Search Documents

By F. R. Deist, R. P. Plewman

Discussion: A. Hazell (Associate Member) and T. J. Kotze (Graduate Member): The authors must be congratulated on the development of a versatile computer programme for determining the stresses and displacements resulting from mining operations. As a design tool it will no doubt take its rightful place together with the analogue computer. Union Corporation made use of this digital computer programme whilst still in its development stage to determine the stress distributions which were causing the unexpected failure of the Marievale sub-incline shaft. Two features arising from this investigation may be of interest to members, namely: A. The solution to the problem of stabilizing a rectangular inclined shaft, which turned out to be contrary to accepted mining practice, and B. A comparison between the results obtained with the pure digital system and the analogue computer. A. The shaft is nine ft high and 20 ft wide, dipping at 9° to the horizontal and crossing the bedding planes. Fig. 1 is a plan and Fig. 2 is a section of the sub-incline shaft pillar area showing the relative positions of the shaft and reef as well as their respective dips. The deepest point in the shaft is 3 300 ft below surface and the requirement of a stress free ground surface may not be satisfied. It also means that the original gravitational stresses are low. A 900 ft wide pillar was left to protect the bottom section of the shaft, the top section being understoped years ago. Extraction of the pillar was started at the beginning of last year, mining operations being carried out in the accepted manner, starting beneath the shaft and mining outwards. The approach did, however, turn out to be the wrong one, because failure of the shaft was noticed soon afterwards. Even small movements were serious in this case due to the low clearance between the skips and the shaft supports. During October, 1968, failure between benchmarks 8 and 10 (see Fig. 1) became so excessive that hoisting speeds had to be reduced. Failure continued to occur and, by the end of March, 1969, failure had propagated up the shaft as far as benchmark 7, and down as far as benchmark 12. As this shaft had a tight hoisting schedule it was imperative that a quick solution be found to arrest the failure.

By J. W. D. Groenewald, L. Auret, B. S. Lindner, E. C. Nienaber

Mineral processing plants have complicated control strategies, with different control layers, multiple interacting loops, and feedforward disturbance rejection. The complicated control strategies mean that oscillations can arise and propagate to multiple loops and degrade the control performance. Oscillation detection techniques, such as the spectral envelope method, can be applied to detect oscillations within an observation window. However, the start- and end-points of the oscillations within the observation window cannot be identified with current oscillation detection techniques. The start- and end-points would be useful to label the oscillatory intervals, and then to use these labels to identify process conditions associated with the oscillation. In this paper, a pattern recognition technique, Density-Based Spatial Clustering of Applications with Noise (DBSCAN), was used to label oscillation intervals. An oscillation diagnosis workflow combining spectral envelope and DBSCAN was demonstrated on an industrial case study of oscillations in a flotation circuit concentrate sump. The workflow successfully detected the oscillation, labelled the oscillatory intervals, and enabled accurate root cause analysis. The impact of time series features, namely the signal power ratio () and the oscillation frequency, on the performance and optimal parameter selection of DBSCAN was also investigated. Low oscillation frequencies and low s negatively affected the performance of DBSCAN. Additionally, the results indicated that higher oscillation frequency was related to higher optimal values for the lag parameter. Keywords: Oscillation diagnosis, process monitoring, data mining, clustering, flotation control

Jan 1, 2020

By Mr P. W. J. van Rensburg

SOUTH AFRICAN NATIONAL COMMITTEE ON TUNNELLING In 1970, the South African Institution of Civil Engineers, the South African Institute of Mining and Metallurgy, the South African Institute of Mechanical Engineers, and the Geological Society of South Africa held an international conference on tunnelling, known as Tuncon 1970. SUID-AFRIKAANSE NASIONALE TONNELBOUKOMITEE In 1970 het die Suid-Afrikaanse Instituut van Siviele Ingenieurs, die Suid-Afrikaanse Instituut vir Mynbou en Metallurgie, die Suid-Afrikaanse Instituut van Meganiese Ingenieurs en Die Geologiese Vereniging van Suid-Afrika 'n internasionale konferensie in verband met tonnelbou gehou, wat bekend gestaan het as Tonkon 1970.

