Search Documents

By Charles Vaught

The U.S. Bureau of Mines evaluated the self-contained self-rescuer (SCSR) donning proficiency of 243 miners. These workers were from eight underground coal mines in the eastern United States. The objectives of the study were (1) to gather information on skill levels, since all miners in the study had prior instruction and opportunity to practice donning the apparatus, and (2) to summarize a quality control procedure useful in conducting periodic evaluations of donning proficiency. The sampling procedure used proved to be both reasonable and efficient in gathering information on training effectiveness. It also provided a good statistical base for making informed site-specific decisions regarding SCSR training needs. Results from the observed samples at each of the eight mines indicate a wide variability across sites. The rate at which miners failed to isolate their lungs varied from 3.3 to 40.0 pet. Concomitantly, proficiency rates (miners either performing adequately or demonstrating a perfect 3 + 3 sequence) ranged from 13.3 to 63.3 pet.

Jan 1, 2010

By J. E. Tress

The Bureau of Mines prepared submicron tungsten powder by reducing tungsten hexachloride with hydrogen. The particle diameters of the resulting tungsten powders ranged from 0.015 to 0.046 micron. Within the limits of the variables investigated, no clear-cut correlation was found between process conditions and final size of the powder. Oxygen was the major contaminant in the product; being present both as an adsorbed gas and as suboxides of tungsten. Studies showed that the powder yielded compacts of approximately 45 per-cent of theoretical density when compacted mechanically. Low-temperature sintering produced more rapid densification in these compacts than in compacts prepared from conventional powders. Adding up to 20 percent ultrafine powder to conventional tungsten powder caused an increase in density upon compaction with maximum densification occurring at approximately 12 percent ultrafine powder.

Jan 1, 1966

By Martin H. Stanezyk

The Bureau of Mines investigated leaching of selected copper sulfide minerals and a composite of impure flotation concentrates at elevated temperatures and pressures with ammoniacal solutions. Copper 1 (tractions of 96 percent were obtained by leaching chalcopyrite at 75° C under oxidizing conditions for 60 minutes. An extraction of 99 percent of the copper contained in the composite concentrate was obtained by leaching the product for 90 minutes at 75° C. In tests of bornite, chalcocite, and covellite, 90 to 97 percent of the copper was extracted at 20° C provided an 8-hour reaction period was used. At 75° C essentially complete dissolution of the copper from these three minerals was accomplished in 60 minutes. Additions of ammonium sulfate to the leach solutions were required to obtain high-percentage extractions of the copper from bornite, chalcocite, and covellite. Although ammonium sulfate was not required when digesting chalcopyrite, copper extraction was enhanced and less free ammonia was required when ammonium sulfate was added to the leach pulps. The chemistry of leaching copper minerals was studied. It was C, termined that chalcocite altered to covellite as one step in the dissolution When leaching iron-bearing copper sulfides, hydrated iron oxide formed on the mineral surfaces, indicating that a diffusion process prevailed. No evidence of covellite was detected.

Jan 1, 1966

By W. A. Cole

As the mines get older and the active workings get Farther and farther away from the original mine openings, it becomes increasingly difficult and expensive to ventilate most coal-mines properly. At the same time, the avenues of escape for those employed underground have become so extended' as often to make it impossible for them to make their way out of the mine in the event of a fire, mine explosion, or other emergency. Where such Conditions exist, the only satisfactory solution is to make new ventilation and emergency-escape openings near the active mine workings. At most mines this would necessitate sinking shafts, which is often slow and expensive.

Jan 1, 1945

By E. C. Baker

The Bureau of Mines estimated the economic feasibility of investing in a directional hole methane drainage project in the Pittsburgh coalbed for 5 yr in advance of mining. This report estimates the capital investment and operating cost of recovering 325 MMft3 of methane gas per year and the selling price of approximately 317 MMft3 of gas per year. The labor, equipment, and supply requirements were determined from those of a previous directional hole drilled at the Emerald Mine, near Waynesburg, PA. The cost of equipment, materials, services, and labor are in third quarter 1982 dollars. They were obtained from vendors, contractors, and the U.S. Department of Labor. Findings indicate a total capital investment of $1,381,160. Annual operating cost amounted to $167,690. At a wellhead price of $2.05 per thousand cubic feet, the sale of approximately 317 MMft3 of gas per year results in a rate of return on investment of approximately 25 pet.

