Search Documents

By Larry F. Brown

Mining has been the mainstay of the Woods Creek Valley for more than a century. The head of the valley is at the Continental Divide, about 50 miles west of Denver, Colorado. First, it was the quest for gold and silver that drew people to the valley. Then, when molybdenum was classified as a strategic metal by the U. S. Government during World War I, it was the valley's molybdenum mineralization which attracted the most attention. Molybdenum is used primarily as an alloying material in superior grades of steel. Circumstances responsible for providing the label "Urad" are unknown, but Urad is variously reported to be an acronym for "Uranium Research and Development" or "Uranium Research of America Division". The search for uranium was fruitless as no ore grade uranium exists in this area. The moly orebody was first developed and mined by the Primos Exploration Company from 1914 to 1919. During World War II, the mine was purchased by the government and turned over to the Molybdenum Corporation of America to operate. In 1963 AMAX Inc. purchased the property for $2 million. After spending nearly $30 million for exploration and development, AMAX put the mine into production again in 1967.

Jan 1, 1984

By Owens S. Roberts

The drive selected for any piece of machinery must adequately satisfy the application requirements both during the starting interval and at running conditions, All loading possibilities of the drive must be known and allowances made for any adverse limiting conditions such as extreme cold, or perhaps an intermittent excessive loading situation etc. In general, the drive must be selected to provide the required operating characteristics with maximum reliability and at minimum cost. Simplicity of overall design is always an advantage and care must be exercised to insure that systems incorporating unnecessary complicated parts are not indiscriminantly provided. Important non-technical considerations such as equipment avail-ability (on an overseas project) as well as standardization details also play a role in the drive selection process. Additionally, an assessment of the potential capabilities of the personnel that will have to maintain the equipment can have some influence on the final choice. Several types of prime movers are available but this article will restrict itself to the use of induction motors operating from an available alternating current power source. Many drive arrangements are possible, the most common being the direct coupled single motor arrangement. It is sometimes desirable to use more than one motor per machine, but these designs are usually more

Jan 1, 1971

By James R. Evans

Forecasting demand is an art as well as a science, and much personal judgment is required. National forecasts made for sand and gravel, crushed stone, and/or aggregate may be misleading or unhelpful locally. This is because of significant variation in demand within different geographic and/or political areas in the United States, and/or the use of an inadequate data base and forecasting methodology. The best forecasts may be made for local or regional market areas, irrespective of geographic or political boundaries, provided a proper data base is available. The Bureau of Mines compiles detailed statistics on commodities sold or used in the construction industries and, therefore, is in an advantageous position to make national aggregate demand forecasts.

Jan 1, 1978

By Jin Zhao, Weijie Wei, Jinwang Zhang, Xiaohang Wan, Shengli Yang

Reasonable mining-retention ratio (ratio of room width to pillar width) is vital to recovery rate and stope stability in underground mining of solid potassium salt deposits. Based on the engineering background of a solid underground potassium salt mine in Khammouan Province, characteristics of the plastic zone of the pillar, and the variation of recovery rate and stope stability under different mining-retention ratio conditions are discussed. The results show that compared with current room width (8 m) and pillar width (10 m), the optimization method of improvement of stope stability. The research results are helpful to recover as much solid potash resources as possible under the premise of ensuring the stability of stope.

Jun 25, 2024

By Steve Kral

The third edition of the Underground Construction Association of SME?s (UCA) Cut-ting Edge series of conferences focused on a challenge every underground construction and tunneling project faces: controlling ground water. The conference, held in New York City in November, is a partnership between the UCA and The North American Tunneling Journal. It featured more than 20 technical presentations by professionals from around the world. Each described specific challenges unique to their projects and the solutions employed. More than 175 professionals attended the two-day conference that included an exhibition featuring 17 companies. In addition to the technical program, the Cutting Edge conference featured a site visit to the $10.4 billion East Side Access Project. Sponsors of the meeting included Soil Freeze, Traylor Bros., Kiewit, Skanska, Moretrench, Aecom and The Robbins Co.

The conveyor housing's corroded, exposed metal- deck was cleaned and cocooned to prevent renewed corrosion, at less than the cost of replacing the structure. And the process did not require operations to shut down. That was the result for Akzo Salt at its mine under Lake Erie's Whiskey Island, just off Cleveland, OH'S north coast. The exposed metal deck was on the underside of a covered, outdoor conveyor used to load mined road salt into boats.

