Search Documents

By k. Lebecki, S. Trzcionka

The prototype and test results of the instrument for quick determination of incombustible content in deposited dust as a protection against coal dust explosion propagation are presented. Presently existing methods do not permit to obtain quick information about incombustible content, needed for the proper protection of workings. As the operating principle for the e instrument the dependence of reflection of infrared radiation intensity on incombustible content in the sample is chosen. The construction is based on the modern electronics. The measurement will be done at the sampling site. The range of the instrument is 0-100% of incombustible, direct reading, autonomous supply, weight no more than 0.5 kg, and is intrinsically safe according to EN Standards. During the Conference the instrument will be commercialized.

Jan 1, 2003

By F. T. Cawood

This paper reviews the Mineral and Petroleum Resources Royalty Bill of 2006, identifies potential areas that require further consideration by the National Treasury and, where appropriate, offers alternatives. At its basic level a royalty regime consists of two elements: the base and the rate that must be applied to the base. Deciding on an acceptable royalty rate is a complex matter and can be done only after extensive analysis of all variables affecting the competitiveness of the regime. The proposed royalty rates are in the range of zero to five per cent and are based on sales revenue. It is argued that future investment patterns are more likely to be influenced by market cycles and commodity prices than policy events. Inevitably the current boom in the minerals sector will come to an end and the success of the proposed regime will be known only when profit margins are under pressure. Policy makers must therefore have the long run in mind when developing policies that affect the ability of industry to do business, without the need to renegotiate each time there is a change in the market. A long-run policy must be sufficiently flexible to allow for consistently fair sharing ratios and splitting of revenues between government and industry. Although broadly in line with international practice, the current version cannot be regarded as internationally competitive and efficient. In order for the royalty bill to become internationally competitive, promote beneficiation of mineral production and adequately compensate the State for the loss of a national resource, the National Treasury should heed the following main recommendations in this review: 1. Abandon the notion that each mineral product must have its own royalty rate; 2. Introduce an NSR type royalty that allows for value-addition costs to be deducted from the base; and 3. Provide for automatic relief through the use of a sliding-scale mechanism based on ability to pay, e.g. the X-Factor used in the gold mining tax formula.

Jan 1, 2007

By C. Kliem

Geological, tectonic, geochemical and geophysical data were utilized for the mineral resource assessment of the Biga Peninsula in NW Turkey. During the deductive phase of the project multivariate statistical methods were applied to accentuate characteristic parameters which sufficiently describe the different types of Pb - Zn mineralization. The parameters most likely to be indicative of mineral occurrences were determined. In the following prognostic phase these parameters were further statistically treated to determine favourability indexes for the occurrence of a deposit within each cell of the training area. Preliminary results of probabilistic, univariate and multivariate methods are presented.

Jan 1, 1987

By R. G. B. Pickering, H. H. Haase

CONTRIBUTION BY D. O'CONNOR Mechanical extraction of rock has been a goal sought after for some decades in the South African gold-mining industry. There are factors distinct from the mode of mechanical extraction that may have considerable influence on its prospects for extensive adoption; the rockburst factor is one of these. REPLY BY H.H. HAASE AND R.G.B PICKERING We agree with Professor O'Connor that, in conventional gold-mining operations, a disproportionate number of seismic events occur in the period immediately following a blast; rockburst activity follows the same pattern, and it has been calculated that, if the rockburst peak were spread evenly across the day, the rockburst exposure of stope workers would nearly double.

