Search Documents

By J. -G. Swanson

Dust control in longwall coal mining depends primarily on the prevention of dust at the source and secondarily on the suppression of airborne dust. One of the primary methods for the prevention of dust is the wetting of the coal face prior to extraction, which can be achieved with water spray systems installed on the shield supports. The spray droplets must travel across the airway to the longwall face, where high ventilation air speeds can entrain water droplets and prevent them from reaching the face thus minimizing the dust control at the source. Through an evaluation of spray plume characteristics in a wind tunnel, the droplet size and droplet drift behavior was determined. This drift behavior was examined by evaluating the spray plume concentration drop and the droplet size shift near the nozzle exit at varying air speeds. Based on these evaluations, CFD modeling was applied to simulate the spray behavior for varying geometries. These results led to the selection of appropriate spray nozzles capable of carrying water droplets to the face at higher air speeds, resulting in an adequate wetting of the coal face and reduced dust generation.

Jan 1, 2012

By Rick Frechette, Bryan Ulrich

Representatives from several mining operations in three western states left their mines behind for a day in February to discuss with their peers the issue of water. The event was Knight Piésold and Co.’s Roundtable 2007, held in Elko, NV. It was third such event put on by the company. The issue this year was site-wide water considerations.

Jan 1, 2007

By G. Luttrell

Coal preparation plants play an important role in modern society by providing high quality feeds for coal-fired utilities, industrial boilers and metallurgical coke facilities. Unfortunately, field data indicate that preparation plants are often not operated under optimum conditions, resulting in lower productivity and lost profits. In many cases, this shortcoming can be attributed to a failure by plant operators (i) to recognize the importance of correctly adjusting plant operating conditions to accommodate requirements dictated by coal sales agreements within different coal markets and (ii) to properly account for variations in product moisture with particle size across different plant circuits. This paper discusses the important influence of moisture constraints on preparation plant optimization and provides a case study to illustrate the potential gains that can be realized via proper understanding of plant moisture control.

Jan 1, 2009

By David Dardick

Tround International Inc. is developing rock excavation and drilling devices which utilize a simple patented mechanism for firing frangible projectiles. This system launches a salvo of three projectiles with every shot in automatic sequence. Studies conducted by Physics International Inc. have demonstrated that firing projectiles into hard rock such as granite creates fragmentation which is much faster and cheaper than conventional drilling and blasting. The Tround salvo approach enhances this further by a controlled stresswave interaction created by a slight time difference during impact of the individual projectiles. The University of Maryland is conducting additional studies to optimize these parameters.

Jan 1, 1981

Oil sands processing generates huge volumes of slurry, known as tailings, that is being stored in tailings ponds. The volume of produced tailings is a very important factor in oil sands surface mine planning, because the available area for dam construction is limited to the lease areas. On the other hand, oil sands operators cannot leave mine sites without reclaiming the tailings ponds. Since most of the reclamation material is generated in either oil sands mining or processing, it is reasonable to include reclamation material requirement as part of long-term mine planning. In this paper, an integrated optimization framework is proposed to maximize the net present value (NPV) of the produced oil sands, with respect to tailings capacity constraints and reclamation material requirements. A mixed integer linear programming (MILP) model is developed to find the optimal solution for long-term mine planning problem. A sample bitumen processing flow sheet is used to formulate the volume of produced tailings, based on Clark hot water extraction method. To verify the proposed model, it is coded in Matlab and run using CPLEX. Run results for real-case oil sands dataset show that the optimal production schedule meets material requirements for reclamation, tailings volume is within tailings capacity range in all periods and the production schedule follows the predetermined horizontal direction.

Feb 27, 2013

By M. Javier

Defining the concept of sustainability is an important step for industry and society. It is necessary in order to clarify what it means when debunking the many misinterpretations pervasive in different levels of anthropogenic activities. Essentially, the extractive industry has a harvest of differences. Mining involves the extraction of natural resources which are finite, exhaustible, non-renewable, unsustainable, and pay only once. It is remarkable that the definition of sustainability that we will shortly arrive at has totally different characteristics from the definition accepted throughout society. We categorize nature as having its own destiny which is controlled by its own rules and principles and its own society, and is part of nature; therefore, society depends on nature and not vice versa as the initial focus. To society there are no conditions to humanize nature but only respect nature?s rules. It was a challenge to find simplicity for this task not only for the definition but also for the explanation of this concept specifically, to answer the question, ?what is the true meaning of sustainability?? Finally, we are also able through this definition to provide fuel for wide discussions and stimulate critical thinking to improve such a concept. As a result, we present this definition as the tool for society today and for future generations.

