Search Documents

By S. Lu

The particle-bubble attachment and the rupture of formed aggregates in flotation cell were investigated in terms of turbulent regime. It was found that the particle-bubble collision rate is closely correlated to the energy barrier between particles and bubbles, and no adhesion takes place for the hydrophilic particle-bubble system due to the introduced ?capture efficiency? f(a) being zero. The values of an especially defined Weber number, i.e. the ratios of turbulent stress to aggregate strength in the inertial subrange of turbulence were estimated, the results showed that the detachment of a particle from a bubble involved in an aggregate is mainly caused by the turbulent stress only in the impeller zone, no bubble splitting occurs both in the impeller zone and in the bulk zone.

Jan 1, 1993

By Ben Roderds

The Waneta Expansion Project (WAX) is located near the existing Waneta Dam site at the confluence of the Pend d?Oreille and Columbia rivers, approximately 10 km (6.2 miles) south of Trail, BC, Canada. The WAX owners consist of a partnership between Fortis Inc., Columbia Basin Trust and the Columbia Power Corp. This design-build project was awarded to SNC-Lavalin in late 2010 and is expected to be operational in mid-2015. The WAX consists of a new 335-MW powerhouse, including two new Francis turbine units, each generating approximately 167 MW. The powerhouse is located downstream of the existing Waneta Dam, and will make use of excess water that would otherwise be spilled during the runoff season. Water will be funneled to the turbines through an intake structure and two 10.5- m (34.5-ft) diameter, concrete-lined Penstock Tunnels. A 10-km (6.2-mile) transmission line will connect the powerhouse to existing electrical grids. Redpath/FKCI Waneta Tunnelers (RFK) was subcontracted by the heavy civil contractor, the Aecon/SNC Lavalin (ASL) joint venture, to excavate the two penstock tunnels and install the cast-in-place concrete liner. RFK is a joint venture partnership between J.S. Redpath Ltd., an underground mine contractor located in North Bay, Ontario, and Frontier-Kemper Constructors ULC, a heavy civil tunneling contractor based in Nova Scotia, Canada. Since penstock tunnel excavation was planned using drill-and-blast methods with a significant grade of more than 17 percent, the combined experience of these two contractors was a perfect match.

Mar 1, 2014

By Madan M. Singh

Although roof bolting has been a major means of strata support for nearly two decades, little attention has been directed towards the design of bolt Installations. The variables involved are interdependent and their study complex. However, some simple tests may be employed to serve as guides to the efficient design of roof bolt systems. Local conditions are continually varying and are important to pattern design. This paper discusses such considerations and suggests techniques which may be employed to effect improved roof control with bolts.

Jan 1, 1967

By Emily Rose

The concept of risk management is applied to multiple aspects of the mining lifecycle including safety, mine design, business plan—anything that affects getting the ore to the mill for production. However, risk management is not a topic that can readily be taught in universities. Many situations require knowledge gained from experience to know how this impacts current and future operations. Recent graduates, who must develop and apply decisions based on geotechnical monitoring, likely have not developed “operational experience” and may not be aware of options and typical applications. Thorough resources that explain different monitoring systems, and when and how to implement them, are available for geotechnical professionals. Accessibility to this information can often cause information overload, leaving one unsure of where to start, without knowing where to start. This paper is intended to serve as a high-level overview of development practices, levels of risk, and risk tolerance for entry-level geotechnical and mining professionals who do not come from a geotechnical background. Summarized detail on typical monitoring practices, types of instrumentation, and how to communicate what the data indicates to key stakeholders are provided.

Feb 22, 2026

By M. D. Ross

Complex combinations of technical, economical, safety and environmental factors are causing mining engineers everywhere to review their operations. Naturally, some of the traditional methods still have a large role to play because they are, in certain circumstances still adequate and are well understood. But, as circumstances change, a new approach is required. The combination of technical and economical reasons for introducing Long- wall mining in some seams in the United States is associated with strata control. Other reasons include simplifications and improvement of ventilation, reduced coal dust, more output from each unit and crew, increased percentage of recovery from each area of the coal deposit, and reduction of rock dusting. The innovations which transformed Longwall mining from a cyclic to a continuous mining system were the armored conveyor and power loading machines, but the crucial breakthrough for application to high production was the development of the powered roof support, which at once gave the system the advantages of mastery of strata control, increased rate of advance, significant reduction of manpower, and increased safety.

