Search Documents

By L. J. Habegger

This paper considers the potential water quality impacts of future energy scenarios which project an approximate doubling of coal utilization from 1975 to 1985. The major impacts estimated for coal extraction are related to effluents from unregulated activities (reclaimed areas prior to stable vegetation) and pollutants (e.g., metals and ammonia). Where applicable, the EPA effluent guidelines to be in effect by 1983 reduce the impact of individual sources to low levels. For example, total suspended solids and acidic discharges are to be regulated to levels generally below recommended water quality standards for receiving streams. However, implementation of these guidelines, particularly for coal extraction, has not been demonstrated on a wide scale. Water quality is not expected to be a major constraining factor for increasing capacity of coal fired utility and industrial boilers. Water quality control has not been demonstrated on a commercial scale for coal conversion to synfuels, but adequate control technologies appear to be feasible.

Jan 1, 1978

By J. Dubbert, T. H. Jones

"This paper describes a rib-control methodology that uses standing support to provide most of the lateral resistance to the rib. The method is analyzed, and its boundary conditions for rib control are described. In this method, an animal-fencing mesh product covers 80 percent of the rib surface and is sparsely bolted to the rib. Can supports or other similar stiff supports are installed primarily as roof support for the entry. As the rib spalls and dilates, the mesh catches the material and expands, pressing against the standing support. Mining proceeds, and vertical roof loads increase the normal force on the Can supports, causing friction at the top and bottom of the support to go up, thereby improving lateral resistance to rib swelling.At one mine in the western United States, this method has proved excellent at preventing the buildup of rib spall. It substantially reduces the number of bolts used for screen installation, improves installation efficiency, reduces manual labor and provides more rib coverage than many screening methods. Because standing support is typically part of the roof-control plan in longwall tailgates, no additional standing-support costs are incurred. IntroductionRib safety in underground coal mines is an oft-studied topic because ribs are high-hazard areas. An overview of early rib safety research can be found in Jones and Mohammed (2014). There is a significant difference between rib support and rib control. Support improves safety through the installation of strengthening elements, such as bolts and dowels, designed to reduce rib spalling. Although spall reduction is preferred, controlling how the rib fails is enough to ensure safety in some situations. Rib control uses external elements to provide confinement, thereby holding sloughed material in place, or to prevent falling rib material from striking mine personnel. This paper presents a study of a control method used on the pillar side of a longwall coal mine tailgate in the western United States."

Jan 1, 2015

By M. Downing

This paper gives a brief overview of impacts of coal blending on coal-fired power plants performance and discuses the preliminary results of an on-going study aimed at evaluating the effect of coal properties on the effectiveness, compatibility and thermal reactivity of coal blends. Plant survey studies reported no significant impacts on an existing plant designed for a high rank coal when switched to a blend of low-and high-rank coal. However, slight modification of some aspects (handling, fuel storage/stockpile, transportation, preparation, and general housekeeping) of plant design and operation may be necessary. The preliminary results of an on-going study at the Mineral Industry Research Laboratory shows that more compatible and better blends could be made from coals where ranks are closer than from those where ranks are far apart.

Jan 1, 1997

By K. A. Foo

Minproc Resources Inc. is developing a tailings retreatment project in Bolivia at the Colquiri zinc-tin-silver mine, in the Bolivian Andes. Mining at Colquiri has been continuous since 1940 and COMIBOL, the Bolivian state mining company, has owned and operated the underground mine since 1964. There are 10 million tonnes of tailings at Colquiri containing 0.51% Sn, 4.21% Zn and 50 g/t Ag. Minproc plans to mine and concentrate the tailings at 1.15 million tonnes per year to produce feed for pyrometallurgical upgrading. The tailings are moderately complex, with cassiterite grain size ranging from 200 to 5 pm. The marmatite (ZnFeS) in the tailings is relatively easily recovered, with zinc recovery of 80% to a 40%-45% Zn concentrate. The major problem with the zinc metallurgy is that the marmatite is complexed with iron, which results in iron contents of 14%-17% Fe in concentrate. This makes the product very difficult to sell because of the low Zn:Fe ratio. Most zinc smelters require a Zn:Fe ratio of 6:1 or 7:1, whereas this concentrate has a 3:1 ratio. Concentrate sale terms are therefore unfavorable, and the high cost of transportation from Bolivia to the smelters is an additional burden.

