Search Documents

By H. A. D. Kirsten

The effects of the mining of deep-level tabular reefs are usually evaluated by use of continuum, elastic mining simulation analyses. This paper gives the results obtained from a series of analyses in which stopes of limited span are considered to be excavated in a non-linearly non-elastic, jointed and fractured rockmass. In particular, the theoretical influence of soft backfill in these conditions is evaluated. It is shown that the stress distribution and behaviour of the rockmass, alternately taken as an intact-elastic and as a fractured non-elastic medium, are completely different. The relevance of the energy-release rate commonly calculated in mining-simulation analyses, and the efficacy of its correlation with seismicity and the associated rockbursts, are reviewed. In deep-level mining operations, it is not practically feasible to obviate releases of seismic energy. The fact of their occurrence should therefore be accepted and, rather than considering the reduction of energy release as the primary objective, efforts should be concentrated on minimizing the effects of such release. Analytical results are given to demonstrate that this approach is not only correct, but also the only feasible solution to the rockburst-seismicity problem in deep mines.

Jan 1, 1989

By Q. G. Reynolds

The dual-electrode DC arc furnace, an alternative design using an anode and cathode electrode instead of a hearth anode, was studied at small scale using computational modelling methods. Particular attention was paid to the effect of two key design variables, the arc length and the electrode separation, on the furnace behaviour. It was found that reducing the arc length to brush arc conditions was a valid means of overcoming several of the limitations of the dual-electrode design, namely high voltages and arc deflection.

Jan 1, 2012

By O. Y. Ntrama

Lebowa Platinum Mines has been in operation since the late 1960s and is a relatively small producer compared to Anglo Platinum?s other operations. The mine has never had substantial capital investment to expand its production scale even though its resource base is estimated in excess of 100 years at current mining rates. It is forecast that the mine will become unprofitable after 2008 due to the workings of the ageing infrastructure, the Merensky Reef operations being further from the shafts, decrease in productivity and increase in operating costs. In order to reverse the forecast decline in operational inefficiencies and profitability the replacement of the Merensky Reef operations at Vertical and UM2 shafts with the development of a 120 Ktpm Brakfontein Merensky Reef Mines is in progress. This paper covers the operational readiness framework developed from the control budget estimate and outlines an integrated business process adopted to ensure that the requirements of the investment proposal are met. The operational readiness framework, which addresses the transition process, will ensure that at operational start-up, all appropriate operating systems, procedures, information and legal requirements are in place, whereas the business integration process will aim to develop and sustain an organization with the appropriate infrastructure and workforce equipped with the necessary skills to meet Brakfontein?s requirement, and where possible embark on an optimized accelerated production initiative to ensure that the objectives of the investment proposal are sustained. Keywords: operational readiness, business integration, optimized accelerated production initiative, organizational development.

Jan 1, 2006

By A. Bain

The use of plastics in the coal mining industry is making slow progress whereas these materials could make a greater contribution to safety, to a reduction of working costs and to the higher productivity of mine workers. Possibly the reluctance to experiment with the new material of our age is due to the low profit margin of coal mining. This note has been prepared to present a brief survey of what has been done in the last few years and to mention some of the investigations the author has made and is making in an attempt to develop more use of plastics in the industry. Some of the plastics used on the mines have taken their place in the industry in the same manner that they are used in everyday life while others have been introduced because there has been a need for them. New uses and applications are being developed and these are the ones that are most interesting. The plastic that is specially developed to give the maximum benefit and not the one that is a modification of some other everyday product is the next development in the field. Many manufacturers are keen to promote such investigation but are not aware of the problems the mines wish to solve and therefore it is only through management itself that this development can be carried out. This note deals with plastic material under three headings: (a) Plastic as the superior material, and briefly describes how plastic has replaced a few major items which are better when made from plastic. (b) Plastics of necessity, being a short summary of how plastics had to be introduced because of laws and conditions making it a necessity. (c) Development of new ideas, being briefly some of the ideas being developed overseas and some of the ideas being tried by the author. Plastic items in common use such as in housing, electric cables, laboratory equipment, awnings, nylon bearings, locomotive brake linings, etc. being well known are not discussed. PLASTIC AS THE SUPERIOR MATERIAL Plastic belting underground Following a fire in a belt road in England resulting in the deaths of many workers, and subsequently a fire accompanied by fatalities in a belt road in a mine in this country, a law was introduced which states that only flameproof belting is to be used underground. This ruling forced the mines to use P.V.A. belting as no other was available. This belting has non-inflammable characteristics that are superior to rubber. Due to the high tension on long-distance belts used today the need for stronger belting material called for something better than cotton and the answer to this was nylon. Nylon also has the ability to withstand dry-rot which reduces the life of a belt very quickly.