Jan 1, 1974

By Larry A. Enloe

The 16-to-1 milling operation is Sunshine Mining Company's first new silver and gold producing facility. The 16-to-1 underground mine and mill are located approximately 64 km (40 miles) southwest of Tonopah, Nevada. Ore re- serves in the epithermal vein deposit are estimated at 0.91 Mt (one million st) of ore, at an average silver grade of 206 to 240 g/t (6 to 7 oz/st) and an average gold grade of 1.2 g/t (0.035 oz/st). The underground mine uses a large diameter blasthole stoping system of mining using highly mechanized rubber-tired equipment. The mill uses conventional cyanide leaching with countercurrent decantation and Merrill-Crowe precipitation. The mill start-up was in February 1982 resulting in the first pour of dore' in March 1982. The mill's present annual production is approximately 31.1 t (1.0 million oz) of silver and 264 kg (8500 oz) of gold.

Jan 1, 1984

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this study is to assess the impact of different reagents, such as limestone, lime, magnesium oxide, and sodium hydroxide, in experiments carried out in the single purification step and in two consecutive purification steps by raising the pH of a rare earth sulfuric liquor with the aim to remove or reduce the impurity concentrations in the rare earth sulfuric liquor. The choice for the best purification condition was made based on the minimum loss of rare earth elements (REEs), reagent consumption, and residue generation. The exploratory experiments show that it takes place in the two consecutive purification steps, the first one consists in dosing the limestone pulp until it reaches a pH of 3.5 followed by an addition of a lime pulp reaching a pH of 5.0. Under this condition, the results were a total removal of Fe3+, PO4 3− , and Th4+ ions and a reduction of 99%, 87%, and 37% w/w in the Al3+, UO2 2+, and SO4 2− concentrations, respectively, in the purified rare earth liquor. Furthermore, the lowest REE losses (8.3% w/w) and reagent consumption (4.3 kg/m3 ) and also a low residue generation (7.5 kg/m3 ) were observed in this condition. Despite reaching similar results regarding impurity removal, the experiments done with the addition of limestone, lime, magnesium oxide pulps, and sodium hydroxide solution in the single purification step, where the pH was raised to 5.0, presented higher REE losses (64.9%, 42.5%, 44.8%, and 60.9% w/w, respectively) and a higher residue generation (43.2, 25.1, 11.1, and 13.6 kg/m3 , respectively). This occurred due to the co-precipitation of salts containing rare earth elements in their composition. The experiments conducted with limestone, lime, and MgO resulted in a higher consumption of reagents, while the same result was observed when NaOH was used (4.3 kg/m3 ). In the experiments carried out with the addition of magnesium oxide and sodium hydroxide, the respective purified rare earth liquors presented a high concentration of magnesium, sulfate, or sodium, which could impact the quality of the marketable rare earth salts, whereas the salts obtained under the best condition observed in this study seem to be amenable for use as raw material in an attempt to obtain rare earth products with an acceptable chemical quality.

By M. E. Rossi

In mineral resources, geologic and mining data are acquired, processed, analysed, interpreted and modelled, eventually serving as basis to generate predictions and production plans. This is a complex process, and the resulting predictions are impacted by uncertainties related to the data itself and the processing methods and techniques used. They are also impacted by the subjective decisions made by the modeler(s) at each step of the way. Knowledge, biases, skills, and prior experience come into play in the long mineral resource evaluation development workflow. It is meaningless to discuss uncertainties without evaluating the associated risks that those uncertainties imply. It is important to quantify and assess uncertainty, and to evaluate and mitigate its consequences. This paper discusses (1) conceptual and practical sources of uncertainty; (2) the utopia of an “objective” uncertainty; and (3) the quantification and public reporting of uncertainty using geostatistical conditional simulations. The objective of this paper is to postulate that the industry is running out of reasons and excuses to ignore uncertainty and risk in project evaluation. This is done in two parts, with this, the first one, presenting a more conceptual discussion. Part 2 will present case studies from different types of mining projects and operations showcasing the impact that risk assessments can have in a mining project.