Jan 1, 1992

By Timothy O’Rourke, Karrie Buxton, Chris Lynagh, Daniel Dobbels, Frederick Vincent

The Doan Valley Storage Tunnel Project in Cleveland Ohio was constructed to control Combined Sewer Overflows (CSOs). It is a complex system of three tunnels ranging from 8.5 to 18 feet in diameter with a total length of about 2.3 miles that was put into operation in mid-2021. The project lies within and below the cultural, educational, and medical hub of Cleveland, which presented unique design and construction challenges. This paper provides a case history of the design and construction, with particular attention given to lessons learned in devising a large tunnel system that can carry both dry and wet weather flows constructed in rock with limited cover, within a flood plain area and vibrant urban center

Dec 1, 2022

By Gary Peach, Peter Mason

Planning and estimating progress rates and costs for tunnelling is always best done based on experience and historic precedent. Much precedent is available but the use of data monitoring, data mining and other retrieval techniques on modern TBM machines can enable this to be further expanded and refined. Advance rates can be related much more closely to rock types as can associated rock bolt and mesh/ shotcrete requirements. This in turn can lead to a further refinement in best likely combinations of equipment, such as shotcrete jumbos, better selected for the anticipated conditions, rather than the potential advance rates of the machine. Efficient and timely construction of the tunnel will also be linked to times needed for finishing work, such as contact and void grouting and to how this can be initiated while the TBM is still in operation, in order to save overall construction time. Indeed, this in turn may affect the most preferable layout and construction details of the permanent tunnel. Considerable experience has been gained in the use of two large diameter TBM tunnel drives through the Himalayas at the Neelum-Jhelum hydropower project in Pakistan. All the above aspects will be discussed in the paper based on the considerable experience and data which came from that operation, including appropriate measures in highly stressed areas potentially subject to rock burst.

Jun 13, 2021

By Ibezim J. Anazia

Electrothermal production of elemental phosphorous (P4) generates substantial amounts of highly toxic phossy water and sludges. Because of their high phosphorous content and lack of reliable processing technology, large tonnages of these hazardous wastes have accumulated from current and past operations. To date, the sludges are stored in ponds or above ground in special containment vessels at various locations around the country. Two samples of electric furnace phosphorous sludge obtained from the Tennessee Valley Authority (TVA) in Muscle Shoals, Alabama and FMC Corporation in Pocatello, Idaho were investigated using physical separation techniques to recover the elemental phosphorous in the sludge and to render the residual material non-hazardous. The techniques tested include sizing, froth flotation and dispersed air oxidation. Flotation and sizing produced concentrates containing 69 -90% P4 with a recovery in the range of 60 -87%. Dispersed air oxidation of the fines and tailing products was effective in removal of an additional 10 -15% of the P4 in the sludge.

Jan 1, 1991

By J. P. Ulery

As a result of several recent methane/dust ignitions in surface auger and highwall mines, the U.S. Bureau of Mines investigated the occurrence of methane gas at these operations. Three mine sites were visited in western Kentucky and one in western Pennsylvania to collect run-of-mine coal samples for gas content determination using the modified-direct-method (MOM). Results indicate the samples emitted small quantities of methane, carbon dioxide, and nitrogen. Either methane or nitrogen was the predominant gas released. The same gases were released after crushing the samples for residual gas content; however, nitrogen was the primary component of this fraction. Total ~as contents ranged from less than 0.01 cm /g to 0.54 cm3/g. The hydrocarbon gases probably originated during coalification. Other gases may have originated partially as a byproduct of coalification and partially as a result of other, near-surface processes. The data suggest that although methane quantities are small, desorption could occur at near surface conditions prior to mining. The desorbed methane could accumulate as a free gas in fractures in the coal bed or roof rock. When these fractures are penetrated by the auger, methane could rapidly enter the whole atmosphere possibly creating explosive conditions.

