Search Documents

By Khosrow Badiozamani

Operating mines in Wyoming and Montana, which are generally characterized by shallow overburden and thick coal seams, are faced with reclamation problems which are unique to this area. Unlike the eastern or midwestern mines, removal of thick coal seams and lack of sufficient overburden creates overburden deficiencies that require careful evaluation prior to mining to insure compliance with regulatory requirements. Computer models and computer graphics can assist in such evaluation where appropriate alternatives can be selected which satisfies both the regulatory requirements and minimizes cost. This paper presents one such model used in evaluation of backfill requirements for restoration of surface and ground water regimes, restoration of mined-out areas to the approximate original contour, and the blending of the mined-out areas to the surrounding topography.

Jan 1, 1981

By G. S. Dobby

Particle collection is considered to occur by particle collision with the bubble followed by the particle sliding over the bubble during which attachment may occur. Collision is quantified by a collision efficiency, EC. The existing model for EC is extended by including particle inertia. Attachment is quantified by an attachment efficiency, EA calculated as the fraction of particles which reside on the bubble for a time greater than the induction time. These calculations use recent data on the liquid velocity distribution over the upper half of rigid spheres. Collection efficiency, EK is given by EK = EC ? EA. Detachment is not considered. The mode is examined and shown to agree with much experimental data. For example the maximum observed in recovery vs particle size (d) can be explained as E increases with increasing d , while EA decreases. The decrease in selectivity at fine sizes is in accord with the model result that for dp < 5µm, EA ? 100% (i.e. EK ? EC) almost regardless of induction time. A decrease in bubble size does increase EK but does not improve selectivity. A high particle density (> 5g/cm3) is shown to cause a sharp peak in recovery vs size and a decreased maximum size of floatability. Finally, the possible effects of bubble and particle concentration are explored.

Jan 1, 1985

By Bo R. Arvidson

The strongest magnetic roll separator available on the market enhances certain industrial minerals purity to levels not reached previously. Exceptionally strong forces can also be utilized for processing relatively fine particles at feed rates several times greater than for prior art electromagnetic induced roll separators. Since the unique machine does not work with an air-gap, coarser particles than what has been considered practical can be separated at rates up to 20 tph per single machine unit and 40 tph for a double machine unit. Examples for all these three application areas will be given. While the roll separator can be used only for dry processing presently, the other new separator can be used for both wet and dry applications. It is a medium-intensity, high- gradient magnetic separator employing a filamentary matrix. It was primarily developed for recovery of weakly magnetic iron ore fines, but it is finding applications for cleaning of industrial minerals such as wollastonite, calcite, clay and talc. Its main advantage is a simple design resulting in a very lm cost machine both with regards to total capital investment and operation. A significant technical advantage exists also. The metallurgical performance is similar to conventional electromagnetic separators, while the cost per ton is about half of such separators.

Jan 1, 1985

By Farzad Moradpouri, Kianoush Barani, M. R. Azadi

The aim of this paper is to assess the effect of microwave treatment on copper sulfide ore for ball milling and bed breakage. Liberation analysis of ground products in eight size fractions showed that microwave pretreatment liberated more chalcopyrite particles from the bed breakage product than the ball mill product. In bed breakage, microwave pretreatment caused a 2% increase in chalcopyrite liberation on average. Microwave pretreatment produces more elongated particles in ball milling and more rounded particles in bed breakage, respectively. Microwave pretreatment produces coarser chalcopyrite particles with a wide range of sizes. This effect is more significant in bed breakage compared with ball milling. Micro-flotation test results showed that in ball milling, treated and untreated materials have similar metallurgical performance and there is a little difference (1%) between the average Cu recovery values. However, in bed breakage, the average recovery for the treated materials is about 5% higher than the untreated materials.

