Search Documents

By E. C. Westman, F. J. Shreve

This paper presents the design and construction of a multi-channel geophone array that improves tomographic imaging capabilities in both surface and underground mines. Especially important in the design of the array is sensor placement. Three issues related to sensor placement are addressed in this paper: 1) sensor placement in long, horizontal boreholes, 2) development of simple, robust, MSHA-acceptable clamping unit, and 3) orientation of the geophones within the borehole. Improved imaging capabilities will produce energy, environmental, and economic benefits by increasing exploration accuracy and reducing operating costs.

Jan 1, 2002

By Michael J. Robison, Wojciech F. Klecan, Robert L. Horner

Since 1928, nearly 64 km (40 mi) of tunnel have been excavated within the relatively soft Cooper Group, more commonly known as the “Cooper Marl,” for water supply and transporting wastewater in the Charleston area. The majority of these tunnels are unlined and still in operation, while others collapsed shortly after excavating. Tunnel behavior and support requirements vary considerably in this material due to differences in geotechnical properties. The 4.8 km (3 mi) long, 2.4 m (8 ft) diameter Bushy Park Water Tunnel, completed in 1997 for Charleston’s Commissioners of Public Works(CPW), required no ground support. By comparison, the 1.6 km (1 mi) long, 2.4 m (8 ft)diameter Harbor Wastewater Replacement Tunnel now under construction needs continuous support close to the advancing face, despite being located in the same geological formation. Case histories and general guidelines for designing tunnels in the Cooper Marl are presented.

Jan 1, 2001

By I. G. Gonçalves

For most industrial minerals, the color is directly associated with economic value. In terms of physics, the principal property that defines the term ?color? is the intensity of light reflected (or transmitted) by an object over the visible band, comprehended between 400 and 700 nm. This reflectance spectrum serves as the starting point for a variety of color-describing factors, the most common in the mineral industry being the brightness (TAPPI, 1977 and 1986) and the L*a*b* system (HunterLab, 2008). Quality specifications for mineral products are usually based on these colorimetric parameters. This market is becoming increasingly more selective and demanding over the quality of raw materials and alongside the traditionally controlled characteristics, such as particle size distribution and chemical composition, a trend exists towards the establishment of increasingly more strict specifications for the optical properties of these materials. This is due to the fact that most plants consuming these industrial minerals incorporate them into products in which the visual appearance is controlled. For these plants, most of them being the manufacturers of plastics, paper, paints, and ceramics, variations in the color of mineral materials result in difficulties to achieve the right color in the final product. Therefore, these plants set strict specifications for colorimetric parameters such as whiteness and yellowness, as well as colorimetric coordinates like L*, a*, and b*. For the manufacturer of industrial minerals, this translates into difficulties simply because many of these parameters are usually alien to the tradition of the mining industry. The main quality parameter in the kaolin industry is brightness, which is a weighted average of reflectance values over the range of 400-510 nm (TAPPI, 1977). Due to the lack of a better property, producers tend to use brightness to also assess the quality of the in situ ore and along the processing operations. However, the unprocessed kaolin is often accompanied by ?contaminant? minerals. For Brazilian kaolins, which are the object of this study, the most important contaminants are hematite (Fe2O3), goethite (FeOOH), and anatase (TiO2). Each of these contaminant minerals has a distinct color and behaves differently during the processing of the kaolin ore. Hematite and goethite in particular are particularly strong pigmenting agents and at concentrations as low as 100 ppm they can make the difference between a high-quality white pigment product for paper coating and waste material. As each Fe-bearing contaminant has a different color and responds differently to processing operations (for example, magnetic separation, chemical bleaching, selective flocculation, and/or flotation in the case of kaolin), the in situ brightness tends to show a poor correlation with the brightness of the final product. Brightness measurements are sometimes complemented with X-Ray Fluorescence (XRF) analysis of Fe and Ti, but the total oxide content provided by XRF is also poorly correlated with product quality because Fe may be in the form of goethite, hematite, or inside the crystalline structure of kaolinite. Thus, a more robust technique capable of distinguishing each mineral phase is desirable. Diffuse reflectance spectroscopy has been used to analyze iron oxide/hydroxide content both qualitatively (Torrent and Barrón, 2003; Liu et al., 2011) and quantitatively (Jiet al., 2002 and 2006). These authors correlate slopes and inflection points at characteristic absorption bands with oxide/hydroxide content in natural soils. The approach presented here involves the extensive use of the Kubelka-Munk (K-M) theory, which has been used for color matching (Schabbachet al., 2009 and 2011) and particle size determination (Otsuka, 2004) in a simplified version. Unfortunately, the scattering constant S is very difficult to measure for dry powders, because the equations require a thin layer of material. Attempts have been made (Gonçalves and Petter, 2007, and Gonçalves, 2009) but the experimental errors tend to be high. Thus, this paper aims to develop a tool for the quantification of contaminant minerals in kaolin based on the K-M theory without resorting to measurements over thin layers. This tool is based on a new two-constant approach, which takes into account differences in scattering between materials over the whole measured spectrum. The experimental dataset consists of the reflectance spectra of mixtures between a bleached kaolin and synthetic Fe pigments.

