Search Documents

By H. Cevizci

"Numerical simulation of the plaster stemming method (PSM) was performed and compared with the conventional drill cuttings stemming method (DCSM). Many earlier in situ tests have proved that PSM can use the blast energy more efficiently than DCSM. Despite PSM generating more blast vibrations, it has advantages over DCSM such as better fragmentation and lower cost per unit volume of rock blasted. In this study, numerical simulation with Autodyn software using a 2D tool was employed to prove the efficiency of plaster stemming by comparing parameters such as pressure, Y-velocity, Y-force, internal energy, acceleration-Y, and compression. For example, the maximum pressure attained at the top of explosive column was 7 395 MPa for DCSM whereas it was as high as 11 945 MPa for PSM. Most of the computed parameters were significantly higher in PSM than those obtained for DCSM. This paper is the first study elucidating the efficiency of PSM by numerical simulation. It is concluded that PSM can save substantial amounts of money and effort. IntroductionThe stemming of blast-hole collars in surface mines with an inert material redirects blasting energy to the rock more efficiently, thus the blast-induced energy is utilized more effectively in breaking rock. With proper stemming, the gases should not escape due to loose stemming material. More efficient stemming with better confinement therefore increases the blast fragmentation. In addition, the distance of scatter is increased, giving rise to a looser rock pile that can be more easily loaded and transported. In order to improve the performance of a blast, stemming is used to help maintain the gas pressure over time (Konya and Konya, 2018). Proper stemming has been shown to increase the explosive efficiency by over 41% (Snelling and Hall, 1912).The most common stemming material in open pits and quarries is drill cuttings because of their ready availability at blast sites and the drill cuttings stemming method (DCSM) is a low-cost method. However, it has a major disadvantage in that dry drill cuttings eject very easily from blast-holes during an explosion, thus a great percentage of the blast energy is wasted and lost to the atmosphere. Cevizci (2012, 2014, 2013, 2017) studied blasting parameters in open pits and obtained better results with the plaster stemming method (PSM) in many limestone, basalt, and clay quarries. Moulding plaster is preferred for stemming because of the fast hardening time of 25–30 minutes."

May 1, 2019

By P. O. Akinseye, F. T. Cawood

Mineral royalties are one of the oldest forms of mining taxation, and were initially introduced to extract economic rents from mining. Over time, the royalty regime has become more complex as it was identified as an important policy instrument that can achieve more multi-faceted outcomes. Such a multi-tiered approach in the use of the royalty instrument is also the case with South Africa. With South Africa’s new mineral royalty regime now in place for ten years, it is perhaps time to assess its impact and effectiveness. To carry out this assessment, an econometric evaluative study was undertaken using four major commodities in South Africa, namely gold, platinum, iron ore, and coal. The study explored five different policy options for government to consider and tested them to determine the most favourable one that will realize the regime’s policy objectives. After the assessment, two major options stood out. Hence, this paper seeks to highlight which of the two options is the most favourable for consideration by policymakers. Based on that study, we find that the current structure is effective, but also recommend that the factors in the formula for refined minerals be ‘modified’ to reduce the capped profitability ratio from the current 60% to 30% and the maximum royalty rate for refined minerals from 5% to 3%. The minimum rate of 0.5% during times of depressed mineral prices and no or low profitability will not be affected.

