Search Documents

By Robin Burgess-Limerick

The introduction of automation to mining has great potential to reduce safety and health risks by removing people from hazardous situations. However, automation changes the tasks performed by people and may introduce new tasks. For the system to function optimally, these tasks must be designed taking human abilities and limitations into account. Humansystems integration refers to systems engineering processes that ensure that human-related issues are adequately considered during system planning, design, development, and evaluation. During procurement of automated systems, a human-systems integration program plan should be prepared that describes the human-systems integration activities that will be performed to address each of the six core domains of human-systems integration: staffing, personnel, training, human factors engineering, safety, and health.

Jun 16, 2020

By Nagashi Ogushi

Geochemical prospecting method using stream sediments, soils and rock chips has been tested to see the applicability for the typical Kuroko field in Japan. Three independent anomalies have been detected in maps being shown by grav densities of cells which are represented by the results of factor analysis as well as distribution of minor elements scaled in logarithm. A small vein type mineralization which has outcrops could be attributed to the origin of them whereas the one near the surface of known Kuroko deposit to a coincidence. The addition of drill core geochemistry is required to complete the interpretation.

Jan 1, 1982

By R. Bissonette, C. Sunderman, R. Jacksha

The ability of wireless systems—e.g., voice communication, proximity detection, tele-remote operation, telemetry, etc.—to function satisfactorily (coexist) in the presence of other wireless systems is critical to the safety and health of mine workers. The failure of wireless systems to coexist could result in the delay, corruption, or outright loss, of critical data, voice, or video information. However, no mining-sector-specific regulations, standards, or guidelines exist to ensure the safe coexistence of wireless systems. This paper introduces the concept of wireless coexistence, implications in the mining industry, and the National Institute for Occupational Safety and Health’s (NIOSH’s) research approach to develop guidelines and recommendations to ensure safe wireless coexistence.

Feb 1, 2023

By J. J. McClellenand, R. A. Jankowski

Face ventilation and water sprays are the primary controls used on continuous miner sections to protect workers from respirable coal and silica (quartz) dust. Laboratory tests were conducted by the U.S. Bureau of Mines to determine the impact on respirable dust concentrations when increasing airflow from 3000 to 9000 cfm (1.42 to 4.25 m3/sec), water flow from 15 to 35 gpm (0.057 to 0.132 m3/min) , and water pressure from 80 to 200 psi (5.52 x105 to 1.38 x106 pa). The effective limits for each control and interactions between these controls were of particular interest. Initial analysis concentrated on defining the impact of the control parameters on the respirable fraction of the feed dust, which was a blend containing 90% coal and 10% quartz. Gravimetric sampling indicated that airflow had the most significant individual impact on respirable dust levels and resulted in reductions of 99% at the operator and 57% in the return. Regression modeling was used to predict dust concentrations at the operator and in the return. Significant interactions were observed between control parameters and often, defined the level for a control parameter where increases above that level did not significantly benefit dust control. Increasing airflow to 8400 cfm (3.96 m3/sec), water flow to 25 gpm (0.095 m3/min), and water pressure to 140 psi (9.65 x105 Pa) typically provided respirable dust reductions at both sampling locations, while optimizing use of control resources. After determining these relationships for the total respirable fraction, selected filters were analyzed for quartz content to define the impact on the quartz component of the feed dust. For the individual control parameters, airflow again had the most significant impact and resulted in reductions of 98% at the operator and 26% in the return. Regression modeling of the quartz concentrations indicated that no significant interactions between control parameters were present. At the operators location, airflow was the only parameter identified as having a statistically significant reduction for quartz dust. A reduction in quartz approaching 95% was observed for increasing airflow to 6000 cfm (2.83 m3/sec). Increases above 6000 cfm had little additional impact. In the return, a linear relationship between control parameters and quartz levels was observed with reductions of approximately 27% predicted for increasing any one control parameter to its maximum level. The synergistic impact of increasing all control parameters to maximum levels resulted in a maximum predicted reduction of 81%.

Jan 1, 1991

By Carl E. Williams

During the past two years a computer program called "COPOR," Computerized Open Pit Optimization Routine, has been developed and used for mine planning of several base metal deposits. This routine utilizes a three dimensional computerized block model of an orebody, some economic parameters and operating constraints to locate the mineable or economic limits of the deposit schedule the yearly production from the mine and produce bench by bench ore reserve summaries and maps of the yearly and ultimate pit configurations. The moving cone method is used to perform these functions with a conventional block model. This model is conventional in the sense that each block is assumed to be homogenous; i.e., either ore or waste but not a mixture of the two. Due to the nature of a seam type deposit this approach is not realistic; therefore, revisions have been made to form a new version of the COPOR program. This version has been named "COALOR," Coal Optimization Routine. COALOR contains all of the power of the COPOR program but is equipped to handle the intricacies of coal seam type deposits. The deposit can be composed of a single seam or multiple seams which are horizontal or dipping at any angle. The numerous coal quality values can be incorporated to aid the optimization of the economic pit limits and yearly scheduling.

