Search Documents

By G. Chisakuta, P. Bwando, G. Mitshabu

By the end of 2022, the south-eastern Copper Belt region of the Democratic Republic of Congo was host to more than 40 small, medium, and relatively large sized copper solvent extraction sites. To date, solvent extraction reagents supplied in this region have never exceeded 50% of ketoxime content. We generated laboratory extraction and strip isotherms and used these with the BASF IsocalcTM modelling software to assess the benefit of using higher ketoxime blends on the main metallurgical performance indicators such as copper recovery and net transfer. Pure ketoxime extractants combine a relatively low strip point and a decent loading capacity, which are most effective as the pH of the pregnant leach solution gets closer to 2.

Jan 1, 2023

By J. N. Van der Merwe

Following the Coalbrook disaster in 1960, research into coal pillar strength resulted in the adoption of the concept of a safety factor for the design of stable pillars in South African coal mining. At the time when the original statistical analysis was performed by Salamon and Munro in the early 1960s, 27 cases of failed pillar workings were considered suitable for inclusion in the database of failed pillars. Pillar failure did not stop after the introduction of the safety factor formula by Salamon and Munro (1967). In the ensuing years, pillars that were created before the application of the formula deteriorated and later failed, as did ones that were created after the introduction of the formula. This means that over time, the database of failed pillar cases increased in size, allowing ever more reliable analyses to be performed. The number of failed cases in the database had grown from the original 27 in the 1960s to 86 by 2011. All the failed cases are contained in the updated database. The database of stable pillars, which is also used in the derivation of strength formulae, has now been extended from 125 to 337 cases. The new database of intact pillar cases is more complete as it bridges the time gap between the Salamon and Munro (1967) and the Van der Merwe (2006) databases. The original requirements for inclusion into the database were satisfied in the compilation of this latest collection. The characteristics of the original database of intact pillars did not change in a meaningful way. The mining depth and pillar dimensions of the new database are largely as they were in the original database. Time-related trends with regard to pillar dimensions and depth of mining could not be found, indicating that the geometrical parameters of coal mining in South Africa have not changed meaningfully in approximately a century of mining. The characteristics of cases in the updated database of failed pillars does not differ substantially from the one published by Van der Merwe (2006). The same difference between that database and the original Salamon and Munro database, namely that the average safety factor of the failed cases had increased dramatically, from 1.0 to 1.5, is still apparent. This may be due to the inclusion of more failures from specific areas that exhibit a disproportionate number of failures at higher safety factors. These areas are the Vaal Basin, Klip River, and Free State coalfields. The new database confirms yet again that there is no correlation between the safety factors of failed pillars and their time of failure. The safety factor on its own is thus not a reliable predictor of longterm stability of pillars. Keywords coal pillar, stable pillar cases, pillar collapse, pillar data base.

