Search Documents

By J. J. Van Rensburg

The commissioning of a test facility for the calibration of anemometers by J. J. VAN RENSBURG (Student Member). After the erection of a commercially produced open-jet wind tunnel for the calibration of the anemometers used in mine ventilation, the wind tunnel was calibrated for routine use. There is a choice of five orifice plates. which, together with a variable-speed fan, can give a measurable range of air velocities in the test section from about 0,05 to 35 m/so The orifice plates were calibrated against a standard pitot tube, and it is now necessary only to measure the pressure drop across an orifice plate and to read off, from a set of graphs, the true outlet velocity in the test section. The paper describes the underlying theory and the test results.

Jan 4, 1975

By K. I. Afewu, L. C. Woollacott

Little is reported in the literature that is directly useful for the interpolation film coefficients for the in-pulp adsorption circuits used in gold metallurgy. This can create a problem if the design or operation of these circuits is to be optimized by the use of simulation techniques. To address this problem, a study was undertaken on the influence of mixing intensity, scale, and geometry on the film coefficient in adsorption systems typical of the carbon-in pulp plants used for gold extraction. This, the first paper deals with the influence of these factors on the film coefficient and shows that the specific power to just disperse the carbon in the slurry is an important variable. This variable is also strongly dependent on mixing intensity, scale, and geometry-a dependence that is dealt with in the second paper in the series. From the informatlon obtained, practical scale-up procedures were developed. These procedures are considered to be applicable to resin-in-pulp as well as to carbon-In-pulp plants.

Jan 1, 1995

By L. C. Woollacott

Some of the factors that may influence the reliability of a consistent material balance derived from plant data were investigated, data taken from a sampling of the Iow-grade tin-flotation circuit at Rooiberg A Mine being used as the basis for the investigation. The importance of subjecting a calculated balance to a thorough analysis of its sensitivity to erors in assay and flow rate measurements is highlighted. Several simple guidelines are derived from the analysis of the Rooiberg data, and these appear to be generaly applicable to process-evaluation exercises and to the technique used for the smoothing of material balances.

Jan 1, 1987

By J. M. Stewart, C. H. Wyndham

Suggested thermal stress limits for safe physiological strain in underground environments by J. M. STEW ART M.Sc. (Eng) (Witwatersrand) (Visitor) and C. H. WYNDHAM M.B., D.Sc. (Witwatersrand), F.R.C.P. (Land) (Fellow) A comparison of safe temperature limits, based on Mitchell and Whillier's equations for specific cooling power (SCP), with similar limits determined experimentally shows the SCP-based limits to be unnecessarily conservative. It is argued that, while a small part of this conservatism may be attributed to an erroneous extrapolation of the heat transfer dependence on wind speed, the major part is probably due to the use of too Iowa limiting mean skin temperature in the calculation of SCP. A combination of Mitche/l's basic data with results available in the literature permits the derivation of modified heat transfer equations based on data that fully cover the range of wind speeds of interest. These equations, using a mean skin temperature of 36°C as the basis for the calculation of safe temperature limits, are then shown to agree favourably with those determined empirically. Furthermore, values of SCP based on these equations are shown to correlate reasonably well with wet kata readings, giving positive support to the wet kata thermometer as a heat stress meter.