Jan 1, 1997

Drainage and erosion control often become problems at mine reclamation projects. An example of this was an abandoned surface uranium mine on the south Texas plains. Engineers with the Texas Railroad Commission solved these and other problems with a three-dimensional geomatrix erosion-control matting at the 69-hm2 (170-acre) site, about 70 km (45 miles) southeast of San Antonio. Enkamat, manufactured by Akzo Nobel Geosynthetics, was installed to reinforce the grass waterways that handle runoff from the reclaimed mine. Reclamation was completed in the spring of 1992. Bill Walker is regional manager for Erosion Control Systems. He worked with the contractor to identify an erosion control product that complied with the project's design and installation parameters. "Use of erosion control matting enabled us to reduce erosion control costs," said Mark Rhodes, with the Texas Railroad Commission. "Also, the erosion control material was more aesthetically compatible with the reclaimed landscape." The commission's design called for a terrace ditch to be constructed midway up the reclaimed spoil slope to catch and collect water. Commission engineers selected spoil slopes, ranging from 5% to 8%, to build reinforced grassed waterways to drain the collected water from the terrace ditches. This was done instead of dropping the water at steeper slope location in rip rap- or concrete-lined channels. Enkamat's three-dimensional geomatrix of heavy nylon monofilaments is 95% open space that aids root growth. Its root-reinforcement system resists the hydraulic lift-and-shear forces created by high-volume discharges of water. In addition, fine eddy turbulences are prevented from isolating and uprooting individual roots and clumps of vegetation. Enkamat is flexible and lightweight. This makes it easy to install. And, because grass grows into it over time, it "disappears" after installation. Between 12,540 and 14,200 m2 (15,000 and 17,000 sq yds) were installed in the waterway using 150-mm (6-in.) staples to fasten the matting, said contractor Dale Blackstock. "It was easy to use; no problem at all to put down." Blackstock selected Enkamat from a list of eight different channel lining materials described as acceptable in the commission's design specifications. The design specifications were based on the results of channel-lining performance tests conducted by the Texas Department of Transportation. Rhodes said that the commission's Abandoned Mine Land Reclamation program had installed Enkamat on other abandoned uranium mines and on an abandoned surface lignite mine near Austin. "Pretty much all of our installations of Enkamat have worked out well," he said. "There have been no failures. The reinforced grass waterways have performed as designed."

Jan 1, 1998

By Baojie Zhang

The main goal of this study was not only to investigate the effectiveness of the FGX Dry Separator for removing pure rock from run-of-mine coal producing a better feed stock for conventional coal preparation plants but also to optimize the FGX Dry Separator performance for producing a salable clean coal product without using the conventional wet coal preparation processes. A Model FGX-1 Dry Separator with feed throughput capacity of 10 tph was extensively tested at the Illinois Coal Development Park using two coal samples having distinctly different cleaning characteristics. Statistically designed experimental programs were conducted to indentify critical process variables and optimize FGX Dry Separator performance by systematic adjustments of critical process variable parameters. The coal cleaning performance of the FGX Dry Separator was evaluated for the particle size range of 63.5 x 4.76 mm in most cases, although FGX Dry Separator feed consisted of nominal -63.5 mm run-of-mine coals. The best cleaning performance obtained from the FGX Dry Separator is described by specific gravity of separation (SG50) and probable error (Ep) values of 1.98 and 0.17, respectively. The SG50 and Ep values for individual size fractions were as follow: 1.90 and 0.12 for the +50.8 mm size fraction, 1.95 and 0.18 for the 50.8 x 25.4 mm size fraction, 2.01 and 0.19 for the 25.4 x 12.7 mm size fraction, and 2.03 and 0.23 for the 12.7 x 4.76 mm size fraction. These process efficiency measures produced a clean coal with ash content of 13.38% from a feed coal with ash content of 34.45%. Ash content of tailings and middlings streams were 85.09% and 39.57%, respectively. Total sulfur contents of corresponding streams were 3.87%, 4.68%, 6.87%, and 4.62%. For a relatively easy to clean Illinois No 6 seam coal (Cleaning Index: 0.72), only about 0.42% of the clean coal (i.e., 1.6 float fraction) present in the feed was lost to the tailings stream. For a relatively difficult to clean coal (Cleaning Index: 0.53), about 0.98% of the clean coal present in the feed was lost to the tailings stream.

Jan 1, 2012

By Cliff Holloway

The past year has been difficult for Canada's primary industries. The mining, oil and forestry industries have been hit by low prices and a reduced demand for natural resources. Foreign competition, militant environmentalists, the breakdown of the Asian and European economies and Canada's shrinking dollar have all put additional pressures on the commodity purchaser to buy smarter. It is easy to appreciate why operations and maintenance supervisors want the best performing product. It makes good sense. The challenge is to source that quality product while staying within the budget. The bottom line (price), however, often becomes the control- ling factor, usually at the expense of quality and performance. This is short-term thinking, often with expensive consequences.

