Search Documents

By T. J. Lien

AMAX Coal Company's Belle Ayr coal dryer is the first industry attempt to commercialize sub-bituminous coal drying which has been the subject of laboratory and pilot plant tests for almost two decades. This paper presents the historical background, construction, start-up and operation of this adaption of fluidized bed coal drying technology to Powder River Basin coal. The flowsheet and operational problems encountered during plant start-up are discussed together with general material balance and product quality.

Jan 1, 1990

By S. Dawson

The Republic of South Africa has become a major producer of opencast coal in recent years. Opencast production commenced in 1970 and by 1977 some 10 million run of mine tonnes were being produced annually, Since then surface mine activity has increased to more than 60 million tonnes which represents approximately one third of the total annual South African? coal production. Whilst a substantial portion of this production is exported, the majority is used in the domestic market, The largest consumer, being the South?\ African Electricity Commission (Eskom), produces most of South Africa's electricity using coal fired power stations,

Jan 1, 1990

By Zhonglin Ye, Guangping Dai, Ba Zhang, Yonggang Wei, Shiwei Zhou, Bo Li, Hua Wang

Decreasing copper content in slag is critical for improving copper recovery, where apparent viscosity is the main factor affecting the separation of matte/copper from the slag. The viscous behavior of copper converter slag was investigated during reduction process in this paper, and its non-Newtonian viscous behavior and shear thickening characteristics were clarified. The effects of silicate structure and solid particles in the melt on the slag apparent viscosity were investigated. As slag cleaning proceeded in an electric furnace, the magnetite gradually transformed into ferrous oxide, increasing the FeO/SiO2 ratio. With this ratio increased from 1.2 to 2.0, the slag structure was simplified, and its apparent viscosity decreased from 0.26 to 0.12 Pa·s at 1523 K. The iron phase was excessively reduced to metallic state; the slag contained metallic copper-iron alloy particles, increasing apparent viscosity. The apparent viscosity and phase structure of the slag corresponding to the iron phase reduction process were analyzed in detail; the results obtained in the present study are of great significance to the reasonable control of the converter copper slag cleaning process.

Nov 7, 2022

By James K. Wright

This chapter will discuss the use of financial models as an evaluation tool for various phases of decision making from exploration strategy to the analysis of a producing mine. The text of this chapter was not received in time for printing.

Jan 1, 1979

By Louis M. Schlesinger, Michael J. Garska, Joel F. Hutwelker, James T. Jr. Tanner

A pilot plant was constructed and operated to investigate the column flotation of 20 x 200 mesh North Carolina phosphate ore, using high throughput, high solids operating conditions developed at the NCSU Minerals Research Laboratory. Flotation was performed at 45% solids in a 9.5 cm (3.75 in.) diameter by 2.26 m (7.4 ft.) tall column at throughputs of 19.1 t/hr/m2 (2.0 stph/ft2) and 31.7 t/hr/m2 (3.3 stph/ft2). Recoveries in excess of 98% of the phosphate value were obtained at the lower throughput -- while obtaining concentrate grades containing over 28% P205 (61.2% BPL) at that recovery. Recoveries of about 95% of the phosphate value were obtained at the higher throughput, while making a concentrate averaging 27.6% P205 (60.3% BPL). In addition, a better understanding of the variables governing the column flotation of coarse nonmetallic minerals was gained. Variables examined included superficial air velocity, throughput (superficial feed velocity), frother type, frother dosage, and bias rate.

Jan 1, 1993

By Verya Nasri, Mehdi Bakhshi

"Fiber reinforcement has emerged as an alternative to steel bars in precast concrete segments due to advantages such as saving cost and reducing production time while developing a more robust product with improved handling and long-term durability. ACI recently drafted a new report as the first design guideline on FRC tunnel segments to provide specific guidance for this emerging technology. ACI document offers general information on the history of FRC precast segments from tunneling projects throughout the world; a procedure for structural analysis and design based on governing load cases, and a description of the material parameters, tests and analyses required to complete the design. This paper summarizes the design considerations in this ACI guideline prepared by the authors of this paper as the main contributors. Application of this guideline to design of a tunnel with an internal diameter of 5.5 m (18 ft) results in elimination of steel bars.INTRODUCTIONPrecast concrete segments are installed to support the tunnel excavation behind the Tunnel Boring Machine (TBM) in soft ground and weak rock applications. The TBM advances by thrusting off the completed rings of precast concrete segments that provide both the initial and final ground support as part of a one-pass lining system. These segments are typically designed to resist the permanent loads from the ground and groundwater as well as the temporary loads from production, transportation and construction. Tunnel segments are generally reinforced to resist the tensile stresses at both the Serviceability (SLS) and the Ultimate Limit States (ULS). With traditional rebar, a significant amount of labor is needed to assemble the cages and place the rebar, which results in higher production costs.Fiber Reinforced Concrete (FRC) can be used to enhance the production, handling, and placement of precast concrete segments. This is because of the uniform dispersion of fibers throughout the segment to include the concrete cover, which is very advantageous for resisting the bursting and spalling stresses. These stresses develop as a result of the high loads induced on the segments during the TBM jacking process. The presence of fiber in the concrete matrix helps mitigate against unintentional impact loads during segment handling and tunnel construction operations."