Jan 1, 1992

By A. Mehmet

The feasibility of employing a multi-stage column for the recovery of gold from cyanided pulps using extruded carbon was investigated on a pilot-plant scale. It was anticipated that the column contactor would have certain advantages over conventional carbon-in-pulp plants. The feed pulp was screened to remove particles larger than 200 µm and was diluted to a solids concentration of about 23 per cent. The column was operated continuously for 24 days at a pulp flowrate of about 60 l/min and a carbon flowrate of 44 litres per day. The average gold concentrations in the barren pulp 12 hours and 24 hours after the carbon transfer were 0,012 and 0,031 mg/l respectively. The average gold concentration in the solution phase in the feed was about 2,0 mg/L. The average gold Loading on the carbon was 6290 g/t. Calcium carbonate was removed from the loaded carbon by treatment with 0,5 bed volumes of 2,8 per cent hydrochloric acid solution at ambient temperature. The calcium concentration was reduced from about 17 000 to about 500 g/t The carbon was eluted by the Zadra procedure at atmospheric pressure. The results of the elution were highly satisfactory, the gold concentration being reduced from about 6000 to about 20 g/t in 48 hours. The eluted carbon was regenerated in a Rintoul kiln at about 700°C. The activity of the regenerated carbon was found to be at least as high as that of fresh carbon.

Jan 1, 1992

By E. Minnaar, P. J. Cilliers, M. Bellino, L. M. Roux, R. Dye

The classic technique to remove impurities in a cobalt stream is selective precipitation. This is usually followed by re-leaching to produce an advanced electrolyte for cobalt electrowinning. Although this technique ensures an adequate cobalt concentration in the electrowinning circuit, some of the consequences include unwanted losses through the numerous selective precipitation steps resulting in lower recoveries. One plant that currently utilizes selective precipitation is the Luilu Metallurgical Plant (Luilu) in the Democratic Republic of the Congo. This paper evaluates the benefits of using solvent extraction technology as a purification step in the Luilu Process with the aim of further increasing the overall cobalt recovery and to ensure that a suitable cobalt concentration in the advanced electrolyte is achieved. The implementation of a solvent extraction-electrowinning process is found to be beneficial in terms of achieving improved recoveries and cobalt cathode quality, however there are many other factors that impact the success of converting from the classic precipitation process used at Luilu.

Jan 1, 2007

By L. A. Vermeulen, D. D. Howat

A study was made of the performance of a rod mil operating without liter bars and with different arrangements of liter bars in the lining. . The results show that striking improvements in performance, increased throughput, and reduced consumption of liner metal and electrical energy can be obtained by a change in the geometry of the liter-bar arrangements within a mil. Rod mils of equal size fitted with the same arrangement of liter bars but operating at different speeds presented apparent anomalies in the relative consumption efficiency of electrical energy for the production of material smaller than 75 µ m. Marked savings in the consumption of liner metal were achieved by the use of an arrangement of alternating lines of higher and lower liter bars. A study of the relative performances of two large tube mils showed that the use of liter bars in one of the mils resulted in a marked reduction in the consumption of liner metal and electrical energy per ton of material smaller than 75 µ m in the product.

Jan 1, 1986

By D. G. Krige

D. G. Krige: The stimulating contributions from Messrs Cooke, Curtis, Martus, Johnston, Van Wyk, Van Rensburg and Wroth are appreciated by the author and provide clear evidence of the importance not only of the principle of assistance to gold mines, but also of its scope and form. In general all the arguments, raised by Messrs Cooke, Martus and Johnston in favour of extending the scope of the new assistance scheme can be accepted as sound.

By D. E. Sweeney

In May of 1980, a mine operated by Belmoral Mines Ltd experienced a failed crown pillar, resulting in the death of eight miners and putting sixteen others in harm?s way. The Ferderber mine was located in the Val d?Or region of the province of Quebec in Canada, and had been under development for 19 months and production for 9 months, since the opening of the portal. The crown pillar separating the 1?7 level from overlying overburden ultimately failed, permitting an estimated 1.5 million cubic feet of liquefied sediment to gain entry into the mine. This paper back-analyses the cave-in by applying decision error theory, in an examination of the organizational culture and the collective decisions contributing to the cave-in disaster. A case will be made for a greater understanding of mining methodology, geomechanics and risk assessment when operating in such challenging geologic conditions. Boundary condition and decision (BCD) analysis will be introduced as an innovative new method for the analysis of mine accidents and incidents. It will also be shown that BCD analysis can be applied to any event in an enterprise for which standards, norms or legislation exists. A cognitive profile will be presented that provides insight into the safety ethos existing within the Ferderber mine organization at the time of the tragedy.