Jan 8, 1975

"Pressure leaching is an option for copper recovery from chalcopyrite. Leaching takes place at high temperatures and pressures in the presence of an oxidizing agent. This work shows how the performance of pressure leaching circuits may be improved by optimizing the configuration of autoclaves and the heat removal method. The objective was achieved by creating an autoclave model that combines mass balances, energy balances, and population balances. A base case circuit consisting of a single autoclave was chosen, and this base case was compared with options for increasing capacity by adding more autoclaves to the circuit. These capacity increase options include circuits in which the additional autoclave is added in parallel, in series, and in series with thickening between the two autoclaves. The copper extraction, productivity, and cooling requirements for these options are compared. The series circuit with interstage thickening has the highest extraction and productivity; however, the cooling duty in the first autoclave is high. In addition to comparing circuit options, three options for heat removal were investigated: cooling coils, quench water, and flash recycling. The flash recycle option results in the highest copper extraction, and the quench water option the lowest copper extraction. IntroductionBackgroundCopper sulphide ores and concentrates containing chalcopyrite are typically hard to leach under atmospheric conditions. Smelting of these ores may also be a challenge, due to the inability of smelting processes to handle low-grade ores, as well as impurities such as arsenic and antimony. Alternative hydrometallurgical routes to treating chalcopyrite are therefore required. One option is pressure leaching, which is the focus of this work.In the pressure leaching process, sulphide ores and concentrates are leached in autoclaves at temperatures of 200 to 220°C and a pressure of about 3000 kPa (Schlesinger et al., 2011). An oxidizing agent, usually oxygen, is required to oxidize sulphide ions to sulphate ions. The oxidation of sulphur to sulphate is exothermic; consequently, a method of heat removal is necessary in order to maintain the temperature in the autoclave."

Jan 1, 2016

PREFACE During the past year, considerable effort was devoted to the implementation of the strategic plan that was adopted by the SAIMM in 1986. Good progress was made in a number of areas, while in others the foundation was laid for future progress. Key Objective of the Institute The key objective of the SAIMM is as follows: To identify the needs of its members and to initiate and give effect to the means whereby the requirements for technology and scientific knowledge of the minerals and metals section of the South African economy are satisfied; and to represent and promote the interests of its members.

Jan 1, 1987

By J. O. Jensen

A method is described for the determination of cyanide in gold slurries, based on amperometry. The measured current is proportional to the concentration of cyanide, and is not effected by pH or by the concentration of oxygen in solution. It is also unaffected by other ions that may be present in gold-leaching solutions, including sulphide, thiocyanate, and thiosulphate. The current depends on the temperature, and an activation energy of 17,9 kJ/mol was determined Since the current is controlled by the mass transfer of cyanide to the anode, it depends on the conditions of agitation. In tests on an operational gold plant, slurry was pumped directly from the top of the leaching tank, through the measuring cell and back into the tank. The results indicate that the instrument is a promising alternative to the instruments currently available. The readings from the instrument remained in calibration for at least two days, showing that the instrument would need to be re-calibrated by the operating staff at regular periods.

Jan 1, 1994

By M. B. Algeo, R. H. A. Plaistowe

A method of forecasting the haulage trucks required for a large open-pit operation is described. Emphasis is placed on the effects of changes in planning and on the complexities of a mining operation that involves many benches and dumping areas.

Jan 1, 1979

By P. J. D. Lloyd

An account is given of the development of a process to concentrate gold and other valuable minerals and to produce a discardable waste. In this process, the ore is coarsely milled, a bulk flotation concentrate is prepared, and the flotation tailing is scavenged in a hydrocyclone, which returns coarse gangue, moderately coarse valuable minerals, and locked valuable minerals back to the mill. The engineering developments required by this circuit in order that it will fit underground, and the progress made towards the achievement of those requirements, are reviewed. If the waste is to be suitable for use as a backfill in a deep-level, flat tabular excavation, it should be capable of being placed hydraulically, and should have both low voidage and high rates of drainage. Such a material could be prepared by the fine screening of the overflow from the cyclone in the proposed circuit. Possible methods for the handling of the concentrate and the recovery of its valuable constituents are described. The paper concludes with a discussion of the possible benefits from the use, in deep-level Witwatersrand mines, of a system involving concentration underground, extensive backfilling using the tailings from the concentration process, and hydraulic hoisting of the concentrate.