By L. Thomas, D. Muteba, L. I. Nsenga, B. Mbao, G. Longo Banza

Owing to the high ore grades in the African Copperbelt and variable acid consumption, agitated leaching is common practice and is used more widely in Africa than in other regions. Two common challenges for agitated leach–solvent extraction circuits are higher presence of colloidal silica in the pregnant leach solution and elevated levels of total suspended solids. Both can negatively affect the physical and metallurgical performance of the solvent-extraction circuit, and lead to higher processing costs or reduced copper production. Operating in organic continuity is preferred to address such challenges, but is not always possible: additional treatment options may be advantageous. For this reason, Solvay recently introduced ACORGA® CR60LT, a new chemical additive to address these concerns. Continuous addition to the pregnant leach solution improves physical performance without negatively affecting Cu transfer or cathode quality. Results and benefits from commercial utilization of ACORGA® CR60LT at different operations in the Copperbelt are reviewed

Jan 1, 2023

By P. J. Petit

Financial evaluation is necessary to investigate the viability of implementing and/or utilising new technology in mining projects. It establishes a techno-economic base for decision-making and justifies capital expenditure. This paper aims to present a monetary appraisal of the electric rock drilling system in a typical feasibility project, whose purpose is to increase the production rate. The in situ environment is a platinum orebody, and the stoping operations occur in UG2 reef. The results are a function of production requirements, technical parameters and financial outlay of the drills. The costs involved in implementing and operating electric rock drills are assessed to the current method of drilling, namely the compressed air operation. A comparison of the electric and pneumatic rock drills in terms of financial outlays for drilling and service requirements, peripheral equipping and training is discussed. Other factors that affect the business case are technical advantages, safety and risk management and the environmental objective of the company.

Jan 1, 2006

By H. S. Sichel, Kleingeld

A frequency distribution model plays a fundamental role in ore evaluation, especially for the feasibility study of new deep gold mines. The geological complexity of the reefs being mined at present in the Witwatersrand basin poses some difficulties regarding the modeling of the underlying ore-value distribution. This geological complexity has given rise to a need for more applicable distributional models. This paper places the geology of the Witwatersrand basin in perspective and draws some important conclusions from the genesis of the deposition. In addition to the three-parameter lognormal model, two more-general distributional models are proposed. These are the compound lognormal (CLD) and log-generalized inverse Gaussian (LN-GIG) distributions. A detailed, although preliminary, comparative study of these two more-general models with the three-parameter lognormal model is described, and the efficiencies of the estimates and modeling are analysed. It is found that the broad assumption that gold grades follow a three-parameter lognormal law is not always the case, and the need to test for departures from log normality should be emphasized so as to ensure the use of appropriate models.

Jan 1, 1992

By J. van der Walt, A. Whillier

Reference is made to the approach to mine cooling in which the service water is used as one of the means of distributing refrigeration, and attention is drawn to various engineering disciplines or functions necessary for effective distribution and reticulation of cold water from refrigeration plant. The demand for service water is intermittent, the peak flow-rates being typically two to three times the average flowrate. The refrigeration plant, on the other hand, must preferably be operated steadily throughout the day and night, with the result that a large storage dam for cold water must be incorporated into each system in order to even out the surge in demand for water. These dams should be operated as constant-temperature, variable-volume reservoirs. The conventional cascade system involving dams on each level is not the best for sending water down mines, and schemes are described that avoid the need for such dams. Reference is made to various tests that were carried out, and to several large systems that were installed. Management and organizational problems that could arise as a result of new technological developments in mine cooling are referred to, and cost figures are quoted to indicate the large potential savings, In addition to the improved environmental conditions, that can be achieved through the use of integrated water systems.