Jan 1, 2016

By Ian Farrell, Josh Stowe, Eric Wingeard

Tailings transport system design is generally based on identifying the minimum and maximum process boundary conditions for pump selection and pipeline sizing. The approach is robust and well-proven. However, the approach has the potential to skew selections to operating scenarios that have a very low likelihood of occurring, such as the combination of high solids throughput and low tailings solids concentration. The approach can result in a tailings transport system design that is overly conservative. A probabilistic method-based approach captures the independent variability of design inputs and the combined likelihood of outcomes. This approach identifies the process conditions that have the highest likelihood of occurrence and are most applicable to equipment and pipeline selections. An outline of a probabilistic-based approach to tailings transport system design and the resulting selections is provided in this article. The probabilistic-based system design is compared to the outcomes from the traditional approach. The benefits and challenges to this approach are discussed and recommendations for utilizing this approach for tailings transport system design are provided.

Mar 31, 2021

By E. A. Zawadzki

The problem of pollution of water by mine drainage is at least as old as the mining industry itself. However, research on the formation, composition, treatment, and abatement of mine water is a relatively recent historical event. At Bituminous Coal Research, Inc., acid mine drainage control has been an important area of work since 1944, at which time BCR began sponsorship of research at West Virginia University. The work at West Virginia University involved a detailed study of the acid mine drainage problem and led to the identification of iron oxidizing bacteria as important factors in the formation of acid mine water. The results of this research were summarized in 1954 by Temple and Koehler (1) who concluded that "no practical solution for the problem" of controlling acid mine drainage is yet known.?

Jan 1, 1967

A knowledge of airway friction factor (K-factor) is necessary to designing mine ventilation systems for least cost and optimum effectiveness. The friction factor used must be accurate and reliable to estimate correctly roadway resistances and pressure sources for required flows. Though the resistance to flow offered by mine airways has been an object of study over the last half century, no accurate relation has yet been established from which the prediction of the resistance of a projected airway can be made. In Kentucky, only limited and incomplete data on local K-factors are available. Therefore, there is a need for field investigations to determine these values in-situ for existing mining conditions. The author describes a study concerning K-factor that was carried out in ten coal mines, located in eastern and western Kentucky. The results of these investigations are presented in both tabular and graphical form.

Jan 1, 1991

By Thiemo Hagedorn, Gerhard Weissbach, Ralph Bergmann, Wilhelm J. Kogelmann

The objective of this unique method is to multiply the advance rate of conventional tunneling while improving both ground control and the safety of the crew. The high advance rate is achieved by concurrent rock excavation and installation of concrete lining at fully synchronized work phases. The novel TACHUSMATIC system consists of a high-production, robotic cutter boom, an automated slip form and continuous mucking and conveying. This novel system utilizes the inherent bearing capacity of the rock that is activated by a small, initial deformation. The supporting resistance is then provided both by the rock mass itself and the pumped in concrete lining. During the hardening of the concrete, the hydraulic cylinders of the TACHUSMATIC automatically apply the appropriate support resistance, thus providing safe ground control. This novel tunneling system is practically a fully automated, fail-safe NATM that does not require highly skilled engineers and crew. The TACHUSMATIC can be used for construction of circular, rectangular and horseshoe-shaped tunnels. When equipped with the Alpine Multi-Tool Miner (MTM) systems, the machine can work in a wide range of ground and rock conditions. The use of novel, diamond-tipped cutter bits (picks) will increase hard rock cutting capabilities and will significantly reduce pick consumption. Because of its moderate cost, the novel system is an economic alternative to conventional tunneling even at short drivages. A new installation is cost-effective for tunnels longer than 750 meters (2,500 ft.) At a typical tunneling project, the cost permeter is about 25% lower than with conventional methods.

Jan 1, 2003

By Brian Fulcher, Matthew Bartlett, Jarrett E. Carlson

This paper discusses the challenges to complete the construction of two large underground Metro stations and connecting tunnels in the Tren Urbano system. The completion work includes the installation of specialized mechanical and electrical systems, extensive architectural finishing as well as coordination with systemwide power and controls installed by others. A unique feature of this project was the simultaneous design and construction of the structural/civil/architectural/mechanical/electrical works by KKZ separately from the power and control systems under the management of the Owner, its consultants and other contractors. Completion of this project comes after almost six years of continuous design and construction in a dense urban environment. The project was confronted by many challenges that could only be met with the combined efforts of the Joint Venture team in close cooperation with the Owner and its System wide Contractor. This paper will also address many of the major design and construction changes implemented to suit the Owner’s requirements.