Feb 22, 2026

By D. N. Hillhouse

The economics of exploration target selection can be measured ultimately only against a company's success at developing mines. In the following brief history of the mine acquisitions of one company, Placer Development Limited, I try to identify the principal targeting parameters and the principal skills that came into play for each property and examine how these have changed with time. The process of target selection in exploration is directed: - first by corporate investment criteria which define objectives and acceptable levels of risk for pursuit of those objectives; - second by experience and skills which permit us to minimize risk; and - third by anticipation of future events relating to ore discoveries and changes in external risk factors.

Jan 1, 1984

By Collon C. Kennedy, Frances C. Hartogh, C. Joel Casburn

INTRODUCTION During the nineteenth century, the federal mining law was enacted with the objective of promoting the development of the western United States by providing unrestricted access to vast areas of federal land for mineral exploration. Prior to the advent of comprehensive federal, state and local land use plans, there was little, if any, regulation or restriction of mineral exploration activities. Today, the laissez-faire policies of the past that encouraged mineral exploration have gradually given way to the public's legitimate concerns regarding environmental protection, multiple use and planned land development. As a result, the contemporary prospector confronts a maze of statutes, ordinances and regulations with which he must comply to obtain the requisite approvals and permits before commencing mineral exploration on federal, state or private lands. This presentation will provide a broad overview of the exploration permitting process. The first section of this paper recommends certain general management practices to follow when attempting to obtain exploration permits. The second section presents two hypothetical cases, one involving a drilling program on private property in California and the other involving a drilling program and the removal of a bulk sample for metallurgical tests from federal land in Nevada. The cases are used to discuss jurisdictional issues and application of certain federal, state and county laws and regulations that pertain to mineral exploration. The final section contains a brief analysis of three important recent United States Supreme Court decisions. These decisions address the scope of the federal pre-emption doctrine as it applies to activities conducted on unpatented mining claims and the constitutional limits of permissible state and local land use and zoning regulations. PERMITTING PRACTICES The environmental impacts associated with mineral exploration generally result from the construction of drill sites, roads or trenches. Consequently, after the regulatory authority has considered the issues of permissible land use, the primary emphasis of the permitting process is to address problems related to pre-construction site identification and clearance, and post-construction site reclamation. The approaches taken to address these and other related issues vary with the scope of proposed work, the site, the appli-

Jan 1, 1987

By S. Daniel Thompson

In underground coal mining, the specification and control of belt and bunker capacities are complicated by (1) stochastic and intermittent conveyor loading, (2) a limited ability to reduce surge at the mine face, and (3) occasional overlapping of loading from two or more mine faces on the conveyors. Recently, because of longwall mining and other factors, the capacity requirements of most mine conveying systems have risen substantially; as a result, efficient capacity design and control have become important mine planning issues. This paper reviews these design issues and their associated modeling procedures. Design considerations and modeling difficulties are also examined.

Jan 1, 1996

By Rameshwar Sah, PK GHORUI, LR SINGH, SIVALINGARAJU BARISETTY, SHYAM YADAV

Fly ash is a by-product generated by the combustion of coal in thermal power plants. Its disposal is a major environmental concern for these power plants. Though a considerable part of fly ash is used in cement making and brick manufacturing, a substantial quantity remains unutilized. Bentonite is commonly used as binder in the micropelletization of process waste to attain the mechanical strength required for handling and transportation. The present paper deals with the partial replacement of bentonite with fly ash in the micropelletization process without affecting the quality of the micropellets. The mechanisms of both the binders are discussed. The bonding of particles by bentonite is a physical mechanism, while fly-ash bonding is a chemical mechanism. Silica and alumina are the major constituents present in fly ash along with lime. In the presence of water, the alumino-silicates and unhydrated lime present in fly ash undergo a pozzolanic reaction and form cementitious bonds, which hold the particles together. Use of fly ash as alternative binder for bentonite has cost benefits besides providing a better utilization option for fly ash.