Dec 1, 2021

By P. P. Kim, M. Tangstad, T. A. Larssen

"The kinetics of MnO and SiO2 reduction in SiMn slags based on Assmang/Comilog ore and HCFeMn (highcarbon ferromanganese) slag were investigated between 1500 and 1650°C under a CO atmosphere. The results showed that charges containing HCFeMn slag had relatively faster reduction rates than those without. The difference in the driving force for MnO reduction was insignificant among the SiMn slags at 1500°C, which implies a low contribution of the driving force for reduction rate. The slag viscosities were also rather similar, around 1 poise at 1500°C, which could not explain the different reduction rates. Instead, the different charges containing various sulphur contents are believed to give rise to the varying reduction rates. The estimated activation energies for MnO reduction were around 500–920 kJ/mol for charges containing HCFeMn slag, and between 250–300 kJ/mol for those without. Based on the estimated kinetic parameters, the considered rate models were able to describe the reduction of MnO and SiO2 in SiMn slags between 1500 and 1650°C. IntroductionManganese ferroalloys such as ferromanganese (FeMn) and silicomanganese (SiMn) are important ingredients in steel production due to the beneficial effects of manganese on the physical properties of steel. Mn enhances the strength, toughness, and hardness of steel products, and both Mn and Si are used as deoxidizers to prevent the development of porous structures (International Manganese Institute, 2014; Olsen, Tangstad, and Lindstad, 2007; Subramanyam, Swansiger, and Avery, 1990; Tomota et al., 1987).The thermodynamic background of manganese ferroalloys is well established (Olsen, Tangstad and Lindstad, 2007), but kinetic information is rather scarce, especially for the SiMn process (Tranell et al., 2007; Tore-Andre Skjervheim, 1994). The absence of kinetic information makes it more difficult to understand the reduction mechanisms of MnO and SiO2. It is not clear how different raw materials affect the SiMn process. The main metal-producing reactions in the SiMn process are described by Equations [1] and [2]:"

May 1, 2019

By C. Yi, M. Onifade, B. Genc, S. Dineva, T. Zvarivadza, M. Khandelwal

Deep level hardrock mining faces increasing challenges from elevated in situ stresses and associated rockbursts. This study aims to develop a systematic framework for evaluating destress blasting effectiveness, with a focus on deep Swedish hardrock mines. The methodology integrates a critical review and adaptation of global best practices: advanced numerical modelling (static and dynamic simulations), field-based rock fracture monitoring using ground penetrating radar and borehole imaging, and application of rockburst prediction criteria including the strain energy storage coefficient (F), brittle shear ratio, and burst potential index. Geostatistical simulations, machine learning models, and industrial internet of things-based, real-time monitoring are proposed to enhance predictive accuracy, model calibration, and operational adaptability. Key findings show that effective destress blasting evaluation requires multi-modal integration of numerical outputs, field observations, microseismic trends, and uncertainty quantification, accounting for site-specific geological variability and dynamic stress redistribution. The study advances the field by proposing a predictive, feedback-driven evaluation framework tailored for deep Swedish mining conditions, capable of improving proactive rockburst risk management. It offers both practical tools for mining practitioners to optimise stress management, reduce seismic hazards, and enhance excavation safety, and academic foundations for future refinement of destress blasting models, geotechnical monitoring strategies, and adaptive design protocols. This research contributes to safer, more efficient deep mining operations by bridging gaps between theoretical modelling, empirical monitoring, and real-time, data-driven blast design optimisation strategies.

Jun 27, 2025

By T. Chikande

"Falls of ground pose costly hazards to personnel and equipment and thus measures should be taken to prevent them. This study endeavours to improve the support systems used in geotechnically poor ground at a Zimbabwean platinum mine by analysing the status quo and recommending an effective support system. Various techniques were used to determine the quality of ground conditions, predict the rock mass behaviour, and to identify the appropriate rockbolt type. An analysis of the current ground control methods and their limitations was also undertaken.The results showed that the current support system and mining practices in poor ground need to be modified to improve safety and productivity. Stoping overbreak is influenced by poor ground conditions and the explosives currently used. The use of emulsion is recommended to replace ANFO. Redesigning of pillars is also recommended in poor ground conditions. An evaluation of the current roofbolt system indicated an opportunity for improvement. With new insight on the performance of the shorter length roofbolts currently in use, a new support system was recommended taking into consideration cost-benefit analysis. Barring down using pinch bars in poor ground was seen as a risky and time-consuming exercise, hence the use of mechanical scalers is recommended to achieve zero harm and to meet production targets. Smoothwall blasting is recommended in poor ground to minimize excavation damage. Other recommendations include the use of hydrological surveys to determine groundwater levels and implement corrective measures. Both empirical and numerical modelling approaches need to be utilized in determining the optimum support. IntroductionThe presence of geological discontinuities such as faults and joints weakens the rock mass. Adequate support is critical in achieving zero harm in underground mines. This paper reviews the current support systems used in poor ground conditions at a Zimbabwean platinum mine. The area of research is located on the Great Dyke of Zimbabwe. The mine exploits platinum group elements (PGEs) and base metals. It is shallow, having a maximum depth of less than 300 m. The Great Dyke is the second largest reserve of PGEs, following the South African Bushveld Complex (Oberthur et al., 2012). It is a linear layered intrusion that extends for about 550 km with a maximum width of 11 km (Prendergast, 1989). The generalized section of the Great Dyke is almost like a trumpet, comprising layers that dip towards the centre. The reef exploited at the mine, the Mineralised Sulphide Zone (MSZ), is located in the pyroxenite layer, which is hosted in the ultramafic sequence. The MSZ is a uniform layer about 2– 3.5 m thick, dipping at around 10–14° from surface outcrop towards the axis of the basin, and located between bronzite and websterite horizons. The visible disseminated sulphide mineralization shows a typical and consistent vertical distribution of platinum group metal (PGM) and base metal values. The research was undertaken to review the current support systems used in geotechnically poor ground conditions in a bid to improve both safety and productivity."