Jan 1, 1979

By J. P. M. Hojem, C. Dimitriou, N. C. Joughin

This paper describes the design and construction of the first experimental underground rockcutting machine from measurements of cutting forces determined in tests on small rock specimens in the workshop. The deficiencies of this design, revealed by stoping with almost identical rockcutting machines, are described. An account is given of the design and construction of further experimental machines incorporating substantial improvements which made them technically feasible for use in production.

By R. D. Hancock

The loading and selective properties of a number of commercial and experimental resins developed for the extraction of base metals were evaluated. Particular applications that ",:ere considered included the extraction of copper from artificial dump liquors, the treatment of Iow-grade copper, nickel, and cobalt liquors, and the removal of nickel from a cobalt electrolyte. Reagents that showed promise were two experimental resins developed at Mintek containing pyridyl imidazole active groups and two Dow resins, XF4195 and XF4196.

Jan 1, 1982

By J. Danoczi

South Africa is running out of fresh water and is looking at ways to improve water usage. This report addresses how a diamond mine in Gauteng has improved the utilization of its water resources. In the past, water from the local river was deemed the most suitable to use in the grease recovery plant but subsequent tests on the water from the slimes dam have shows that this water source is in fact more suitable for diamond recovery. Utilizing the slimes dam water provides a more stable water source than the local river while also reducing the impact of the mine on the water resources in the area.

Jan 1, 2008

By J. N. van de Merwe

CONTRIBUTION BYH. WAGNER AND T.T. OZAN The paper by Dr J.N. van der Merwe makes an important contribution to the design of bord-and-pillar workings in the Vaal basin. It has been recognised for some time that the strength of coal seams in the Vaal basin is markedly lower than that of coal seams in other coal-mining districts in South Africa. However, there was insufficient data to quantify how much weaker the extensively jointed coal the Vaal basin is. A number of recent pillar collapses that occurred at Sigma colliery, the only remaining underground colliery in the Vaal basin, provided Dr Van der Merwe with an opportunity to make this assessment.

Jan 1, 1993

By G. M. Brown, B. J. Ebacher, W. G. Koellner

Introduction There is a continual economic push to increase the productivity of mobile material handling equipment used in open pit mines. This includes the largest electrical machines: excavators (draglines and shovels) and haul trucks (Figure 1). Existing DC drive systems used on this type of equipment are a mature technology. They have no further economic potential to accommodate larger equipment be-cause of the high maintenance costs and the trade-off between power, speed and space limitations of their DC traction mo-tors. In recent years the large-scale introduction of AC drives in the rail transportation sector1,and the availability of poworful GTO and IGBT modules have led to the devolopment of compact, powerful, an drugged AC inverter drives specifically adapted to the mining market2,3. The major advantage of AC drives stems from the squirrel cage induction motor which eliminates the DC commutator. This leads directly to higher speed, increased power density, higher reliability, greater efficiency and lower maintenance of the traction motors. In the context of excavators and haul trucks, additional benofits driving the move to AC are (i) increased production rate due to higher machine speed, and power density, (ii) increased reliability and lower cost inverters using 3.3 kV IGBT's, (iii) active front-end (AFE) technology that improves compatibility with the mine power grid and an proved dynamic response,(iv) intelligent converter design that provides increased fault tolerance, (v) contextual maintenance software that facilitates trouble-shooting, and (vi) remote diagnostic capabilities. This paper describes how these and other features of AC drives lead to higher productivity in mining shovels, draglines, and haul trucks. Minimize the cost per ton of material moved The overall goal that drives design and sales of excavators and haul trucks is the constant requirement to reduce the cost per ton of material moved. Whether this involves blasting, loading trucks, or hauling material to the crusher or waste dump, equipment that reduces the cost per ton of material moved contributes to a more profitable operation. An accurate determination of the true cost per ton to move material must consider every aspect of the equipment and the circumstances under which it is used. Procurement and capital costs, fuel, operating, and maintenance costs over the useful life, and eventually the cost of scrapping should all be taken into account to determine the real cost per ton of moving material. We will focus on two broad areas that relate to the equipment itself; factors influencing the amount of material moved (Table I) and factors influencing the cost of material moved (Table II). Emphasis will be given to those elements in the tables that most influence the productivity of excavators and haul trucks due to the application of AC drive technology. Maximize the amount of material moved Maximize production rate he production rate refers to the quantity of material that can be loaded or moved per hour. This generally involves larger, faster, and more powerful equipment that operates more reliably to minimize down-time. AC motors Figure 2 compares the hoist motor speed-torque response of two 77 t (85 short ton) shovels, one AC the other DC. The absence of commutation limits on the AC motors enables the AC shovel to operate with a greater area under the speed-torque curve, resulting in faster lowering speeds and reduced times for the swing to return to the pit. This is especially important for short swing angles where the operator may have to wait for the dipper to lower. Reducing the cycle time by 6 to 8 seconds at the shovel translates into an increase in shovel production of about 20%. Larger equipment The bucket capacity of excavators has increased approximately 100-fold over the last century. Figure 3