Jan 5, 1974

By J. E. Furze

World-wide hikes in the oil price and the prospect of future scar cities of liquid and gaseous fuels have given enhanced status to the South African coal industry. It is thus understandable that the colloquium held at Wit bank on 3rd and 4th October, 1979, and organized jointly by the South African Institute of Mining and Metallurgy and the South African Coal Processing Society should have attracted more than 400 delegates.

Jan 1, 1979

By M. E. E. Douglas, A. K. Haines, D. I. Nicol, C. M. Olëm, W. M. Craig, G. D. Louw

A description is given of the design of the continuous ion-exchange demonstration plant at Blyvooruitzicht Gold Mine, including details of the process design, the column construction, and the control system. The operating and process results gathered over a period of seventeen months are summarized, and development work and modifications to the process are discussed. It is concluded that the system comprising continuous loading and continuous elution is technically feasible and can be scaled up with confidence.

Jan 1, 1978

By M. J. Nicol

This paper ,examines the kinetics of the extraction of uranium from acid sulphate solutions by strongbase anionexchange resins. Parameters such as the concentration of uranium in solution. the agitation of the resin beads in solution. the size of the resin beads. and the degree of cross-linking within the resin matrix were varied. and the effec ts on the kinetics are reported. The applicability, of various empirical kinetic models to the description of the data is assessed, and an attempt is made at the modelling of the rate data in terms of established theories about the diffusion of ions through films of stagnant liquid and through spherical beads of resin.

Jan 1, 1980

By R. I. Klintworth

The multi-reef area of Cooke 3 Shaft provides a unique mining challenge on account of the very thin middlings between the pay bands and the marginal values of the reef. It is uneconomic or impractical, because of the excessive heights, to mine the middlings using conventional stoping methods. The development of suitable mining methods is discussed with particular emphasis on the control of water inflow and the policy of not jeopardizing or sterilizing other reef horizons by the mining method implemented. No definite solution is currently available, but with the aid of instrumentation, computer analyses and mechanized mining equipment, the mine continues to attempt to maximize extraction and profits.

Jan 1, 1988

By Y. Suzuki, H. Yoshida, K. Sakaguchi, K. Matsuki, M. Minami

To estimate three dimensional in-situ stress at great depth, Downward Compact Conical-ended Borehole Overcoring (DCCBO) technique, which is one of stress relief methods, was developed. DCCBO technique can be applied to a water-filled vertical/sub-vertical borehole. In in-situ tests, the bonding device and the cleaning system were verified to work well in a water-filled borehole with cuttings on the bottom. Um dreidimensionale in-situ Beanspruchungen in großen Tiefen abzuschätzen, wurde das Downward Compact Conical-ended Borhole Overcoring (DCCBO) Verfahren entwickelt, wobei es sich um ein diese Beanspruchungen entlastendes Verfahren handelt. Die DCCBO Technik kann auf wassergefüllte vertikale und subvertikale Bohrlöcher angewandt werden. Bei den in-situ Tests wurde die Einsatzfähigkeit der Verbindungsvorrichtung und des Reinigungssystems für wassergefüllte Bohrlöcher mit Einschnitten am Boden bestätigt. La technique de Downward Compact Conical-ended Borehole Overcoring (DCCBO) ou ‘Surcarottage par sondage à extrémité conique compact dirigé vers le bas’, qui est une méthode de détente des tensions, a été développée pour calculer les tensions in-situ à trois dimensions à grande profondeur. Cette technique peut s’appliquer à des sondages verticaux/sub-verticaux remplis d’eau. Au cours des essais in-situ il a pu être vérifié que le dispositif de liaison et le système de nettoyage fonctionnaient bien dans un trou de forage rempli d’eau avec saignées au fond.