Jan 1, 1994

By Darrell V. B. . McClarty

In 1996, Rio Algom, Denison Mines and the Elliot Lake Research Field Station (ELRFS) formed a consortium to implement a regional environmental information management system (REIMS) for the Elliot Lake area in Ontario, Canada. ELRFS is an affiliate of Laurentian University in Sudbury, Ontario, The discovery of uranium in the Elliot Lake region in post-World War II led to the development of 12 mines and 11 associated mills between 1955 and 1958. During the late 1980s, declining world demand for uranium, combined with the discovery of high-grade uranium ore in other areas of the world, made the Elliot Lake mines uneconomical. As a result, all area mines ceased opera¬tions by the end of 1996. The eight facilities and three tailings management areas operated by Denison Mines and Rio Algom's five mining waste management areas contain 150 Mt (165 million st) of potentially acid-generating tailings. The areas cover 13.2 km2 (3,265 acres) and receive drainage from an additional 13 km2 (3,212 acres). The primary objective of the joint initiative was to implement a personal-computer-based, regional, environmental-information management system for managing historical data and ongoing environmental programs in the Elliot Lake region. The Elliot Lake consortium decided it needed an information system with an integrated, process-oriented and requirements-driven approach to collect and manage the environmental information. Following a study of environmental information management systems currently used by the mining industry, the consortium decided to base REIMS on the "Envista" product. This is a commercially available, environmental information management system marketed by Envista Technologies of Saskatoon, Canada.

Jan 1, 1999

By Steve Kral

"Repairing and replacing the nation’s aging and crumbling infrastructure has become a major issue with the American public. It is no secret that the upkeep of roads, tunnels, bridges, and water and waste water facilities has been neglected for decades. Cities, states and towns across the United States are now grappling with these issues, ones that will take decades and billions of dollars to fix.Because of this infrastructure issue, the North American tunneling industry is flourishing. Cities across the country are looking to go underground to alleviate traffic issues, transporting water and waste water to more people in more efficient ways.In October, the seventh annual Cutting Edge conference was held in Atlanta, GA. Put on by the Underground Construction Association of SME and Britain’s Tunnelling Journal, about 175 tunneling and underground construction professionals from around the world attended. Attendees included owners, designers and contractors. An accompanying exhibit included 28 companies.The theme of the two-day conference was Advances in Tunneling Technology. Speakers examined the latest advances in tunneling technology, its methodology and how these advances can be harnessed to assist upcoming major tunneling projects. The conference featured a tailored, high-end, single-track program of subject-specific presentations that focused on innovation and practical experience. Two in-depth panel discussions at the end of each day were also included.Patricia Mulroy was a keynote speaker on Monday. She is senior fellow for climate adaptation and environmental policy at The Brookings Institution. Like many others, Mulroy believes the U.S. infrastructure in in a state of disrepair. But, she said, no one wants to talk about it. “We need to have a conversation about infrastructure. We cannot be afraid to talk about building it and the cost.” For this to happen, though, the nation needs leadership."