Jan 1, 2012

The fundamental objective of mine plans are usually to maximize the mine profit by extracting ore at the lowest possible cost over the mine life while some technical constraints are satisfied. Since the costs associated with the operation of trucks and shovels as resources are significant, determining the optimum number and allocation of these resources is an essential issue. This paper presents a Mixed Integer Linear Programming (MILP) model to determine the optimum number of shovels and trucks required to meet the short-term plan?s goals. Also, the model takes into account the allocation of trucks and shovels to mining faces. This model minimizes operational costs, while attempting to meet the production demand and to satisfy technological constraints. This paper also analyzes the operations of trucks and shovels in an open pit mine using ARENA simulation software.

Jan 1, 2012

By K. L. Lownie

For research and test data to serve a useful purpose, it is essential that it be derived from some known standard test procedure that allows for comparative analysis as well as independent replication and verification. Fan performance data provided by manufacturers is not absolute, and is influenced by the geometry of the test installation. For these reasons, fan test standards have been prepared in order to establish a clearly defined test procedure that allows for comparison of different fan designs, and also allows for the independent verification of test data. Internationally recognized Standards such as BS848, ISO5801, and AMCA 210 etc. are highly prescriptive, and precisely specify test duct configurations, measurement procedures, measurement planes and instrumentation to be used. Provided the laboratory tests are conducted strictly in accordance with the relevant Standard, the performance data will accurately reflect fan performance within the appropriate tolerances for efficiency, pressure and flow when tested in the defined configuration. Major differences in performance exist between a fan tested in accordance with a Fan Test Standard, and an identical fan installed in a mine ventilation system. The aerodynamic performance of any fan will be influenced by the quality of the fan manufacture, the flow system within which it is operating, the location of measurement planes, and the system stability. The flow distributions present in a standardized Laboratory test are unlikely to be repeated in mine ventilation systems, and this will also disadvantage fan performance. Unless the fan supplier takes all of these influences into account, there will an inevitable reduction in fan aerodynamic performance, and the end user will experience a shortfall in expected flow through the mine. The effect on fan performance can range from minor inconvenience to catastrophic fan failure resulting in major rectification costs and significant loss of mine production.

Jan 1, 2009

By K. Mondal

A macroscopic approach integrated with microscopic analyses for wettability characterization is presented. Wetting depends on 1) Contact between the dust and the fluid droplets, 2) Wettability of the particles by the wetting fluid, and 3) Wettability rate (due to low contact times). The goal of this paper is to show that the wetting rate is a significant factor in dust control. Samples from the roof, three different horizons of the coal seam and the floor were pulverized to less than 25 µm. Experiments were conducted with known wetting fluids to correlate surface tension and equilibrium wettability. Further analyses were performed in terms of surface charge (zeta potential), particle size, mineral composition, elemental composition, and quartz content. The surface tension reduction was also achieved by the use of chemicals and/or altering the temperature of the water. Two methods were used to evaluate wettability rates: a) near real-time comparison of wettability rates, and b) comprehensive evaluation of the intrinsic wettability rates. The data obtained provides meaningful insights towards the design of engineering controls for an economical solution to dust control in coal mines.

Jan 1, 2012

In the dimension stone industry, workers in processing shops may be exposed to harmful levels of respirable silica dust when conducting the different tasks in stone preparation, which include cutting, grinding, polishing, and thermaling. To protect workers from this health hazard, operators sometimes ventilate processing shops using fan-powered dust collectors to capture and filter dust. To investigate this issue, NIOSH, Pittsburgh Research Laboratory, in cooperation with a dimension stone operation, upgraded an off-the-shelf dust collector the operator was utilizing in a polishing/cutting shop. Initial dust surveys showed that the unit was under-designed for the amount of dust being generated in the shop. The objective of the research was to cost-effectively increase the air cleaning volume and improve dust capture efficiency of the unit with a larger motor and blower. The unit?s original stock 0.56 kw motor and blower was replaced with a 2.24 kw motor and matching blower to increase airflow. The unit was evaluated both in the laboratory and the shop before and after the retrofit to determine the improvement of the upgrade. The study showed that the 2.24 kw upgrade improved the performance over the original 0.56 kw motor resulting in more dust being cleaned from the ambient air in the shop. The 2.24 kw unit cleaned 19% more air and captured 32% more respirable dust than the 0.56 kw unit.