Jan 1, 1984

By Karl C. Dean

The Bureau of Mines stabilized 10 acres of windblown copper mill tailings at McGill, Nev., by a combination chemical-vegetative procedure. Legumes, winter wheat, wheat-grasses, and wild rye were seeded, and the area was subsequently sprayed with a resinous adhesive chemical to stabilize the sands until the vegetation could grow. During the year since treatment, the area has been well stabilized against wind erosion. The established vegetation appears to be capable of self-perpetuation and renewal without irrigation. The cost of stabilizing the area was $135.50 per acre.

Jan 1, 1969

By Liming Yuan

[ ]

Jan 1, 2009

By L. E. Schultze

The Bureau of Mines devised a technique to recover a Zn-Pb concen-trate from a geothermal brine. More than 99 pct of the Zn and Ph was precipitated by treating the brine with H2S and controlling the pH with lime. Recycle of the sulfide precipitates increased crystal size and resulted in easily filterable products. A typical sulfide precipitate contained 53 pct ZnS, 8 pet PbS, 24 pct MnS, and 15 pct FeS. Addition of sulfide as FeS or CaS was not effective in precipitating Zn and Pb, but Zn in the brine was selectively removed with a strongly basic ion-exchange resin. A proposed flowsheet for metals recovery is discussed.

Jan 1, 1985

By A. B. Hooker, R. A. Kearns

Material used for flame safety lamp gauzes should possess the following qualities: (1) mechanical strength, (2) resistance to corrosion under service con- ditions, (3) a relatively high thermal conductivity, (4) a melting point above the ignition temperature of mine gas. Heretofore, three metals have been used for flame lamp gauzes, namely: steel, brass and copper. While each of these has the requisite qualities to some extent, none of them is an ideal gauze material. Copper gauzes lack mechanical strength, especiall, after they have been heated; brass and copper both have comparatively low melting points so that before the gas ignition is reached the gauze metal is attacked and oxidized under the action of the heat. Steel corrodes readily in damp atmos- pheres and if the lamp stands unused under these conditions for some time, the gauzes become unfit for service. Tests of these three materials have shown that steel offers the highest degree of safety. Manel metal, the natural alloy of nickel and copper, is practically noncor- rodible. Its relting point is approximately the same as that of steel. From time to time it has been suggested that this alloy might be a better gauze material than steel, since gauzes made of Monel metal should have all of the good qualities that steel gauzes possess and, in addition, would not corrode appreciably in ordinary mine atmospheres. One advocate of this use for Monel metal, the International Nickel Co., through their development engineer, Mr. Robert J. McKay, cooperated with the Interior Department, Bureau of ines, to the extent of supplying twelve sets of 30 mesh, Monel-metal gauzes for tests. Those gauzes were made up by the same lamp manufactur- er ho rade the steel gauzes used in the previous investigation. Being made by the same processes as the steel gauzes, these Manel-metal gauzes were needlessly given the same anti-rust coating that is always applied to steel gauzes to prevent any corrosion before the gauzes are used. In previous tests the Bureau of Mines had collected data as to the behavior of steel gauzes. In determining the value of Monel metal as a gauze material, it was planned to obtain similar data with Monel-metal gauzes, and thus make a direct comparison with the steel gauzes. In addition, steel and Monel-metal gauzes

Apr 1, 1923

By R. F. Abernethy

A small-scale method was developed for determining the free-swelling index of coal samples of limited quantity, especially the macerals. Results of a series of tests using a 0.3-gram sample correlated well with those by the standard method using a 1-gram sample. The standard and small-scale methods are modified to give unrestricted swelling for those coals having swelling index numbers above 7.