Dec 1, 2018

By James Corcoran, Richard McLane, Matt Neuner, Joseph DeMello, Hugh Davies

The Los Angeles County Metropolitan Transportation Authority (LA Metro) Purple Line Extension Section 1 (PLE1) is a $3.12 billion USD design-build, underground heavy rail project, connecting an existing station at Wilshire Blvd. and Western Ave. and extending 3.92 miles under Wilshire Blvd, terminating approximately 550 feet west of Wilshire and La Cienega Blvds. The project alignment runs immediately adjacent to the La Brea Tar Pits, world renowned for Pleistocene fossils and continuous seepage of asphaltum (locally known as tar) and gas in an urban setting. This paper presents a successful case history of the planning, design, and construction efforts to safely construct the bored tunnels through Reach 3 of the alignment (between Wilshire/Fairfax Station, and Wilshire/La Cienega Station), in a designated Methane Zone in the City of Los Angeles. Historical context on decades of challenges and studies is summarized. Further, this paper outlines the pro-active partnership between the Owner: LA Metro, the Design Builder: Skanska-Traylor-Shea Joint Venture, and geotechnical design services provided by Golder Associates to safely manage pressurized face tunneling through a confined gas zone near the La Brea Tar Pits. Specifically, a program of in-situ oxidation and soil gas extraction was designed to test and analyze risks associated with pressurized face TBM tunneling through the complex subsurface geological conditions, then implemented during construction. In advance of tunneling, a network of wells was used to draw air into the gas zone to oxidize the 6,500 ppm hydrogen sulfide gas, as well as determine methane recharge rate. During TBM tunneling, the wells were converted to a gas extraction system to evacuate, filter (H2S) and burn (CH4) the gas as the Tunnel Boring Machine passed, providing a preferential pathway for the gas to migrate toward extraction wells, and preventing the migration to adjacent buildings. The team extracted and treated 3,857,000 cubic feet of mostly methane gas over 40 days as the TBMs passed through the zone. Gas behavior, pressures, and concentrations were monitored not only from the extraction system, but also in basements and utility vaults along this section of the alignment.

Jun 13, 2023

By James W. Echerd

Anthracite preparation developments, particularly in the early days of the anthracite industry, formed the basis for the modern coal preparation plants that have become so essential to the coal industry today. The anthracite industry, from early in the 19th century until relatively recently, was a leader in mining, preparation and marketing of coal, and played a leading role in the development of the industrial America we know today. Anthracite was discovered in America in about 1760--the story of Necho Allen is well known--but the rediscoveries leading to mining operations took place about 50 years later. The Wurtz brothers in 1815 at Scranton, the Smith brothers at Wilkes-Barre in 1807, Beach in Hazleton in about 1814, and Boyd in 1816 at Shamokin were all instrumental in promoting early mining and marketing of anthracite (J3. The early canals and railroads were built for the specific purpose of moving anthracite to the market areas. Eventually, the industry grew until, in 1917, it reached a production zenith of a little over 100,000,000 tons, representing about 20 percent of the total coal output in the United States. Almost half of the anthracite produced that year was consumed for domestic heating, a utilization that had dominated the industry for almost 100 years. Initially, anthracite had to be used by gunsmiths and blacksmiths, after which had followed the consumption of extensive quantities for railroads, blast furnaces and foundries, and electric power generation. Most of the markets have been lost to coke, oil, and natural gas. Near the anthracite regions, however, significant quantities are still used for domestic heating, power generation, carbon black manufacture, blending with bituminous coal to make metallurgical coke and fuel, and for other industrial purposes. Thus, anthracite production has not been entirely committed to history, but remains an active industry that follows modern practices in the mining, preparation, shipping, and utilization of a fuel that is still a valuable adjunct to the national economy. In fact, its inherent low sulfur content may make it an important fuel of the future. Estimates indicate there are reserves of anthracite to last for 300 years at a consumption rate of 50,000,000 tons/year. Anthracite Preparation Yesterday A 170-year history of the anthracite industry obviously is not the purpose of this discussion. A complete history of anthracite preparation, the rather unglamorous step in the processing of "mine run" hard coal to make it suitable for the user, is also not practical. Hence, the purpose of this report is to trace the development of some of the most important processes used through the years to meet a part of the demand for energy developed by our modern society. Anthracite preparation in the early days of the industry consisted solely of separating slate from the coal, by hand, underground (Z). This method prevailed for almost 20 years until wrought iron hand rakes were introduced to separate the large and small sizes. Shortly thereafter, the first attempts were made to size and clean the coal aboveground. The coal was dumped on a perforated cast iron plate, and men used sledge hammers to break the larger pieces into smaller sizes suitable for the market. The smallest sizes--that is, the material that went through the plate--were thrown away because they had no value at that time--a concept that existed for many years and actually was the basis for the subsequent "river" coal production and the many silt banks which are landmarks in the anthracite region. The larger sizes, at that time, sold for 50 cents per ton. The Batten breaker, or roll crusher, was invented in 1844, followed soon thereafter by the Snell-Diehm breaker (A). The latter had disadvantages, including excessive waste and fixed product size, but it later was improved in these respects. A breaker was also developed at Minersville, Pa., at about the same time that processed 200 tons of coal per day, using roll crushers and circular screens (1). Handpicking, from the beginning of anthracite preparation, was an important part of the cleaning process and was still being practiced as late as 1950. It was this process that involved the "breaker" boys of coal region lore. How much good handpicking accomplished depended on how much impurity was present in the coal--the more the impurities, the greater the reduction in ash. Thus, high-impurity streams were significantly improved, whereas picking of relatively clean coal was mainly to show an effort to make a quality product. As indicated, picking is largely a visual operation. It was and is wasteful of coal in the larger sizes since some good coal is always associated with the bad. However, it was probably much more effective' in the larger than the smaller sizes.