Jan 1, 1979

By A. H. Swart, M. F. Handley

Unplanned stope panel collapses occur on most near-surface and shallow mines in South Africa. Although these incidents often occur during blasting, they pose a major threat to the safety of underground workers and the economic extraction of orebodies. Most stope panel collapses occur due to excessive panel lengths that are not designed according to a systematic design procedure or methodology. Instead, panel lengths are often dictated by the equipment in use and by previous experience under similar conditions. Hence, a rock engineering design methodology for the design of stable stope panels between pillars is of vital importance for optimum safety and production in shallow mining operations. Using the proposed design methodology described in this paper, rock mechanics practitioners and mine planners should be able to identify and quantify the critical factors influencing the stability of stope panels. The critical factors should then be used as input to the design of stable stope panels that will provide the necessary safe environment for underground personnel working in stopes. The proposed design methodology is an iterative process, which includes aspects such as rock mass characterization, estimation of rock mass properties, identification of potential failure modes, consideration of appropriate stability analyses and other elements of the rock engineering design process. This process continues after implementation. During monitoring, new data should be included in the database and the design process repeated on a regular basis. Design approaches included in the proposed design methodology include empirical methods such as different rock mass classification methods, analytical methods such as elastic and Voussoir beam analyses, kinematic analyses, probabilistic analyses, and numerical analyses. Keywords: stability, stope panels, design methodology, hard rock mines, shallow mining operations

Jan 1, 2004

By N. B. Devi

The extraction of Cu(II) from HCl media using Cyanex 923 in kerosene was investigated. The effect of shaking time, aqueous phase acid concentration, extractant concentration, chloride ion concentration, various metal ions (Mn2+, Mg2+, Fe2+, and Ni2+), and temperature on the extraction were studied. Using 0.1 M Cyanex 923 the extraction of Cu(II) was 6.7 per cent from 3 M HCl, which increased up to 78.5 per cent with 6.5 M HCl and then decreased due to acid extraction by the extractant. The maximum extraction (97.5 per cent) was obtained with 1 M Cyanex 923 from 5 M HCl solution. A mathematical model has been developed to describe solvent extraction equllibria over wide ranges of concentration of extractant, acid, and chloride ions. The composition of the extracted species has been predicted on the basis of slope analysis results and extraction equilibrium modelling. The negative values of enthalpy change and entropy change confirm the exothermic formation of the extracted complex.

Jan 1, 2012

By R. Tabanrad

This article examines the stability analysis of intake tunnels of Karun III dam & power plant. The tunnels have been excavated with a 3-dimensional and fairly complicated geometry in Pabdeh weak formation rocks at Zagros region. Due to the particular excavation geometry and inapplicability of plane-strain status, the stability of these excavations has been analyzed using both the 3D elastic software Examine 3D and the 2D non-elastic software UDEC simultaneously. The geomechanical parameters have been estimated by back analyzing the measured displacements from instruments, which were installed in the tunnels, and the parameters have been used in non-elastic numerical model. The results of the analysis show that the strains occurred in surrounding rock mass are less than the allowable failure strain and that the tunnels are stable. In addition, considering the results of non-elastic 2D analysis, the areas with unstable potentiality were identified and after the instability occurred at the areas predicted by the model , it was stopped up to the allowable strain limit through installing additional support . Bei diesem Artikel handelt es sich um eine Analyse der Festigkeit der Eingangstunnel des Damms und Elektrizitätswerks “Karoon III”.Die Tunnel haben drei Dimensionen und eine sehr schwierige Form und sind in brüchigen Felsen in “Pabedeh ,in Zagrossgebirge”eingebohrt.Aufgrund besonderer Form der Bohrung wurde ihre Festigkeit durch elastische dreidimensionale Soft-ware analysiert,die gleichzeitig die drei-und zweidimensionale unelastische Soft-ware UDEC benutzt hat.Die geometrische Parameter sind mit Ausnützung der Analyse berechneter eingesetzter Versorgungen,die in Tunnel aufgebaut sind,bewertet.Und diese Parameter sind in Zahlen-Analyse benutzt.Die Ergebnisse dieser Analyse zeigen,dass die Drücke an Felsen weniger als problematischer Grad der Drücke sind und die Tunnel fest sind.Ausserdem wurde mit einem Einblick auf die Ergebnisse der unelastischen zweidimensionale Analyse die eventuellen unfesten Teile bestimmt.Nach entstandener Unfestigkeit an diesen Teilen wurde die problematischeDrücke für Aufbau mehrere Anlagen gestoppt. Cet article examine l'analyse de la stabilité de tunnels de la prise de Karoun barrage III et centrale électrique. Les tunnels ont été excavés avec une 3 dimensionnel et compliqué géométrie dans Pabedeh que la formation faible balance à région Zagros équitablement. Dû à la géométrie de l'excavation particulière et inapplicabilite de statut de tension plane, la stabilité de ces excavations a été analysée en utilisant les deux le 3D logiciel élastique Examen 3D et le 2D logiciel non - élastique UDEC simultanément. Les paramètres du geomechanical ont été estimés en analysant le déplacement mesuré d'instruments qui ont été installés dans les tunnels et les paramètres en arrière a été utilisé dans les modèles numériques non - élastique. Les résultats de l'analyse montrent que les tensions se sont produites dans masse du roc environnante est plus petit que la tension de l'échec admissible et que les tunnels sont stables. De plus, les régions avec potentialité instable ont été identifiées étant donné les résultats de 2D analyse non - élastique, et après que l'instabilité se soit produite aux régions prédites par le modèle, il a été arrêté jusqu'à la limite de la tension admissible à travers installer du support supplémentaire.