Feb 27, 2013

By John H. Raymer

Groundwater inflow into hard rock tunnels is strongly affected by recharge and drawdown of the water table. Previous analytical and empirical methods for estimating inflow have generally not accounted for these factors in an accurate or systematic way, resulting is wrong conclusions about inflow and the effects of the tunnel on the surrounding environment. This paper discusses these issues and provides some simple analytical equations to estimate inflow and water table drawdown around the tunnel. Examples from tunnels in the Atlanta area are provided.

Jan 1, 2005

By M. C. Fuerstenau

Collophane, cryptocrystalline fluor-apatite, is examined as a substrate for plant water and wastewater remediation. The attenuation of Fe3+, Fe2+, Hg2+, Pb2+, and Cd2+ is presented as a function of metal ion concentration, amount of collophane, initial pH and conditioning time. TCLP results for Pb2+contaminated collophane are presented. Mechanisms of adsorption for divalent and trivalent species are suggested.

Jan 1, 2001

By M. Santillan

Minerales Monclova S.A. de C.V. (MIMOSA) has applied different methane gas drainage technologies, according to the top industry requirements in order to keep the methane gas at the lowest possible concentration in our operations, both in the development sections and longwall sections. Our staff has used the horizontal rotary technique. In 2004 MIMOSA bought a re-built drill machine and signed a contract with Resource Enterprises Inc. (REI), which included a training program in Horizontal Directional Drilling using the reflex system. The training system was developed for a period of three months in Mine VII, with very good performance by the MIMOSA staff. After the training the equipment was moved to Esmeralda Mine, where we had already drilled holes at the development section, 2,500 ft. It was the longest distance that could be reached with our original equipment, obviously; the directional drilling program is another challenge for us and our staff, but we are very confident that our result will be better every time. We will be evaluating each borehole and expect to improve our results in each progressive borehole, until we can drill up to the capacity of the equipment. We are in the process of buying another drill with an electronic monitoring device (DD DMecca) in the following months.

Jan 1, 2009

By Paul D. Tomlingson

There are huge benefits for mining operations that have a well-defined maintenance program that is understood and followed across the total operation. But for operations lacking a quality maintenance program, there is equal assurance that nearly every major maintenance problem can be traced to this omission. Few problems will be permanently corrected until such a program is implemented. Definition The maintenance program re-quires the interaction of all mine departments. Initially, the production department will request work and the maintenance department will identify work, principally through preventive maintenance inspection and testing efforts. Maintenance will then classify the new work to determine the best way to respond. Maintenance will plan selected major jobs to enable its crews to carry them out more effectively. Maintenance will schedule the planned work with operations. Supervisors will assign all types of work to their crews then, control the work through effective supervision. As work is completed, maintenance will measure the work using an accurate information system. Next, it will assess overall accomplishments against goals such as performance standards or budgets. In addition, the pro-gram would prescribe a means to evaluate every aspect of the operation as it affects maintenance so that necessary improvements or changes can be identified, prioritized and acted on. Such evaluations should be part of a mine-wide continuous improvement effort. A well-defined maintenance program is one of the best investments a mining operation can make to assure its profitability. Educating the total operation on the pro-gram assures long-term dividends from the investment.