Jan 1, 2016

By L. Cheng, Y. Liu, Z. Shen, H. Shang, Y. Li

The pre-concentration process of magnetic coarse particles can discharge waste rock or liberated gangue before milling, which is an effective means to reduce cost and increase the efficiency of the concentrator, but the weakly magnetic ore doesn’t have the effective separation method of coarse particle such as hematite, limonite, ilmenite and so on, Because the composite iron minerals contain both strong and weak magnetic elements, the pre-concentration process cannot be applied, or the existing pre-concentration process has problems of complicated configuration and high operation cost. By researching a new type of external magnetic separation technology, the pre-concentration process of composite iron ore was realised by single equipment, which can have a good recovery rate with simple arrangement. In this paper, the separation principle and structure characteristics of the external magnetic separator were researched, and the magnetic circuit characteristics of the external magnet were analysed. The laboratory tests of vanadium titanium magnetite were conducted, and the test results proved that the external magnetic separator can be applied for the pre-concentration process. The industrial application shows that a product of TFe 24.76% with 90.08% recovery, TiO2 10.10% with 91.78% recovery can be achieved from the feed of TFe 20.67%, TiO2 8.33%. Keywords: Coarse particle pre-concentration, composite iron ore, external magnet, magnetic separator

Jan 1, 2020

A Special General Meeting, followed by the February General Meeting of the Institute, was held in Kelvin House, Johannesburg, on 18th February, 1970, at 4.30 p.m. Mr J. K. E. Douglas (President) was in the Chair. There were also present 24 Members: Messrs A. R. C. Fowler, R. C. J. Goode, Prof D. D. Howat, Messrs D. G. Maxwell, J. A. Nixon, P. W. J. van Rensburg (Council Members), C. A. Border, J. C. Fritz, E. K. Gibson, P. L. Grimbeek, S. D. Hill, D. A. Immelman, P. J. Uoyd, M. Mrost, C. S. Macphail, D. G. Malan, W. D. Ortlepp, R. S. Pearson, A. J. H. Pole, Dr W. S. Rapson, L. W. P. van den Bosch, R. A. von Maltitz and Dr A. Whillier. Eight Associate Members: Dr M. I. Brittan, Messrs J. Brett, I. E. Clarke, C. L. de Jongh, W. B. Evans, D. Loubser, R. C. More O'Ferrall and G. R. Still. One Graduate: Mr T. J. Kotze. One Student: Mr J. A. Cruise. Nine Visitors: including Dr N. G. W. Cook, Messrs M. D. Labuschagne, A. Nicoll, S. Sadowski, Dr A. M. Starfield and Dr H. Wagner. Secretary: Mr D. C. Visser. Total present: 45. SPECIAL GENERAL MEETING The President: "You will have received notices of the Special General Meeting and I declare it duly constituted. In keeping with the trend of overseas and local institutes, your Council recommends that we should change our membership classification as indicated in the notes of the meeting. The new grades are proposed to replace those presently in the Constitution and By-Laws. In terms of Clause 4.8 of the Constitution a special general meeting must be held for the purpose of considering and, if approved, adopting with or without amendments, the revision of the undermentioned clauses of the Constitution, which Council now recommends should read as follows. Clause 2.2 'Corporate Members shall comprise the grades of Honorary Life Fellow, Fellow and Member', these being the equivalent of Honorary Life Member, Member and Associate Member. Clause 2.6. 'Non-Corporate Member shall comprise the grade of Honorary Fellow, Graduate, Associate and Student.' Are there any questions in regard to this proposal? If not would someone propose that these clauses be amended and adopted?" Proposer: Mr A. J. Nixon. Seconder: Prof D. D. Howat. The motion was then adopted. The President: "It is recommended that Clause 2.15 should read, 'A Corporate of the Member of the Institute shall be entitled to use the following authorised letters designating the grade of Membership in Honorary Life Fellow and Fellow, F.S.A.I.M.M. and Member, M.S.A.I.M.M.' Previously we used the letters M.S.A.Inst.M.M. and your Council considered that we should adopt the simpler lettering. Could I ask someone to propose that this amendment be adopted?" Proposer: Mr R. C. J. Goode.