Nov 1, 2013

The Annual General Meeting of the Institute was held in Kelvin House, Johannesburg, on Wednesday, 26th August, 1970, at 4.15 p.m. Mr. J. K. E. Douglas (President) was in the Chair. There were also present sixty-three Fellows, thirty-five Members, one Graduate, eight Associates, five Students and nineteen Visitors, making a total of one hundred and thirty-two. The President declared the meeting open at 4.20 p.m. OBITUARIES The President: 'It is my sad duty to announce the deaths of the following members of the Institute. Dr J. A. Papenfus, Fellow, who joined the Institute in 1942 and passed away on the 28th of May, 1970. Mr D. G. Beadle, Fellow, who joined the Institute in 1946 and passed away on the 17th of June, 1970. Gentlemen, Derek Beadle was very well known in this Institute. His papers on dust will be remembered and, at the time of his untimely death, he was one of our assistant editors. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, I would ask you to rise and observe a few moments' silence.' MINUTES The President: 'May we confirm the minutes of the General Meeting held on 15th April, 1970, as published in the July, 1970, issue of the Journal'. Agreed. WELCOME TO VISITORS The President: 'Ladies and Gentlemen, we are honoured this afternoon by the presence of many distinguished guests and I extend to you all a most cordial welcome. We are happy to have with us Dr A. A. von Maltitz, President of the Chamber of Mines of South Africa, who is also Honorary President of this Institute. We also have one of our Honorary Vice- Presidents, Mr T. L. Gibbs, the Government Mining Engineer; Mr D. E. Hamm, President, Institution of Certificated Mechanical and Electrical Engineers, S.A.; Mr S. C. M. Naude, Director, Witwatersrand Technical College; Mr I. R. G. Stephen, Senior Vice-President, The S.A. Institute of Electrical Engineers; Mr G. M. Tompkins, President, The S.A. Institution of Mechanical Engineers; Professor P. B. Ackermann, President of the Geological Society of S.A.; Mr A. S. Robinson, Vice-President of the S.A. Institute of Civil Engineers; Professor W. Mare, President of the Institute of Land Surveyors of the Transvaal; Mr B. D. Charlton, President of the S.A. Institute of Assayers and Analysts; Mr R. Hemp, The President, The Mine Ventilation Society of S.A.; Mr L. J. Prince, The President, The S.A. Association of Mine Managers; Mr J. Botha, The President, The S.A. Institute of Foundrymen; Mr G. Niterl, The President, The Institute of Welding; Mr M. R. Gericke, President, S.A. Council of Professional Engineers; Mr N. A. Honnet, Chairman, Orange Free State Branch; Mr P. R. C. Cooke, Chairman. The South African Chemical Institute (S. Tvl' Section). Gentlemen, we are very honoured indeed, to have these distinguished gentlemen with us this afternoon, as our honoured guests. We are also pleased to have with us, one of our Honorary Fellows, Mr F. G. Hill, and several Past-Presidents. I also extend a very warm welcome to all our lady guests and to all our other visitors.' MEMBERSHIP The President: 'I have pleasure in announcing that the names of the following candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership in the following grades: NEW APPLICATIONS Fellows: Herbert Dalton-Brown, Stephen William Morel. Members: Clive Lester Workman-Davies, Basil James Russell Botha. Students: Timothy Nigel Watson, John William Hairbottle. I wish to welcome the new members to the Institute and to congratulate those members who have been transferred to a higher grade.' ANNUAL REPORTOFTHE COUNCILAND ACCOUNTS FOR THE YEAR ENDED 30th JUNE, 1970 The President: 'I now have pleasure in presenting to you, the Annual Report and Statement of Accounts for the year ended June, 1970. These have been handed to you this afternoon and, as is customary, I propose they be taken as read. Before moving their adoption, however, I would like to refer to some of the salient features, leaving as is usual, the task of dealing with the finances, to our Honorary Treasurer. It is encouraging that membership has continued to grow, and now stands at 1,613, an increase of 61 over last year's total. Your Council, however, is aware that there are still people in our mining and metallurgical industries, who could qualify for membership, but who have not yet joined the Institute. A drive to increase membership was accordingly organised, and members of Council were given the responsibility for campaigning in sections of industry, and for publicising the objectives and advantages of belonging to the Institute. Up to now there has not been much reaction to this campaign, but I hope we will see results in the coming year. At the same time, Council has recognised the need for change in the conduct of the Institute's affairs in order to meet the changing needs of our membership. Our members, both mining and metallurgical, are in the first place, geographically more widely dispersed than they used to be, and secondly, with the growth of the metallurgical industry, their technical interests are now more diversified. The Institute must cope with these changing needs if we are to continue to perform a useful function. The