Jul 8, 2021

By Soner Top

In this study, a process to separate manganese and iron from manganiferous iron ores by reductive acid leaching followed by magnetic separation was conceived and experimentally tested. In the leaching process, sulfuric acid was used as lixiviant and oxalic acid was used as reductant. The experimental results showed that the manganese and iron separation was optimum when the concentration of the sulfuric acid and oxalic acid were 0.75 M and 30 g/L, respectively, at a temperature of 80 °C, a solid/ liquid ratio of 67 g/L, stirring speed of 400 rpm, and leaching duration of 60 min. Under this condition, 90.49% and 6.78% of Mn and Fe were dissolved, respectively, from the ore sample with a size fraction of − 106 μm. It was determined that the leaching of manganese from the ores was a second-order reaction with an activation energy (Ea) of 53.38 kJ/mol. The leaching residues obtained under the optimum condition were subjected to high-intensity wet magnetic separation tests to recover the remaining iron content. This separation process produced a concentrate containing 56.20% Fe and 1.79% Mn with iron and manganese recoveries of 56.83% and 66.73%, respectively. A magnetic separation test from an unleached ore sample was also carried out as a benchmark. To the best of our knowledge, this is the first time that a magnetic separation process was used to a residue obtained from reductive acid leaching of manganiferous iron ores to recover iron.

By Florence Ntsiful, Eric Stemn

Exposure to whole-body vibration has been recognised as an occupational hazard in the mining industry, especially in the operations of earthmoving equipment. Managing whole-body vibration exposures requires periodic measurement of exposure levels to identify priority areas for implementing controls. However, due to different approaches to collecting exposure values, significant variabilities lie in the results. This systematic review is the first attempt to analyse whole-body assessment methods in the mining industry. The aim was to identify how whole-body vibration has been assessed, including the sources of variabilities to improve future research. The PRISMA methodology was adopted for the review and a total of 152 peer-reviewed journal articles were identified. However, only 24 were included in the review, following the application of some inclusion criteria. Descriptive and thematic analyses were performed on the 24 selected articles. Results indicate that whole-body vibration has been assessed as a function of either equipment characteristics, activity undertaken, operator characteristics, measurement approach or the assessment standards. Due to the multifactorial and dynamic nature of wholebody vibration exposures, the variabilities in results are due to the interrelationships between the risk factors of whole-body vibration and the differences in the sample sizes. To identify the sources of variabilities, a comprehensive assessment of all the risk factors, including equipment characteristics, road conditions, operator characteristics, and activity undertaken, is highly warranted. Finally, research gaps and directions for future research have also been discussed.

Dec 21, 2022

By G. W. McCaa

Plans for a large industrial development in the Upper Ohio Valley between Moundsville and New Martinsville, West Virginia, were announced in the Fall of 1955. This development consisted of a large aluminum plant to be .built by Olin-Mathieson; a 675,000 KW power plant to be constructed by the American Electric Power Service; and a large coal mine adjacent to the power plant to be developed by the Hanna Coal Company Division of Consolidation Coal Company. The Ireland Mine was designed to efficiently supply fuel for the power plant, and this was the first consideration in the location of facilities, design, and development of plant and the selection of the equipment. The first problem was to find a suitable area for the surface facilities. A level bottom area south of the power plant was reserved for future industrial plants and this area was also blocked off from the coal reserves by an old abandoned and flooded mine. The coal storage facilities of the power plant were on the north side of the plant and it was decided to locate the coal mine preparation plant on-the shoulder of a hill above the power plant. This location required the excavation of 70,000 yards of rock but permitted the driving of a belt slope from the plant at an angle so that the haulage roads underground would miss the abandoned Cresap Mine. This location also permitted the plant to be located at an elevation so that the conveyors leaving the plant were horizontal and had sufficient clearance above the highway and railroad tracks. The other surface facilities consisting of air shafts, supply slope, supply yard, office, bathhouse, shop and warehouse were located in the valley some distance north of the preparation plant. This location placed these facilities one mile nearer to the working area. Plans for design and development of the mine were started in November 1955; grading and clearing of surface area was started in January 1956; the air shafts and slopes were started in the Spring and Summer of 1956; and the first coal was produced from the supply slope in October 1956. The preparation plant was put in operation in March 1958, and by July 1959 was producing 8,000 tons per day.

Jan 1, 1959

By Josh Willhite, Seth Pollak, Ben Seling

The Long Baseline Neutrino Facility Far Site at the Sanford Underground Research Facility in Lead, South Dakota will house four large detector tanks located in deep underground caverns. Construction of the supporting infrastructure required for this project is no complete including installation of a waste rock conveyance system and drill and blast excavation of several supporting drifts and chambers. This paper will discuss the design and construction of these pre-excavation and early works elements, and the overall project schedule as it closes in on commencement of cavern excavation activities.