Jan 1, 2007

By A. J. Roets

Despite its growth over the years, necessitating ever¬larger office accommodation, the Gold Fields group changed its head office address in Johannesburg only twice in 94 years. The first move was at the turn of the century, from the then select suburb of Doornfontein to the corner of Fox and Simmonds Streets. The second move was in the thirties, from that address-now the Reserve Bank building-to the well-known address of 75 Fox Street. With the advent of the first mines of the West Wits Line by the end of the thirties, 75 Fox Street proved too small, and the eastern section of the Commissioner Street side of the present head office was added on. In the fifties, when space once more became a serious problem, the old Exploration building was purchased and demolished, and the present west wing on Commissioner Street was built on the site. In the early seventies, cramped conditions again made life difficult and, despite a reorganization of the interior layouts, the need for expansion remained critical. Eventually, the adjacent Hollard Place and parking area became available, and plans for an extended new building complex could he considered. The building project was

Jan 1, 1985

Notices TRANSPORTATION AND THE ENVIRO NMENT The 5th Quinquennial Convention of the S.A. Institution of Civil Engineers will take place at the Carlton Centre, Johannesburg, from 20th to 24th August, 1973. ENVIRONMENTAL ENGINEERING A conference on environmental engineering problems in industrialized and developing countries is to be held at the United Engineering Centre, New York, on 19th and 20th September, 1973. RABCEWICZ-COLLOQUY The Austrian Society for Geomechanics is to honour Professor Ladislaus V. Rabcewicz, on the occasion of his 80th birthday, with a meeting in Salzburg Congress Hall on 11th and 12th October, 1973. The themes of the four half-day sessions will be as follows. PYRO MET ALL URG ICAL EVENTS IN 1974 Diisseldorf is to be the venue for the following three events: International Iron and Steel Congress O.F.S. Branch Welkom THE MARCH GENERAL MEETING OF THE BRANCH WAS HELD IN THE ST. HELENA CLUB AT 8.00 P.M. ON TUESDAY, 6TH MARCH, 1973 O.F.S. Branch Welkom MINUTES OF A GENERAL MEETING HELD IN THE ST. HELENA CLUB ON WEDNESDAY, 16TH MAY, 1973, AT 8.00 P.M.

By J. H. Selby

The Southern African Institute of Mining and Metallurgy hosted the 6thInternational Heavy Minerals Conference at the Zulu Nyala Game Lodge near Hluhluwe in Zululand, during September 2007. This series of conferences has run for 10 years and has been held on three continents. The interest that has been shown in the conference over the years has demonstrated that the field of heavy minerals is a dynamic and profitable one. It is perhaps appropriate that the tenth conference was held in Zululand, South Africa, where it had its roots. The conference theme was ?back to basics?, and this implied revisiting many of the technologies that made this industry a great one. In doing so, we got a view of how those basic technologies have been put to new applications. There were 39papers accepted for the conference, covering all aspects of the industry. These were presented over a period of four days. This edition of the Conference Proceedings provides the reader with a permanent record of these papers. We hope this volume will join the other five, which this series of conferences has produced, and give a lasting record of the development of our industry.

Jan 1, 2007

By J. L. Porter

This paper takes a personal look, through the author?s own experiences, at the implementation of innovations in the narrow-seam, hard-rock mining environment of South Africa?s mining industry over the past 40 years. A number of examples are used to illustrate some of the successes and failures over this period. More importantly, the examples are used to illustrate that the bulk of the investment for these projects should have been applied in a manner that could have achieved more sustainable results. The use of the word ?technology? in this context is also examined, as it is the author?s contention that only measuring the performance of machinery fails to encapsulate the potential of the entire system describing the scope of the innovation being implemented. These experiences and observations are projected onto the current backdrop of upheaval in the relationship between key industry stakeholders and the sustainability challenges facing areas of the mining sector in the South African economy. The paper concludes with some opinions on where attention can be focused in order to develop new thinking that can be applied for the safe and economic extraction of the nation?s mineral wealth.