Jan 1, 1978

By D. D. Xu

A novel system for the depression of pyrite and the ash-forming minerals has been developed. A metal ion, including but not restricted to Fe+2, is added to form a hydroxide coating on the pyrite or ash-forming mineral. A polymeric depressant is then added to attach to this re-surfaced mineral. Nearly 200 flotation tests with a 11 different coals indicate the effectiveness of this system. Many of the important process variables such as the coal source, frother-collector system, grind size and procedure, pH, metal ion, and depressant type and concentration have been studied.

Jan 1, 1994

By N. O. Lotter

Studies investigating the evaluation errors in laboratory scale flotation tests for platinum-bearing Merensky Reef in the Bushveld Complex, South Africa, have constructed a quality control model to assure a 95% confidence in the attested data. Specialized knowledge of the mineralogy of the platinum-group elements (PGE), together with acquaintance of evaluation models, validate a systematic checking of the sub-processes of the testwork. These include determination of minimum mill feed sample size, assay head reference distribution, mass balance checks, and specialized sample preparation of flotation test products prior to analysis. A flow schematic of this quality control model is proposed, with an example of test data that produce an error in the metal balance of 0,2% after rejection of outlier data.

Jan 1, 1995

By Chester O. Ensign

The White Pine Mine is situated in the southwestern portion of the Keweenaw Peninsula of Upper Michigan approximately 6 miles south of Lake Superior (Fig. 1). It is east of the Porcupine Mountains in Ontonagon County. The ore deposit is about 70 miles southwest of the famous native copper deposits of the "Copper Country" lying northeast of Houghton. Geological conditions are different at every mine and create a special set of problems in dilution control. This paper is largely intended to describe the techniques applied in mine dilution control (grade control) at White Pine, and present results of the program. For necessary background information major geologic characteristics of the deposit, particularly those that exert control over the distribution of ore, are briefly discussed. Mining methods are described in considerable detail since applied grade control techniques are adapted to these.

Jan 1, 1964

By G. W. Cutting

Interlocking material balances on complex mineral dressing plants greatly assist in metallurgical investigations: indeed, without such a balance, there is no firm basis upon which to base process performance evaluations. To achieve balances both qualitative and quantitative data must be rationalised in conjunction with the process flowsheet. WSL has developed a range of programs to evaluate interlocking material balances. However, to obtain maximum benefit from the balances, answers of direct value at the process level must be provided: WSL has developed also a range of programs for this purpose. Practical examples are given, which illustrate the benefits obtained from process balances.

Jan 1, 1979

By G. Robson

"From monitoring gas levels and air quality in coal mines to protection from collisions for large vehicles at mine sites, SICK offers a wide range of sensors and systems to improve safety and to monitor potentially dangerous situations. SICK offers solutions for the analysis and monitoring of underground coal mining atmospheres. These systems supply the coal mine operator valuable safety and ventilation information, as well as data which identify and monitors atmospheres of those production areas within the mine which may or may not be worked, such as Goafs and sealed areas. Underground coal mines contain dangerous gases, which must be monitored and controlled in order to allow productive mining operations to take place and to minimize the risk of explosion. Underground mines are a potentially dangerous place for mine workers. These are the main reasons for using Tube bundle systems SICK has had great success in selling these systems into the Australian and New Zealand Markets and this is helped by the strong drive for mine safety from both the Mine Owners and the Regulatory bodies charged with the responsibility of ensuring Mine Regulations are met. The Australian mining industry uses Tube Bundle Systems at almost all underground sites, even after mining has ceases and the mine is placed in care and maintenance. Sick has been working in international markets for some time now but has had limited success in selling Tube bundle Systems to these markets. However in recent times there has been raised interest in Tube Bundle from China, India and Turkey as these countries strive to improve mine productivity and lessen the risk of explosion or Spontaneous Combustion. Our lack of penetration into International Coal markets has been very much based on the perceived cost of the system, not the benefits to safety and productivity. Unless a mine has had an event such as spon com or a Methane explosion they rarely consider the very low level measurement capability (20 PPM CO & 100 PPM CH4) or the long term trending benefits of the Tube Bundle system. It is only after a catastrophic event the System is considered. Real Time or electrochemical Sensors are commonly used to monitor the Mine Atmosphere, the real problems of methane build up or potential Spon Com in Goafs and sealed areas cannot be monitored using Real Time Sensors as the electrochemical cell deteriorates after approx. 12 months and in sealed areas these cells cannot be maintained or replaced. Whilst the Technique of Tube Bundle Systems is quite old SICK have spent many years redesigning the Tube Bundle System into a cost effective and real value for money product. The system uses state of the art sampling and highly accurate Infra-Red wide Spectrum Analysers."