Jan 1, 2003

By D. G. Krige

Recent publications have demonstrated the important role that can be played by a priori information of the grade levels, variability, and spatial patterns in adjacent or nearby areas in improving the quality of grade estimates for virgin or sparsely drilled areas. A research project was therefore conducted involving the collection and analysis of extensive sampling and borehole data from 7 reefs on some 30 Witwatersrand mines. This paper shows that the 'equivalent' log variance for the two-parameter lognormal model provides a good basis for the study and comparison of the levels and behaviour of relative variances. The trends of these against the corresponding log areas were found to form distinctive patterns, which are useful for these purposes. The patterns for the Basal, Vaal, Carbon Leader, and Main Reef Series form a reasonably close group, whereas those for the V.C.R.(particularly where the facies are mixed), B Reef, and Kimberley-Elsburg Reefs (particularly for narrow channel widths) do not always conform. The patterns shown by underground chip samples are also compared with those obtained from borehole cores. It is shown how this information can be used to improve the borehole valuation of new mines and of virgin areas in existing mines.

Jan 1, 1993

COUNCIL The following served on Council during the year under review: Office bearers: Prof D. D. Howat (President), Dr J. P. Hugo and P. W. J. van Rensburg (Vice-Presidents), V. C. Robinson (Immediate Past President) and D. G. Maxwell (Honorary Treasurer). Ordinary Members of Council: H. P. Carlisle, R. C. Espley-Jones, G. H. Grange, Dr D. I. Legge, W. W. Malan, Prof R. P. Plewman, Dr R. E. Robinson, Dr M. D. G. Salamon, L. W. P. van den Bosch and P. A. von Wielligh. Branch Chairmen: A. Bain (Witbank-Middelburg Branch), J. M. Meyer (O.F.S. Branch). Past Presidents serving on Council: R. J. Adamson, M. Barcza, H. Britten, H. E. Cross, J. K. E. Douglas, R. C. J. Goode, P. Lambooy, Prof J. de V. Lambrechts, Dr J. T. McIntyre, J. F. Reid and H. Simon (until March 1972). Ten Council meetings were held during the year with an average attendance of nineteen, and the standing committees held 27 meetings. FINANCE The annual accounts which are attached to this report show an excess of income over expenditure of R21 519. It is very gratifying to be able to report that Council's efforts to stop the depletion of our accumulated funds are meeting with success. The most important contributors to our surplus this year are symposia and colloquia, sales of publications, Company Affiliate subscriptions and the profit on the journal. While we do not expect continued profits from all these sources in the future we do feel that we are now in the process of accumulating a substantial financial foundation. This will give the Council the necessary confidence to initiate the new developments in the activities of the Institute which are now under consideration. The decision to create a new grade of membership, Company Affiliate, is dealt with elsewhere in this report. There has been a generous initial response from companies and this is the cornerstone of our improved financial expectations. The MacArthur Forrest Memorial Fund shows an excess of income over expenditure of R91 and the total fund was, therefore, increased by this amount to R4 502. The balance sheet shows that the market value of quoted shares and debentures increased during the year from R9 160 to RH 331, which is R2 134 in excess of the book value. Accumulated funds now amount to RH 529 compared with R23 010 a year ago. MEMBERSHIP Sixteen Fellows, twenty Members, six Graduates, nine Associates, twelve Students and twenty-four Company Affiliates were elected during the year. One Member and two Associates were reinstated. Twelve members were admitted to retired membership. Transfers: Member to Fellow, three. Graduate to Member, seven Associate to Fellow, one. Student to Member, one. Student to Graduate, four. Student to Fellow, one. Your Council records with deep regret the death during the year of the following: Dr A. J. Orenstein (Honorary Life Fellow), R. A. Cooper, R. J. Spargo, H. Simon and F. Meyer (Life Fellows), S. D. Loxton, W. P. Arnold, G. C. Needham, W. G. Pyne-Mercier, J. Innes and O. T. Wright (Fellows), E. P. Mennell and O. B. Prentis (Members), J. Brits (Associate). After careful consideration of all the implications it was decided during the year to create a new grade of membership to be known as Company Affiliate, in order that there might be a formal and permanent channel for companies to contribute to the important work of the Institute. As recorded above, 24 companies had joined by the end of the year and many further applications have been received since. We extend a hearty welcome to all our new members. A comparative statement of membership as at 30th June, 1972, and the end of the previous year is shown in the following tabulation:-