Jan 1, 2014

By E. J. Walls, W. C. Joughin

"In selecting a suitable method to sink a vertical shaft for underground access, a number of constraints influence the ultimate decision of where and how to develop the shaft, not least among these being safety, development and construction time, and cost. Two additional considerations stand out: these being geotechnical conditions and technology, the latter taking into account existing underground access. Assuming a project for which an existing underground excavation is available, it is tempting to build a shaft sinking project from the outset based on the raiseboring method, which has the potential to be the safest, fastest, and least expensive method provided that geotechnical conditions permit.And therein lies the rub: regardless of project time or cost constraints, when it comes to raiseboring a long (say, greater than 500 m), large diameter (greater than 4.5 m) shaft, the rock mass conditions ultimately dictate what method of shaft sinking will be feasible. Over the course of several studies for a particular project, several geotechnical analyses were carried out specifically for the purpose of developing a shaft by raiseboring. Risk analysis and experience showed that where the rock mass conditions indicated an unacceptably high risk potential, an alternative method needed to be considered, even if this meant increasing both the time and financial requirements.In this paper we present an overview of geotechnical investigation practices for shaft sinking. Decisionmaking thresholds for raiseboring or other methods of shaft sinking are discussed, including probabilities of failure, empirical rock mass classification, basic wedge failure, and back-analysis of a failed case. The design of appropriate support, and analysis of relative safety benefits for various shaft sinking methods, falls outside the scope of this work, and will be presented in a separate paper.IntroductionThe potential for rock mass failure during shaft development and construction affects whether a project is completed safely, on time and on budget. During the course of several studies to establish ventilation shafts for an underground expansion project, geotechnical analyses of rock mass stability and failure potential were carried out. The investigations were guided by the method of McCracken and Stacey (1989) together with insights from Peck and associates (Peck, 2000; Peck and Lee, 2007, 2008; Peck, Coombes, and Lee, 2011)."

Apr 1, 2019

By C. Mueller

Automation of mining operations is pushed by cost pressure and cyclical product prices. However, until now the different types of equipment were not able to communicate electronically with each other or with central computer systems. Therefore, the International Rock Excavation Data Exchange Standard (IREDES) was launched by major players in the industry. The task of this initiative is to define a ‘common electronic language’ for easy and standardized data exchange. As in other industries, this standard is expected to have significant impact on the use of automation in general and on the markets for third party components and software. The standard’s technical architecture is open and flexible for future applications. It consists of an ‘horizontal’ structure defining ‘Application Profiles’ for different types of data sets. An additional ‘vertical’ structure (‘Equipment Profiles’) implements equipment dependent definitions for each of the applicable Application Profiles. First profiles will be available for Drill Rigs. The standard bases on the XML language thus enabling easy data exchange with commercial databases. IREDES data sets may use storage media as well as networking infrastructures for information exchange. The IREDES work is carried out by the initiative members working jointly together in the IREDES work groups. It is open for participation of all interested organizations. First prototyping applications are expected to start during 2001, the first products may be available in the following year. Key words: Mine Automation; Machine Automation; Data Exchange; Rock Excavation; Standard; Remote Control; Teleoperation; Ethernet; TCP/IP; Internet Technology; Service; Quality Assurance; Control Centre;

Sep 1, 2001

By S. Ramatsoma, D. N. C. Phillpotts, B. Whitehead

Changes in flotation performance have been correlated to changes in froth structure, velocity and stability. Literature has shown that when the aeration rate is varied for a specific float cell, the recovery of the valuable mineral reaches a peak which also coincides with a peak in the air recovery – a measure of froth stability. Peak air recovery optimisation methodology is a way to use direct readings of physical phenomena by froth cameras to optimise the metallurgical performance of a flotation plant. The aim of this paper is to show the transient nature of the peak air recovery value and the variety of conditions required to attain the peak air recovery on an industrial flotation plant with tight base-layer control of the feed and internal conditions. Industrial site tests that were conducted under controlled conditions showed different peak values at significantly different corresponding aeration rates during normal operation. The measured peak air recovery points corresponded to maximum PGM recovery during normal flotation, as expected. This dynamic nature of the peak air recovery point conditions has not previously been discussed in literature and indicates the need for online measuring equipment and informs the design of process control algorithms required to exploit the phenomenon for optimisation. Keywords: Froth flotation, flotation control, flotation optimisation, peak air recovery