Jan 1, 2003

By R. M. G. Machunter

The presence of ultra-fine particles affects the separation performance of wet gravity separation equipment. Several studies have been undertaken to establish the maximum level of these particulates that can be tolerated by spiral separators and it has been found that unless the ultra-fine material is effectively processed, relatively low proportions in the ROM material combined with high feed rates can result in degradation in plant performance and/or excessive water consumption. The maximum level of particulate material in the process water has been determined by examination of separation performance of spiral separators under varying slime loading. This work has been conducted utilizing various feed sources and a robust ‘rule-of-thumb’ has been derived.

Jan 1, 2005

By N. Wahl, D. M. Blackketter, R. Thornton

This paper evaluated using a water-filled abandoned mine (Orphan Boy) as a heat source for a 240- kW closed-loop heat pump with the goal of heating a 2,000-m2 building. The mine has a 245-m vertical shaft connected to a large stope by three horizontal cross-cut shafts. There is 1,250 x 106 L of water at a consistent temperature of 24-26° C that is available mostly in the stope. The only heat exchanger placement option is in the vertical shaft. Therefore, the focus was to model heat exchanger placement in the vertical shaft to determine the extent to which the systems will induce thermal currents between the stope and vertical shaft. Modeling of thermal currents, temperature profiles and heat contribution from the ground was done using finite difference and computational fluid dynamics. An optimal configuration was determined showing sufficient water movement and heat transfer will occur with a low water temperature in the shaft above 20° C. This project supports a U.S. Department of Energy (DOE) grant that will implement the full-scale system.

Jan 1, 2013

By T. Hayashi

A sophisticated process of extracting ultrafine sulfide mineral particles of under 1µm size suspended in clay slurry has been developed through studies of electrochemical properties of particle surface. Experimental procedure and data of the process applied to some clay ores containing sphalerite and pyrite, and molybdenite and other sulfide minerals are reported. Discussions concentrated on the function of process reagents, particularly on various modifying reagents, and on the effect of dispersed or flocculated state of ultrafine particles in slurry which affect significantly the performance of the process.

Jan 1, 1982

By W. K. Katoto

The Tailings Leach Plant (TLP) of the Zambia Consolidated Copper Mines Ltd at Nchanga was commissioned in 1974 as the world's first largest successfully operated agitation leach SX-EW plant for copper production. The design, development and operation of the plant soon after commissioning termed as TLP stage II has been described by Holmes et al (1). In the initial phase the plant was designed to treat approximately 25,000 tonnes per day of current flotation tailings from the Nchanga Concentrator operations, and had a design capacity to produce 75,000 tonnes per annum of copper. Further expansion took place in 1986, and TLP stage III was successfully commissioned to treat an additional 20,000 -25,000 tonnes per day of large reserves (over 135m tonnes) of reclaimed tailings stockpiled since the early 1930's in four paddock type tailings dams (T01 to T04). The salient feature of TLP stage III expansion described by S K Mwenechanya et al (2 -3) was the installation of the world's largest Horizontal Belt Filter Plant with 26 filters each of 80 m2 filtration area.

Jan 1, 1996

By Peter B. Knuckey

1, Introduction Location Kalengwa mine is located in the North Western Province of Zambia, 402 kilometre by unpaved road to the west of Kitwe, which is roughly in the centre of the Zambian Copperbelt, well known as one of the world's centres of copper mining. Its position is illustrated on the map of Africa in Figure 1 and on the map of Zambia in Figure 2. It is a mine of Roan Consolidated Mines Limited whose other properties, Mufulira, Luanshya, Chambishi and Chibuluma Mines, are all located on the Copperbelt. It is managed by the Chibuluma Division of the company. The rate of production from Kalengwa will vary from 12 000 to 17 000 tonnes of saleable copper a year over the next six years. Kalengwa did not exist as a place until the first prospecting parties and later the mine became established and the early working population was recruited entirely from small villages in the surrounding area as much as thirty miles away. The mining area consists of fourteen mining locations amounting to 3.35 square kilometres and the land may be used for any purpose connected with mining, including housing, wood cutting and other utilities. The whole area is, except for minor undulations, a fairly flat plateau with main rivers running from north to south and flood basins known as "dambos" located in a general east west direction. Vegetation is, with the exception of the grassy dambos, temperate forest with relatively light undergrowth. Game of great variety is prolific, as is the associated tsetse fly.