Sep 1, 2001

By R. S. Sanders, J. Schaan

Syncrude Canada Ltd. produces synthetic crude oil from Canada?s vast oil sand reserves by mining the oil sand, then separating and upgrading the ultra-viscous crude oil, or bitumen (~ 106mPa s @ 10ºC). At Syncrude?s Aurora Mine, about 16 000 tonnes oil sand per hour are mined and then transported 5 km by slurry pipeline to the extraction plant. The waste tailings stream is then transported about10 km by pipeline to a settling/sand storage basin. Oil sand slurries are reasonably concentrated (> 35%solids by volume), typically have a sand particle diameter between 0.18 and 0.3 mm, and are transported at reasonably high velocities (3 to 5.5 m/s). As one would expect, pipeline wear is a significant problem in this industry, in terms of both unplanned production outages and maintenance costs. In order to develop strategies to extend pipe life and to focus more on condition-based maintenance scheduling (as opposed to preventative maintenance), Syncrude has implemented an ongoing pipe wear measurement programme. Regular measurements of pipe wall thickness are obtained at various circumferential positions at a number of axial locations along each pipeline, using an ultrasonic scanning technique. In this paper, we show how wear rates vary as a function of axial location and circumferential position for oil sand hydro transport and coarse particle tailings pipelines. The specific positions at which peak wear rates occur are explained by considering the characteristics of the coarse particle slurry flows to which the pipelines are exposed.

Jan 1, 2007

"Coal seam gas problems can adversely affect the safety and productivity of underground coal mines, leading to fatalities and financial losses. Conventional gas management technologies using ventilation and gas drainage are unable to deal with the high and irregular gas emissions associated with high-production longwall mining. New technologies need to be developed to supplement the traditional gas management techniques to minimize the hazard of coal seam gas. Thin spray-on liners (TSLs) have gained some success for rock surface support since their introduction to the mining industry. Due to their relatively low permeability and appropriate mechanical properties, TSLs also show potential to be used as a gas management tool in underground coal mines.In this paper we review the current gas management challenges and discuss the potential use of TSLs as a gas management tool in underground coal mines. This may involve reducing gas migration into the excavations/roadways, enhancing in-seam gas drainage, and preventing spontaneous combustion. Some potential areas for future research work are identified. IntroductionWhen a coal seam is influenced by mining activities, gas stored inside is liberated into the underground ventilation system. Gas emissions have created serious difficulties for the coal mining industry around the world. Therefore, coal mines have to develop effective strategies to control the gas concentration below the threshold value to meet statutory requirements. Ventilation has been the first solution in gas management for underground coal mining. When the emitted gas cannot be effectively diluted by ventilated air, gas drainage using pre- and/or post-drainage has to be introduced. However, even with ventilation and gas drainage, irregular gas emissions usually increase the gas concentration in roadways and slow down the development rate, thus causing significant economic loss to the coal mining industry (Thakur, 2006). Therefore, new technologies need to be developed to address this issue and mitigate the explosion risk."