Jan 1, 1971

By R. V. Higgins

Many contributions to methods of forecasting the performance of waterfloods of a five-spot pattern have been made by investigators. In most of these forecasting methods, a previously selected sweep efficiency is used, and other simplifying assumptions are employed to obtain the objective. In this paper the calculated oil recoveries from several five-spot single- and multiple-layer stratified reservoirs were made with a minimum of assumptions, and because of the techniques used, no previously selected sweep efficiency was required. As a result, the accuracy of the forecast is increased. Permeability curves and continuously changing saturation gradients are used in every section of the pattern. By means of a potentiometric model, the flood pattern is divided into channels, the centers of which are the streamlines. The channels are divided into cells. As flood water enters, the permeability and saturation of each cell change with time. In this study the production from multiple-sand layers of different absolute permeability but with the same relative permeability-saturation relations are combined. The results are shown for a single- and 10-layer reservoir with a permeability variation of 0.60. The oil rate, water-oil ratio, and recovery are shown as functions of time for a 2- and 20-centipoise oil starting in primary phase and after fill-up.

Jan 1, 1962

By N. A. Gokcen

This Bureau of Mines report reviews and summarizes recent studies of the rates of chlorination of aluminous resources with CO and C12 mixtures with and without COC12. No reaction mechanism could be obtained from the existing results; however, diffusional barriers in the gas and solid layers probably control the chlorination rate in thermogravimetric experiments. Fluidized beds of particles smaller than 0.1 mm appeared to show very little solid layer diffusional barrier. For optimum chlorination the particle size should probably be less than 8 mm, the calcination temperature approximately 700° C, and the chlorination temperature from 650° to 750° C. Relatively rapid chlorination with COC12 in thermogravimetric experiments was attributed partly to the simultaneous supply of reductant and chlorinator by one gas to the sample reaction site. Comparable results for chlorination of fluidized beds with COC12 are not available. Equimolar mixtures of CO and C12 produced the optimum rate of reaction. Addition to the calcine of 10 to 20 wt-pct NaCl accelerated the rate of chlorination, and addition of SiC14 to the gas mixture decreased the rate of chlorination of SiO2 drastically, but at the expense of chlorination of significant fractions of Al2O3. Further research in various areas is suggested.

Jan 1, 1983

By Clark R. Neuharth

To assess the supply status of ultra-high-purity silicon for national defense needs, the U.S. Bureau of Mines conducted a general study of the availability of materials and processing technology for silicon used in the manufacture of infrared (IR) detectors from raw materials to the highly advanced device state. The United States possesses all of the raw materials and processing technology for IR detector-grade silicon production, but does not produce at all of the processing stages on a regular basis. Consequently, the United States continues to rely on foreign sources for some of these critical materials.

Jan 1, 1989

By R. P. Beyer

A FORTW IV computer program has been written to calculate thermodynamic properties over a desired temperature range from spectroscopic data. This program computes heat capacities, enthalpies, and entropies for monatomic, diatomic, linear, and nonlinear polyatomic gases. This research is part of the Bureau of Mines effort to provide thermodynamic data for the advancement of mineral technology.

Jan 1, 1981

By D. G. Kuehn

Mass spectrographic studies have been conducted on the positive ions and neutral species of glow discharges containing 1.0 pct S02 and 1.0 pct CO in helium. Measurements were conducted for gas pressures from 3.5 to 10.1 torr using both dc and 60-Hz ac excitation. The ion species that were observed included S+, SO+, SO+, 0+, O2+, C+, CO+, and CO2+ with lesser amounts of SO3+, (CO)2+, SCO+, and (SO?CO)+ or CS+2. Interpretation of the functional dependence of the various ionic and neutral species on pressure and applied power showed that CO reacted with the SO formed in the discharges to produce CO2 and sulfur. Deposition of elemental sulfur was observed in the plasma container.