Jan 1, 2020

By L. A. Vermeulen, D. D. Howat

New distribution functions are derived to describe the size distribution of grinding elements in ball mils. The formulations are based on the assumption that abrasive as well as impactive interactions occur during bal milling-an assumption that is supported by a large body of experimental evidence. It is shown that the functions can be used in the estimation of the magnitudes of abrasive and impactive components in the total rate of bal wear. The relative magnitudes of the wear components provide a basis for optimization of the chemical and metallurgical properties of the balls in a given milling situation. However, it is contended that these quantities are also useful indicators of the relative intensities of the abrasive and impactive interactions that are operative in the size reduction of mineral particles within ball mils. These quantities can be determined for any industrial ball mil, and their magnitudes provide practical guidelines for mil operation. The theory is used in an analysis of samples of ball charges from two industrial ball mils, and it is also applied to al the data on bal-size distributions found in the literature. The qualitative correlation between the calculated values of the wear components and the reported operating conditions is good for a variety of industrial ball mils, in conformity with the hypothesis that the relative magnitudes of the wear components are related to the milling conditions.

Jan 1, 1986

By Nelson Sánchez

The Los Bronces Development Project (LBDP) was approved in October 2007 by the Anglo American plc Board at a capital cost of some US$1.74B, and is scheduled to be completed by the end of 2010. The project represents a big step forward for the Los Bronces mine since it will increase the treatment rate by 140%, the mining rate by 64% and almost double copper production during the first four years of the project. This economy of scale will also position Los Bronces as a much bigger and efficient mining operation, better prepared to face adverse market scenarios and allowing Anglo to consolidate its position in base metals. The project addressed numerous scope alternatives such as plant capacity vs mine capacity, cut-off grade strategy to maximise value based on the existing flotation and leaching process, cutback strategy, etc. Main infrastructure aspects of the project are as follows: ?Dump area with 2400Mt capacity for waste and low grade material ?Mining equipment: 1 x electric shovel, 12 x 300t trucks, 1 x drill ?Primary crusher: 60? x 89? ?Three new power lines (144MW capacity) ?Grinding plant at 87kt/day nominal capacity (includes a 4.3km tunnel with a regenerative conveyor belt) ?Grinding plant: 1 SAG mill 40? x 25?, 2 ball mills ?Slurry pipeline (52 km from grinding to flotation plant) with five choke stations ?Flotation plant (rougher, cleaning, regrinding circuits and molybdenum flotation). The history of Los Bronces started in 1867 when it was discovered. In 1978 ENAMI (Government company) sold Los Bronces to Exxon for US$112M. The same year a snow avalanche destroyed San Francisco Flotation Plant. In 1979 the plant was rebuilt at 4.9kt/day and from 1979 to 2002 several plant expansions were made up to 54kt/day capacity. In 2002 Anglo acquired Los Bronces for US$1.3B. The 2002 resource and reserve statement showed reserves at 459Mt at 1.02%CuT and resources at 780Mt at 0.80%CuT. The 2007 statement shows reserves at 1,480Mt at 0.67%CuT and resources at 1,644Mt at 0.45%CuT. Defining the size of a plant expansion is the key challenge that any expansionary project faces. The scope of this paper is a general review of the project, describing all the mining techniques that were used to define the best options that maximise value. In this context, a range of plant capacities (from 58 to 230kt/day) combined with a range of mining capacities (from 83 to 166Mt/a) were evaluated in detail, defining for each option a mine plan, Capex and Opex, and cut-off grade strategy for flotation and leaching processes and the associated Net Present Value (NPV) that was used as the selection criteria. The Los Bronces mineral resources potential provides good growth opportunities for the mine beyond LBDP implementation, offering an exciting invitation to continue studying new initiatives that maximise the value of this deposit.