The Annual General Meeting of the Institute was held in Kelvin House, Johannesburg, on Wednesday, 26th August, 1970, at 4.15 p.m. Mr. J. K. E. Douglas (President) was in the Chair. There were also present sixty-three Fellows, thirty-five Members, one Graduate, eight Associates, five Students and nineteen Visitors, making a total of one hundred and thirty-two. The President declared the meeting open at 4.20 p.m. OBITUARIES The President: 'It is my sad duty to announce the deaths of the following members of the Institute. Dr J. A. Papenfus, Fellow, who joined the Institute in 1942 and passed away on the 28th of May, 1970. Mr D. G. Beadle, Fellow, who joined the Institute in 1946 and passed away on the 17th of June, 1970. Gentlemen, Derek Beadle was very well known in this Institute. His papers on dust will be remembered and, at the time of his untimely death, he was one of our assistant editors. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, I would ask you to rise and observe a few moments' silence.' MINUTES The President: 'May we confirm the minutes of the General Meeting held on 15th April, 1970, as published in the July, 1970, issue of the Journal'. Agreed. WELCOME TO VISITORS The President: 'Ladies and Gentlemen, we are honoured this afternoon by the presence of many distinguished guests and I extend to you all a most cordial welcome. We are happy to have with us Dr A. A. von Maltitz, President of the Chamber of Mines of South Africa, who is also Honorary President of this Institute. We also have one of our Honorary Vice-Presidents, Mr T. L. Gibbs, the Government Mining Engineer; Mr D. E. Hamm, President, Institution of Certificated Mechanical and Electrical Engineers, S.A.; Mr S. C. M. Naude, Director, Witwatersrand Technical College; Mr I. R. G. Stephen, Senior Vice-President, The S.A. Institute of Electrical Engineers; Mr G. M. Tompkins, President, The S.A. Institution of Mechanical Engineers; Professor P. B. Ackermann, President of the Geological Society of S.A.; Mr A. S. Robinson, Vice-President of the S.A. Institute of Civil Engineers; Professor W. Mare, President of the Institute of Land Surveyors of the Transvaal; Mr B. D. Charlton, President of the S.A. Institute of Assayers and Analysts; Mr R. Hemp, The President, The Mine Ventilation Society of S.A.; Mr L. J. Prince, The President, The S.A. Association of Mine Managers; Mr J. Botha, The President, The S.A. Institute of Foundrymen; Mr G. Niterl, The President, The Institute of Welding; Mr M. R. Gericke, President, S.A. Council of Professional Engineers; Mr N. A. Honnet, Chairman, Orange Free State Branch; Mr P. R. C. Cooke, Chairman. The South African Chemical Institute (S. Tvl. Section). Gentlemen, we are very honoured indeed, to have these distinguished gentlemen with us this afternoon, as our honoured guests. We are also pleased to have with us, one of our Honorary Fellows, Mr F. G. Hill, and several Past-Presidents. I also extend a very warm welcome to all our lady guests and to all our other visitors.' MEMBERSHIP The President: 'I have pleasure in announcing that the names of the following candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership in the following grades: NEW APPLICATIONS Fellows: Herbert Dalton-Brown, Stephen William Morel. Members: Clive Lester Workman-Davies, Basil James Russell Botha. Students: Timothy Nigel Watson, John William Hair-bottle. I wish to welcome the new members to the Institute and to congratulate those members who have been transferred to a higher grade.' ANNUAL REPORTOFTHE COUNCILAND ACCOUNTS FOR THE YEAR ENDED 30th JUNE, 1970 The President: 'I now have pleasure in presenting to you, the Annual Report and Statement of Accounts for the year ended June, 1970. These have been handed to you this afternoon and, as is customary, I propose they be taken as read. Before moving their adoption, however, I would like to refer to some of the salient features, leaving as is usual, the task of dealing with the finances, to our Honorary Treasurer. It is encouraging that membership has continued to grow, and now stands at 1,613, an increase of 61 over last year's total. Your Council, however, is aware that there are still people in our mining and metallurgical industries, who could qualify for membership, but who have not yet joined the Institute. A drive to increase membership was accordingly organised, and members of Council were given the responsibility for campaigning in sections of industry, and for publicising the objectives and advantages of belonging to the Institute. Up to now there has not been much reaction to this campaign, but I hope we will see results in the coming year. At the same time, Council has recognised the need for change in the conduct of the Institute's affairs in order to meet the changing needs of our membership. Our members, both mining and metallurgical, are in the first place, geographically more widely dispersed than they used to be, and secondly, with the growth of the metallurgical industry, their technical interests are now more diversified. The Institute must cope with these changing needs if we are to continue to perform a useful function. The

By N. F. Mashinini

Optimization of current control systems, proper maintenance and efficient training of personnel are recommendations made to control the amount of dust that underground employees are exposed to on a daily basis in the coal mining industry. This dissertation forms as part of Sasol Mining?s commitment to protect the health and safety of their employees by suppressing and controlling dust at their mines. This study aims to understand the relationship among mining processes, exposure to dust and dust suppression control measures. The research phase of the project was done at the Sasol Mining Secunda complex where underground visits were undertaken to investigate current control systems and also new systems that are being implemented by Sasol Mining. This work was important because it helped determine the sources of dust underground and also to identify the shortcomings of current control systems and to test the efficiencies of the new systems implemented at Sasol Mining. The most important result of the research work was the identification of which underground operators were exposed the most to dust as this assisted in designing a dust suppression system for the areas where these operators worked. The main conclusions of this study are that the current control systems are sufficient for controlling dust and ensuring dust compliance if they are used efficiently and maintained properly.

