Search Documents

By David Hopkins, Steve Klein, Bradford Townsend, Ed Sum, Derek Penrice

INTRODUCTION The Transbay-Caltrain Downtown Extension (DTX) Project involves the construction of an approximately 1.5-mile rail line that will extend Caltrain commuter service and the future California High Speed Rail system into downtown San Francisco. The underground rail extension will be constructed by mined tunnel and cut-and-cover methods. Tunneling challenges include difficult ground conditions, low rock cover, the presence of historic buildings along the alignment, and the large tunnel span, ranging from approximately 50 to 65 feet. Three mined tunnel construction methods were evaluated: the Stacked Drift Method, the New Austrian Tunneling Method/Sequential Excavation Method (NATM/SEM), and Tunnel Boring Machines (TBM). This paper describes the challenges presented within the mined tunnel section, and summarizes the evaluation of tunneling methods that led to the selection of NATM/SEM. PROJECT OVERVIEW The existing Transbay Terminal opened in downtown San Francisco in 1939. This facility is antiquated, and does not meet current building seismic safety standards or the transportation needs of the Bay Area. For these reasons, San Francisco voters approved Proposition H in 1999, which proposed to construct a new or rebuilt regional transit center at the site of the existing terminal and extend Caltrain commuter rail ser-vice to the new transit center. The new transit center is the hub of the Transbay Transit Center (TTC) Program, which will greatly enhance regional transit service by providing connectivity for six Bay Area transit providers at one facility. The program will be the largest inter-modal centerwest of New York City. The TTC Program is comprised of two major projects, the Transit

Jan 1, 2007

By A. Duerksen

Surface coal mining in West Virginia has supplied energy to the eastern coast of the United States for over a century. The coal mining industry has been forced to adapt as societal demands regarding health, safety, and environmental impacts have changed with time. More recent pressure has called for another iteration of change: long-term post-mining sustainability. The research presented in this paper investigates one potential solution?or component of a solution?to improve mining sustainability in Appalachia: post-mining wind power. This paper intends to demonstrate and explain the feasibility of synergistic mine closure and wind development. Wind conditions at three reclaimed mine sites in West Virginia were monitored in order to develop representative case studies for post-mining wind power. This paper contains a summary of the literature consulted to plan the site assessments, the methodology employed to execute them, the analysis steps undertaken to derive conclusions, and a discussion of all findings. This research has found that significant cost savings can be yielded from synergistic mine closure and wind development, as compared to greenfield wind development. Though wind conditions themselves remain the primary driver for site feasibility, post-mining wind power is a practice with significant promise for improving project economics, contributing to renewable energy development, enhancing company-community relations, providing local employment opportunities, and exemplifying sustainable business practices in Appalachia.

Jan 1, 2012

The design/optimization of the pump and cyclones to maximize grinding circuit efficiency first requires a concise understanding of, and clearly defined specifications for, desired grinding circuit performance. Subsequently, the pump and cyclone performances that provide the desired grinding circuit performance can be defined. Once the performance requirements of each process unit are determined, selection of physical equipment parameters that will deliver those performances can be carried out. The Functional Performance Equation shows that there are two distinct efficiencies in closed circuit ball milling. One of these, ?Circuit Classification System Efficiency? (CSE), is the fraction of ?coarse? material inside the ball mill upon which grinding energy is deliberately expended, versus the remaining fraction of ?fines? or finished size material inside the mill, upon which grinding energy is wasted (on over-grinding). The role of the pump and cyclones is to maximize CSE, which is the desired grinding circuit performance. The obtainable, target CSE for any given circuit can be estimated, for example by referring to a plant data base of CSE?s. Design/optimization guidelines then allow us to specify the pump and cyclone performances that will achieve the target CSE. This paper outlines the step-by-step, systematic method of pump and cyclone selection which maximizes CSE. Numerous examples of its successful application are provided.

Jan 1, 2011

By M. Dobbins

The advent of the more efficient and effective rare-earth roll (RER) separator in the early 1980?s began a new era of dry magnetic separation. The RER units quickly became the separator of choice within the materials processing industry. Though RER separators are now commonplace throughout the world, only modest advancements have been made to the original design. This paper details recent, more significant, rare-earth magnetic separation developments. These developments maintain the best features of existing technology while minimizing shortcomings. The discussion includes discerning features that aid in better metallurgical performance. Also discussed are improved mechanical aspects that allow for both easier operation and maintenance. Performance details from various test programs are included.