Jan 1, 1971

And a new generation of safety culture experts are telling mining companies how to use it: It is a situation that is still too common in the mining industry: the latest personal protective gear is in place. The safety rules are known and followed. And then, in a moment of inattention or carelessness, a mistake is made and someone gets hurt or killed. Common wisdom claims that such accidents are impossible to eliminate entirely. Mining is dangerous, and some miners will always be hurt and killed. An increasing number of mine safety experts, however, reject the common wisdom. A year with zero mining deaths is possible, they say; with the use of one of the newest weapons to the mining industry in the safety war: the concept of safety culture. Safety culture refers to the set of attitudes, beliefs, perceptions and values that influence safety in the work environment. It is also sometimes called the way an organization behaves when no one is watching. Robert Peters, of the Office of Mine Safety and Health Research (OMSHR) at the National Institute for Occupational Safety and Health (NIOSH), describes safety culture this way: ?It?s what?s believed on a day-to-day basis. For example, if a miner sees a workplace hazard and he truly believes that his boss wants him to identify the hazard and bring it to the company?s attention, that would be an example of a positive safety culture.?

Jun 1, 2010

By L. Barry Phelps

The application of an open-pit Materials Handling Simulator (OPMHS) to analyze mine planning and scheduling problems in large surface mines is discussed. The mine chosen for this application employed a large stripping dragline working in tandem with a shovel-truck haulback system for removing overburden. Large bottom-dump trucks were employed behind a coal loading shovel to transport the exposed coal out of the pit. Specifically, the current operations and the recommendations for short term and long term improvements were simulated on OPMHS. The effects of changing the operating parameters of the equipment on the total system were evaluated. Several alternatives were also studied for the best use of the existing equipment if the current operating parameters could not be improved upon. The results of the application are discussed.

Jan 1, 1978

By M. S. Davis

The Tek Process can produce masonry products such as bricks, roof or wall tiles, and block from virtually any inorganic waste. In the process the aggregate raw materials, portland cement, water and common chemicals are first mixed together; then mechanically subjected to several thousand pound pressure per square inch. This causes a novel chemical reaction between the cement, chemicals and water; producing the "patented" Tek adhesive binder which holds the aggregate together in a stone-like mix. Simultaneously, the desired product shape is formed. The building modules can have strengths of 8000 p.s.i. (pounds per square inch) with completely sound aggregates utilizing air curing for a period of 28 days. With most aggregates, 3000 p.s.i. is achieved within 24 hours. Eventual strengths usually exceed 5000 p.s.i. with almost any raw material. Water absorption ranges from 5-7.5 percent. Both absorption and strength figures are superior to the most rigid of any and all A.S.T.M. specifications for the highest quality bricks. In most locations, the product (when brick shaped is called Tekbrik) can be produced significantly more economically than can comparable grades of clay or other bricks, be- cause almost any inorganic waste materials or pollutant can be used as a raw material. The process results in a lower manufacturing cost as compared to clay bricks; fuel cost to operate a clay kiln represents a substantial portion of the total cost. Capital expenditure for a Tek plant also is lower due to the large investment in clay kilns. Transportation savings also are important, clay brick factories must be very large because the kilns are uneconomical unless they are large. Most bricks are manufactured at the sites of clay deposits in relatively uninhabited areas. The cost of transportation to the job site represents a considerable percentage of the selling price.

