for the mining of deep sea minerals. This paper highlights a number of these efforts and illustrates IHC?s continued dedication for the research and development of technology to enable the commercial mining of deep sea minerals.

Jan 1, 2008

By R. Gerling

A computer program has been developed for finding a near-optimum schedule of the mining sequence for flat lying, tabular orebodies. The deposit is divided in blocks with equal areas and definite grades, thicknesses and ore contents. Mining is done by room and pillar method and trackless haulage to surface. Access from surface is by adits or ramps with additional vent raises. In total eight different general concepts for access and development can be realized. The optimum mining sequence is found by a heuristic method. Criterion is the maximization of the net present value over the lifetime of the mine. Specific stoping costs per t of ore are taken for con¬stant, whereas development and haulage costs for individual blocks and also sequences will be different. Correct ventilation and a technically sensible sequence are guaranteed. Beginning with a single block, neighbouring blocks are tested and an optimum stoping sequence is generated. The net present value of the total mining operation for the planning period is calculated, taking into account ore, which is mined during development. The program can also be used to investigate given mining sequences.

Jan 1, 1986

By P. Venkatasubramanian

The selection of a mining method for a mineral deposit is a complex decision problem. Human judgment, based on experience with mineral deposits and geologic conditions, remains the single most important input of the decision-making technique. If the use of artificial intelligence, in particular the developments in expert systems, is taken to its logical conclusion, the experience of the domain experts could be incorporated into a decision-support expert system. A knowledge-based decision support system for mining method selection for ore deposits has been designed whereby the domain knowledge is represented as production rules and organized in a semantic tree representation. This model is written in the PROLOG language. While the verification difficulties of expert systems models are recognized, an example of the model's decision on the mining method for a given ore body is presented and shown to be consistent with the decision made by human experts. In addition, plans, for further verification of the model are delineated.

Jan 1, 1992

By Jack G. Pippenger

This report focuses on the procedures required to review, prepare specifications, bid, and purchase a fully integrated computer system for utilization by engineering personnel in all phases of mine engineering. The presentation is based on the experiences encountered in 1984 in procuring an engineering computer system at The North American Coal Corporation's Western Divi- sion. A two-phase report detailing the purchasing process and subsequent utilization of the engineering computer system will be given. Special detail is also provided on the final system hardware and software setup.

Jan 1, 1989

By W. A. Rickelton, A. J. Robertson

The ability of triisobutylphosphine sulfides to selectively recover silver from acidic sulfate solutions containing zinc and copper is described. Selectivity is explained in terms of the concept of hard and son Lewis acids and bases. Silver is stripped from the solvent using a novel strip feed (thiosulfate salt), and the recovery of metallic silver from the strip liquor by electrolysis or cementation is suggested. The high selectivity of extraction for silver and the utility of the stripping reagent are demonstrated in continuous, countercurrent, mini-plant tests. Important reagent properties, such as hydrolytic stability and low aqueous solubility, are discussed.

Jan 1, 1988

By R. L. Urie, L. Burdzinski

Non-operational mine facilities are subject to placement on the EPA's National Priority List (Superfund). Once a mine site is undergoing investigation and/or remediation, MSHA regulations for health and safety may no longer be applicable. This paper addresses the changes in the applicable and relevant standards that apply to health and safety and public health related to site contaminants. The implementation of health and safety plans, and the development of public health risk assessments are described. Examples are presented from Superfund activities at the Eagle Mine, near Minturn, Colorado; the Anaconda Smelter near Mill Creek, Montana; California Gulch near Leadville, Colorado; and Bunker Hill, Idaho.

Jan 1, 1991

By R. D. Willette

The Hector Mine deposit in the California Mojave Desert has a magnesium-rich clay that formed when lithium and fluorine were introduced into isolated fine lacustrine volcanic sediment during the Pliocene. The intensely deformed deposit has been supplying the highest grade thixotropic clay to the coatings industry for over half a century. A thixotropic clay displays the property of changing from a gel to a sol when shaken, and increases in strength upon standing.

Jan 1, 1995

INTRODUCTION Automatic controls are devices that assist operators by performing routine tasks faster and better than they could alone. Great strides have keen taken in the development of new processes and bigger machines to improve productivity, but these developments created the need for increased protection of machinery and labor. The new production-line techniques, or continuous processes developed, resulted in routine and, frequently, demoralizing jobs. The human race is not constituted mentally to perform routine operations. Devices were needed also to gather information automatically and perform routine functions. High-capacity plants incorporating large equipment

Jan 1, 1985

By Albert E. Ketler

The techniques for fire monitoring of conveyor belts in underground coal mines have been revolutionized by the advent of sensitive carbon monoxide sensors and computer monitoring systems. These new systems are rapidly replacing the previous thermal (fixed-point temperature) sensors that have been shown to be considerably less sensitive for early fire warning. CO is generally an excellent indicator of spontaneous combustion. However, the most recent non-flammable conveyor belt materials have been shown to "burn" with dense smoke, but without sufficiently high temperatures to produce much carbon monoxide. To cover this fire detection void, a smoke detector was developed to augment CO sensing for these new conveyor materials. However, computer monitoring provides the flexibility for handling this and other additional instrumentation as fire monitoring techniques evolve. CO, smoke and temperature sensing may eventually be advocated for complete fire monitoring.

Jan 1, 1987

By S. L. Bolivar

The Prairie Creek intrusion, near Murfreesboro, AR, is the site of the most famous diamond mine in North America. Three major rock types are associated with the intrusion-a hypabyssal peridotite, a volcanic breccia in which the majority of diamonds occur, and tuft. Previous studies, including geological, geophysical, petrological, and whole-rock and mineral chemistry are reviewed. The recent suggestion, by other workers, that this intrusion may be more correctly called a lamproite is examined. This has serious implications for diamond exploration in Arkansas and elsewhere in the US.

Jan 1, 1987

By Roger Beckie, Leslie Smith, Craig Nichol

To study the hydrogeological processes that control the movement of water through unsaturated waste rock, an intermediate-scale (8m x 8m x 5m) waste rock pile has been constructed and instrumented. The constructed pile is monitored for moisture content, matric suction, temperature, matrix water chemistry, gas chemistry, gas pressure, rainfall, evaporation, discharge volume and discharge chemistry. The pile is built upon a grid of 16 contiguous lysimeters. The experiment is designed to investigate the mechanisms that create rapid water flow through a pile and its exchange with slower-moving matrix water.

Jan 1, 2000

By R. L. Grayson, Y. J. Wang

An application of material requirements planning (MRP) to coal mine inventory control is presented. MRP is an efficient material control system that integrates the production planning and inventory management functions. Net material requirements are determined from the production forecast utilizing bill of material files, the inventory status file, and the purchase order status file. Net requirements are computed for each period in a specified planning horizon, and purchase orders, offset by lead time, are initiated routinely to ensure timely receipt of materials. The MRP system is especially useful in production-inventory systems in which con¬sumption of materials is directly production dependent.

Jan 1, 1987