By N. Duru, C. Nesbitt

During the cyanide leaching process, gold and silver ores that come from the transition zones, which typically contains low levels of sulfide, may produce one or more of the following reduced sulfur species: sulfide ( HS−), polysulfides ( Sn 2−), thiocyanate ( SCN−), thiosulfate ( S2O3 2−), trithionate ( S3O6 2−), tetrathionate ( S4O6 2−), pentathionate ( S5O6 2−), hexathionate ( S6O6 2−). The actual speciation of the reduced sulfur species in the circuits will primarily depend on the redox potential, pH, cyanide levels, and existing sulfur species in recycled process water, as well as the presence of other reactive metal species. The development of an accurate analytical method for sulfur species in cyanide leaching units of gold ores where sulfur speciation occurs has an important role in explaining the metal recovery deviations. This study presents the speciation of sulfur species and the development of ion chromatography method to analyze reduced sulfur species thiocyanate ( SCN−), thiosulfate ( S2O3 2−), trithionate ( S3O6 2−), tetrathionate ( S4O6 2−) in cyanide leaching circuits for gold ores. The method developed has resulted in precise quantification of target sulfur species in leach solutions. Method development and validation results were illustrated on analytical graphs containing each species’ peak number, retention time (min), type, width (min), area (mAU*s), height (mAU), and area distribution (%) of the peak.

Mar 2, 2024

By John M. Moore

Within the Pofadder district of Namaqualand, South Africa, economically exploited deposits of bedded barite and zinc-lead-silver-copper sulfides occur in close proximity within highly metamorphosed mid-Proterozoic pre-tectonic para¬gneisses of the Namaqualand Metamorphic Complex (NMC) (figure i). The paragneisses belong to the Bushmanland Group (SACS, 1980) that comprises a relatively straight-forward regional sequence of basal leucogneisses, intermediate mica-sillimanite schists and glassy quartzites, and a mixed upper zone of banded iron formations (BIF), minor marbles, quartz muscovite schists and localised uppermost quartz-pebble conglomerates and amygdaloidal mafic gneisses (Joubert, 1974) (figure ii). The base metal and barite mineralisation occurs in close association with BIFs, generally above the glassy quartzites, although in some cases possibly below them. In the regional context, the Bushmanland Group paragneisses are, to the north, intercalated with and ultimately replaced by meta-volcanic sequences of talc-alkaline affinity (Reid, 1977) belonging to the Orange River Group (SACS, 1980). The metavolcanics are generally of acidic to intermediate composition and show evidence of subaerial formation from 'high altitude shield volcanism' with many acidic ashflow and welded tuff bands, mesocratic and lesser melanocratic lavas and some fanglomerates (Ritter, 1980). To the south and east, the schist/quartzite associations are initially intercalated with and eventually replaced by cordierite gneiss/metacarbonate/biotite gneiss associations of shallow marine affinity (Moore, 1980a). The Bushmanland Group paragneisses appear to represent sedimentary material in the extreme distal portions of a talc-alkaline volcanic environment adjacent to a shallow platform sea.

Jan 1, 1983

By William Gleason

There was a time, not too long ago, when the most daunting challenges facing those in the mining and mineral processing industries could be solved through better technologies and better practices. But now the challenges that come from the actual acts of mining and processing are just part of the bigger picture. SME?s Colorado Section of the Mineral Processing Division (MPD) hosted its 63rd annual meeting at the Broadmoor Hotel in Colorado Springs, April 25-27 and, while the conference had its fair share or mineralolgy and processing presentations that were heavy on the technical side of things, this year?s conference was also focused on the issues of permitting, regulation compliance and legislative issues. The so-called ?softer? issues, that, if not addressed, can lead to very real and very hard challenges. Under the theme ?Mine your own business - permits, startups, expansions and resources,? even the most dedicated metallurgists were drawn into the discussions of politics and legislation, and how those issues affect their business. Fittingly, Colorado Mining Association (CMA) president Stuart Sanderson was honored with the Arthur C. Daman Lifetime Achievement Award. Sanderson, an outspoken proponent for the mining industry in Colorado and beyond, also presented the keynote address to the lunch crowd where he spoke about framing public opinion toward mining and the efforts of the CMA to move the public opinion dial in a direction more favorable to mining. Sanderson explained that Colorado, once a Republican stronghold, turned after 2002 and now is controlled by Democrats who are traditionally less supportive of the mining industry. Sanderson said the deciding factor in the power shift was money, as supporters of Democrats outspent Republicans in the most recent election cycles. CMA has done its part to keep mining going in the state with a broad marketing campaign that was outlined by Sanderson.