By Y. Rajpal

The Hedley and Grant pillar strength formula is widely used within the South African mining industry to calculate pillar strengths in bord and pillar mining layouts, and is currently being used at Bathopele Mine. Bathopele is an operation of Anglo American Platinum near Rustenburg, mining the UG2 reef at depths ranging from 40 m to 300 m below surface. The formula includes a parameter K, which is a downrated uniaxial compressive strength value of the rock, used to calculate the strength of a pillar. At Bathopele Mine, for the shallower areas Less than 150 m the value was 33 MPa, but this was increased to 44 MPa due to the fact that rock mass conditions improved and there were no incidence of failure in the shallower areas. Underground observations showed pillars to be stable with no signs of failure, and it was questioned whether the design was not still too conservative, resulting in sub-optimal extraction ratios and consequently a loss of revenue to the mine. A trial mining section was started at the mine where the pillars were reduced from 6 m x 6 m to 5 m x 5 m and the pillar behaviour was monitored for the onset of failure. Numerical modelling was conducted using the TEXAN code to back-analyse pillar stresses in order to find a more realistic value for K. Results from the trial section indicated that the pillar design was in fact too conservative, and the value for K was adjusted to 54 MPa for future designs. This paper details the findings from underground monitoring and numerical modelling results, and includes details for further calibration of the K value in order to further optimize the extraction of the orebody.

Jan 1, 2012

By M. -H. Fillion

"Geotechnical stability analysis and design in open pit mines requires access to representative geological, structural, hydrogeological, and rock mass models. The quality and quantity of collected geomechanical data used to build such models can have significant implications in the design of safe and economically viable slopes. Data collection is a continuous process throughout the life of a mine. The process starts from exploration to conceptual/preliminary feasibility, feasibility, design and construction, operations (early production/late production), and mine closure.As geomechanical data is often limited at an early stage of a project, the estimated variability of the geotechnical factors may be larger than the actual data variability. This can potentially result in a conservative selection of the pit slope angle. Collecting additional geomechanical data at later stages of the mine development may contribute to reducing the uncertainty associated with the geotechnical properties and a steeper slope angle may be used for the design. This can result in significant economic benefits.This paper investigates the impact of access to new data over time, following a series of geomechanical data collection campaigns, on design decisions. This is illustrated by comparing the resulting slope design, at three stages of the mine project, at a South African open pit mine. To demonstrate this, a series of slope stability analyses were performed using limit equilibrium tools. For each project stage, the slope angle design was modified until a similar probability of failure of 5% or less was obtained. The corresponding factor of safety distributions for each project stage were then compared to evaluate the impact of collecting additional data on the resulting slope design.The results showed that data variability can differ significantly from one project stage to another. Data variability may be greater at more advanced project stages (i.e. a wider distribution of the factor of safety). Furthermore, the results showed that, even for the cases with greater variability, steeper slope angles were possible at more advanced stages for the proposed design requirement (probability of failure < 5%). In this investigation, as more data became available, the uncertainty associated with data variability could be sufficiently reduced to allow the selection of less conservative slope angles. This can be used as a managerial tool in developing data collection strategies and allocating the necessary funds, and can lead to important economic benefits to the mining operation."