Jan 1, 2008

Based on X-ray phase analysis and exploratory experiments, a new technology was developed to recycle multiple valuable elements in spent Al2O3-based catalyst. The experimental results showed that after roasting at 750°C for 30 minutes at an Na2O:Al2O3 mol ratio of 1.2, the leaching recoveries of alumina, vanadium and molybdenum from the spent catalyst were 97.2%, 95.8% and 98.9%, respectively. Vanadium and molybdenum in sodium aluminate solution can be recovered by barium hydroxide and barium aluminate. The precipitation recovery of vanadium and molybdenum was 94.8% and 92.6%, respectively. Al(OH)3 is prepared from sodium aluminate solution using the carbonation decomposition process. The purity of Al2O3 is 99.9% after calcinations, and the recovery of alumina can reach 90.6% in the whole process. The Ni-Co concentrate was leached with sulfuric acid, and a nickel recovery of 98.2% and a cobalt recovery of more than 98.5% were obtained under the experimental condition of 30% (w/w) H2SO4, 80°C, a liquid: solid ratio of 8:1 (by weight), a reaction time of 4 hours and a stirring rate of 800 rpm.

Jan 1, 2007

By D. He

In China, the total reserves of vanadium, reported as V2O5, in stone coal is 118 Mt (130 million st). Recovering vanadium from such a large resource is very important to China?s vanadium industry. The technology now being used to recover vanadium from stone coal has the following two problems in the leaching process: a low recovery of vanadium and high acid consumption. To resolve these problems, a new leaching technology is proposed. The effects of factors such as H2SO4 concentration, liquid-solid ratio, temperature and time, and the types and additions of additives were studied. By adding 1.5% (by weight) CaF2 and leaching the roasted residue of stone coal with 5.4% (by weight) sulfuric acid at 90°C for 12 hours at a liquid-solid ratio of 2 mL/g, the leaching degree of vanadium reached 83.10%. This proposed leaching technology gives a feasible alternative for the processing of roasting residue of stone coal and can be applied in the comprehensive utilization of stone coal ores in China.

Jan 1, 2008

By Serge Moalli

The Ashlu Creek Hydro-electric project, located north of Squamish, BC, at the confluence of Ashlu Creek and the Squamish River, comprises a 49 MW run-of-river project and features a 4.08 m diameter, 4.4 km power tunnel and a 128 m deep drop shaft. The Ashlu Creek Hydro-electric project is being developed by Innergex under Ashlu Creek Investments Limited. Site civil works are being completed by Ledcor CMI of Vancouver with tunnel construction by Frontier Kemper Constructors ULC under a lump sum design-build contract. Site works got underway in September 2006 with the construction of the tunnel portal and laydown area. These site works required rock slope stabilization over a 50 m rock slope to secure the laydown area as well as the construction of a tail track muck tipping station and structural wall to facilitate TBM excavation and spoil removal. Starter tunnel construction commenced in early 2007 and TBM tunneling started in the late spring of 2007 and is planned to continue until early 2009. The power tunnel is being excavated using a 1,200 kW Wirth open-type hard rock TBM dressed with 31?17' cutters. The TBM featured two fixed mounted rock bolt drills behind the finger shield: these were removed and replaced with jacklegs to improve access. A probe drill at the end of the main beam is also present. The geology along the 4.4 km power tunnel comprises very strong and generally massive granitic bedrock with rock strength greater than 225 MPa. A unique feature of the project is that no subsurface investigations have been completed for the tunnel however extensive bedrock outcrops are present along the Ashlu Creek valley. A historical quarry exists approximately mid-way along the tunnel alignment that has exposed good quality granitic bedrock. TBM tunneling to date has achieved advance rates of 10?20 m/day with a maximum of 23 m and has encountered all of the anticipated six major fault zones where the installation of various standard high capacity tunnel support was successful to facilitate TBM advance through these sections.

In this paper, uniaxial compression tests were conducted on intact rocks and broken rocks that were reinforced by grouting, and the effects of grouting on the strength of broken rocks were analyzed. The results show that after grouting reinforcement, the bearing capacity of broken rocks with different lithologies increased, and their uniaxial compressive strength recovered by approximately 6%–16%. The results indicated that the stronger the rock, the smaller the strength recovery of the consolidated body formed after grouting. At the same time, using borehole camera observation and deep overburden strata separations, the fracture development characteristics of surrounding rocks of the gob-side retained entry were analyzed and divided into different regions. On this basis, a guided grouting method was proposed; that is, shallow hole grouting was first used in the plastic zone of the broken surrounding rocks to form the isolation layer, and then deep grouting holes were arranged in the elastic-plastic zone of the transition zone to guide the slurry flow to the shallow unfilled zone. Therefore, the broken surrounding rocks were reinforced into an integrated body and selfbearing capacity improved.