By G. Song, X. Liu

The global coal industry has changed significantly in recent years. In this paper we analyse the coal production and consumption, imports and exports, and coal prices in China and other major coal-producing countries during the past four decades. The analysis shows that global coal production and consumption have declined over the last three years, in striking contrast to the continuous growth for most of the past 35 years. Australia, Indonesia, and Russia have become the world’s major coal providers, while China, India, and the USA, and Germany are the major coal consumers. The world’s, and China‘s, coal industry can be classified into four stages of development: the stable growth phase, stable phase, rapid growth phase, and high-quality phase. Coal prices rose in the world’s four major coal markets in 2016 after four consecutive years of falling prices. The elimination of overcapacity and production-optimizing operations in China could assist in achieving a demand and supply balance.

Aug 8, 2024

By C. B. van den Berg

n this study, silver and palladium nanoparticulate inks with different metal-binder ratios were screen-printed onto a paper substrate. The printed layers comprised the metal nanoparticles and an ethylcellulose binder. The layers are not typical metal composites due to the low concentration of binder and high porosity. The electrical sheet resistivity of each particle concentration was measured, and the data fitted using the scaling law of percolation theory and the general effective media (GEM) equation. The percolation parameters, i.e. the percolation threshold and the critical exponent, for each system were determined from the fits and compared. The percolation threshold for the palladium layer (39.8 wt%) was lower than that found for the silver layer (44.9 wt%). The critical exponents determined for the palladium and silver layers were both lower than the universal value for three-dimensional percolation systems. Microscopy observations indicate that the difference in the percolation threshold for the two layers can be attributed to variations in their microstructure.

Jan 1, 2014

By L. S. Bicalho, W. J. Rodrigues, P. M. A. Rollo, P. R. G. Brandão, W. C. da Silva

Quadrilátero Ferrífero is an important mineral province located in Minas Gerais state, responsible for a substantial amount of iron production in Brazil. Among the concentration methods for iron ore practised by the mining companies in this region, the most important is the reverse cationic flotation. Dolomite iron formations, with the presence of hematite, quartz and dolomite, occur in several areas of mining and, with the deepening of the deposits, this type of ore, with low iron content and more complex mineralogy occurs frequently. Carbonaceous minerals, mainly dolomite, present a technological challenge for the concentration of iron ore by flotation. In the present study, the concentration of iron ore with 6% of dolomite content was evaluated. Bench flotation trials indicated that conventional iron ore flotation is not selective to float dolomite, thus compromising the iron content in the final concentrate. Alternative flotation routes were evaluated, and a selective condition was reached to float both quartz and dolomite using the combination of the cationic collector Flotigam 16424 with an anionic collector Flotinor 16551. It was demonstrated that the flotation of dolomite was improved with the combined use of both collectors in the cleaner stage, and by a previous quartz flotation in the rougher stage. Zeta potential analysis indicated specific adsorption as the adsorption mechanism between Flotinor 16551 and dolomite, confirming the high selectivity observed in the bench flotation tests. Keywords: Flotation, iron ore, dolomite

Jan 1, 2020

By J. Botha

There are many underground mining software tools available to plan and schedule the development of underground mines. A shortfall of these tools is the optimization of the underground equipment and strategy in order to maximize the development rate. This paper will illustrate how the SimMine® software was used to maximize underground development at Petra Diamonds' Cullinan Diamond Mine. It will also determine the effect of various development strategies and equipment capacities on the underground development rate and pinpoint potential bottlenecks in the mine development cycle.