Jan 1, 1974

By P. Henderson, M. E. Morris, W. A. Johnson, F. D’Alessandro, D. Wilton

"The objective of this research is to develop and apply computer models to evaluate the potential lightning impacts on underground coal-mining. These models can then be utilised to assist in the design of effective controls. This project will provide a significantly improved level of knowledge and control over current lightning abatement techniques. The findings may also be applied to open cut and coal preparation situations. Computer modelling identified that by isolating cased boreholes from underground conductive media such as roof mesh, and placing spacings between roof mesh the risk of an ignition can be reduced by more than a factor of ten. These controls should be applied in conjunction with minimising the potential for a flammable atmosphere to exist underground and ensuring that there is no transmission medium for the lightning to reach the atmosphere. INTRODUCTION The objective of this research was to develop and apply computer models to evaluate the potential lightning impacts on underground coal-mining. These models could then be utilised to assist in the design of effective controls. If successful this project would provide a significantly improved level of knowledge and control over current lightning abatement techniques. The direct potential for harm from lightning has long been recognised for the surface facilities of coal mines. However recent events at Blakefield South in NSW on January 5 2011 (DTI, 2011) and at Sago mine in the USA in 2006 (MSHA, 2007) have suggested that there is potential for lightning to cause significant damage to the underground workings of a coal mine. A very detailed analysis carried out by as part of the MSHA investigation into the SAGO disaster by Sandia Laboratories identified at least ten other incidents over the past thirteen years where lightning had probably caused the ignition of a sealed goaf area of a mine (SANDIA, 2011). In addition there is a long history of lightning related incidents in South African coal mines (Geldenhuys, 1985). Fortunately in those cases no lives were lost. The event at Blakefield South has suggested that there may be the potential for ignition to occur in an active longwall goaf. The potential for a lightning strike to ignite a flammable atmosphere in an underground coal mine has been demonstrated from the past experience both here and overseas. It requires three things: • Lightning • A mechanism to convey the lightning underground to the flammable atmosphere • A flammable atmosphere."