Jan 1, 2009

By Brendan Demich, Joseph McGuire, Emily J. Haas

Near misses recorded and reported by workers can provide awarenessto the potential causes of injury and prompt safety management initiatives. Although most companies require near-miss reporting, it is unclear what the value of these reports are, if any, and how they influence subsequent actions or controls to reduce on-the-job risks. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a case study with an aggregates company in which near-miss reports were analyzed at each of their locations over an entire quarter during the summer of 2018. Within that quarter, workers recorded 249 near misses. Of those, 167 were valid near misses that occurred at work. Researchers coded the reports using a qualitative 5 × 5 risk matrix. Of the 167 near misses, 19% were deemed low risk, 25% moderate risk, 30% high risk, and 26% critical risk. Several patterns in the near-miss incidents were documented, including classification of incidents and common corrective actions referenced (i.e., elimination/substitution, engineering control or redesign, work process/procedures, and personal protective equipment). The analysis provides insight into ways that risk communication and management programs can be improved to reengage workers and their situational awareness on the job.

By Thomas Novak, Sampurna Arya

Controlling dust generation and keeping it below permissible limits to meet federal dust standards at the working face of a roomand-pillar coal mine is a challenge for a mine operator. With the recent changes in federal dust regulations requiring lower worker exposure, maintaining compliance has become increasingly difficult. The current most effective practice of dust control at a continuous miner face in an underground mine is the use of a flooded-bed scrubber. A study carried out by the National Institute for Occupational Safety and Health (NIOSH) indicated that a flooded-bed scrubber could achieve cleaning efficiencies between 58 and 90%. But, the operation of such a system is maintenance intensive. The flooded-bed scrubber screen becomes clogged with dust particles and requires frequent cleaning to maintain performance. However, the dust control issue is not solely a mining industry problem. Other industries face similar issues. The University of Kentucky collaborated with Toyota Motor Manufacturing on the development of a novel wet scrubber, called the vortecone scrubber, for capturing oversprayed paint particles in automotive paint booths. The vortecone scrubber achieved a cleaning efficiency of 99% and required minimal maintenance. This study aims to assess the ability of this vortecone scrubber to capture respirable dust in an underground coal mine. The paper presents the results of computational fluid dynamics (CFD) modeling of this vortecone scrubber. It discusses the effects of air quantity and dust particle size on the performance of the scrubber.

By Rolf Birger Pedersen, Alden Ross Denny

"Synthetic Aperature Sonar (SAS) is a powerful tool for ultra-high resolution marine survey. The Kongsberg HiSAS system deployed on the HUGIN AUV has a rangeindependent resolution of 3x3 cm for sonar image and ~10x10cm for the interferometric bathymetry product [1]. This resolution is achievable for areas up to 50 km2 on a single survey mission providing huge multi-attribute datasets. This technology, originally designed for military and oil-industry applications, has the potential to revolutionize scientific seafloor mapping. The extreme resolution of this technique allows for deposit mapping in and around seafloor hydrothermal systems, including the discovery of extinct venting structures. By clearly distinguishing between volcanic and hydrothermal landscapes based on features below the resolution of conventional multibeam systems, SAS enables an entirely new level of hydrothermal deposit survey. Additionally due to the extreme resolution of this survey technology, repeat survey and change detection should allow centimeter-scale changes in deposit morphology to be routinely detected over an entire hydrothermally venting region. In collaboration with the EU funded MIDAS project, the Centre for Geobiology at the University of Bergen will deploy the HUGIN AUV this summer at two distinct shallow venting systems on the Arctic Mid-Ocean Ridge system. The AUV will collect repeat bathymetry at the Jan Mayen Vent Field, and extend the SAS coverage to include newly discovered venting sites. We will present the preliminary findings of this expedition, including the first deposit estimations made from full-resolution SAS mosaics."

Sep 1, 2014

By D. Komljenovic, V. Kecojevic

Selection of the best possible truck type (model) is of crucial importance for the mine decision-makers. In this paper, authors contribute to the body of knowledge by developing a novel methodology for the selection of mining truck. Both the Coefficient of Technical Level (CTL) and Analytic Hierarchy Process (AHP) methods were used in this study. The CTL represents a mathematical function which takes into consideration the interrelations among the main technical parameters of mining trucks. The authors developed a hierarchical structure where both attribute categories and their importance, i.e. priority or weight in the selection process were determined. For each category, a number of sub-attributes and their priorities were assigned, and a pairwise comparison among them was performed using the AHP method. In the final part of the study, the CTL was integrated into the AHP and represents a holistic approach in the selection of mining trucks. A case study on 180 tonnes truck category offered by five manufacturers was carried out. A sensitivity study of obtained results was also performed indicating a very stable solution. The methodology presented in this paper may be used by mining operators to help in the selection of a specific type when acquiring a new truck. It may also be used by equipment manufacturers to help in analysis of potential benefits of envisaged modifications concerning an existing truck type and/or development of a new type.