Jan 1, 1971

By Jackson M. Langton

INTRODUCTION The Morenci-Metcalf district is located on the southern slope of the white Mountains in Greenlee County, Arizona. Both porphyry copper deposits are four to six miles northwest of Clifton, the county seat, and the new Metcalf mine is situated approximately one mile northeast of the Morenci open pit (Figure 1). Chase Creek, a south-flowing tributary of the San Francisco River, dissects the district and separates the two ore bodies. More than 1,200 exploration and development drill holes have been completed in the district and the Morenci-Metcalf ore bodies have been delineated on a 400-foot grid. Recently initiated drilling programs have revealed new data about deeper protore and associated hypogene alteration. This information, correlated with surface mapping and petrographic studies, was utilized to propose a plausible geochronologic sequence for this region. The reasoning behind this study has been helpful in locating new ore beneath leached capping indicative of only protore mineralization. The scope of this paper is to establish a practical solution to a highly theoretical problem of ore genesis and to familiarize the reader with stratigraphic, structural, and mineralogic events responsible for localizing ore in this district. Continued research will possibly alter the proposed time span and relative displacements, but it is doubtful that the order of events will vary significantly. Geochronologic conclusions are therefore presented as general hypotheses and additional geologic mapping,

Jan 1, 1972

By Ralph W. Barbaro

In the mineral industry, the objective of a mining venture is to extract, process, and market a mineral commodity in such a manner that the profit of the venture is maximized. In a mining venture, a company normally has control over mine production scheduling, the selection and location of processing facilities (mineral beneficiation plants, smelting plants, refineries, or blending facilities), processed ore blending, and the selection of markets. The flexibility of the above factors provides many alternatives to satisfy the needs of each market with regard to quantity and quality of ore. The purpose of this paper is to present a mathematical model for determining the alternative that yields the maximum profit. Production planning is generally concerned with the best utilization of fixed resources, more specifically, with the determination of production and inventory levels to meet fluctuating demand requirements. A mine can be any source of ore such as an entire mine, a production unit within a mine, or an independent supplier. The objective of production scheduling is to determine the times at which each mine will be used and to allocate a required level of production. Production planning and scheduling problems are intimately associated with the location of new and existing mines and processing facilities. Although the location of the mines is usually fixed, there can be considerable flexibility in locating new processing facilities, in the selection of the processing plant, and in blending the ore before and after processing.

Jan 1, 1983

By J. Duran

Mining at Phoenix is currently done by surface operation in the Fortitude and Bonanza Pits, at a combined rate of approximately 110,000 tons per day. A portion of the ore bodies targeted by these pits was mined previously by underground mining methods, dating back to the mid to late 1800?s. Most of the underground workings (voids) are located in the west central area of the Bonanza Pit. The surface operation requires excavation through voids, and there is a risk of pit floor subsidence that has to be addressed. This paper presents a review of the risk mitigation measures that were implemented to reduce risks to people and equipment working in the area.

Feb 23, 2014

By M. Ralchenko, C. Samson, M. Svilans, C. Walsh

"Through-the-Earth (TTE) radio has been proposed as a means of emergency communications in mines. The propagation of a TTE radio signal depends chiefly on the subsurface conductivity distribution. Robust forward models of signal propagation can be computed based on a realistic conductivity estimate. These models can be used, for example, to optimize frequency, estimate signal range, identify zones of anomalously strong or weak signals, or to optimize the position of the above-ground TTE radio unit. A method was developed to determine the conductivity distribution of a mine overburden using TTE radio transmission data. At multiple locations in an underground test mine, we recorded a wideband electromagnetic signal, spanning a frequency range of approximately 500 to 8,500 Hz, transmitted from a vertical magnetic dipole at the surface. Using a finite-difference time-domain forward modeling code, a layered Earth conductivity model that accounts for topography was fitted to the observed data, which minimizes the difference between the calculated and observed attenuations for each transmitter-receiver pair, for each frequency of interest. Introduction and objectiveThrough-the-Earth (TTE) radio has been proposed for emergency underground communications. The most common type of TTE radio is based on the transmission and reception of signals by electromagnetic induction. These signals are in the extremely low to very low frequency range — in practice, between 400 and 9,000 Hz. This technology was historically developed for mine safety, although recently other applications have been suggested, such as communications in civilian infrastructure like high-rise buildings or tunnels, in the military, and even for wireless detonation and activation. In a coal mine, which is a setting of particular importance for TTE radio due to the higher risk of accidents, day-to-day communications can be done through a wired link. High-frequency line-ofsight systems, whose signals cannot penetrate rock, are also used for communications from nonfixed points. Another option is a leaky feeder system, which is a permutation of a line-ofsight system and a wired link, where a partially shielded coaxial cable allows the signal to “leak” (Delogne, 1982). In an incident such as a mine collapse or explosion, a TTE radio system can still provide a communication link, as wired systems can be severed, and line-ofsight systems cannot penetrate through collapsed portions of the mine, or to the surface (Forooshani et al., 2013; Yarkan et al., 2009)."

Jan 7, 2018