Jan 1, 2003

By A. Esterhuizen

Since 2005 Two Rivers Platinum Mine has set out on an initiative to actively monitor and control ground conditions on a daily basis, by making use of borehole cameras and pro-actively amending the support and mining strategies based on day-to-day observations of the hangingwall conditions. Today the borehole camera observations form part of the Rock Engineering Department?s daily function, and the size and frequency of falls of ground and ensuing accident rates have been drastically reduced since implementation of the system. The Two Rivers Platinum fall-of-ground management system aims to support 100% of the possible fallout thickness, based on ongoing data gathering and interpretation, thereby ensuring safety and limiting support cost.

Jan 1, 2014

By N. Mulaudzi

The use of SO2/air gas mixtures as an oxidant to precipitate Mn from Co(II) leach liquors was investigated. The effects of SO2/air ratio, pH and temperature on Mn precipitation were evaluated. It was found that the use of SO2/air gas mixtures resulted in significantly higher Mn precipitation kinetics compared to using air or pure O2 alone. The SO2/air ratio was varied from 0% to 6% SO2(v/v) in air and similar Mn removals were achieved at 0.75% to 3% SO2 at pH 3. The solution pH was varied from pH 2 to pH 4; Mn precipitation did not increase considerably from pH 2 to pH 3, but increased significantly at pH values higher than pH 3. Cobalt co-precipitation also increased as pH increased, with 1% Co co-precipitation at pH 3. An increase in temperature from 30°C to 60°C also increased Mn precipitation and 100% Mn precipitated at 50°C. Cobalt co-precipitation also increased significantly with an increase in temperature. An activation energy of 25 kJ/mol was calculated from the Arrhenius plot, which is an indication that the precipitation reactions were both chemically and diffusion controlled. XRD analysis showed that Mn precipitated in the form of Mn2O3 instead of MnO2 that was predicted from thermodynamic data. SEM and XRD analysis also revealed that the precipitate consisted mainly of gypsum or bassanite (99%), with the Mn containing phase (< 1%) distributed within the gypsum phase. The co-precipitated Co reported to the Mn phase. Keywords: manganese precipitation; SO2/O2 gas mixtures; cobalt solutions.

Jan 1, 2009

By R. J. Mason

Background to the Transvaal Iron Age-new discoveries at Olifantspoort and Broederstroom R. J. MASON*, Ph.D. (Visitor) The work being done on Iron Age sites in the Transvaal is described, with particular reference to the finds at Olifantspoort and Broederstroom. The material so far found provides evidence for the production of iron and copper, the farming of cattle and sheep, and the construction of large villages by people who were probably ancestral to the present Bantu population. The material dates from as early as A.D. 270, but clear indications occur from AD. 460 onwards.

Jan 1, 1974

By F. T. Cawood, M. N. M. Cudjoe

The ability to conduct real-time material tracking in mines has been a long-standing challenge. Technological innovations such as radio frequency identification technology (RFID) have over the years contributed to the effective tracking of material flow and reporting of metal content. This paper outlines the laboratory procedures and results from testing the suitability of microdot technology as a viable technique for real-time material tracking in mining. The paper clarifies the reasons for conducting the test and presents the material safety data sheet (MSDS) from a South African and Canadian perspective. Microdots from three aerosol systems were immersed in water, heated to 100°C, and crushed into coarse and fine material. These tests were used to ascertain if the technology could withstand mining conditions. A strength, weakness, opportunity, and threat (SWOT) analysis was used to evaluate and compare microdot technology with RFID. It was shown that microdot technology has some potential to track ore parcels because data integrity was retained after exposure to post-blast mining conditions. However, more improvement is required to digitally detect microdots before the technology can be implemented at scale in the mining industry.