Jan 1, 2010

By D. N. Esfahani, K. Khazen, M. Mohammadi

Electrowinning is one of the nickel recovery processes from solutions obtained from the leaching of nickel sources. Every year significant amounts of nickel products are used in various industrial processes and daily life, such as catalysts or batteries, which are a valuable source of nickel for recovery. Nickel purity is also very important in the electrowinning process, because the amount of impurities in nickel such as sulphur, if greater than 100 ppm, make it unsuitable for use in catalysts and plating. Because sulfur is intrinsic to the sulphate electrowinning system, we needed to investigate parameters that can affect the quality and purity of nickel. In this regard, experiments were performed in static and circulating electrowinning processes. A monitoring and circulation system was designed and built to measure voltage, current and temperature as well as to circulate the solution in the system at a specified rate. It was then observed that nickel ion concentration, pH, using the circulation system and additives, were factors affecting the purity and quality of nickel, and in the best case the amount of sulphur in nickel was below 100 ppm. Keywords: Nickel, electrowinning, sulphur impurity

Jan 1, 2020

By J .. F. Brownrigg

In the mining method used at O'Okiep Copper Company (OCC), vertical crater retreat, the prime requirement for the fill is that it should be sufficiently strong to be free-standing to a height of 150 m. Other requirements are minimal decant and drainage water, and high pulp density to allow large tonnages to be placed quickly and alleviate transport problems. The excessively high cost of cement precluded the use of a cement-based fill, and after three years of extensive investigations a backfill based on the smelter slag was produced. Currently a fill with a uniaxial compressive strength of greater than 1 000 kPa after one month is being produced. This is in excess of the design specification of 850 kPa after 2 - 3 months. The research and development which went into the slagfill is briefly covered; the production of the fill from the various raw materials is described; and the design and control systems of the backfill plant, the reticulation system and its monitoring are examined. Finally, the implications of this high- quality fill for the mining programme are assessed.

Jan 1, 1988

By F. Yang, S. S. Long

Mixed fatty acids, such as oxidised paraffin soap, are frequently used as a substitute for oleic acid in flotation of scheelite in China. Not only because it is cheaper than oleic acid, but also because it is superior in flotation performance to oleic acid. This superiority is generally attributed to the mixed fatty acids' synergistic effect. In this paper, the synergistic effect of oxidised paraffin soap was investigated. We found it mainly consists of a series of saturated fatty acid salts, with six to nineteen carbon atoms. All the contained fatty acids were classified into four groups based on their chain length to make the research work practical. Also, the groups were labelled as 1, 2, 3, and 4 in order. The research was simplified into studying the synergistic effect of four equivalent collectors, instead of fourteen fatty acids. It is justified by the fact that neighbouring fatty acids are expected to have a similar flotation performance. The synergistic effect of the four groups of fatty acids was studied by single-mineral flotation with single groups, binary mixtures, ternary mixtures, and the full component, as collector respectively. The flotation performance index and synergy value were introduced to evaluate flotation performance and synergistic effect of groups, respectively. The results show that the mixture 1+2+3 has the strongest synergy of all followed by the mixtures 1+3 and 2+3. The mixture 3+4 and 1+2, on the other hand, have negative synergy. The synergistic effect of mixtures of groups indicate that being consecutive in length and a broad range of lengths are vital for fatty acids to enhance synergy. Group 3 is fundamental for the collecting action of 733 oxidised paraffin soap in the flotation of scheelite. The fatty acid soap in group 4 is not suitable for flotation due to its low solubility. Keywords: Mixed collectors, synergistic effect, scheelite