Jan 1, 1999

By Jian Liu

The study aims to leach copper from a low-grade flotation middling by optimizing the leaching process using response surface methodology. The effect of key parameters, i.e., sulfuric acid concentration, nitric acid concentration and leaching time, on the leaching efficiency was investigated and a quadratic model was suggested by the methodology to correlate the variables to the efficiency. The results indicate that the model is in good agreement with the experimental data at a correlation coefficient (R2) of 0.97 and the most influential parameter on efficiency was identified as sulfuric acid concentration. The optimum conditions for copper leaching from the middling were identified as sulfuric acid concentration at 103.74 g/L, nitric acid concentration at 12.50 g/L and leaching time of 30.98 min; under such a condition, an average leaching efficiency of 93.16% was achieved from the middling.

Jan 1, 2011

By L. Zhou, J. P. Rider, T. W. Beck, J. A. Organiscak, Y. Zheng

The U.S. National Institute for Occupational Safety and Health (NIOSH)’s Pittsburgh Mining Research Division (PMRD) recently developed a series of models using computational fluid dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations in an exhaust curtain working face. CFD models utilizing species transport model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The study illustrates the gas distribution in the slab (second) cut. The following scenarios are considered in this study: 100 percent of the discharge redirected back toward the face on the off-curtain side; 100 percent of the discharge redirected back toward the face, but divided equally to both sides; and 15 percent of the discharge redirected toward the face on the off-curtain side, with 85 percent directed toward the return curtain. These models are compared against a model with a conventional scrubber discharge where air is directed away from the face into the return. The models were validated against experimental data, proving to accurately predict sulfur hexafluoride (SF6 ) gas levels at four gas monitoring locations. This study includes a predictive simulation examining a 45° scrubber angle compared with the 23° angle for the 100 percent redirected, equally divided case. This paper describes the validation of the CFD models based on experimental data of the gas distribution results.

Jan 1, 2017

By L. Zhou, J. P. Rider, T. W. Beck, J. A. Organiscak, Y. Zheng

The U.S. National Institute for Occupational Safety and Health (NIOSH)’s Pittsburgh Mining Research Division (PMRD) recently developed a series of models using computational fluid dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations in an exhaust curtain working face. CFD models utilizing species transport model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The study illustrates the gas distribution in the slab (second) cut. The following scenarios are considered in this study: 100 percent of the discharge redirected back toward the face on the off-curtain side; 100 percent of the discharge redirected back toward the face, but divided equally to both sides; and 15 percent of the discharge redirected toward the face on the off-curtain side, with 85 percent directed toward the return curtain. These models are compared against a model with a conventional scrubber discharge where air is directed away from the face into the return. The models were validated against experimental data, proving to accurately predict sulfur hexafluoride (SF6 ) gas levels at four gas monitoring locations. This study includes a predictive simulation examining a 45° scrubber angle compared with the 23° angle for the 100 percent redirected, equally divided case. This paper describes the validation of the CFD models based on experimental data of the gas distribution results.

Jan 1, 2018

By M. Modis

According to previously established theoretical analysis and under certain conditions, a critical sampling grid can be determined for an earth-related space-distributed natural variable. Sampling above this critical limit adds little to the mapping results, while based on this limit the ideal process of reproducing the original phenomenon is theoretically defined. The objective of this paper is the application of the above theory to the Klidi lignite deposit in Florina, Greece, where Public Power Corporation (Greece) has conducted a sampling campaign to estimate the deposit thickness and its heating value. Data acquired for these two variables were analysed in the space domain in order to derive their respective correlation functions. The structural analysis of the deposit generated two covariance models, one for the thickness and one for the heating value, from which the critical sampling grid was identified. The conclusion drawn is that in some parts of the deposit the sampling grid is denser than required. Finally, an optimal sampling grid is proposed in order to gain the maximum information at the lowest cost.

Jan 1, 2006

By John A. Riddle

Some of the pitfalls and problems in selecting and applying corrosion-resistant materials in uranium plants are discussed, together with some suggested solutions. Includes some cost data.

Jan 1, 1979

By A. Khoshnevisan

Molybdenum resources around the world are mainly associated with porphyry copper ores. Molybdenite (MoS2) is the main Mo mineral that has rhenium in its crystal lattice. This paper investigates the recovery of rhenium and molybdenum from a molybdenite concentrate using a hydrometallurgical treatment method. The molybdenite concentrate is leached with nitric acid and subjected to solvent extraction to recover and separate rhenium and molybdenum from the leached liquor. The effects of pH and the chemicals? concentration on extraction characteristics of Mo and Re are investigated to define the best condition for selective extraction of these metals. The tested leached liquor contained of 8.2 g/L Mo, 1.5 g/L Fe, 0.5 g/L Cu and 60 ppm Re. A good extraction efficiency, up to 94%, was achieved for Re from the leached liquor, where the extraction of other metals, such as Fe and Cu, was negligible. In particular, at very low pH, rhenium is extracted selectively from solution, while the extraction of molybdenum is less than 10%. After removing rhenium, molybdenum was extracted with LIX984N. The selectivity of molybdenum extraction over other metals in solution was significant. Nearly 94% of molybdenum can be extracted from the solution at a pH value of -0.12, without any interference from other metal ions such as copper and iron.