Jun 13, 2021

By M. Allan Holtz

The shipment of coal, ores, and minerals in bulk form during the winter months presents a difficult problem in emptying rail cars. U. S. Steel Research in cooperation with U. S. Steel Coal Operations bas laboratory tested and field monitored the effectiveness of using freeze conditioning agents (FCA) to minimize the frozen coal problem. This report examines, in an overview manner, our experience after four seasons of treatment using different FCA agents on raw and preparation plant products. Our observations indicate that if an FCA is applied correctly it is effective mineral to mineral. Freezing problems still occur at the interface between the coal and the metal of the car sides and bottoms. Leading chemical suppliers have made positive improvements in their FCA formulations with second and third generation products. Further advances are needed to make chemical treatment for the prevention of frozen coal a real full-proof method.

Jan 1, 1980

By Robert J. Willard

In its search for additional ways to increase understanding of rock behavior, the Twin Cities Mining Research Center has turned to the scanning electron microscope, an instrument rapidly finding application in research concerned with surfaces of materials. Since features indicative of the manner in which rocks fail may be recorded on the surfaces of fragments as disintegration proceeds, this microscope might be used as a tool for seeking and mapping these minute features. In pursuit of such features, we chose to scan a portion of the fracture surface from a quartzite disk compressively loaded to failure between two pins centered along the disk&apos;s axis. The resultant fracture appeared as a rough, diametric plane, and the fracture surface near one of the loading points was scanned with the microscope.

Jan 1, 1969

By Billy W. Parks

This paper reports on the first 2 years in operation of a special-purpose coal handling rig which provides blending, temperature reduction, and continuous, automatic mechanical sampling as part of midstream barge to ship coal transfers. Briefly reviewing some of the characteristics of coal handling peculiar to midstream transfers, the paper discusses how the most beneficial aspects of midstreaming were enhanced through the design of this blending and sampling rig.

Jan 1, 1986

By Francisco J. Sotillo

Using new ecological-natural-organic depressant for gangue and pyrite with antibacterial properties (control of acid mine drainage) with new improved xanthate collectors using rheology additive not chemical reacting with xanthate resulted in better sulfide flotation. Rougher-scavenger lead flotation tests were conducted increasing the concentrate grade from 7.07% Pb to 13.44% Pb, enhancing selectivity. Lead recovery increased from 64.08% to 79.38% and 80.40% using only the new depressant, and improved xanthate Z-11 and Z-4, respectively. The results demonstrated that the new depressant was selective and efficient, and the new improved xanthates stronger more selective collectors.

Feb 22, 2026

By D. Seneviratne

Iron transfer from the pregnant leach solution (PLS) to the electrolyte can have a major economic impact on solvent extraction (SX) operations. High iron transfer will lead to greater operational costs, due to increased reagent consumption through electrolyte bleed and make up, or increased power costs due to decreased electrowinning current efficiency. Bioleaching of low-grade copper sulfide ore from the Kennecott Utah Copper Mine was investigated in a large scale piloting program including SX and electrowinning. Plant data and lab test work conducted throughout the course of operation, show that the unique containing PLS high ferric iron with high pH can lead to lower Cu: Fe selectivity than is typically seen in traditional copper SX operations. The impact of high ferric iron on the plant operation, and methods to reduce iron transfer will be discussed. Special considerations need to be taken for plant operating conditions and selection of SX reagents (including both extractant and aromatic content of diluent) based on the feed PLS characteristics.

Feb 23, 2014

By A. M. McKim

6, 7.3 meter diameter autogenous mills at Wabush Mines are undergoing conversion from a radial configuration of pulp discharger to a curved design. Improved discharging efficiency has effectively lowered the pulp level in the mill. The low level operation enhances the grinding efficiency netting a 12% power reduction. Significant reductions to rate of wear has been a spin off benefit. The design incorporates features for holding the assembly solidly in place thus eliminating bolt hole damage and leakers. Preliminary work in one 11 meter mill at Hibbing Taconite did not indicate that all the same advantages were available in their process.