Jan 1, 2007

By Emad Iskander

The seepage forces generated around pressurized water tunnels in rock are investigated using the analysis tools of geomechanics. The theoretical background of the two-phase material behavior is explained and the equations of motion and continuity are presented. Applications on two case studies typically occurring in practice deal with the required minimum rock cover for a pressurized tunnel and the separation between two tunnels carrying different heads. The rock mass behavior as described by the Mohr-Coulomb and Hoek-Brown material models is investigated by numerical analyses and the results are compared. The effect of key material parameters on the safety factors and the associated modes of failure is discussed.

Jan 1, 2008

By S. Frimpong

Cable shovel requires continuous monitoring through excavation to achieve reliability, longevity and economic usage. The operating environment and the stress and deformation fields on the front-end assembly must continually be monitored to avoid random fatigue failure. In this paper, the authors advance frontiers of cable shovel reliability through real-time stress and deformation monitoring during excavation. Cable shovel boom stress and deformation analysis are developed using a combination of flexible and rigid body approach. A virtual prototype is developed to simulate the cable shovel excavation in oil sands and to examine the motion, stress and local deformation of the boom. A numerical example is used examine cable shovel boom durability using stress and deformation fields simulation. The results show that stress and deformation are large around the joint between the upper body and the boom. The simulation of the effect of material properties on boom deformation shows that the deformation is larger in hard formation than in soft formation. The study provides a solid foundation for further study of failure life analysis of the cable shovel components.

Jan 1, 2006

By F. Khorram

Image processing is a technique that simulates the human vision system. This technique enables applying every statistical or intelligent operation to recognize differences. In this way this new technique is used in quality control systems in most industries. Studying sedimentary rocks is very important from the economic point of view. Some units of sedimentary sequences involve different mineral deposits, hydrocarbon and water resources. Therefore it is important to identify and classify different sedimentary rocks. Descriptive classification of sedimentary rocks is usually based on visual and textural features and chemical composition of a sample. In this paper different samples of a limestone mine in central part of Iran are classified. The samples were collected from different parts of the mine and crushed down in size from 2.58 cm to 3.58 cm. The rock samples were labeled based on percentage of chemical and lithological compositions. Each sample was assigned to one of the distinguished groups. The images of the samples were taken in appropriate environment and processed. A total of 74 features were extracted from the identified rock samples in all images. In order to feature dimensional decrease, principal component analysis method was used. Then Bayesian statistical algorithm was used as a useful tool for classification. Classification Correctness Rate (CCR), calculated for the test data sets are %88, %68, %61 and %72 for the first to fourth class respectively. Therefore it can be inferred that the extracted features of images are appropriate indicators for different samples identification. These precise results besides the advantages of image processing technique, which are increasing speed of operation and decreasing cost, appears to be a desirable success.

Jan 1, 2012

By K. Oraee

The empirical rock failure criteria play an important role in predicting the mechanical behavior of rocks, since affecting parameters on the behavioral properties of rocks are complex and numerous. Usually the empirical failure criteria are obtained by statistical methods, namely by means of fitting the mathematical function onto the experimental data. For evaluation and verification of the results, however, the quality and accuracy of the fit must be considered. This paper studies the efficiency and accuracy of conventional empirical rock failure criteria using a new approach, which is based on the analysis of uncertainty amplitude on the constant parameters of each criterion. The approach adopted here, is based on the combination of some parameters such as Mean Squared Error (MSE), Root Mean Squared Error (RMSE), type of function, degree of freedom and the confidence level of constants. Correlation coefficient (R2) is then a comprehensive test and can be used effectively for comparison and accuracy of empirical rock failure criteria.

Jan 1, 2012

By Eduardo Pimenta de Melo, Rambabu Pothina, Rajive Ganguli

Sensors are everywhere in the mining industry, with sensor information being used to monitor and operate processes. Therefore, when sensor information is wrong, economic losses can occur. Unfortunately, sensor errors are usually not detected till they become large. This is problematic as most calibrate their sensors no more than once a year (Beamex, n.d.). Using principles of data mining, where all relevant information is tapped to glean hidden information, Pothina [8] designed an algorithm to detect errors in temperature sensors in gold stripping circuit in Pogo mine, Alaska. This paper continued his work by analyzing the behavior of the algorithm on baseline data and testing the algorithm in new data and under more rigorous conditions. It also made a change to the algorithm. The modified algorithm performed very well in the new data. It also worked well under the new error conditions. Three types of errors were seeded, a fixed additive error (+ 2%), a fixed subtractive error (− 2%), and a noisy, normally distributed error, with a mean value of + 2%. Artificially seeded errors were detected within about 20 gold stripping cycles. Inherent bias in operation impacted algorithm performance by increasing the number of cycles needed to detect errors. This paper reinforced Pothina’s [8] conclusion that when data mining approach is used, sensor errors can be detected even when they are pretty low. Significant economic losses can thus be minimized.