Jan 1, 2016

By M. Handley

The Witwatersrand Basin contains by far the most gold ever found, and has hosted mining from its discovery in 1886 to the present. For many years, South Africa was the world’s largest producerof gold, nearly all of which came from the Witwatersrand. Since 2000, South Africa has fallen back several positions because of declining gold output. There are many complex and varied reasons for this; however, declining gold resources in the Witwatersrand Basin are not one of them. As far as the author knows, there are no qualified estimates in the literature of gold remaining in the Witwatersrand Basin. This paper collects mining data from several sources and then, using elementary gold accounting and error analysis, attempts to estimate the amount of gold remaining in the Witwatersrand Basin. It includes gold underground in existing and defunct mines, in evaluated ore resources, and dumps. Compiled data from 1887 to 2019 shows that 50 200 t of gold were produced by Witwatersrand mines, while it is estimated that a further 48 100 t remainunderground, both within and outside of mine leases, a further 1 600 t on the surface in tailings,and an unknown amount in rock dumps. Nearly all of this gold will remain inaccessible with current mining methods, and major technical developments in mining will be necessary before any of the gold can be categorized as a code-compliant resource or reserve. To win this prize, the mining industry will have to rethink its approach to mining, both in old mining leases and in the unexploited ground. It will also have to find effective means of preventing gold theft and informal mining, which are on the rise.

Apr 5, 2023

By Moraka N. V., van Rensburg M. Jansen

"SynopsisGoing beyond transformation claims contained in employment equity scorecards and industry compliance reports, this article provides qualitative insight into the initiatives employed and challenges experienced by mining companies in a quest to transform the mining industry. Perceptions expressed during in-depth interviews with 10 senior executives showed that the assumption that mining companies are reluctant to transform is erroneous. Results from this study suggest buy-in and commitment to transformation. This article describes specific initiatives undertaken by mining companies to transform. The most notable initiatives include staff recruitment efforts to appoint historically disadvantaged South Africans (HDSAs), staff development initiatives, as well as community development. The findings furthermore contextualize the challenges experienced by industry participants in their quest to transform. Despite accusations that industry participants are not taking responsibility for the implementation of the transformation agenda, government needs to recognize that they too have a role to play and need to appreciate and assist in the current challenges experienced by the industry.IntroductionWe need a mining sector that works. Mining employs over half a million people. It is the biggest earner of foreign exchange in our country. It also contributes about 20 billion rand directly to tax revenue. Mining also makes a far larger contribution as a buyer of goods and services, and a supplier of inputs to other sectors of our economy and other economies around the globe’ said President Jacob Zuma during the 2014 State of the Nation Address (Zuma, 2014). However, despite apparent commitment from government, enforced compliance with social and labour plans, regulations and Mining Charter targets, the South African mining industry is slow to gain local and international investor trust (Deloitte & Touche, 2013; Mashego, 2013).Industry players acknowledge that their context has changed – creating various challenges (Davis, 2014). In the past few years, such challenges included subdued commodity prices, increased working costs, constrained infrastructure, and high labour costs, coupled with poor levels of productivity, strained labour-management relations, an uncertain regulatory environment, and the inevitable maturation of the industry (Deloitte & Touche, 2013; Davenport, 2014). Mining affected communities also became more cognisant of their rights, and politicians more vocal in their expectations from their relationships with the mining giants (Davis, 2014). One of the main issues that contributed to the difficult operating conditions was claims from organized labour and Minister Shabangu that this industry is too slow to transform. Specific claims were made in terms of employment equity, fair salaries and wages for mineworkers, housing and living conditions, health and safety issues, and general working conditions (Limpitlaw et al., 2005; Miningmx, 2013; Shabangu, 2010). These claims were followed by what Gill Marcus, Reserve Bank Governor, explained as ‘unprotected strike action [that] has escalated into an uncontrolled, violent and unlawful landscape, led by a mob mentality in the absence of formal and recognised leaders’ (Mavuso,2013)."