Jul 28, 2020

The development of technologies to improve mining and mineral processing is an ongoing process. These new technologies are the result of the industry’s drive to lower costs and improve productivity. Many technical conferences allow mining industry professionals to learn about these new technologies and possibly implement them in their own operations. In early November 2005, The 14th symposium on Mine Planning and Equipment Selection (MPES) was held in Banff, Alberta. It was jointly held with the Fifth International Conference on Computer Applications in the Minerals Industries (CAMI).

Jan 1, 2006

By A. Martin

Detailed porewater profiles of arsenic and other interstitial metabolites were used to assess the relationship between trophic status, sediment redox chemistry and arsenic mobility in a historic tailings repository. The results demonstrate that in eutrophied systems which exhibit greater sediment oxygen demand, the depth of the Fe(III) redoxcline, and hence depth of arsenic release, may lie in close proximity to the sediment-water interface. As a result, arsenic scavenging mechanisms are significantly reduced, resulting in a greater flux of arsenic to the water column. Such considerations have important implications for the management of pit lakes, tailings ponds and contaminated lakes which may consider: 1) the discharge of sewage to the water body during operations; and/or 2) post-closure fertilization as a remediation strategy.

Jan 1, 2002

By C. A. Young, J. D. Miller

Thermodynamic data has been obtained for oleate chemisorption at fluorite (CaF2) and calcite (CaCO3) surfaces using adsorption isotherms determined previously at room and elevated temperatures by in-situ Fourier transform infrared/internal reflection spectroscopy (FT-IR/IRS). Linear regression analysis was used to statistically derive free energy data as a function of temperature assuming oleate chemisorption followed Langmuir-type adsorption. Enthalpy and entropy changes were subsequently ascertained from the Clausius-Clapeyron equation and fundamental thermodynamic relationships. Essentially, no difference in the free energy of chemisorption at the two mineral surfaces was found; however, the differences in enthalpy and entropy values were significant. By comparison, the results showed that oleate chemisorption at fluorite surfaces was more extensive and more entropically driven due to more water being displaced. Results correlate well with values determined in the literature for other mineral collector systems. These findings help explain the greater hydrophobic character of fluorite than calcite in both the absence and presence of oleate.

Jan 1, 2002

By B. K. Belle

The beginning of 21st century has heralded the global strategic importance, as evidenced by increase in energy prices and energy generation-emission-utilization dilemmas. In January 2008, the South African energy supplier, ESKOM had tabled the concept of power conservation and acknowledged the energy crisis until 2016. The concept is required of all energy users to reduce their electricity consumption, intensify energy efficiency and cautiously proceed with new projects. The generation of energy results in by-products called ?green house gases? (GHGs). To make a positive response to climate change and their effect on the environment, every energy user must ensure efficient energy use through technical and administrative means referred to generally as energy savings. This paper identifies mine ventilation engineering, in particular the electricity consumed by main fan units, as an area of potential energy savings. For a major mining company, electricity consumed by main ventilation fans alone can be in the order of 120 MW. Although a known fan engineering technique but scantly applied technology identified as the Hermit Crab can be seen as a ?quick win? project, due to its success in other industries such as cement and steel. The ?Hermit Crab? technique® involves upgrading or replacement of an impeller - whatever its origin - with a design impeller to suit the actual ventilation requirements, resulting in increased fan efficiencies. The cash flow benefits associated with a case study and its rollout of this technology have been calculated. For a 10% increase in main fan efficiency, would have a net present benefit of US$ 16.08m over 10 years. With the inclusion of carbon credits, this benefit rises to US$ 29.40m in total. Application of other available technologies, viz., composite materials, ventilation-on-demand and variable speed drives are discussed.

Jan 1, 2009

By D. Bogunovic

The U.S. coal mining industry consumes a significant amount of energy, primarily diesel fuel and electricity. The continuous global increase in energy demand, high energy prices, and environmental issues related to carbon dioxide emission represent a substantial challenge for the mining industry. This paper presents a result of research work on development of an integrated data environment system for analysis and control of energy consumption in a surface coal mine. A case study on an operating surface coal mine is carried out to demonstrate the practical application of the developed system. The research work presented here may be used by mining professionals to help provide the answers to the crucial questions of when, where, and how much energy is being used. This developed system represents a framework for efficient management of energy consumption. Key words: surface mining, coal, energy consumption, Information System.