Jan 1, 2008

By M. Paricheh, M. Rahmanpour

"The cost efficiency and high reliability of semi-mobile or combined in-pit crushing-conveying (IPCC) and truck systems, compared to conventional truck-shovel systems alone, make them more attractive for use in modern mining operations. Semi-mobile systems, which are the most common systems in open-pit mining, combine the advantages of both systems such that fewer trucks are required, operating costs are lowered, and the operation is environmentally sound. One major aspect of utilizing this system is determining the location of the in-pit crusher and the timing of relocations. Facility location models are rarely used in the mining sector, but these models may be used for solving the in-pit crusher location problem. To this end, the main parameters affecting the IPCC location in open pit mines are reviewed and examples given of how they are applied to a dynamic location-relocation problem. Subsequently, the model is implemented for Sungun copper mine in Iran and the number and the exact time of relocations of the IPCC units determined. IntroductionNowadays, compared to the last century, metal prices are more volatile, average and cut-off grades have decreased, and stripping ratios increased. From a mining engineering point of view, many ore deposits with simple access and low capital and operating costs have been exhausted. The remaining deposits are located at depth, with no easy access, which requires high initial capital costs (Osanloo, 2012). Mining at great depths and high tonnages is possible only through open pit mining. Today, more than 80% of open pit mines in the world use a shovel-truck system for loading-hauling operations (Osanloo, 2010).With increasing depth, haulage distances increase and the number of loads per truck decreases. As a result, fuel, tyre, and depreciation costs per ton increase. Owing to these factors, open pit mining at great depth (300 to 1000 m) using shovel-truck systems faces some technical and economic problems. In-pit crushing-conveying (IPCC) systems have been known in the mining industry for many decades. The idea was introduced in 1956 in Germany. Today, the cost efficiency and high reliability of IPCC make it more appealing than conventional shovel-truck operation, especially in longer life projects with lengthy transportation distances and high production rates (Koehler, 2003). Since 1956, different aspects of this system have been reviewed by many researchers. Barua and Lanergan (1985) developed a computer program that compares the tonnage aspects of various conveyor layouts. They believed that to maximize the economic benefit of lower haulage costs associated with in-pit conveying, one must first minimize the cost of the flatter slope, which is expressed in terms of additional stripping or tied-up ore. Dos Santos and Stanisic (1987) evaluated the design of a high-angle conveyor at the Majdanpek copper mine. Then, Sturgul (1987) applied GPSS (general purpose simulation system) to find the best location of an in-pit crusher."