Jan 1, 2016

By R. E. Le Messurier

GENERAL DESCRIPTION The mines are located at Broken Hill in the western part of New South Wales, Australia, 930 km west¬northwest of Sydney. Mining Methods Where pillars must be left between stopes, extraction of a block of ore between two or more levels is carried out in stages: 1) Stopes are mined overhand by horizontal cut¬and-fill stoping, or by long-hole stoping. The various methods of horizontal cut-and-fill stoping used are desig¬nated as: -Loader cut-and-fill stoping with horizontal blast¬holes and diesel load-haul-dump (LHD) units. -Open stoping with horizontal blastholes and com¬pressed air or electric scrapers, or with diesel or electric LHD units. Square-set timber stoping, where ground condition precludes open stoping. The backs are sup¬ported with timber square sets. Pattern rockbolting of the backs may be used as an intermediate stage between open stoping and square-set stoping. 2) Vertical pillars are mined by undercut-and-fill stoping or by vertical crater retreat stoping. 3) Where a horizontal pillar has been formed below the level above the primary stope, this level pillar, usually 6.1 to 8.2 m in depth, may be mined by over¬hand square-set stoping or by undercut-and-fill. Long-hole stoping is used at the Zinc Corp. (ZC) and New Broken Hill Consolidated (NBHC) to mine parts of the zinc-rich A and B lodes. Drilling is carried out from drill drives and, in some cases, sills. Hole sizes used are 165 mm (61/2 in.), 110 mm (4'h in.), and 65 mm (21/2 in.) nominal diam with hole lengths being limited to 50, 30, and 20 m respectively. Ammonium nitrate-fuel oil (ANFO) and water gel explosives are used. Broken ore is loaded from drawpoints at the bottom of the stope using rubber-tired diesel-driven LHD units which deliver ore to an orepass. Annual production at Zinc Corp. and NBHC accord¬ing to mining method is given in Table 1. At Zinc Corp. mining is being carried out at depths varying between 200 and 832 m. At NBHC it ranges from 528 to 915 m below the surface. The average travel time to the stope is 30 to 45 min. GENERAL ORE BODY REQUIREMENTS Size, Shape, and Dip There are six separate lodes which carry minable ore in the mines of Zinc Corp. and New Broken Hill Consolidated. The lowest of these and the main ore bodies presently being mined at Zinc Corp. are the lead lodes, consisting of a siliceous fluoritic ore body (No. 3 lens) and overlying it a calcite rhodonitic ore body (No. 2 lens). Each possesses characteristic ratios of lead, silver, and zinc, although the grade within each lens is variable, in places being as high as 30% Pb. There are also low¬grade portions which consist chiefly of poorly mineral¬ized rhodonitic material. No. 3 lens terminates within the Zinc Corp. leases, while No. 2 lens continues into the NBHC leases where it continues to provide a significant proportion of pro¬duction from the mine. Overlying the No. 2 lens are the various zinc-rich ore bodies. In ascending sequence these are lower No. 1 lens, upper No. 1 lens, A lode, and B lode. A typical assay for the small No. 1 lens group ore bodies is 8% lead, 50 g/t silver, and 20% zinc. The `A' lode is a large low-grade ore body in which the higher grade sections assay 4% lead, 30 g/t silver, and 10% zinc; larger quantities of lower grade ma¬terial also occur. B lode, the main zinc lode, typically assays 5% lead, 30 g/t silver, and 17% zinc. B lode increases in size as it extends south, and in NBHC is a major ore body, contributing about 52% of the production. All the lodes pitch south, the average pitch being 0.52 rad (30°) in the Zinc Corp. leases and rather flatter than this in the NBHC leases (see Figs. 1-3). The ground is all competent rock. Production requirements at Zinc Corp. are 900 000 t and 1 200 000 at NBHC.

Jan 1, 1982

By SUHAINA ISMAIL, NORLIA BAHARUN, SHAIK ABDUL RAHMAN, WAN NUR SYAFIQAH ANUAR, MOHAMMAD REZAEI ARDANI

Refractory gold ore contains sulfide minerals like pyrite, chalcopyrite and sphalerite that are difficult to be directly leached by cyanidation or by lixiviants such as thiourea and halides. In such cases, it is necessary to perform oxidative pretreatment of the ore to oxidize the sulfide matrix, and gold particles can be exposed to the solution during the leaching process [1]. In recent years, hypochlorite and chloride solutions have been introduced as alternative materials for hydrometallurgical methods of gold extraction instead of cyanide solution [2]. A previous study by Hasab et al. [3] reported that the gold dissolution rate in hypochlorite solution was higher than in the cyanidation process, due to the presence of hypochlorous acid (HOCl) as a strong oxidizing agent. In a hypochlorite leaching system, the change in pH can influence the presence of oxidant species in the solution: the hypochlorite ion (OCl−) is stable in pH greater than 7.5, HOCl can be found in pH between 4.0 and 7.5, and aqueous chlorine (Cl2 (aq)) is the predominant oxidant when pH is below 4.0. As HOCl is the most effective oxidizing agent for gold extraction, pH should be maintained in the range of HOCl stability [4].

By D. S. Choi, H. D. Dahl, D. L. McCain

The paper examines current room and pillar mining practice in the U.S.A. from the standpoint of rock mechanics. Consideration is given to the deformation characteristics of the roof formation and the coal seam as determined in the laboratory as well as in the field. The results can be utilized by the practicing mining engineer to improve current mine design practice.

Jan 1, 1982

By R. L. Wiegel

A well-defined geometric model for a mineral system and its liberation by size reduction is used to show the relationship between true volumetric particle composition and the composition estimates obtained by the measurement of linear intercepts or areas of simulated polished sections of particles. Based on this information, a transformation is developed between the areal measurements and the volumetric composition for this idealized mineral system. Key words: Gaudin random liberation model, Mineral liberation, Particle composition measurement

Jan 1, 2010