Jan 1, 2015

By B. Matsetela, S. Amos, V. Nkuna

"The Kamoa-Kakula copper project—a joint venture between Ivanhoe Mines, Zijin Mining Group Co. Ltd, and the government of the Democratic Republic of Congo—has been independently ranked as the world's largest undeveloped high-grade copper discovery by international mining consultant Wood Mackenzie. It is a very large, near-surface stratiform copper deposit with adjacent prospective exploration areas within the Central African Copperbelt, approximately 25 km west of the town of Kolwezi and about 270 km west of the provincial capital of Lubumbashi. A phased development approach is currently envisaged. The first phase of the project involves the development of a 6 Mt/a underground mine and surface processing complex (dual stream concentrator) at the Kakula deposit, a discovery announced in early 2016. The second phase involves an integrated 12 Mt/a two-stage development, beginning with initial production from the Kakula mine, to be followed by a subsequent, separate underground mining operation at the nearby Kansoko mine, along with the construction of a smelter. Project description and locationThe Kamoa–Kakula project comprises a newly discovered, very large stratiform copper deposit with adjacent prospective exploration areas, located within the Central African Copperbelt in Lualaba Province, Democratic Republic of Congo (DRC). The Kamoa–Kakula project lies approximately 25 km west of the town of Kolwezi and about 270 km west of Lubumbashi. Ivanhoe owns a 49.5% share interest in Kamoa Holding, an Ivanhoe subsidiary that currently owns 80% of the project. Zijin Mining owns a 49.5% share interest in Kamoa Holding, which it acquired from Ivanhoe in December 2015 for an aggregate cash consideration of US$412 million. The remaining 1% interest in Kamoa Holding is held by privately-owned Crystal River.The Kamoa–Kakula project consists of the Kamoa exploitation licences (exploitation permits 12873, 13025, and 13026, which cover an area of 397.4 km2) and one exploration licence (exploration permit 703 covering an area of 12.74 km2). The Kamoa exploitation licences, approved 20 August 2012, grant Kamoa Copper the right to explore for, develop, and exploit copper and other minerals, for an initial 30-year term, expiring on 19 August 2042. The permits can then be extended for 15-year periods until the end of the mine’s life."

Nov 1, 2018

By M. H. Dehghanpoor, M. Zivdar, M. Torabi

"A hydrometallurgical route was developed to extract metals such as gold, silver, copper, and selenium from anode slime from Sarcheshmeh Copper Complex in Iran. For the extraction of copper by leaching, the anode slime was heated and stirred with 4 M sulphuric acid in the presence of oxygen. Optimal conditions for recovery of copper were temperature 80°C, mixing time 5 hours, and oxygen flow rate 2 L/min, resulting in a copper recovery of 94.47%. Silver and selenium were dissolved by leaching anode slime from which the copper had been removed with nitric acid. For gold extraction, anode slime was heated with aqua regia at 90°, and the gold then extracted with 2-ethyl-hexanol at a concentration of 0.5 M and phase ratio of 4. The extract was then stripped with soda solution at pH=10.5 and a phase ratio of 5. Finally, gold was recovered by precipitation with oxalic acid at a ratio of mass to volume 10 g/L. Total gold recovery was 80%. IntroductionDuring the electrorefining of copper, some metals are accumulated in the byproduct anode slime, which is an important source for recycling and recovery of these metals (Petkova, 1994). In this paper, a hydrometallurgical route is described for the recovery of precious metals from copper anode slime of Sarcheshmeh Copper Complex, which is located in southeastern Iran .Copper anode slime is black or gray powder with a particle size less than 200 mesh. Approximately 2 to 20 kg of anode slime is produced per ton of copper cathode. The slime is characterized by higher amount of Ag, Se, Pb, and Cu compared to other metals and a very low Au content (Khaleghi and Ghader, 2013).The copper anode slimes are composed of 11.69% selenium, 3.93% copper, 5.26% silver, 0.13% gold, and 45% barite, plus lead, tellurium, antimony, sulphur, and silica with small amounts of nickel, iron, zinc, and bismuth. Gold is one of the most important noble metals due to its wide applications in industry and economic importance, so recovery of gold from slime is more appealing than that of other metals. According to the World Gold Council (2013), the demand for gold has increased during the last decade. This increase is due not only to the increasing demands of the jewellery market, but also to the increasing demand for gold in industrial as well as medical applications (Ranjbar et al., 2014)."