Jan 1, 2016

By İbrahim Çınar, Hakan Özşen

Mine workers in heavy and dangerous work are under several physical risk factors, for example temperature, humidity, noise, vibration, lighting and air velocity. Thermal comfort includes parameters such as air temperature, air humidity, air flow rate, radiant heat, metabolic rate and garment insulation. In this study, thermal comfort conditions were evaluated using thermal comfort indices defined as predicted mean vote (PMV) and predicted percentage dissatisfied (PPD) which were determined by measurements taken from an underground coal mine for approximately 100 days. Although the metabolic rate (light work) was kept at 2 met, it was found that predicted mean vote ranged between − 2.58 and 1.68. The predicted percentage dissatisfied index was found to reach 95%. According to the results, it can be seen that thermal comfort may have negative effects on occupational health and safety. The change in thermal comfort index values in the Soma Underground Coal Mine was investigated in detail and the reasons for the changes were determined. Furthermore, determining the optimal working environment for the mine workers was also an aim of this study.

By P. E. Wingrove

The Kayford, Boone and Nicholas Division of Bethlehem Mines Corporation operates a modern coal preparation plant in Van, West Virginia. Since the start-up of the Van Plant in 1976 until the summer of 1980, the refuse handling system proved to be a costly maintenance problem and a material handling bottleneck. During the 1980 two-week miner's vacation the original system, which included two screw conveyors and a drag conveyor, was replaced by an installation utilizing two Flexowall steep angle belt conveyors. This paper describes the technical and economic analysis that led to the new installation and reviews its first year operating performance. The Van facility is a heavy media plant designed to handle 127 mm x 0 raw metallurgical quality coal from the Powellton seam at a maximum feed rate of 590 TPH (metric tons per hour). Depending on mining conditions, the clean coal recovery rate averages between 50 and 65%. The plant is set up with three types of cleaning circuits. Coarse material (127 mm x 12 mm) is cleaned in heavy media baths. Intermediate size material (12 mm x .5 mm) is cleaned in heavy media cyclones. Fine coal (.5 mm x 0) is cleaned in a hydrocyclone1 froth flotation circuit.

Jan 1, 1981

By Wen H. Su

This paper examines the intrinsic mechanisms of cutter roof by combining field investigation, laboratory testings, underground instrumentations, and numerical modelling. Cutter roof developed during the development of a set of longwall panel entries in a West Virginia coal mine was presented as a case study. Mining alternatives applicable to the mine are recommended. Cutter roof occurred in two other West Virginia coal mines were also investigated Detailed comparisons were made among the three cases. As a result of the extensive investigation, intrinsic mechanisms of cutter roof failures under various conditions are presented from the practical and theoretical points of view.

Jan 1, 1985

By Konner Horton, Adam L. Bedell, Don Del Nero, Brian Jones

"The City of Atlanta’s Water Supply Program Tunnel project includes a 7,315-m (24,000-ft) long, 4-m (13-ft) diameter, hard rock tunnel. A complex aspect of the project involves connecting five, blind bore shafts to the tunnel in a location close to current drinking water reservoirs. During the supplemental geotechnical investigation following the initial contract award, results from additional borehole geophysics were reviewed. Unfavorably oriented fracture sets forced a change in the original pre-excavation grouting program designed for that site. Real-time grout monitoring and geophysical data were compared to provide assurance that the program, as designed, correlated with the in situ ground conditions. Following grouting, results were modeled, and all grouting data were reviewed to determine if grouting was complete.Project backgroundThe current water supply system operated by the city of Atlanta’s Department of Watershed Management (DWM) consists of four, aged, raw-water pipelines, one of which dates back to 1893. Based on previous assessments completed by the DWM, the entire water supply system is at, or will soon reach, its recommended useful life. As such, the city acquired the Bellwood Quarry in 2006 with the intention to create a water storage facility with a volume of approximately 9.1 billion L (2.4 billion gal) to serve approximately 1.2 million people.The project location is shown in Fig. 1, which is generally in the northwest part of downtown Atlanta, GA. The overall project has been divided into two phases. The Phase 1 project connects the quarry and the Hemphill Water Treatment Plant (HWTP), and the Phase 1 Extension project connects the HWTP to the Chattahoochee Water Treatment Plant (CWTP) and the Chattahoochee River. A 7,315- m (24,000-ft) tunnel with a finished diameter of 3 m (10 ft) connects all three elements. The HWTP location is also where the city’s two most proximate drinking water reservoirs are located."