Jan 1, 2017

By G. Chambovet

Applied geophysical methods such as the surface seismic method have been applied for many years and in many places, mainly for oil exploration and to a lesser extent for mineral deposits? exploration in sedimentary basins. The seismic method fundamental is based on the variations of acoustic impedance in a layered earth model and such variations at each main geological interface create reflected waves that are processed and imaged in order to output a clear picture of the subsurface structure. The geology of South Africa was historically, and even until recently, considered as unfit for seismic exploration and the mines were always reluctant to spend any portions of their exploration budgets on these techniques. Hard rocks and high P-waves velocities were creating quite a hopeless model for any mine geologist or geophysicist (if any), unsuitable for the proper use of seismic waves to image their subsurface problems. Boreholes were considered the only reliable tool to derive a geological image of the mine structural features and were linked sometimes with surface methods such as aero-magnetism. The obvious flaw of this methodology was the inability to derive a continuous image from a discrete set of measurement points. Surface 3D seismic is the tool that gives a reliable solution from the initial model extracted from the boreholes, as even the aero-magnetism mapping gives a flat image, unable to show any depth correlation from well to well. The first 3D surface seismic surveys were recorded in the early Nineties only for the gold mines of the Witwatersrand, after a series of serious new shaft sinking failures. The wrong geological locations of these shafts resulted in financial loss of several hundred million rands. The era of3D seismic just started in South Africa and till 1997, all seismic done in the country was for gold exploration with geological target depths close to the oil exploration average depth of investigation. A very important breakthrough was reached when the depth accuracy of the seismic image was tested in real scale as the stopes were surveyed. An error of amplitude of 20 m was usual when true depth was compared with the seismic image predicted depth and shape. This accuracy, completely unknown in oil exploration, started to gain supporters of seismic methods in the mining community but the cash problems and the concentration/disappearance of gold mines in the late Nineties, led to the belief that seismic would be just a very short exploration activity for the mining sector. ort exploration activity for the mining sector. But starting in 1998 with Impala, a tremendous and continuous 3D surface seismic activity occurred in the platinum mining sector. The seismic world got used to new terms such a Merensky and UG2, which have replaced the VCR and black reef. If the primary expectation of platinum surface 3D seismic was to determine and ascertain new shaft locations, as for the gold mines, the quality of seismic data led the mine geologists to require smaller and smaller imaging of geological objects. In addition to the main structural image, small faults, potholes, and shear zone were common expectations of platinum seismic. In a constant velocity environment, what saved the day was the sharp density contrast between the PGM reef and the embedding geology. A good contrast of impedance exists in the whole Bushveld and is sufficient to have enough reflected waves from the PGM main layers to build a high quality seismic image of the subsurface. Recent advances in technology have led in less than 10years to major improvements in the seismic acquisition by using high frequency vibrating seismic sources, but also in processing and interpretation. With these latest improvements, seismic can detect objects of 7.5 m size, either fault throws, flexures, etc. The PGM formations of the Eastern limb of the Bushveld Complex are now accessible for seismic imaging, with cost per square kilometre comparable to the borehole cost of the same surface unit. The economically acceptable seismic surveys can be used for UG2 structural imaging up to a depth of 210 m below surface. Linked with borehole information, 3D seismic today offers a wide range of information for mine development: structural imaging, small fault detection, pothole and shear zone identification. All users of 3D seismic have also used this technique as a tool in the process to qualify their mineral reserves and especially from the category ?inferred? to the category ?measured?. Junior mining companies, in the feasibility stage of their projects, are also quite eager to use seismic as a reserve certification tool, when they present financial statements to future potential investors. Junior mining companies, in the feasibility stage of their projects, are also quite eager to use seismic as a reserve certification tool, when they present financial statements to future potential investors. The current high demand on platinum, pushes the seismic towards new technologies to be implemented in order to improve the final image. Using surface and borehole seismic together or acquiring seismic surveys with multi-component receivers have been just introduced in South Africa. In less than 10 years, surface seismic by adapting its methods to the special case of the Bushveld, became a mandatory step in mine development and ore resources evaluation. As part of the ?seismic? world we are proud to be a major player the ?surge? of platinum exploration and production in these last years and we will certainly increase our synergy with the mine sectors in the exciting coming years.

Jan 1, 2006

By L. C. Woollacott, A. K. Tripathy, J. H. Potgieter

This paper presents the second of a two part study on density stratification in a laboratory batch jig. The first study, reported elsewhere, investigated the effect of operating conditions on the stratification profile achieved at equilibrium. The study reported in this paper investigated their effect on the kinetics of density stratification under 18 different sets of operating conditions - five for binary systems with different particle densities; and 13 for a ternary system with different configurations of the jig cycle. Although the study was academic in nature (it involved simple systems of 8 mm glass beads) it has a number of practical implications. It found that the most influential operating variables affecting stratification kinetics are the amplitude of water displacement, the pulsion hold time, and, to a lesser extent, the pulsion time. It also found that reasonable rates of stratification can be expected in systems with density differences as low as 237 kg/m3 but below this the kinetics deteriorate significantly. The two studies together suggest that, within a broad range of operating conditions, the equilibrium stratification profile is independent of control variables and it is the control of stratification kinetics that has the primary influence on the quality of density separations in a jig. Keywords: Jigging kinetics, stratification, equilibrium stratification, batch jig

Jan 1, 2020

By M. S. Shishvan, S. Klerkx, J. Sattarvand

The inaccurately drilled blastholes from the planned locations cause changes in the spatial distribution of explosive energy; some areas of the blast may receive a surplus of explosive energy, while others see a reduction. This results in less uniform fragmentation, reduces the efficiency of mining operations and increases costs. Additionally, it can lead to slope stability issues, flyrock, and uneven benches. To mitigate these problems, this study attempts to reduce differences in the explosive energy distribution (EED) through an optimization approach that adjusts the height of explosive columns in blastholes. Two optimization algorithms, the Genetic Algorithm (GA) and Tabu Search (TS), are tested. The latter is preferred for its local search neighbourhood strategy that gives superior computation times. Applications on different blast patterns result in improvements of 0.53–1.54%, or 2.14–3.94% when only the affected blocks are considered.