Jan 1, 1982

By C. R. McClung

"Molybdenum, in the form of molybdenite, is a common byproduct of many copper mining and concentrating operations. Contrary to most copper sulfide minerals where recovery is principally liberation controlled, the recovery of molybdenite is much more complex with fully liberated particles commonly lost to tailings. It is this complexity that facilitated the necessity for a geometallurgical investigation of molybdenite from the Bingham Canyon deposit. The aim of this investigation was to determine the effect mineralogy and/or mineralogical attributes (i.e. morphology, angularity, liberation, size) have on the recovery of molybdenite in the processing circuit. A set of samples was collected from the ores and products produced by Rio Tinto Kennecott’s Copperton Concentrator. All samples were analyzed using normal polarized reflective light, Mineral Liberation Analyzer (MLA) and X-ray diffractometery (XRD) techniques. The results of this investigation revealed the presence of two distinctly different types of molybdenite, which have been identified as the two polytypes of molybdenite, i.e. hexagonal (2H) and rhombohedral (3R). The 2H polytype occurs as textbook-shaped particles in quartz-molybdenite veins that are located in the core of the Bingham Canyon deposit. The 3R polytype occurs as disseminated, “ball”-shaped particles with a dull or frosted appearance along the margins of the mineralized intrusive body or central core. Concerning their metallurgical behavior each type exhibits unique metallurgical properties that are consistent with those reported in the published literature. For instance, the 2H polytype is easily ground and kinetically “faster” floating with surface attributes that are amenable to higher rates of recovery. This commonly results in the production of a high quality molybdenum concentrate under normal operating conditions common to most copper concentration operations. In contrast, the 3R polytype is difficult to grind and kinetically “slower” floating with surface attributes that less amenable to recovery under normal operating conditions. Therefore, in deposits with higher concentrations of the 3R polytype, modifications to the normal operating parameters may be necessary to improve the recovery of molybdenum. Finally, a preliminary investigation into the metal budget of porphyry Cu and Mo deposits indicates that a positive correlation may exist between the total economic metal budget and the polytype content. For example, higher concentrations of the 3R polytype appear to be more prevalent in Au-enriched porphyries versus Mo-enriched porphyries. This observation may also serve to help explain why it is easier to obtain high rates of recovery in Mo ± W-rich deposits, which contain little to none of the 3R-polytype. Consequently, the potential for the metal budget of a porphyry deposit to be used as an indication of the molybdenite polytype present, as well as its impact on the economics (exploration) and/or on the processing circuit (plant design) could exist. In conclusion, this investigation highlights the necessity of understanding the mineralogical properties or characteristics of molybdenite and/or other economic mineral(s), as these can and will have a direct impact upon the performance and plant optimization."

Jan 1, 2016

By Dongjie Zhang, Shuxin Liu, Jianduo Wang

Broken rock mass and unreasonable stope structure parameters can cause excessive ore loss and dilution in sublevel caving; this is the main problem faced by caving mining in recent years. This paper proposes a stope structure parameter optimization method suitable for steeply inclined medium-thick broken ore bodies and evaluates the reliability and effectiveness through case studies. To solve the problem of large ore loss and dilution in the high-end wall sublevel caving method of Xilinhot fluorite mine, it is necessary to select proper stope structure parameters. Based on the theory of random media, an end-wall ore drawing experiment was carried out, and the bulk flow parameters needed to optimization of stope structure parameters were determined. In the experiment, it was found the draw-out body of high-end wall ore drawing showed a fine top and a thick bottom; the granular media had good fluidity. The reasonable caving step is determined to be 1.2 m instead of the 1.6 m originally used. Through the optimization experiment of the mining route position along the vein, the study found that the best route position is different with the ore body inclination. When the inclination angle of the ore body was 90°, the reasonable route was located in the center of the ore body. When the inclination angle of the ore body was between 85° and 90°, the route moved from the center of the ore body to the footwall at a rate of 22.5%. When the inclination angle of the ore body was between 80° and 85°, the route moved to the footwall at a rate of 54.8%. When the inclination angle of the ore body is not greater than 80°, the route should be arranged on the boundary of the footwall. Field application results showed the dilution rate reduced by 7.66% and the recovery rate increased by 7.31%. Field test results verify the effectiveness and applicability of the optimized stope structure, which corroborates the effectiveness and applicability of the optimized stope structure.