Jan 1, 1973

By J. W. Horne

The United States Bureau of Mines in cooperation with the State of Colorado at the University of Colorado has conducted experiments to determine the amount and composition of the non-condensable gases evolved when crude shale oil is distilled under pressure. Hydrogen sulphide is one of the components found in the complex mixture of Gases produced by the distillation of shale oil under pressure. This paper deals with the apparatus and method used in determining the amount of hydrogen sulphide evolved in the laboratory experimental cracking stills. The study required a complete extraction of all the hydrogen sulphide from the gas stream after it left the water-cooled distillate condensers and before the gas stream entered the charcoal absorber for removing the light naphtha. In devising the method it was necessary to take into account a constant variation of velocity, pressure, and percentage of sulphide in the total gas stream coming from the still. Ordinarily, the quantitative determination of hydrogen sulphide in gas is made by analyzing small samples taken at regular intervals. This estimation can be accomplished by use of the Bunts gas burette as modified by Tutriler, or by a similar method. In the industries where the flow of gas is constant and of uniform composition, this practice is sufficiently accurate for plant control. For experimental work where many variables have to be taken into consideration, as in the case at band; these methods are not applicable.

Jan 1, 1931

By W. P. Diamond, B. M. Bench, C. M. McCulloch

Coalbeds exhibit a directional permeability, with the maximum permeability oriented parallel to the face cleat. Thus, the most efficient pattern of vertical degasification holes for a coalbed is dependent upon cleat orientation. Surface joints, infrared photolinears, and Ronchi grating photolinears were investigated as potential estimators of subsurface cleat orientation. Cleat orientations were masured in 18 mines, in the Pittsburgh coalbed in southwestern Pennsylvania and northern West Virginia to be used as a standard against which prediction techniques would be evaluated. Two cleat systems with a strong geographic segregation were measured in the study area: N 67° W - N 28° E (95° separation) for the north, and N 76° W - N 17° E (93° separation) for the south. Directional data obtained from the three techniques investigated yielded satisfactory regional predictions of cleat orientation. Analysis of surface joints was the only technique considered sufficiently reliable on a local basis. Prediction of cleat orientation is based on the pairing of the principal directional sets into all reasonable combinations of fundamental systems. The system or systems composed of the most dominant sets nearest to 90° separation are likely to be a reliable prediction of cleat orientation. The most dominant set of the system selected is likely to be the face cleat.

Jan 1, 1976

By John Nagy, Austin R. Cooper

Information is presented on the pressure and rate of pressure development during a dust explosion . The data were obtained in laboratory studies in a 75- cubic inch vessel with mineral , agricultural and chemical dusts . The factors investigated include dust concentration , oxygen concentration of the atmosphere , admixed inert powder , and admixed moisture . Information is given also on the effects of these factors on the composition of the atmosphere after the explosion .

Jan 1, 1964

By Robert P. Vinson

A sequential sampler, based on the Archimedes screw, has been developed by the Bureau of Mines. Its initial purpose was to collect air samples during tracer gas studies in underground mines. However, the basic concept can be applied to other sampling needs, including sampling of liquids. A prototype was built and successfully tested in the Bureau's Experimental Mine at Bruceton, Pa. The simple design makes the sampler inherently durable and low in cost.

Jan 1, 1976

By R. P. Maloney

The Bureau of Mines conducted a reconnaissance of the less accessible parts of the Beluga River coalfield in August 1957 to determine, if possible, which areas were most favorable for developing large reserves of coal suitable for open-pit mining. Several outcrops of subbituminous coal were observed within an area about 30 miles long and 3 miles wide; neither the length nor the width of the coal-bearing area was delineated by the examination. Coal beds 30 feet thick or more outcrop at two places, and beds 5 to 20 feet thick or more outcrop fairly abundantly along the Beluga River and its tributaries The coal measures appear to occur in a series of folds. The overburden comprises glacial gravels and poorly cemented sandstones and ranges from 20 to 400 feet in depth. Few partings were seen in any of the coal beds. Samples ranged in calorific value from 6,240 to 8,246 B. t. u. on an as-received basis. Adequate water is available for stripping by hydraulic methods.

Jan 1, 1958