Sep 1, 2021

By J. N. Baloyi

"In atomic emission and atomic absorption spectrophotometry, the sample is heated to a high temperature and thereby decomposed into atoms and ions that absorb or emit visible or ultraviolet electromagnetic radiation at energies characteristic of the elements involved. The flame test is a very simple form of this technique. The yellowing of a flame by the addition of salt, for example, occurs because the sodium in salt emits strongly in the yellow portion of the visible spectrum. These methods are especially useful for low concentrations of metallic elements in both qualitative and quantitative analysis.Interference on Iep-OES has not always been considered a serious problem, especially in the beginning, when compared with Atomic Absorption Spectroscopy. This was due to the euphoria created by the new technique. It meant that criticism was subdued. The Iep was vastly superior to the Atomic Absorption technique, that the interferences suffered by the Atomic Absorption technique dwarfed the little interferences suffered by the rep-OES technique. This is how rep-OES has had a reputation as an interference free technique."

Jan 1, 2014

By P. K. Jain

A spiral concentrator is a density separation device used for the beneficiation of coal and various minerals such as iron ore, chromite ore, gold, beach sand minerals etc. The flow pattern developed in the equipment is complex and unique, yet the operation is very simple, with low capital and operating expenditure. Spirals are applied for beneficiation of material in the size range finer than 2 mm and are capable of recovering heavy minerals as fine as .01 mm. The understanding of the unique flow pattern has kept researchers engaged over the last few decades and attempts are being made to explain such flow patterns so that they can be controlled and modified to improve the operating efficiency, Ep (Ecart Probable Error, also known as probable error in separation) and acceptability of spiral concentrators for processing of fines and slimes - currently being discarded and dumped in the tailing ponds. An attempt has been made in this paper to explain the generation of complex flow patterns with application to classical solid mechanics in the fluid and slurry system. The same has been used to explain the selective separation of particles in different zones in a cross-section on the spiral trough. The paper also discusses the application of a force balance model to explain the generation of secondary circulation. Due to the presence of laminar and turbulent flow regimes in the spiral concentrator, varieties of equations have been proposed in the literature, consisting of different equations for different zones. An attempt has been made to present a unified flow equation for calculation of flow velocity at different positions on the spiral trough. Keywords: Secondary circulation, spiral concentrator, density separation, fine particle processing

Jan 1, 2020

By N. F. Dawson

Recovery of a chromite concentrate from UG2 flotation tailings streams, of a grade suitable for further pyrometallurgical treatment for the production of ferrochrome, has certain specific challenges not only by virtue of the decoupled nature of the primary PGM recovery process and secondary gravity based chromite recovery circuits, but also because of intrinsic variations in the nature of the ore and its mineral composition. Variability in the ore, together with upstream process dynamics, creates a challenging environment in which to achieve optimal recovery of a gravity concentrate with accurate grade control. This paper examines certain inter-relational aspects between the ore gangue and chromite mineral types, the influence of the primary PGM extraction circuit and secondary chromite extraction activity as applied specifically to UG2 ore against a background of actual plant experiences and circuit configurations applied in order achieve a suitable quality of chromite concentrate.

Jan 1, 2010

By B. P. Watson, D. P. Roberts, R. A. Lamos

The Upper Group 2 (UG2) chromitite reef is a shallow-dipping stratiform tabular orebody in the South African Bushveld Complex, which strikes for hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2 500 m. Pillars are widely used to support the open stopes and bords. Little work has been done in the past to determine the strength of pillars on the UG2 Reef and design was done using formulae developed for other hard-rock mines. This has led to oversized pillars with consequent sterilization of ore. In this paper we describe a back-analysis of stable and failed UG2 pillars on the Bushveld platinum mines, and provides a strength formula for UG2 pillars. The formula may be used cautiously on all Bushveld platinum mines with similar geotechnical, geometrical, and geomechanical conditions to the pillars in the database.