Mar 10, 2022

By W. D. G. Hunter

Since 1945 the world&apos;s iron ore industry has experienced radical change. This transformation is reflected in new levels of production, consumption and trade, in shits in the location and size of markets, in the tapping of far distant sources of iron ore, and in the emergence of new export centres catering on an increasing scale to ore deficient, importing countries. Within the broad framework of shifting supply/demand relationships, certain operationally meaningful adjustments can be singled out for special mention: 1. The iron and steel industry has undergone vigorous and aggressive expansion, during the post-war period, not only in the capitalist world and among the socialist bloc, but in backward regions as well. New countries have been added to the list of steel producers, while new facilities have been relocated by established steel makers. 2. Overall demand for iron ore has risen rapidly, arid has flowed different channels.

Jan 1, 1964

By Jonas Svensson

The Grangcold Pellet Process - for which patents have been applied or already granted in a number of countries - uses a hydraulic adhesive such as Portland cement, slag cements, pozzolanic cements, etc., for the production of cold bonded pellets. The idea of using a hydraulic binder for the agglomeration of iron ore fines is not new. Portland cement was proposed as an adhesive for cold bonded iron ore briquettes in patents granted more than 50 years ago (1). In a report on the briquetting of iron ore fines, published in Stahl and Eisen 1959 (2), it is stated that briquettes bonded with Portland cement are used on a small scale at on ironwork in Germany. According to the report, the briquettes showed excellent strength in the blast furnace although their general use was made impossible because they required a long hardening time, during which they are sticky, soft and difficult to store and handle. The Grangcold Pellet "recess has overcome this particular disadvantage by mixing the balls with a suitable amount of the balling concentrate before storing them. The pellets are embedded in the concentrate during storing in such a way that they are isolated from each other and thus prevented from sticking together to form clusters. Thanks to the embedding concentrate, the pellets are subjected to a more or less uniform pressure from all sides which does not deform them. Thus the mixture can he stored in a stockpile or in a silo until the pellets have hardened sufficiently. The concentrate is separated from the pellets by means of screening. The concentrate is returned to the balling operation and the pellets are either shipped to the blast furnace or stored for final hardening.

Jan 1, 1969

By Edwin H. McKee

Eruption of rhyolitic ash-flow tuffs in the area of the McDermitt (Cordero) caldera began about 17.4 m.y. ago and continued for about 1.5 m.y. During this period of silicic eruptions, a circular area about 30 km in diameter collapsed to form a caldera that subsequently filled with sedimentary and volcanic rocks. 3 A total of more than 200 km of silicic rocks was erupted from the volcano. The final phase of igneous activity, about 15.5 m.y. ago, included resurgent doming and intrusion in the central part of the caldera. Three to 4 m.y. later +I2 m.y. ago), hydrothermal solutions using the northern part of the caldera ring fractures as conduits deposited cinnabar, pyrite, alunite, and other minerals in tuffaceous lake beds and volcanic rocks accumulated within the caldera. The ore-forming solutions may have been a residuum from the silicic magma or connate water or ground water heated by the still-hot resurgent magma in the central part of the caldera. The source of the mercury has not been identified. Later oxidation of the sulfide minerals and redistribution of the supergene minerals corderoite, several mercury nitro-oxychlorides, marcasite, iron, and titanium oxides in the sedimentary rocks account for most of the newly discovered ore body at Cordero.

Jan 1, 1976

By T. Fernandez, V. Juchen, C. Petter, F. Cantini, V. Lenz, V. I. Araújo, R. Petter, R. Darrigo, A. Young, I. G. da Costa, J. Oppermann

There are many methods to estimate costs quickly. One of these is the Parametric Method, where costs are estimated from general algorithms (or curves). Derived from an original tool based on the O’Hara model, a software called MAFMINE was developed. MAFMINE is based on parametric models to estimate investment and operational costs in mining. The software itself is based on the use of a computer model known as client-server. However, the model needs new inputs from advances made by the mining industry, mainly in terms of electrification, automation, digital transformation and preconcentration to face Environmental, Social and Governance (ESG) concerns. Thus, this work was to prepare a new core module ready to incorporate the new technologies aiming to deliver operation and capital costs associated with environmental impact mitigation. The tool generates an order of magnitude estimate for CAPEX and OPEX to establish a very first Discounted Cash Flow (DCF) in a mining venture. For quick evaluations, at a preliminary level, the results are very promising.

Mar 2, 2022