By Martin Herrenknecht, Karin Bäppler

The last five years have seen a remarkable increase in tunnelling projects in both soft ground and hard rock applications. Part of the increase is a result of recent Research & Development efforts to improve Tunnel Boring Machine (TBM) adaptability, capability and reliability. This paper will review the latest innovations in the TBM industry and explain in detail the results of these innovations followed by a forecast where the technology will take the tunnelling industry in the future.

Jan 1, 2005

By Z. Hyder, M. Karmis

Underground or In-situ Coal Gasification (UCG or UICG), though not a new concept, is now attracting considerable global attention as a viable process to provide a "clean" and economic fuel from coal. Applying improved UICG technology to gasify deep, thin, and low-grade coal seams could vastly increase the amount of exploitable reserves. However, it is imperative that further development of this technology is based on integrating UCG practices and potential environmental impacts with accepted sustainability frameworks and processes. This paper evaluates the potential of UCG to conform to frameworks such as MMSD (Mining, Minerals and Sustainable Development), Natural Step and Green Engineering, in order to define its "sustainable" potential. The paper also discusses the potential contributions of UCG to sustainability during its design, operation, closure, and post-closure phases.

Jan 1, 2011

By D. W. Alexander

Researchers from the Office of Mine Safety and Health Research (OMSHR) of the National Institute for Occupational Safety and Health (NIOSH) completed field trials during coal mine rescue contests using simulated gas detectors in place of placards. The gas monitor simulator (GMS) devices replaced static, paper placards to deliver gas concentration data. Eleven teams were observed during the field contest, which was approved by the Mine Safety and Health Administration (MSHA). GMS devices were given to three team members, the captain, and both gasmen. Observation of teams revealed that team members changed behavior by acknowledging and sharing information more often while using the GMS. As a result of this research, it has been demonstrated that under the existing contest format, the newly developed GMS device may be used with no adverse impact on team contest performance. Furthermore, when GMS technology advantages are used, contest realism is improved. In the future, competency assessment may be incorporated.

Jan 1, 2011

By S. B. Bealko

In response to recent mining disasters and new mine rescue team legislation, NIOSH researchers conducted meetings across the United States with mine emergency response experts to investigate current needs and issues. Some of the issues include emergency response preparedness, mine rescue contests, real-life training capabilities, and training facilities. Many new teams are being formed that must be trained for mine rescue team competitions as well as be ready to respond to a variety of mine emergencies including a fire or explosion, a massive roof collapse, mine inundations, or vertical shaft rescue situations. Therefore, it is important that these teams are adequately prepared and trained. This paper presents a summary of domestic and international coal mine rescue training facilities and identifies those that provide unique, real-life, and/or state-of-the-art training. Research findings from this report will be used in further NIOSH investigations to improve coal mine rescue training. DISCLAIMER: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2009

By D. Kwietnewski

With all of the unknowns associated with tunnel construction, how does a contractor choose a roadheader? This paper presents a review of several models of roadheaders being used in today?s tunnel projects. The features of different models of roadheaders are presented and compared. Roadheader size and cutter power generally determine which roadheader is best for a particular job. We will also present a model for matching features of the roadheader to the anticipated ground conditions such that the most efficient machine is selected for the project.

Jan 1, 2011

By J. Drelich, M. Pawlik

An improved experimental procedure to measure contact angle has been consolidated with coal surface preparation involving polishing with abrasive paper, alumina powder, and a cloth, followed by ultrasonic and mechanical cleaning. Specifically, the captive-bubble measuring technique has been compared with the sessile-drop technique and the former has been recommended for the examination of the hydrophobic properties of coal surfaces. Results of the research program, which is currently under way, on the examination of the effect of the nature, amount, size, and distribution of mineral inclusions in coal, on its wettability are briefly reviewed.

Jan 1, 1999

By V. McLemore, A. Fakhimi, K. Donahue, D. Sweeney, V. Viterbo

In order to evaluate the relationships between weathering and durability and strength of rock samples from the Goathill North rock pile at the Molycorp Questa mine, NM, we conducted slake durability and point load tests. Slake durability index (ID2) values ranged from 84 to 98%. Point load strength index (Is50) averaged for all rock units ranged from 1.1 to 5.7 MPa. Results show a slight positive trend between ID2 and paste pH. Two populations of data are distinguishable when ID2 is plotted versus the percentages of chlorite, illite and internal friction angle. In general, Is50 values increase toward the interior of the rock pile. Preliminary conclusions indicate that the durability and strength of the rock pile material generally increase toward the interior of the rock pile. Pre-rock pile alteration and post-rock pile weathering history have affected the durability of the GHN rock pile samples.

Jan 1, 2007