Jan 9, 2018

By D. K. DeForest

The olfactory system (sense of smell) is crucial to the ability of fish to avoid predators, recognize kin, and synchronize reproduction (Baldwin et al. 2003). Copper (Cu) has been shown to impair olfaction in juvenile freshwater life stages of salmonids (including Pacific salmon and trout) in some laboratory experiments; and in the United States, public concerns have been expressed that current regulatory criteria for Cu in fresh water are not adequately protective of olfactory function in salmonids (e.g., OSU 2007; Pearson 2007). These concerns have largely been raised because some Cu concentrations that have caused olfactory impairment in salmonids in the laboratory are less than Cu concentrations that have been shown to reduce salmonid survival, growth, or reproduction (the effects endpoints that are typically considered in deriving ambient water quality criteria). However, two important and interrelated points that must be considered: (1) freshwater Cu criteria are "driven" by the sensitivities of several invertebrate species that are more sensitive than the olfactory impairment threshold in salmonids when (2) the influence of water chemistry on Cu bioavailability is properly considered in deriving Cu criteria. Bioavailability refers to the ability of various chemical forms of Cu to interact with receptors on the surface(s) of organisms and thus directly cause toxicity or uptake by the organisms. The toxicity of Cu and other metals to aquatic organisms is a function of water chemistry. For example, acute Cu toxicity in fresh water generally decreases as pH, water hardness (Ca2+ and Mg2+), alkalinity, and dissolved organic carbon (DOC) concentrations increase (Meyer et al. 2007). The U.S. Environmental Protection Agency (USEPA) has recommended hardness-based freshwater aquatic life criteria for Cu and other metals since the 1980s (e.g., USEPA 1985); and hardness-based metals criteria decrease (i.e., become more restrictive) as water hardness decreases. More recently, the USEPA has recommended freshwater aquatic life criteria for Cu based on the biotic ligand model (BLM; USEPA 2007), which accounts for the influence of multiple water chemistry parameters, including DOC, pH, alkalinity, Ca2+, Mg2+, and several other cations and anions. The BLM-based Cu criteria generally decrease as DOC concentration, pH, alkalinity, and water hardness decrease. Because DOC has a stronger influence on Cu bioavailability than water hardness, hardness-based and BLM-based Cu criteria can differ considerably. For example, in water that has low DOC and high hardness, the hardness-based Cu criterion would be relatively high (because it is driven by the high hardness) but the BLM-based Cu criterion would be relatively low (because it is driven by the low DOC). Thus, any evaluation of the protectiveness of Cu criteria against a given effect, such as olfactory impairment, must properly account for the chemistry of the exposure water. Meyer et al. (2013) compiled data on Cu-induced olfactory impairment and olfactory-induced behavioral effects from tests in which BLM parameters were measured. They demonstrated that the USEPA's BLM-based freshwater life criteria for Cu are protective against olfactory impairment, because it adequately accounts for water chemistry (whereas the USEPA's hardness-based Cu criteria are not consistently protective). Olfactory impairment by Cu is now receiving increased attention in Canada and Europe (e.g., Wall 2013; Stang 2013). Accordingly, in this paper we have expanded the analysis of Meyer et al. (2013) to consider copper guidelines from various other countries and whether these guidelines are protective against olfactory impairment.

Feb 23, 2014

By Frederic Chavan, Hans Jakob Windier, Shane Yanagisawa, Willy Ritz

The Zurichberg twin track tunnel is the main segment of the Swiss Federal Railway's new expressline. A heavy concrete lining with a circular cross-section was chosen to cope with the swelling tendency of the surrounding rock. The 4,356 m (14,300 ft) long, 11.52 m (38 ft) diameter tunnel was driven using a shielded Robbins TBM. A 1.20 m (4 ft) wide, 25 cm (10 in) thick precast lining was placed from within the shield tail as the excavation progressed. Tunnel excavation and initial lining operation were completed in 18 months, averaging 11.86 m/day (40 ft/day) in two nine hour shifts. After breaking through, the final 28 cm (11 in) thick concrete arch lining was cast in place.