Jan 1, 2009

By H. C. Liang

Reverse osmosis (RO) and nanofiltration (NF) are widely regarded as being best available technologies (BATs) for removing contaminants of concern from water. In recent years, NF or RO treatment has increasingly gained more acceptance in the mining industry for treating mine water to remove a wide assortment of contaminants, either for meeting discharge standards or for internal re-use in mining processes. Consequently, the number of NF or RO membrane mine water treatment facilities has steadily increased. Although NF or RO membrane filtration can be a powerful tool in mine water treatment, especially when multiple contaminant removal is required, it also has many potential disadvantages. Besides the generally higher capital and operational costs for the high pressure membrane processes, organic constituents in mine water may foul the membranes, while inorganic compounds such as gypsum, calcite, or silica are liable to scale the expensive membranes if proper pre-treatment processes are not implemented. Additionally, because these membrane treatment processes generate a substantial reject or brine waste stream in addition to the clean treated water or permeate stream, brine management also needs to be considered carefully when deciding upon the viability of an NF or RO mine water treatment process. Because of these issues, it is important to conduct detailed analyses of the trade-off between selecting NF or RO vs. using chemical treatment processes when designing a mine water treatment facility.

Jan 1, 2012

By A. D. Davis

The former Homestake gold mine at Lead, South Dakota, has been selected by the National Science Foundation as the proposed host site for the Deep Underground Science and Engineering Laboratory. The deep laboratory and associated research campus will be developed at approximately the 7700-ft level. Plans also include the development of the Sanford Underground Science and Engineering Laboratory at the 4850-ft level. After the mine?s pumps were shut off in June, 2003, water levels rose to approximately the 4650-ft level by early 2008. Pumps in the 8150-ft deep mine were turned on again for dewatering in April, 2008. Instrumentation is being installed in the mine to measure water-level declines during pumping, for later analysis of permeability and related hydraulic properties of the formation. Pressure-sensitive transducers and data loggers will provide real-time information on water levels that will be available to interested parties. Quality of the water also will be monitored as it is pumped from the mine. I

Jan 1, 2009

By Wm. Ross Wayment, Innes P. Grantmyre

INTRODUCTION It has been recognized for some time that major changes in mining methods will be required in the near future. Two types of factors contribute to this need for change. Intrinsic factors include ground control problems associated with mining at increasing depths, noise, dust, toxic fumes, and logistics problems which arise from operation in a cyclical fashion. Extrinsic factors include competition for labor from industries offering safer and less difficult work, pressure for less impact on the environment, and changing economic and political conditions. The search for new mining methods has resulted in extensive research being carried out on such novel approaches as thermal fragmentation, high-pressure water jets, sonic drilling, microwave fragmentation, and laser cutting, among others. Joy Manufacturing Co. has elected to concentrate on impact breaking in stopes as a first generation continuous hard rock miner. IMPACT BREAKING Fragmentation techniques show a drop in specific energy as efficiency improves. Specific energy is the energy consumed per unit volume of rock removed and is affected by such variables as rock material properties, fragmentation method used, operator skill, tool design, etc. Mechanical fragmentation methods generally have specific energies much lower than that of the more novel methods. Table 1 shows impact breaking to have an efficiency exceeded only by that of drill and blast methods and it is this high efficiency which led Joy to impactors as the subject for research on potential mechanisms for continuous mining in hard rock.

Jan 1, 1976

By D. Tao

The reverse cationic flotation is the most widely utilized flotation method for concentrating iron ore. In such a process quartz is often floated with ether amines (R?O(CH2)3?NH2) partially neutralized with acetic acid. However, it is well known that the cationic flotation of hematite does not work well if a certain amount of slime is present in ore slurry. To improve flotation performance, starch is often added to the flotation feed to selectively flocculate and depress the iron minerals and sodium silicate is used to disperse the silica gangue. The present study was conducted to improve the flotation efficiency of iron ore flotation by use of a new type of depressant for clay and iron minerals, i.e., GP clay binder. It is postulated that the GP clay binder minimizes slime adsorption on quartz and hematite particles by agglomerating clay particles to reduce their surface area. It is further theorized that the clay binder helps depress hematite flotation due to its unique chelating ability to iron ion. The results from this study clearly show that the GP clay binder is an effective depressant in iron ore flotation. When it was used as a substitute for corn starch, it increased concentrate grade from 60.78% to 67.67% and increased iron recovery from 71.96% to 72.90%. The combined use of GP clay binder with corn starch produced even better flotation performance, increasing concentrate grade to 67.08% and iron recovery to 78.15% simultaneously. Key words: Clay Binder; Depressant; Iron Ore; Flotation.

Jan 1, 2009