Jan 1, 2016

By D. F. Malan, T. E. Oates

A recent experimental pillar extraction project at a UG2 bord-and-pillar mine presented a unique opportunity to compile a new pillar database. Currently, the South African hard rock bordand- pillar mines are designed using the Hedley and Grant formula with a modified K-value. This empirically derived formula was developed for uranium mines in the Elliot Lake district of Canada. The use of this formula for the design of pillars in South Africa is questionable. Very few pillar failures have nevertheless been observed and its current calibrations for the various reef types are possibly too conservative. A new UG2 pillar database of 66 pillars, of which seven are classified as failed, was compiled by the authors. This enabled a revised ‘first-order’ calibration of the K-value for the Hedley and Grant formula. The new estimated value for the UG2 is K = 75 MPa. This gives a pillar strength that is more conservative than the PlatMine formula. This work should nevertheless be considered as only a preliminary calibration as the database was small. Further work is also required to determine whether the exponents in the formula for the width and height parameters are appropriate for UG2 pillars.

May 3, 2023

By C. J. Pretorius

More than 30 percent of the global demand for zircon (ZrSi04) is supplied by South Africa. A significant amount of the zircon is exported, and beneficiated products are then imported for industrial applications locally. Beneficiating the zircon locally could have a positive impact on the local market, since zircon is only one of many such cases. Ammonium acid fluoride serves as an alternative anhydrous fluorinating agent for zircon in the synthesis of several metal fluoridesl.2. It provides an effective dry fluorinating method and is easier to handle than hydrogen fluoride or fluorine gas. Zircon exposed to extreme plasma temperatures dissociates and becomes more reactive. The reaction of the plasma-dissociated zircon (Zr02?SiO2) with the ammonium acid fluoride (NH4F?XHF, where x= 1 to 5) forms two main intermediate compounds (NH4)3ZrFr(s) and (NH4) 2SiF6(s), the latter decomposing to form volatile products at relatively low temperatures, providing easy separation of the silicon and zirconium compounds. The ammonium zirconate compound decomposes to form zirconium tetrafluoride (ZrF4), which can be further manufactured into zirconium metal, to name but one product. Data on the kinetics of the reaction of ammonium acid fluoride with zircon and plasma-dissociated zircon, combined with the thermo-dynamic parameters of the reaction, is essential for the development of an industrial process for the production of a precursor for the manufacturing of zirconium metal, namely anhydrous ZrF4. Both the reaction kinetics and reaction parameters will be included in this study, as well as some proof that the reaction proceeds to ZrF4 on a small batch scale. If the exact reaction parameters can be pinned down, a wide spectrum of anhydrous metal fluorides can be synthesized through this fluorination route.

Jan 1, 2012

1. Journals Quarterly Journal of tke International Tin Research Institute, edited by Colin J. Evans and published by the Institute, Fraser Road, Greenford, Middlesex UB6, 7AQ, England. Engineering, building and construction law review, edited by P. C. Loots and published every two months by Construction Law Review (pty) Ltd (P.O. Box 78020, Sandton 2146, Transvaal), R63,00 per year. 2. Publications of the Mineral Policy Sector Nepkeline syenite and feldspar by B. W. Boyd Potask by G. S. Barry Selenium and tellurium by D. A. Cranstone Sodium sulphate by G. S. Barry Tungsten byG. G. Law-West 3. Mintek reports Report M114 Analytical methods associated with the recovery of uran~um. Report M117 An assessment of tke merits of various types of balls in tke milling of ores. Report MU1 Tke determinatl:on of trace elements in coal by atomic