Jan 1, 2016

By N. C. Joughin, A. C. Buckmaster

The use of face conveyors in gold mines by N. C. JOUGHIN. B.Sc. (Eng.). Ph.D. (Wits) (Member) and A. C. BUCKMASTER; M.A. (Cantab.) A mechanized stope-cleaning system has been developed around an armoured face conveyor, which was tested on the surface and in two underground trials. In the second underground trial, an average face advance of 8,5 m per month was obtained with a labour productivity of 27 ca/worker/month on a two-shift blast cycle. Two new face cleaning systems have been built, each incorporating an armoured face conveyor, a loading plough, a collapsible self-advancing barricade, and an integral roof-support system. These are about to be tested. A new type of reciprocating flight conveyor is being developed for stope use. This is cheaper, lighter, and more compact, and exhibits better wear characteristics, than an armoured face conveyor. In the early stages of the trials, this conveyor frequently achieved a singleshift blast cycle. It should be possible to achieve face advances of up to 40 ca/worker/month with a consistent one-shift blast cycle. The use of drill rigs and a self-advancing roof-support system would improve the productivity to over 50 ca/worker/month.

Jan 2, 1976

By L. Hermansson

Trackless mining at LKAB, Sweden by L HERMANSSON (Visitor) Because the usual means of transporting men and material to the working sites was time-wasting and uneconomical, inclined subways were installed in the Kiirunavaara Mine that permitted the access of rubber-wheeled vehicles to all underground working sites. Men and material could now be transported direct to the working site with no reloading. An increase of 8 to 12 per cent in underground productivity has been obtained by the use of this new transportation system. Rubber-wheeled vehicles are also used in development, production drilling, and loading. In December 1958, the management of the Luossavaara Mine decided to cut the costs of waste-rock haulage. The system of waste transport was the conventional one of shuttle car, rail haulage, and skip hoisting. After consideration of other methods, it was decided to re-equip the mine completely for a system of trackless transport. Results show that mining costs per ton of ore were reduced by 27 per cent, and mining costs per ton of waste were reduced by a spectacular 80 per cent. The new system has proved to be more flexible, and ore grading has been simplified since there is no longer any mixing in ore passes and chutes.

By C. S. Northcote, I. F. Buchan, L. F. Baars

In 1969 the Coal Division of the Anglo American Corporation was awarded the tender to supply coal to the new 3000 MW power station to be erected at Kriel, which is situated midway between the towns of Ogies and Bethal in the eastern Transvaal. The coal was to be supplied from the No. 4 Seam in the Kriel Area of the Witbank Coalfield. The No. 4 Seam in this area varies in depth of overburden from 75 m to 6 m, with an average of 55 m. Initially, the mine was planned as an underground mine incorporating a three-shaft system for transporting some 8 million tons of coal per annum to the power station. As the result of negotiations between Anglo and Escom to improve the volumetric extraction of coal from the new mine, the Kriel Division of Anglo Power Collieries was finally planned to produce 4,1 million tons of coal from an underground mine and 4,5 million tons from an opencast mine, with a resultant increase in volumetric extraction. This paper describes the opencast operation at Kriel, with particular reference to the water problems encountered and to the operation of the draglines on sloping ground to a depth of 40 m to the top of the coal seam.

Jan 1, 1980

By S. A. C. Liedberg, M. H. Fricker

The conference was divided into a total of 12 different sessions. Apart from the keynote addresses, the papers covered many aspects of open-pit mining, from mine design and blasting techniques to mining operations and equipment, as well as water management and rehabilitation. A number of case studies were also presented. Most of the 68 papers originated from Australia; however, presentations were also made by representatives from Chile, Indonesia, Papua New Guinea, and South Africa. The keynote papers dealt with subjects such as the economics of open pits, project planning of a new large copper deposit, management principles, and rehabilitation strategies.

Jan 1, 1993