Jan 1, 2008

By E. Bakhtavar, R. Mikaeil, D. Khademi

"Fuzzy-weighted integer goal programming has been developed and used to select the most suitable site to construct a central processing plant for several adjacent small-scale dimension stone quarries, based on the most effective criteria. In the first step of mathematical modelling, the most important goals and decision variables were defined. Accordingly, an objective function was used in the model for minimizing the sum of undesired fuzzy-weighted deviations. Fuzzy weights were determined by a matrix of pairwise comparisons of various expert judgments in this field and the fuzzy geometric mean. The goal and systemic constraints were also modelled. The most suitable site for the construction of the plant was selected after solving the mathematical model in the ExcelR Solver add-in. The selected site had various advantages over the other sites, such as the shortest average distance to the quarries, the shortest distance to power access and workforce, and the lowest land price. IntroductionSelection of the most suitable site of a plant is one of the most important considerations when constructing an industrial project. A suitable site has a significant effect on a company's competitiveness in the market. Selecting a desirable location for constructing plants such as mineral processing facilities is an essential part of the economic planning that will enable a company to meet the needs of related upstream and downstream operations. These units are considered to be best built near the relevant mining sites because of technical difficulties, the cost of transporting minerals, and the traffic hazard caused by the movement of trucks transporting materials. Two main types of research using multiattribute decision-making models have been reported for selection of a processing plant site (Safari et al. 2010, 2012). In that research, the analytic hierarchy process (AHP) and fuzzy technique for order preference by similarity to ideal solution (TOPSIS) approach were applied to select the suitable locations for the mineral processing plants for phases 1 and 2 of Sangan iron ore mine."

Jan 1, 2017

By J. W. Neale

Mintek was a leading participant in the BioMinE project between 2004 and 2008. This project, which was funded in part by the European Commission, was aimed at the development of biotechnology for the minerals industry in Europe. Mintek?s research programme focused mainly on the development of integrated bioleach-based processes for the recovery of base metals from complex, low-grade sulphide concentrates. Specific European mineral resources were targeted and used in integrated piloting campaigns involving bioleaching, solution purification, and metals recovery. This paper describes the use of thermophilic bioleaching for the recovery of nickel and copper from a low-grade nickel-copper concentrate produced at the Aguablanca Mine in southern Spain. Currently, the Aguablanca Mine produces a bulk nickel-copper concentrate for sale to a smelter, and the proposition is to increase the profitability of the operation by the on-site production of metal or metal intermediate. Initially, bench-scale bioleach tests were conducted to determine the bioleach operating conditions. These tests included an evaluation of mesophilic, moderately thermophilic and thermophilic microorganisms. In order to achieve sufficiently high levels of both copper and nickel extraction, a thermophilic process was selected?this was necessary for leaching of the refractory chalcopyrite that occurs in this concentrate. Additional bench-scale test work was carried out to derive a conceptual process flowsheet for the solution purification and metals recovery circuit. The results of the bench-scale tests were used to design, construct and commission an integrated pilot plant, which was subsequently operated at Mintek for over seven months. During this time, the solution purification and metals recovery processes were optimized, and all recycle loops were closed. The final process flowsheet included the following unit operations: concentrate regrinding, thermophilic bioleaching at 70°C, primary iron removal using limestone, copper solvent extraction and electrowinning, secondary iron removal, nickel hydroxide precipitation using magnesia, and final solution purification using lime. Where applicable, process solutions were recycled to preserve water. The process design data derived from this pilot-plant campaign formed the basis for a conceptual engineering study for the developed process. In the study, mass and energy balances were derived, and a process flowsheet was developed and used as the basis for estimating the capital and operating costs of the process. This enabled a preliminary economic analysis of the process to be undertaken. The findings of this study are discussed.

Jan 1, 2009