Jan 1, 2009

By H. Arima, T. Fujita, W. Yen

The copper catalyzed gold oxidation and reduction mechanisms in ammonium thiosulfate solution were investigated by Eh-pH diagram based on the optimum reagent combination for 60 mass% -75 µm silicate ore at 16g/t Au with the maximum gold extraction of 92% and the minimum ammonium thiosulfate consumption of 23 kg/t-ore for 24 hour’s leaching at ambient temperature. The gold recovery by cementation was nearly 100% by Zn and Al powders at Metal/Au mass ratio of 30, and around 95% by Cu powder at Cu/Au+ mass ratio of 50. In order to oxidize the gold efficiently with the less thiosulfate consumption, the stable region of [Cu(NH3)4]2+ should be as wide as possible in the region, where [Cu(S2O3)2]3- was more stable than [Cu(NH3)2]+. In order to reduce gold from the pregnant solution with the less metal powder’s (Zn, Cu, Al) consumption, the stable region of [Cu(S2O3)2]3- should be wider than [Cu(NH3)2]+ on copper precipitation. Zinc powder may recover gold more efficiently than copper powder with the similar trend on the effect of ammonia, copper and thiosulfate. However, the large amount of copper will be co-precipitated along with gold since the stability of zinc ammine and thiosulfate complexes are higher than that of copper’s. Aluminium may reduce gold efficiently at higher thiosulfate concentration and pH. These results were confirmed and compared with the optimum reagent combination for finer grind sample at 100 mass% -75 µm, which is the optimum ore size for the standard cyanidation at 1.0 g/ l NaCN to obtain about 95% gold extraction. The optimum reagent combination was concluded as 0.5 mol/l NH4OH, 0.0001 mol/l CuSO4*5H2O and 0.05 mol/l (NH4)2S2O3 with the result of 94% gold extraction and 3kg/t-ore of ammonium thiosulfate consumption. Gold and copper stabilities were well agreed with the result of coarser grind ore thermodynamically. The lower reagent combination will reduce gold oxidation power, but significantly minimize the reagent consumption. From this pregnant solution, nearly 100% of gold was successfully recovered by zinc precipitation at Zn/Au+ mass ratio of 30. Aluminium and copper precipitations resulted in less than 40% of gold recovery at Metal/Gold mass ratio of 30. The reagent consumption cost on this lower reagent combination followed by zinc precipitation was $1.6/t-ore, while the cyanidation was $3.1/t-ore. Thiosulfate oxidation mechanism indicated the similarity to Belousov-Zhabotinsky reaction.

Jan 1, 2002

By M. Javier

Mining, waste is growing problem both physical accumulation and increasing toxic uncertainties it presents in the long run. Its value ?zero? is strictly calculated by economy. This mining model begs the question: What is the value of waste & what does it represent to the mining industry? Waste is widely accepted as a ?by product? generated as a consequences of the mining process. The abundant waste accumulation affects society, as receptor, in many ways and the waste piles of materials has no use and no destiny. In reality, this waste is monument of imperfection of the extractive industries worldwide. Our planet is finite and has strict limitations, which mining has traditionally ignored. It is time to design a new system, in which clearly, waste design must be integrated in whole mining process; it has no room to postpone. This paper presents a concept in waste design by which toxic mining waste not only can be rendered inert but also act as nutrient to help balance the ecosystems. This concept calls for extractive industries to pursue EQUILIBRIUM with nature (Geomimic). Also, this concept offers countless gains and opportunities fro the industry and by converting liabilities into assets; mining engineers become the managers and stewards of nature. Also, waste design offers new solutions for proper and sustainable waste management of the mining industry.

Jan 1, 2011

By D. Pappas

Over the past decade the number of contractors working in underground coal mines has nearly doubled; however, the effect this has had on the industry?s injury rates has been the subject of much speculation. The confusion exists because the U.S. Mine Safety and Health Administration (MSHA) database does not assign contractor hours to the individual mining operations where they worked. To better understand the safety record of the contractor segment of the industry, the National Institute for Occupational Safety and Health (NIOSH) undertook a comprehensive analysis of the data contained in the MSHA database. The first part of the study compared overall contractor and operator trends from 1983 to 2009 related to employment, hours worked, injury rate, and days lost. One unexpected finding was that the larger contractors tended to have higher injury rates than the smaller ones. The second part of the study directly addressed the role of contractors on the safety record of 10 large underground coal mines. A detailed analysis provided both injuries and estimated contractor hours worked at these mines for the period 1992?2007. Comparison between the estimated contractor injury rates and the reported operator injury rates at these mines indicated that the contractor injury rates were significantly higher at most of the operations studied. However, the industry-wide data indicates that contractor and operator injury rates have converged since 2005 and are now equivalent.

Jan 1, 2011

By M. Buxton

Sensor derived data can add value across the mining operating chain ranging from resource definition, extraction, pre ? concentration, mineral process monitoring and assessment of product quality. Most documented studies on the use of sensors in mining focus on specific technologies for specific applications. These studies do not take into account different aims, objectives and operating conditions at different steps in the value chain. The first part of this contribution assesses key physical performance and discriminatory requirements of sensors applied in each portion of the mining value chain. The second part proposes a framework of methods for quantifying the value added by additional sensor information. Integrating the sensor based technology and the economic value quantification allows for both, designing an economically optimal sensor monitoring network along the whole mining value chain and optimizing efficiencies. Illustrative studies demonstrate the significant economic benefits, in particular in reduction of exploration expenditures, increase in extraction efficiencies, increase in ore product quality and improvement of processing efficiencies.