Aug 1, 2021

By S. Bradshaw, A. Mabentsela

"Physical and numerical modelling methods were followed to identify mechanism(s) for tundish slag entrainment in a bare tundish and one with a flow control device (FCD).The physical and numerical models made use of water and paraffin to model steel and slag respectively. Observations from the physical model showed that the steel-slag interface remains immobile in both cases. Entrained paraffin formed droplets approximately 1 mm in diameter. Results from both models (numerical and physical) showed that in both cases (bare and FCD case), areas of high entrained slag concentration exist near the inlet region. The entrained slag concentration decreases towards the tundish endwalls.Flow patterns and velocities tangential to the steel-slag interface from the numerical model showed that slag entrainment in both the bare tundish and tundish with a FCD possibly takes place via two mechanisms. First, the slag moves across the steel-slag interface via mass transfer; secondly small velocities tangential to the interface at depths greater than 10 mm below the interface carry the already ‘entrained’ slag into the bulk steel phase. These tangential flow patterns are dominant in the inlet region, hence the high concentration of entrained slag in this region. IntroductionThe tundish serves as the last metallurgical vessel through which steel passes before solidifying in the moulds. It is in the tundish that the last traces of non-metallic inclusions should be removed, otherwise the inclusions carry over to the moulds and cause defects in the steel product. In the tundish, the slag is less dense than the melt and thus resides on the top of the melt. The slag provides a sink into which the non-metallic inclusions float to and dissolve. The slag also protects the melt from air and heat loss. However, when slag is entrained in the melt as a result of increased turbulence or shearing at the steel-slag interface, slag can become a source of nonmetallic inclusions.Numerous studies on flow patterns in the tundish have been carried out since the introduction of the tundish. These studies were aimed at improving the flow characteristics in the tundish (Chattopadhyay, Isac, and Guthri, 2010; Cloete, 2014; Jha, Dash, and Kumar, 2001; Jha, Rao, and Dewan, 2008;"

Jan 1, 2017

By I. Silin, H. Wotruba, A. Liono, I. Volobayev, Y. Rubinstein, D. Gürsel

Old, abandoned or in situ processed and storaged tailings can be a potential source of remained valuable metals and minerals. By reprocessing of tailings, it is possible not only to achieve economical profit from recovery of valuable metals, but also to reduce environmental damage caused by tailings such as generation of acid mine drainage from sulfide minerals, mobilization of heavy metals, soils and groundwater contamination. In addition, storage facilities can be successfully redesigned with modern geotechnical requirements and monitoring to avoid a dam collapse of abandoned tailings. In this case study, the processing of low grade abandoned tailings was investigated. Copper (0.15%), cobalt (0.032%) and gold (0.35 ppm) were determined as main valuable and recoverable metals. Cobalt occurs as cobaltite and cobaltiferrous pyrite, while chalcopyrite represents copper. The fine fraction of tailings below 32 μm is enriched with cobalt and copper. Preliminary test-works with initial tailings sample were aimed to recover copper, cobalt and gold. The previously tested magnetic and gravity separation could not recover the metals in a pre-concentration step. Flotation tests of the tailings sample had shown a suitability for flotation without previous regrinding of the tailings. The valuable minerals are first proposed to be recovered by collective flotation, followed by a selective circuit with production of a low grade copper concentrate and a cobalt bearing pyrite concentrate. Based on various tested collectors, amounts of sulfidisation agents and activators, a suitable reagents regime was determined and used for up-scaling by locked cycled test. Keywords: reprocessing, tailings, copper, cobalt, gold, flotation, cobaltite, cobaltiferrous pyrite

Jan 1, 2020

By F. Shi , D. Lay, C. Antonio

High Voltage Pulse (HVP) technology has the potential to transform traditional mineral processing practice in the mining industry. HVP pre-treatment has been shown to enable ore preconcentration, achieve ore pre-weakening and improve mineral liberation. In order to improve the efficiencies of these novel HVP applications, it is essential to understand how HVP operational factors affect ore breakage in HVP pre-treatment. A two-level fractional factorial experiment using two rock samples, a gold-copper ore and a basalt sample, was performed to determine which factors have statistically significant influences on breakage probability, size reduction, and energy efficiency, and which factors have insignificant influences. Operational factors investigated include applied voltage, electrode gap, number of pulse discharges, the number of rocks being processed per batch, and rock size. In total, 1920 batch tests were conducted. For ore breakage characterised in terms of breakage probability and the degree of size reduction during HVP pre-treatment, the dominant factors were identified to be the number of pulse discharges, voltage, and the number of particles present in the processing zone. As all these three factors are related to the specific energy, it is concluded that the specific energy is the most important factor controlling ore breakage in HVP treatment. In terms of the efficiency by which spark energy is transferred from the generator energy, the factors found to have the most dominating influence were the particle size, the number of rock particles present in the processing zone and the voltage. Increasing the values of these factors reduced the loss of HVP energy during the energy transfer process. The factorial experiment using the two ore samples with vastly different mineralisation produced similar results. This proves that the dominant factors affecting HVP breakage are generally applicable to different ores types. Keywords: High voltage pulse, ore breakage, factorial experiment, specific energy