By John W. Straton

Following the completion of the paper presented in February, 1972, data were received from many other mines and some original respondents submitted more complete questionnaires. The computer program was changed to permit the results to reflect more clearly all the data reported by the mines. The original paper was revised to reflect the new information. There were significant changes in some numerical values, particularly where the size of the sample changed appreciably. Some limited samples considered originally in arriving at conclusions were not relied on in this revision. The revised tables and text are of the same design and format as the original paper.

Jan 1, 1972

By Crone Duncan

The search. for massive sulphide orebodies is steadily being extended to greater depths as well as expanding outward into the large portion of the earth's surface where the sulphide bodies are deeply weathered. Massive sulphide orebodies are generally not large in dimensions. They are not like disseminated type sulphide bodies that form large ground exploration targets that can be detected at greater and greater depths simply by increasing the geometrical spacing between the geophysical transmitter and receiver. In¬creasing the transmitter-receiver spacing with massive sulphide bodies eventually "waters down" the anomaly from the body until it disappears into noise. If high surface conductivity is present, as is common in areas of deep weathering, the problem is compounded by the increasing response of the surface layer, as the receiver-transmitter spacing is expanded. The search to greater depths has important implications other than just detection of the orebody. Drilling costs are increased and the probability of missing the target are increased. Missing an orebody is an expense that is difficult to evaluate in dollars per line mile of survey especially since one does not know the value of what was missed. A ground Pulse EM method has the capabilities of solving the problems of deeper exploration particularly in areas of surface weathering it can attain deep penetration without large coil spacings, it also provides information from a complete range of frequencies. The method has other operational advantages since it is free of geometrical restrictions as to coil alignments and can operate in areas of high power line noise.

Jan 1, 1975

By Tim Lundquist

Disa Technologies Inc. provides innovative, sustainable solutions for mineral processing and remediation through its patented High-Pressure Slurry Ablation (HPSA) technology. HPSA processes solid feed material in slurry form, propelled by high pressure pumps through opposing nozzles that generate impinging jets within a collision housing. This process induces particle-to-particle collisions in a high energy zone, creating intergranular fractures along grain boundaries. In our batch scale and continuous operating testing, we have found that controlling key processing variables such as nozzle velocity, slurry solids percentage, and the number of passes can allow for controlled size reduction and maximum mineral liberation. Since 2018, Disa Technologies has demonstrated the versatility of HPSA by testing it on diverse materials, including phosphate, copper, uranium, vanadium, zinc, rare earth elements, lithium, nickel, mineral sands, gold tailings, and more. The intent of this paper is to present an overview of our test results describing in detail impacts on size reduction, recovery, and grade with a focus on HPSA's adaptability across ore types. Looking forward, it explores the potential to process materials such as DR-grade iron, clay, PGMs, bauxite, and various tailings. Additionally, it examines planned advancements in HPSA technology, including optimized nozzle spacing, higher capacity models, improved tonnage-to-footprint ratios, enhanced maintenance features, and expanded nozzle configurations.

Jan 1, 2025

By W. Clark Ashby

Productivity is a fascinating concept. Like motherhood or apple pie, we know it as a good thing. Just what it means is not so clear. To a coal miner we assume it means tons of coal hauled from the mine. To the company president it means profit after capital, labor, and other costs have also been reckoned. To the government economist it means output in a balance of payments. What does it mean to the biologist, and can reclamation really be productive? In this paper we discuss productivity from a biological viewpoint, give some yield data for various types of reclamation plantings, and discuss how our demand for or acceptance of differing kinds of productivity is tied up in bigger questions of land use, environmental stability, and resource allocation.

Jan 1, 1981

By Reginald E. Reid

Mining on Bureau of Land Management (BLM) administered lands is affected by Federal laws and regulations requiring the mining industry to plan for the environmental consequences of surface disturbance. Regardless of the requirements for obtaining a claim, permit, lease or contract to mine, a notice or a mining and reclamation plan will be submitted and an acceptable environmental document must be prepared prior to mining. A bond may be required based on the results of the environmental evaluation, public interest and the operator's past history of compliance. In several areas, Federal requirements are different from California's requirements under their Surface Mine and Reclamation Act (SMARA). Therefore, the BLM is negotiating with the State in order to work out problem areas of responsibility and duplication of effort.

Jan 1, 1984