Jan 1, 1983

By G. Akdogan, I. J. Geldenhuys, Q. G. Reynolds

Efficient recovery of titanium from titaniferous magnetite ores continues to be a promising, yet unrealised opportunity, despite significant occurrences of titaniferous magnetite deposits worldwide and the existence of established industrial-scale practices. Current smelting processes only recover iron and vanadium, while the titanium is discarded in the waste slag. These slags are stockpiled and present massive environmental challenges, while still containing value as residual iron, vanadium and titanium. The complex mineralisation of these deposits does not allow for a significant opportunity to separate the titanium and magnetite minerals through normal physical upgrading processes. An upgrading process is therefore required to derive economic value. An efficient process technology could create an opportunity to unlock all three valuable commodities. South Africa’s Bushveld Complex, the largest known deposit of its kind in the world, is known for the high vanadium content but is also associated with relatively high concentrations of titaniferous magnetite. The quality of the Bushveld Complex was one of the drivers for the establishment of the Highveld Steel and Vanadium Company in the mid-1960s. The unfortunate demise of Highveld Steel and Vanadium created an opportunity to review current practices and evaluate the best available process for this complex ore in the context of the three elements of interest. Past and current processes, the nature of these deposits and the potential to recover titanium are assessed to highlight the potential of fluxless smelting of titaniferous magnetite to produce a titania-rich slag as feedstock to the pigment, titanium metal industry in conjunction with recovery of iron and vanadium. Ilmenite smelting practices are proposed as a suitable alternative to achieve the goal, namely sustainable processing. Keywords: Titaniferous magnetite, titanomagnetite, smelting, titania slags, comprehensive processing

Jan 1, 2020

By M. Z. Emad, M. U. Khan, A. ur Rehman

The use of stemming plugs in surface blasting is gaining popularity because of the environmental, technical, and economic advantages. Although previous studies have established the operational effectiveness of different types of stemming plugs, evaluations of the economic and ergonomic impacts are lacking, thereby hindering their application in many mining operations. Consequently, a significant proportion of mining operations end up performing less efficient blasts. We evaluated the effectiveness of three types of stemming plugs by conducting multiple full-scale production blasts. The results show that stemming plugs reduce the need for secondary blasting and increase blast performance. An economicanalysis showed that the incorporation of stemming plugs can reduce blasting costs significantly.

Jul 1, 2021

By M. Z. Naghadehi, E. Emami, J. Sattarvand, R. Battulwar

In this paper, a methodology for a computerised recognition of joint sets on 3D point cloud models of rock masses is presented. The process starts with classifying joints on a 3D rock mass surface through training a deep network architecture and validated using manually labeled datasets. Then, individual joint surfaces are identified using the Density-Based Scan with Noise (DBSCAN) clustering algorithm. Subsequently, the orientations of the identified joint surfaces are computed by fitting least-square planes using the Random Sample Consensus (RANSAC). Finally, the joint planes are classified into different joint sets, and the dip direction and dip angle for each set are calculated. The performance of the proposed methodology has been evaluated using a case study. The results show that the presented procedure is fast, accurate, and robust.

Sep 1, 2021

By B. Genc, P. Malepfane

This study proposes a new approach to reduce the environmental impact during surface mining by improving environmental factors through the incorporation of carbon footprint into strategic mine planning. Two key variables were analysed by contrasting and comparing the baseline and optimised models generated. These variables include net present value, which helps determine the financial feasibility of the mining models and their carbon emissions. The variables were analysed by using linear regression, Spearman’s correlation, a P-value hypothesis, and an exponential decay test. Results show that at Mine A the projected net present value was 62% higher than when running a baseline model. Furthermore, the net present value from the baseline model portrayed a high rate of decay at 0.667 versus 0.118 from the optimised model. This indicates the baseline model’s sensitivity to long-term project timelines and fluctuating markets. The optimised method presents an opportunity to manage emissions during the high operational costs phases. It is represented by a 31% improvement in carbon emissions during the periods of high operational costs, whilst maintaining a positive net present value when compared with the baseline model. It was shown that the optimised model presents a better chance of achieving financial feasibility and balancing environmental impact, thereby ensuring that Mine A can align with the environmental aspect of economic, social, and governance principles through lowering the carbon footprint resulting from its hauling operations.

Jan 30, 2026