Aug 1, 2013

By H. Russell, N. DePriest, J. D. Quaranta

Valley-fill structures built of blasted rock overburden from Appalachian mountaintop surface mines pose many reclamation challenges. The steep mountainous terrain, short valley lengths, and straight stream channel profiles create significant challenges to implementing fluvial geomorphic landform design in terms of both form and function, and from a safety and constructability perspective. The fluvial geomorphic landform design approach balances erosive and resistive forces by considering long-term climatic conditions, soil types, slope profiles and vegetation types. Commercial geomorphic landform design software tools do not specifically analyze the stability and factor of safety for the computer-designed landform slopes. This research investigated slope stability parameters and factors of safety between a traditional valley-fill design with a geomorphic landform alternative. Slope stability assessments were performed on two profile geometries. Finite-element modeling of a permitted valley-fill and a geomorphic design alternative indicated that slope angle and internal angles of friction associated with the gradation of the overburden greatly affected the designed factor of safety for both designs. The geomorphic designed slopes yielded the highest factors of safety out of 14 models analyzed with all cases having factors of safety over 2.0. The high factors of safety are attributed to shallow slopes and beneficial surface and internal drainage.

Jan 1, 2014

By I. R. M. Chaston

Abstract. This paper puts forward the concept of 'radial' plant layout where all crushing, milling and treatment operations are preferably concentrated in one central area and these separate stages are connected by radiating conveyors to and from outside storage areas. This system is contrasted to the more customary system of 'linear' plant layout where the crushing, milling and often the treatment operations follow one after the other in separate buildings. The radial system simplifies and improves contral and supervision to a very considerable extent and can lead to a form of continuous plant operation with the separate sectors shutting down in succession for necessary maintenance while maintaining the overall plant operation. The paper is illustrated with example: from past and recent diamond treatment plant practice in South Africa which demonstrate the reduction in plant labour achieved by this system. Previous objection to this type of layout on the grounds that it inhibited plant expansion are shown to be unwarranted. Radial Layout for Increased Treatment Plant Productivity A great deal of time and trouble is spent by highly qualified and experience( metallurgists in developing the right treatment process for a given ore. This process is then often expressed in a treatment flowsheet of the type shown in Fig. 1 which shows a typical diamond plant. This flowsheet, when completed, is commonly handed over to the mechanical engineers who then design the layout of the equipment indicated on the flowsheet and produce the working drawings upon which the detailed construction of the treatment plant will be based. It is an unfortunate fact that the tedious and time-consuming juggling of equipment and inter-plant transportation is often left to hard-working draughtsmen who, however capable' in their field, lack practical experience in the day-to-day operation and maintenance of the treatment plants they design. As a result many plants have been produced which, while they satisfy the requirements of the flowsheet with minimum capital requirements, cost far more than should be necessary to op¬erate and maintain. It is often possible to change individual items of equipment which do not achieve the performance required of them, but it is usually extremely expensive to change the basic layout of the plant if this should be found to be unsatisfactory. It should therefore be recognised that great care and attention should be spent on consideration of the basic layout of any treatment plant and that the views of both designers and operators should be fully regarded before settling upon the inevitable compromise dictated by the varying requirements of process-engineering and economics. It is unfortunate that this important subject receives such scant regard in the standard ore dressing text books and hand-books, being usually dismissed in a few paragraphs.