Feb 27, 2013

By A. D. Davis

Limestone-based technology for arsenic removal from water is an innovative and promising method. The technology offers the potential for low-cost disposal of a stable waste product after arsenic removal, either in an ordinary landfill or by encapsulation in concrete. Leaching research described in this paper shows that the limestone waste, after encapsulation in concrete, passes the Toxicity Characteristic Leaching Procedure (TCLP) test. Leaching was less than 0.05 mg/L, which is 1/100 of the U.S. EPA?s standard for disposal of arsenic in a landfill. Disposal of arsenic-enriched waste is critical for commercial viability of arsenic-removal technologies. Low-cost disposal gives the limestone-based method an advantage that could help communities meet the new maximum contaminant level of 10 parts per billion for arsenic in drinking water. The ability to recycle the waste material in concrete could add a significant economic benefit, further reducing overall costs.

Jan 1, 2009

By L. W. Berry

Drill and blast planning is critical to successful mine production, both in timing and in results. However, typical planning, reporting, and information exchange usually involves large quantities of data collated in a discordant set of spreadsheets, databases, and reports. Collecting, analyzing, modeling, and distributing all data necessary for efficient drill and blast operations is time consuming and cumbersome. MineSight Axis Drill and Blast provides an extensible core of functions, seamlessly integrated with other MineSight software tools, to make sense of this information. The benefits of improving the management of drilling and blasting processes are immense and result in improved fragmentation at a lower cost, improved shovel and truck productivity, and enhanced ore processing.

Jan 1, 2011

By R. C. Milici

Historical production data and reserve decline rates can be used both to predict future coal production rates and to estimate when the reserve will be depleted. Reserve estimates inferred herein from historical production data and decline rates are commonly lower than estimates made from geologic data. The latter include significant amounts of lower quality (deeper, thinner, higher sub) coal which may be mined when the better deposits are depleted.

Feb 24, 1997

By Lee W. Abramson

Performing risk analyses on tunnel projects has become common place and on many projects it is required from an owner or regulatory perspective. After the project is planned, designed and constructed, the data concerning identified risks, assumptions, costs, probabilities and mitigations is generally long forgotten and buried in some file somewhere. A study was performed comparing predicted risks versus actual events on several recently constructed tunnel projects. Probabilities and costs for selectively common risks on tunnel projects have been studied and re-evaluated. Conclusions are presented that can guide future projects and the veracity of the tunnel risk analyses performed.

By George Watson, Gu Quanzhong, S. Gerard Sawyer

Bulkheads, also known as hydraulic seals, are used to seal abandoned workings and protect adjacent active mines from explosion and control unwanted inflows of water from poorly sealed shafts, water-bearing strata, and abandoned mine areas or gobs (1). At coal seam outcrops, bulkheads have typically been used to prevent access and to control acid mine drainage. Bulkheads have also been installed at outcrop openings located within the footprint of an embankment dam, or within the reservoir of an impoundment, to prevent stored water or slurry waste from flowing into active or inactive underground mine workings (2). Components of MICON Bulkhead Seal MICON bulkhead seals in mining applications refer to seals designed to impound liquids or slurry. The MICON bulkhead seal is comprised of two concrete block walls set in the front and back and a polyurethane/aggregate core (Figure 1). The two walls are usually dry-stacked, surface-bonded walls constructed with solid load-bearing concrete blocks (ASTM C90) or concrete building brick (ASTM C55). The surface bonding material used in the wall construction must be MSHA-approved. The type of stone, if any, used to fill the space between the walls is not essential. However, MICON generally uses No. 57 limestone in 50 lb. bags, specified to moisture control, shrink-wrapped and palletized. The polyurethane foam used in the construction of the bulkhead seal is engineering specified and formulated by density based on the optimization of cost, seal core thickness, required adhesive strength, the use of stone filler and other required physical properties.

Jan 1, 2005

By M. J. Fairweather, J. R. Egan, W. A. Meekel

Cominco Metals, in cooperation with two Canadian Universities and the Government of Canada, is developing applications for column flotation in the treatment of lead and zinc ores. Plant scale results at Polaris and pilot plant studies of Sullivan, Pine Point and Red Dog ores show column flotation to have significant advantages over conventional mechanical flotation for lead and zinc cleaning. Results from these ongoing studies are discussed in relation to ore texture, mineral recovery, impurity behaviour, scale-up and control.

Jan 1, 1988