Apr 2, 2022

By George Kayesa

[ ] A multiple-bench slope failure occurred at Letlhakane mine on 14th July 2005. No injuries or damage to equipment was suffered and mining production was not affected. Slope failure was preceded by the precursors of tension crack formation, crack widening and extension as well as slope monitoring targets movement. It was predicted that slope failure was imminent using the Geomos slope monitoring system, though the timing was not certain. The area to be affected by the slope failure was also known before hand as was the slope failure mode. As a result, measures were taken to avoid exposing personnel and mining equipment to the slope failure risk. This paper discusses how the prediction of the slope failure of 14th July 2005 using the Geomos slope monitoring system resulted into avoiding potentially fatal injury, damage to mining equipment and loss of mining production.

Jan 1, 2006

Alluvial diamond deposits covered with a thick overburden cannot be explored effectively and mined profitably with the available conventional techniques. A novel directional drilling technique has been developed and site trials have been conducted at the De Beers Namaqualand Mines situated at the western coast of South Africa. This paper describes the technique developed as well as the results of the site trials. The main task of the project is to develop a tool and a supporting system to achieve a remote exploration and ore extraction method for inaccessible alluvial diamond deposits. The project involves the acquisition of a system, commissioning on-site and evaluating the information obtained during assessment. The project consists of the design -of certain tools and instrumentation for the system, investigations and desktop studies as well as development of the system&apos;s logistics. The operating philosophy of the system is based on the keyhole surgery principle. In this study a pilot hole was drilled first, starting from the surface with an inclination to reach deeply seated diamondiferous gravel layers, followed by drilling into a more or less horizontal gravel layer for a certain length and finally pointing-upwards reaching ground surface at a predetermined exit point. The pilot drill bit was then replaced with a larger diameter reamer/mining tool and an HDPE tail pipe was attached behind the reamer. The drill string was retracted back to enlarge the guide hole and flush the excavated ore to the surface through the tail pipe. The material flow in between the sections of the system was&apos; carefully measured to assess and record the gravel recovery rates. Several horizontal holes were drilled at preplanned drill paths to reach and follow the ore layer and the Ore extraction was achieved by means of a reamer/mining tool. Principles of the concept have been proven viable in this investigation.

Jan 1, 2010

Mixed integer programming (MIP) has been used for optimizing production schedules of mines since the 1960s and is recognized a shaving significant potential for optimizing production scheduling problems for both surface and underground mining. The major problem in long-term production scheduling for underground orebodies generally relate to the large number of variables needed to formulate a MIP model, which makes it too complex to solve. As the number of variables in the model increase, solution times are known to increase at an exponential rate. In many instances the more extensive use of MIP models has been limited due to excessive solution times.

Jan 1, 2010

The exciting history of gold mining in South Africa haR been told in many different ways - in books, plays, and films, and on radio. But now, there&apos;s a new and far more lively way to find out about it and that is by actually participating in living history. Your invitation to go back in time will not take you much further from the centre of Johannesburg than the late-afternoon stretch of the shadows of the skyscrapers. The Gold Mine Museum - a new venture by the Chamber of Mines - brings back all the colour and romance of mining a century ago, and reminders of some of the hardships too. This is not an ordinary museum, but one of the most modem attempts in the world to make the past come to life.

Jan 1, 1980

In a gold CIP/CIL circuit, adding new circuit water to a final tails thickener and then directing the thickener overflow to the head of the circuit significantly reduces the cyanide concentration at the TSF discharge spigot. The new water is used to dilute the final tails. The dilution and recycle of the tails in this manner may have the added benefit of reducing reagent consumption, in some cases to the point where the reagent savings justify the expenditure and Cyanide Code compliance is achieved at no extra cost. Potential circuit configurations and water recycles can be modelled by splicing a flowsheeting and thermodynamics package, such that changes to the composition of the water can be reduced to chemical speciation with a Gibbs free energy minimisation enabling a complete understanding of the circuit water chemistry.

Jan 1, 2007