Jan 1, 1989

By Naeimeh Shabani, Hamid Mirzaie, Javid Sadeghi, Hoda Jafarizadeh-Malmiri, Afshin Javadi

Iron oxide nanoparticles (Fe3O4 NPs), despite their small size, are stable and have a large surface area that allows for absorption and removal of ions as well as turbidity in a short period of time. Thus, the present study addressed the synthesis and characterization of Fe3O4 NPs synthesized using the co-precipitation method and evaluated their effect on the coagulation process in water treatment. The Fe3O4 NPs characteristics were evaluated as follows: magnetic properties were measured using a vibrating sample magnetometer (VSM), surface area using Brunauer–Emmett–Teller (BET), crystal phase using X-ray diffraction (XRD), and morphology using field emission scanning electron microscopy (FESEM). In addition, the effects of the synthetic Fe3O4 NPs on the turbidity reduction of water in various pH levels were evaluated. The synthesized Fe3O4 NPs were without any impurity in the sizes of 22–32 nm, surface area of 99.6 m2/g, pores’ mean diameter size of approximately 10.6 nm, and maximum magnetic saturation of 66.21 emu/gram (emu/g). Using 0.2 g of synthetic Fe3O4 NPs with an initial turbidity of 17 NTU and pH of 6 could reduce all water turbidity (100%). Considering the cheap and facile production and separation, as well as the possibility to reuse them and reduce the sludge water content, iron oxide Fe3O4 NPs can be effectively used for turbidity reduction in the water treatment process.

Oct 26, 2020

By J. E. Friant

The Mini-Disc TM cutter drill bit is a radical design departure from the traditional tri-cone rock drill bit. Miniature disc type cutting tools as small as 3.25 inches (82.5 mm) diameter are fitted to a bit body to cut individual concentric kerfs. The action is the same as that commonly used on large tunnel boring machines but miniaturized. The high performance rate and efficiency of a disc cutter are the result of producing a large proportion rock chips rather than sand or powder. The Mini-Disc TM drill bit, referred to as the "Disc Bit" has other unique features as well. It can be re-greased between runs. It can be rebuilt in the field in about 15 minutes, cutters can be replaced and the Disc-Bit appears to require less down hole hydraulic power than conventional bits. Thoroughly tested in the laboratory, the bit has recently been undergoing field trials in well drilling, blast hole drilling and shaft drilling. As any engineer knows, the laboratory cannot shake out all the problems but it eliminates the more glaring weaknesses. Performance results have been exhilarating, and a few mechanical problems were discovered and largely overcome. This paper is a progress report.

Jan 1, 1999

By David A. Campbell

There has been a long history of ironmaking on the North East coast of England centered around the River Tees. The industry developed here because of the availability of good coking coals to the North in Co. Durham, and the discovery in 1851 of ironstone in the nearby Cleveland Hills, South of the .River. Cleveland ironstone is relatively poor in quality, with an iron content not exceeding h% and high proportion of sulphur and phosphorous. The iron exists in chemical association with alumina and silica, and physical beneficiation processes involve a serious loss in iron unless the upgrading is limited, when the economics of the process become doubtful. Over the years, richer foreign ores have replaced the local ironstone, and the last operating mine was closed in 1964.

Jan 1, 1982

By Juan J. Monsalve, AMAN SONI, ALEX PFREUNDSCHUH, Nino Ripepi

Ground control failures are one of the main causes of accidents in the underground stone mining industry. Some of the fundamental tools for rockfall hazard identification are related to rock mass characterization and geotechnical discontinuity mapping. Recent technological advances in these methods are related to remote sensing techniques and point cloud processing software for automated discontinuity mapping. Remote sensing techniques, such as LiDAR and photogrammetry, generate multimillion point clouds with millimetric precision, capturing the structure of the rock mass. The automated point cloud processing tools offer alternative algorithm-based methods to characterize and map these discontinuities. However, their applicability is constrained by multiple factors such as site specific conditions of the rock mass and the parameters used within the mapping algorithms. This paper evaluates the performance of automated discontinuity extraction software compared with manual virtual discontinuity mapping. Sampling windows from laser-scanned sections in an underground limestone mine are defined and mapped using discontinuity set extractor (DSE). Results from the virtual discontinuity software are compared with manually extracted fractures from I-Site based on reviewing orientation, trace length, spacing, number of extracted discontinuities, and processing time. The analysis determined that the automated mapping algorithm was able to identify the same discontinuity sets that had been manually mapped. The automated mapping software mapped an excessive amount of smaller fractures, which caused the comparison of both mapping techniques to be unsuccessful in terms of trace length and spacing.

Mar 19, 2021