Jan 1, 2020

By R. o. Cretier, L. A. Cisternas, A. López-Valdivieso, F. Valdes, E. Gálvez, G. Gahona

The size of the particle plays an important role in the flotation of minerals. Comminution allows the release of valuable species and their subsequent recovery. Then, the degree of concentration and recovery will depend on the size of the particle. In this work, we investigated the flotation of coarse particles (-850 +150 μm) of copper ores when using the fluidized-bed separator (HydroFloat® cell) and compared it with the process of conventional flotation with medium size particle (-150 μm) (Metso cell) using seawater. The collector concentration was the main variable studied in terms of copper recovery. The results show that the flotation of coarse particles is feasible using seawater without frother

Jan 1, 2020

By M. Saghaeian, R. Hejazi, L. Hosseini, M. V. Sheikhzadeh

HPGR equipment has been well proven to be energy-efficient in the first stage of grinding in iron ore beneficiation plants. Numerous advantages of utilising HPGR grinding prior to ball mill grinding, such as reducing the power consumption in a ball mill through generation of micro-cracks, has been thoroughly studied. Less attention has been paid to efficiency of the HPGR circuit rather than the downstream ball mill circuit. In this study the HPGR circuit has been optimised through feed size reduction by crushing, and feed iron content upgrading by dry cobbing. This optimisation leads to better operation of the HPGR, and a smaller product size which is expected to result in a lower wear rate of ball mill liners and balls. It is also expected that the top size of the ball mill balls be reduced. Additionally, by reducing the feed size of HPGR from 30 mm to 15 mm, it is possible to achieve similar K80 of HPGR product in lowered pressure, i.e. 2.5 N.mm-2 instead of 3.5 N.mm-2 which translates to ease of operation. Similarly in a given roll pressure, smaller feed sizes result in higher specific throughput of ~10% which means higher production capacities. The results also reveal that this optimisation increases the concentrate weight recovery by about 10%. It also results in slight increases in the Fe grade of the product iron concentrate. Keywords: HPGR, HPGR circuit optimisation, crushing prior to HPGR, dry cobbing prior to HPGR, ease of operation, concentrate grade optimisation, weight recovery optimisation

Jan 1, 2020

By J. -M. Milazzo, T. Wallmach, S. B. Blancher, A. Amalric

In a FeNi electric arc furnace, the physical properties of the slag (chemistry, viscosity, liquid/solid/gas ratio) are of crucial importance in controlling the efficiency of the process. In this paper, we studied the slag crystallised on the walls of a semi-industrial furnace (freeze-lining), the slag rising through the burden during foaming phenomena, and the casted slag. The freeze-lining is the layer of oxides that crystallises on the refractory wall of a furnace, protecting it from chemical and mechanical aggression. It records changes in furnace conditions (slag chemistry, temperature, oxygen fugacity), which makes it possible to observe the impact of these elements. In the high reduction test, the freezing lining is composed of magnesian olivine. Switching to a low reduction process increases the Fe content of the olivine and causes orthopyroxene to appear, making the freeze-lining mechanically and thermally weak. Thermal incidents in the furnace cause significant slag foaming. This foaming is produced by a massive crystallisation of the olivine (due to the drop in temperature), and inducing an exponential increase in viscosity, preventing the free circulation of gases. These foaming episodes are also recorded in the freeze lining and form layers rich in gas bubbles, and therefore mechanically fragile. The slag casted and cooled in a ladle allows the first steps of slag crystallisation to be studied. Olivine is the liquidus phase, with a magnesium-rich core and an iron-enriched rim, contemporaneous with the orthopyroxene phase. The habitus of these phases is very similar to that found in komatiites for the same minerals. FeNi slag is therefore an industrial analogue that is easy to study and compare to komatiites. Keywords: Pyrometallurgy, ferronickel, slag, freeze-lining, characterisation, olivine, mineralogy

Jan 1, 2020