Jan 1, 2020

This paper examines the new water-hydraulic (hydropowered) drill rigs that have been developed and proven in the last decade primarily in tabular, shallow-dipping, narrow-reef hard-rock South African mines. These include drill rigs for flat-end tunnel development, narrow inclined raises and winzes, large inclines and declines and longhole-based developments such as ore passes and vent raises. The hydropower technology rigs offer advantages both in safety and performance over traditional compressed-air-powered, hand-held development, and are generally more cost-effective than imported oil electro-hydraulic drill rigs. Furthermore, hydropowered rigs are inherently energy-efficient. The benefits of hydropower are discussed and a ?comprehensive development model? is presented which demonstrates that ore-bodies can be accessed in significantly shorter times. ?Localized? half level hydropower systems are introduced and a range of ancillary equipment available is listed.

Jan 1, 2012

By H. Zhong, S. Wang, Q. Sun

The flotation performance of 2-(benzylthio)-acetohydroxamic acid (BTHA) to diaspore was first evaluated by micro-flotation tests. The adsorption mechanism was further investigated through adsorption experiments, molecular dynamics simulation, zeta potential and X-ray photoelectron spectroscopy (XPS). The results demonstrated that BTHA had a stronger ability to collect diaspore in comparison with another diaspore collector, benzohydroxamic acid (BHA), especially under the condition of weak alkalinity, the flotation recovery can reach 90%. The more negative interaction energy (ΔE) between BTHA and diaspore from molecular dynamics simulation results revealed that BTHA had an easier adsorption ablity onto diaspore than BHA, which matched with adsorption results. The zeta potential and XPS revealed that Al atoms might bond with -C(=O)NHOH by formation of Al-O bonds. Keywords: Diaspore, flotation; adsorption; 2-(benzylthio)-acetohydroxamic acid

Jan 1, 2020

By R. Letsaole, H. Mabowa, J. Sehat, J. Tshilongo, T. Rampfumedzi, N. Ntsasa, A. Mkhohlakal1

This study explores the use of co-collectors to enhance the recovery and determination of rhodium during fire assay with lead collection, followed by acid dissolution using conventional hot plate methods. Rhodium, a critical platinum group metal, poses analytical challenges due to its low natural abundance and complex chemistry. Among the co-collectors tested, palladium and tellurium demonstrated significantly improved rhodium recoveries, ranging between 100% and 120%, whereas silver resulted in poor recovery and higher error margins. These findings highlight that co-collectors can enhance the efficiency and sensitivity of platinum group metal analysis, although their effectiveness is dependent on the chemical interaction with the target element. Acid dissolution was essential to ensure complete digestion of prills prior to analysis, enabling accurate quantification of rhodium. Overall, the findings suggest that palladium and tellurium are effective co-collectors for rhodium determination in fire assay, while silver and lead flux alone are unsuitable. This work provides important insight into optimising fire assay procedures for reliable rhodium analysis, with potential benefits for platinum group metals recovery and economic evaluation.

Mar 6, 2026

By Y. Jeong, K. Kim

Excess water can lead to instability and even failure in tailings storage facilities (TSFs). Simply reducing the amount of water in TSFs could be the best way to ensure the safety of nearby communities. In this case study we investigated the effects of reducing the water content in tailings slurry at a copper-cobalt-zinc mine in Mexico. An environmentally friendly polymer was used as a drag reduction agent (DRA) to offset the increase in solids percentage. The potential effects of the increased solids concentration on the tailings transportation system were also assessed. A series of ‘what if’ studies was conducted to assess whether adding the polymer would allow the solids concentration to be increased without changing the pressure loss in the tailings pipeline. The studies entailed conducting pipe loop tests to investigate these changes under various solids/ polymer concentrations and then constructing a computational fluid dynamics (CFD) simulation model using the test results. The validated model was used to determine the optimal polymer percentages needed to maintain the same pressure loss under baseline (30% solids) conditions, and to assess the potential risks (clogging, increased erosion rates) to the pipelines. The potential water savings were found to be significant, varying from about 1.852 Mm3/a at 35% solids to 3.915 Mm3/a at 45% solids.

Dec 13, 2023