Jan 1, 1977

By R. G. Bradburn

The events which led to computer control of the grinding circuit at Brenda Mines are described, beginning with mill operating philosophy. High production rates are encouraged so that, despite severe upstream disturbances, a manual control method to meet this philosophy had developed. Unfortunately, due to the time interval between manual control adjustments, losses in production resulted. An analog control method was devised and, although superior to manual control in some situations, was found to suffer from several practical limitations. The data logging capabilities of a control computer seemed warranted. Circuit test- work combined with an analysis of operating data showed that (1) metallurgical personnel, at times could increase production rates by as much as 10 percent over that achieved by grinding operators, (2) the chosen data base required an increase of 2 percent or more to be statistically significant and (3) for a 2 percent increase there would be a significant rate of return of investment in a computer installation, Consequently one grinding circuit was fully instrumented, and a rented control computer was installed by Brenda personnel. Prior to installation, Brenda metallurgical and instrumentation personnel were trained in the use of the computer. An experimental program was devised with short and long term objectives. The short term objective was to develop a practical control strategy which would yield immediate production improvement. This goal has been met as described in this paper. Statistically significant increases in excess of 2 percent have been established. Work is being completed for the permanent installation of computer control on all four grinding circuits at the present time. Long term objectives are (1) off line analysis of the circuit using mathematical models of process units, (2) on line experiments to study alternative contol tactics, and (3) possible expansion of computer facilities to the crushing plant.

Jan 1, 1976

By O. J. Malacarne

The use of a series of thickeners for-washing of the slime fraction of a leached ore is not uncommon in the uranium industry; however, few ore processing mills have used a thickener circuit for washing leached total ore. The, common, practice is to wash the sand fraction in classifiers and, the slime fraction only in thickeners. At the Uravan mill of Union Carbide Nuclear, Company, a total ore' acid leach is employed to extract uranium values from sandstone ores. These leached ores are then washed at a nominal rate of from 1,000 to 1,300 tons per day in a series of washing thickeners. A typical screen. analysis of the ore being washed in these thickeners, is 25 percent -200 mesh, 3 percent +35 mesh and about, one' percent +l4 mesh., The amount of slimes (-200 mesh) will vary from 20 to 30 percent s the mill receives ore from 150 different mines The washing liquor is acidic, from a pH of about 2 in the first thickener to 0.6 pH in the last thickener and of course ally acid duty equipment must be used. The Uravan mill of Union Carbide Nuclear Company is located in Montrose County, Colorado and is physically located on a canyon wall along the San Miguel river. The thickeners referred to in this, paper are located on top of the mesa above the canyon. For purposes of identification, these thickeners are numbered 1 through 8 from south to north.

Jan 1, 1962

By Felicia F. Peng

An economic analysis for evaluating coal preparation plants in the Appalachian Region is presented. A complete coal preparation plant which includes multi-streams and/or multi-stages coal cleaning circuits, complete closed water circuits, environmentally acceptable refuse disposal and reclamation systems is used to determine the capital and operating costs. The plant is capable of producing metallurgical grade clean coal or deep cleaned steam grade coal for future power generating plants use. Utilizing a profit maximization as a decision criterion, an optimal yield, and optimal coal clean¬ing circuits, closed water circuits, and disposal and reclamation systems for a given coal characteristic may be selected among the process alternatives by using a process simulation-economic model of the coal preparation plant. A deterministic analysis is used to calculate the discounted-cash-flow interest rate of return (DCFIROR) and project the selling prices, and determine the Return on Investment (ROI) for the cases of 32.65% and 52.74% plant utilization with producing two cleaned products. Sensitivity analyses are performed to quantify the effect of total capital investment, operating cost, run-of-mine cost and yield on an economic criterion-ROI and selling prices. A probabilistic evaluation using the Monte Carlo simulation technique is further made to quantify the risk involved in obtaining the desired profit levels. The results of the economic analysis for a given coal preparation plant configuration and characteristics of raw coal indicates that the selling prices of producing two cleaned products are greatly affected by the change in percent of plant utilization (production schedule), yield, and run-of-mine cost, and total capital cost. The sensitivity analysis also shows that the total capital investments has a three times greater effect on required selling prices than operating costs. The risk analysis shown that the overall economics look very attractive with current coal sale prices and 52.74% plant utilization.

Jan 1, 1979